AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide A6 1995 C5 / 2.G AUDI AUDI https://www.carmanualsonline.info/img/6/995/w960_995-0.png AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide
Trending: wheel bolt torque, ESP, ad blue, cruise control, tow, oil, oil temperature

Page 11 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-10
 
  
15 - 
Valve spring retainer 
16 - 
Valve spring 
17 - 
Valve stem oil seal 
Replacing with cylinder head installed   
page 15
-47
 
18 - 
Rubber/metal seal 
Always replace
19 - 
Seal Always

Page 12 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-11
 
  
24 - 
Shutter wheel for Camshaft Position 
(CMP) sensor -G40- 
Note position (notch on camshaft)
25 - 
Washer Conical
26 - 
Bolt 25 Nm (18 ft lb)
27 - 
Camshaft Position (CMP) sensor -G40-

Page 13 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-12
      
Cylinder head with oil lines on the camshaft 
bearings  
    
If connectors are misaligned, oil line bores are exposed (arrows).  Fig. 3  Installation position of intake camshaft oil line

Page 14 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-13
      
All models  
    
Sealing contact surfaces between bearing cap and cylinder head  
CAUTION! 
Part numbers are listed here for reference only. Always check with 
your Parts department for

Page 15 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-14
      
Cylinder head oil seals, replacing
 
     
Oil seal for camshaft drive (left and right 
cylinder heads)  
     
-  Rotate engine to Top Dead Center (TDC).
     
-  Remove toothed belt   p

Page 16 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-15
      
Oil seal on Camshaft Position (CMP) sensor 
(left and right cylinder head)  
     
-  Unbolt Camshaft Position (CMP) sensor.
     
   Tightening torque: 10 Nm (7 ft lb)
     
-  Unbolt sh

Page 17 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide -  Install pull sleeve from 3241 seal installer onto camshaft.
Pa
ge 17 of 62 Valve 
gear, servicin
g
11/21/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE03

Page 18 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-16
 
    
Rear sealing flange (left cylinder head)  
The sealing flange and rear oil seal on the left cylinder head must be 
replaced together as follows:  -  Press seal flush using 3241/1 press sl

Page 19 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-17
 
    
-  Apply thin coat of sealant 454 300 A2 to hatched areas on double 
bearing cap, install and tighten to 10 Nm (7 ft lb). 
-  Install pull sleeve from 3241 seal installer onto camshaft.

Page 20 of 62

AUDI A6 1995 C5 / 2.G AHA ATQ Engines Valve Gear User Guide 15-18
      
Cylinder head, removing and installing
 
     
Note:  
     The following instructions apply to the left 
cylinder head. 
     
Removing  
     
Lock carrier in service position   page 13
Page:   < prev 1-10 11-20 21-30 31-40 41-50 51-60 ... 70 next >
Trending: tow, ad blue, cruise control, ESP, oil temperature, oil, wheel bolt torque