lock AUDI A6 2005 C5 / 2.G Electrics System Training Manual

Downloaded from www.Manualslib.com manuals search engine Audi
Audi A6 2005>
2005 (5)
Saloon
BBJ 3.0l Motronic / 160 kW Guided fault-finding
Function/component selection
Selecting a function or component
Electrical system (Rep. Gr. 01; 90 - 97)
01 – Self-diagnosis systems
61 – Battery control
J644 – Control unit for power management, Functions
A – Battery, Charge level
A – Battery, Battery testing
J644 – Power management, General description
J644 – Control unit for power management, Coding
J644 – Read out history data
J644 – Power management, Read measured-value blocks
J644 – Power management, Query fault memory
J644 – Data link tests for generator voltage
J644 – Replace control unit
J644 – Power management, Activate/deactivate Transport mode
Battery change history
Data for the last three battery changes is stored.
Power balance history – driving (= engine on)
The power balance and duration of the last five
journeys are logged.
Power balance history – idle (= engine off)
The power balance and duration of the last five idle
times are logged.
Other data is not relevant for Customer Service.
History dataThe diagnosis tester can be used to read out
data from the control unit for power management,
which makes it much easier to analyse the on-board
power supply and the battery.
Open-circuit voltage history
If the battery open-circuit voltage is less than the
threshold values of 12.5 volts, 12.2 volts and
11.5 volts, an entry is written to the history data.
The last four entries can always be read out.
Voltage measurement starts when
– CAN Convenience is in Sleep mode and
– terminal 15 is switched off for at least 2 hours
and
– the vehicle’s power consumption is < 100 mA.
Voltage measurement ends when
– the voltage increases or
– the current increases or
– the control unit triggers Sleep mode or
– the control unit detects a new battery.
Closed-circuit current history
If the closed-circuit current exceeds the threshold
value of 50 mA, an entry is written to the history
data. The last ten entries can be read out.
Current measurement starts when
– CAN Convenience is in Sleep mode and
– terminal 15 is switched off for at least 2 hours
and
– the vehicle’s power consumption is > 50 mA.
Current measurement ends when
– the current decreases or
– the control unit triggers Sleep mode.
Breakdown analysis
If the control unit for power management detects
the status "Cannot start vehicle", an entry is written
to the history data.
Cut-off level history
Data for the last 15 cut-off levels is stored.
Steady battery dischargeThe battery condition is 100 % when the battery is
charged.
As soon as cut-off level 1 is activated, the MMI
"Battery condition" display drops to 90 % and then
goes down to 60 % in steps. If cut-off level 1, 2 or 5
is set when the display reads 90 %, the message
"Power-saving mode active" app ears fo r a sho r t time
on the central display of dash panel insert J285.
In addition, the battery symbol in the dash panel
insert indicates power-saving mode for the entire
load switch-off duration.
As soon as cut-off level 3 is activated, the "Battery
condition" display drops to 50 % and then goes
down to 20 % in steps.
If the battery condition drops to 10 %, cut-off level 6
is active. In cut-off level 6, the message
"B AT TERY LOW" appears in the central di splay of the
dash panel insert after the ignition is switched on.
326_061 326_061
326_036
POWER-SAVING
MODE
ACTIVE
BATTERY
LOW
Battery condition
Cut-off levels 1, 2 or 5
Cut-off level 3
POWER-SAVING
MODE
ACTIVEBATTERY
LOW
Time/MinutesCut-off level 6
Time/MinutesPOWER-SAVING
MODE
ACTIVE
12 326_123

Downloaded from www.Manualslib.com manuals search engine Convenience electricsFunction diagramLegend
E369 Central locking button for outer door handle,
driver’s side*
E370 Central locking button for outer door handle,
passenger’s side*
E371 Central locking button for outer door handle,
rear left*
E372 Central locking button for outer door handle,
rear right*
E408 Button for access and start authorisation
E415 Switch for access and start authorisation
F272 Outer door handle switch, driver’s door*
F273 Outer door handle switch, passenger’s door*
F274 Outer door handle switch, rear left*
F275 Outer door handle switch, rear right*
F305 Switch for gearbox position P**
G415 Sensor for outer door handle contact,
driver’s side*
G416 Sensor for outer door handle contact,
passenger’s side*
G417 Sensor for outer door handle contact,
rear left*
G418 Sensor for outer door handle contact,
rear right*
J53 Starter relay
J329 Voltage supply relay, terminal 15
J386 Door control unit, driver's side
J387 Door control unit, passenger's side
J388 Door control unit, rear left
J389 Door control unit, rear right
J518 Control unit for access and
start authorisation
J623 Engine control unit
J694 Voltage supply relay, terminal 75x
J695 Starter relay 2
J723 Antenna read-in unit for keyless access
authorisation*
R47 Antenna for central locking and
anti-theft warning system
R134 Antenna on driver’s side for access
access and start authorisation*
R135 Antenna on passenger’s side for access
access and start authorisation*
R137 Luggage compartment antenna for access
access and start authorisation*
R138 Passenger compartment antenna 1 for
access and start authorisation*
* only for vehicles with Advanced Key
** only for vehicles with automatic transmission
1 Terminal 50 (to starter B)
2 CAN Convenience High
3 CAN Convenience Low
4 P/N signal from control unit for
automatic transmission J217**
5 Terminal 58s (lighting)*
6 Signal from brake light switch F*
Positive supply
Input signal
Output signal
Ground
Bi-directional line
13
Access and start authorisation
Start request
Ulock

Downloaded from www.Manualslib.com manuals search engine 16
The Advanced Key system was introduced with the
Audi A8 '03 and has been fundamentally revised for
the Audi A6 ’05.
The most important new feature is that the control
unit for access and start authorisation has been
combined with the actuator for steering column
locking.
Convenience electrics
System overview

Downloaded from www.Manualslib.com manuals search engine 17
326_147
1 Door control unit, driver's side J386
2 Control unit for on-board power supply J519
3 Control unit for access and start
authorisation J518
4 Switch for access and start authorisation E415
5 Central locking button for outer door handle,
driver's side E369
Outer door handle switch in driver’s door F272
Sensor for outer door handle contact,
driver’s side G415
6 Antenna read-in unit for keyless access
authorisation J723
7 Antenna on driver’s side for access
and start authorisation R134
8 Door control unit, rear left J388
9 Passenger compartment antenna 1 for
and start authorisation R138
10 Door control unit, passenger's side J38711 Central locking button for outer door handle,
rear left E371
Outer door handle switch, rear left F274
Sensor for outer door handle contact,
rear left G417
12 Central locking button for outer door handle,
passenger’s side E370
Outer door handle switch in passenger’s
door F273
Sensor for outer door handle contact,
passenger's side G416
13 Antenna on passenger’s side for access
and start authorisation R135
14 Door control unit, rear right J389
15 Antenna for central locking and
anti-theft warning system R47
16 Central locking button for outer door handle,
rear right E372
Outer door handle switch, rear right F275
Sensor for outer door handle contact, rear
right G418
17 Boot antenna for access
and start authorisation R137

Downloaded from www.Manualslib.com manuals search engine 18
Division of functions
System control is broken down into three basic
modules:
– the control unit for access and
start authorisation J518,
– the antenna read-in unit for keyless access
authorisation J723 and
– the switch for access and
start authorisation E415.
All three components communicate with each other
over a local single-wire bus.
The control unit for access and start authorisation is
the master of the system and a participant on
Convenience. The same control unit is installed for
all system versions.
The antenna read-in unit for keyless access
authorisation is only installed with the
Advanced Key option. It serves as the interface
between the antennae, sensors and the control unit
for access and start authorisation.
The switch for access and start authorisation is
installed in various versions, depending on the
transmission, radio frequency of the central locking
system and the Advanced Key option. An evaluation
electronic device is also integrated into the switch.
Convenience electrics
326_064
Access and
start authorisation
J518Antenna read-in
unit for
keyless access
authorisation
J723
Switch for
access and start
authorisation
E415

Downloaded from www.Manualslib.com manuals search engine 19
Ve rs i on s
The switch for access and start authorisation is
available in the following versions:
– with and without Advanced Key function
– with and without ignition key anti-removal lock
– for radio frequencies of 315 MHz, 433 MHz or
868 MHz
Functions
The switch for access and start authorisation
includes other functions apart from the ignition
switch function:
– Evaluation of the key position of the ignition
switch:
The ignition switch evaluates the ignition key
position using four switches.
The switch information is transferred to the
control unit for access and start authorisation in
binary code via the local bus and also for
monitoring purposes, via two lines.
The lock barrel in the ignition switch is not coded
mechanically, which means that the turning
movement can be performed with every
A6 '05 key.
– Safety branch for the steering lock of the control
unit for access and start
authorisation:
In addition to the switch-offs in the control unit
for access and start authorisation, the voltage
supply for the motor of the electromechanical
steering lock is interrupted in the switch for
access and start authorisation in order to
prevent the steering column locking
automatically.
If terminal 15 is switched on, the voltage supply
is always switched off.
326_066
326_067
Switch for access and start authorisation E415
ULock
326_122Emergency release

Downloaded from www.Manualslib.com manuals search engine 20
– Reading in position P of the automatic
transmission from the switch for gearbox
position P F305:
The signal is used to activate the integrated,
magnetic ignition key anti-removal lock. If the
vehicle battery is flat, the key can be removed by
pressing the mechanical emergency release.
– Reading in the information from the button for
access and start authorisation E408 (only for
vehicles with Advanced Key):
Fo r s a fe t y r e as o n s , t h e p o s i t i o n s o f t h e b u t to n fo r
access and start authorisation are evaluated by
the switch for access and start authorisation.
–
– Reading in the information from the antenna for
central locking and anti-theft warning
system R47:
The switch for access and start authorisation
passes the data, which the vehicle key sends via
remote control, on to the control unit for access
and start authorisation. The control unit
evaluates the data.
– Reading in the signal from the brake light
switch F (only for vehicles with Advanced Key):
To start the vehicle using the button for access
and start authorisation, the brake pedal must be
actuated.
– Exchanging data with the key using the
integrated read coil:
If a key is inserted into the switch for access and
start authorisation (= S contact on), the
electronics system transmits electric power into
the key via the read coil. The key then sends the
key identification into the switch via the
transponder and the read coil. This sends the
information to the control unit for access and
start authorisation.
Convenience electrics
326_069 326_068
326_065

Downloaded from www.Manualslib.com manuals search engine 21
The electromechanical steering column lock was
integrated into the control unit for access and start
authorisation.
Functions
– Terminal control:
The control unit for access and start
authorisation puts the information about
terminal 15, 75x, 50, S and P on
CAN Convenience.
The control unit also activates the relays for
terminal 15 and 75x and passes the start request
signal on to the engine control unit.– Locking the steering column:
The motor and gears for locking the steering
column are integrated into the control unit for
access and start authorisation.
The position of the lock is checked using two
integrated micro switches. Terminal 15 is only
switched on after the steering is unlocked fully.
– Immobiliser and component protection:
The control unit is the master for these
functions.
Control unit for access and start authorisation J518
326_095

Downloaded from www.Manualslib.com manuals search engine 23
Vehicl e ke y
The key has a mechanically coded hinged bit for the
lock cylinder in the driver’s door and the tailgate/
boot lid. The transponder function is integrated into
the electronics and also works without a battery.
An integrated battery powers the electronics for the
radio remote control and Advanced Key functions.
A new feature here is the bi-directional data
exchange between the radio-control key and the
control unit for access and start authorisation via
the antenna for central locking and anti-theft
warning system R47. This is used to transfer the
status of the central locking system into the key.
If a button outside of the function range of the key
is pressed, the LED integrated in the key shows the
lock status of the vehicle. The lock status displayed
is always the status, which was achieved using this
key when central locking was last actuated.
If the vehicle is opened or locked in the interim
period using a second key, this does not change the
lock status in the first key.
Furthermore, the radio frequency is changed from
433 MHz to 868 MHz for the first time in many
countries. This radio frequency is ideal for data
communication between vehicle keys and the
control unit.
Since this frequency can only be used for very short
transmission pulses, any interference from
long-term radio transmitters, such as baby phones,
wireless headsets, etc. is eliminated.
326_138
326_058 Vehicle within key range
Vehicle outside of key range,
last vehicle status is locked Signals from the key LED
Vehicle outside of key range,
last vehicle status is not locked
Approx. 4 seconds on
off
on
off
on
off

Downloaded from www.Manualslib.com manuals search engine 24
The control unit is only installed together with the
Advanced Key option.
It is located at the right of the dash panel, behind
the glove compartment.
It evaluates the signals from the outer door handle
sensors and then activates the antennae for access
and start authorisation.
The capacity-based operating sensors in the outer
door handle detect any contact on the handle and
send a signal shortly afterwards to the antenna
read-in unit for keyless access authorisation.
The antenna read-in unit evaluates the signal and
then sends a query to the vehicle key via the
antennae for access and start authorisation.
The sensors switch off after approx. 80 hours once
the vehicle is locked or after 20 actuations without
an authorised key.
Convenience electrics
326_097
Antenna read-in unit for keyless access authorisation J723
Sensors for outer door handle contact G415 - G418
326_096