ignition AUDI A7 2014 User Guide

Instruments and warning/indicator lights 25
For some vehicle functions, you can access the
trip information from the temporary memory
¢
page 26 in the line CD¢ fig. 5.
.&_ WARNING
-
- Never rely exclusively on the outside
temperature display to determine if a
road surface is icy or not . Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
slippery even at an outside temperature above
41 °F (+5 °().
- Always remember, even if the "snow­
flake" symbol (ice warning) does not ap­
pear in the display, black ice could be on
the road.
- Always reduce your speed and drive with
special care in cold weather conditions
when the chance of encountering icy
road surfaces increases.
@ Tips
- At temperatures below 14 °F (+ 5 °C) a
snowflake symbol appears ahead of the
temperature display. It is intended to re­
mind the driver to pay special attention
to
ice on the road ¢ ,&. . If the vehicle is
stationary, or if you are driving at a very
low speed, the temperature shown in the
display might be slightly higher than the
actual outside temperature . This is
caused by the heat being radiated from
the engine .
- You can select the units used for temper­
ature, speed and other measurements in
the MMI.
- For information on the audio/video and
navigation* functions, refer to the sepa­
rate MMI owner's manual.
Operation
The driver information system is operated us­
ing the buttons on the multifunction steering
wheel.
Fig. 6 Multif unctio n steerin g wh eel: operat in g th e driv­
er informat ion sys te m
Fig . 7 Dr iver informat ion syste m: o penin g the ve hicle
fu nctio ns me nu
Operating concept
"'Switch the ignition on .
"'To switch between the tabs, press the rocker
switch CD to the left or right ¢
fig. 6.
"'To access additional information below or
above, rotate the thumbwheel @down or
up.
"' To confirm a selection, press the thumb­
wheel @.
"' Press the
Iii button @ to open a sub menu
for an active tab .
"'Press the button @ to access a function for
the programmable steering wheel button* .
Accessing Vehicle functions
"'Select the first tab with the rocker switch
CD -
.. Press the button
liJ@. The Vehicle func­
tions
menu appears ¢ fig. 7.
"'To select a menu item, turn and press the
thumbwheel @.

26 Instruments and warning /indicator lights
Resetting values to zero
.,. Se lect t he on -board computer / Efficien cy
program
men u item in the Vehicle func­
tions
menu.
.,. You can now select between the long-term
memory and short -term memory .
.,. To reset the values i n a memory, press and
ho ld the thumbwhee l@ for one second .
Assigning a function to the
programmable steering wheel button*
.,. Se lect : ICAR !funct io n button> (Car )* sys-
tems
control button > Vehicle settings >
Ste ering wh eel button .
The last function se lected displays when y ou
switch the ignition on.
On-board computer
You can call up the following information in the on -board computer:
- D ate
- Drivi ng time ( h) from t he s ho rt- term memo-
ry
- Ave rag e consumption in MPG (l/ 100 km)
from the sho rt-term memo ry
- Ave rag e speed in mph (km/h) from the
s h ort-term memo ry
- Distance d riven in m iles (km) from the
sho rt-term me mory
- C urrent fuel co nsumption in MPG (l/100
k m)
- Sho rt-term memo ry overview
- Long-term memory overview
The s ho rt-term memo ry co llects driving i nfo r­
mat io n from the time the ignit ion is switched
on until it is switched off. If yo u continue dr iv­
ing within two hours after switching the igni­
tion off, the new val ues a re i ncluded when cal­
culating the cu rrent trip informa tion .
Unlike the short-term memory, the long-term
memory is not erased automatica lly. You can
select the time period for evaluat ing trip in­
formation yo urse lf.
For some veh icle functions, you can access the
tr ip i nformat io n from the tempora ry memory
i n the line
(D ¢ page 24 , fig. 5.
The current fue l cons umption can be d is ­
played using a ba r
¢page 27, fig . 10. The
average cons umption (mpg) stored in the
short-term memo ry is also displayed. E lectri ­
ca l energy can be sto red in the battery when
t h e vehicle is coasting or dr iving dow nhill (re ­
c u pera tion) . The bar w ill move toward
Cl .
Efficiency program
The efficiency program can he lp y ou to use
less fuel.
It evaluates driving information in
reference to f uel consumption and shows ot h­
er equipment influencing consumption as well
as shift recomme ndat ions .
¢ page 26. Fu el
eco nomy m essages
<=:> page 2 7 provide t ips
f o r efficient d riving. The effi ciency program
u ses d ist ance and cons umpti on d ata from trip
c om puter
1.
T o d is pl ay th e eff ic ien cy p rogram, call up Ve­
hicle functions
and se le ct t he menu o ptio n
Efficiency program. If the d ata are dele ted in
t h e eff icien cy prog ram, th ose values a re a lso
reset in tri p com puter .
@ Tips
-All s tored v alu e s will be los t if th e ve hi­
cl e battery is dis con nected .
- Fue l consum ptio ns (a ver age an d cu r­
ren t), range an d s pee d ar e disp laye d in
metric un its on Canadian mode ls.
Other equipment
Fi g. 8 Tri p comp uter: ot her equi pm en t
Req uire ment: T he e fficiency p rogram m ust be
displayed
<=:> page 26 .
.,. Turn the thumbwheel u ntil the other eq uip-
ment appears in the d isplay . .,.

Instrument s and warning /indicator lights 2 7
Other equipment that is currently affecting
fuel consumption is listed in the efficiency
program. The display shows up to three other
items of equipment @. The equipment using
the most fuel is listed first. If more than three items using fue l are switched on, the equ ip ­
ment that is currently using the most f uel is
d isplayed .
A scale @ also shows the current total con­
sumpt ion of all other equ ipment .
Fuel economy messages
Fig. 9 Dis p lay: exa mple of a fue l eco no m y m essage
F ue l economy messages are disp layed when
fuel consumption is increased by certain con ­
ditions. If you follow these fuel economy mes­
sages, you can reduce your vehicle's consump­
tion of fuel. The messages appear automati­
cally and are only disp layed in the eff ic iency
p rog ram. The fuel economy messages turn off
au tom atically after a certa in period of time.
~ T o turn a n economy message off immediate­
ly after it appears, p ress any b utton o n the
mult ifunct ion steer ing whee l.
@ Tips
-Once you have t urne d a fuel economy
m essage off, it will only appear again af­
te r you turn the ignition o n aga in.
- The fuel economy messages ar e not dis­
p layed in
every insta nce, but rat her i n in­
t e rva ls
ove r a period of t ime .
Cylinder on demand System
Applies to veh icles: w ith 4.0 TFSI engine
Fi g. 10 Inst rumen t cl us ter : fu el cons umption
To save fuel, the engine automatically turns
fo ur cy linders on or off, depend ing on the
amount of power needed . Th is act io n is not
felt by the passengers .
Displaying cylinder mode
Requirement: the on -board comp ute r is d is ­
played ¢
page 26.
~ Turn the thumbwheel u nti l the current fuel
cons umption display is shown in the instru ­
ment cluste r.
If the green bar is displayed,
y o u are driving in 4-cy linder mode.
Basic requir ements for 4 -cylinder mode
4 -cylinder drive mode is used a utomat ica lly if
certain basic requirements a re f ulfille d. These
incl ude :
-A low power ou tpu t re qui rement.
- Dr iving in t hird gear or hig her.
- Engi ne speed between 960 and 3,500 RPM .
-A warm eng ine.
Odometer
Fig. 1 1 Instrumen t cluste r: Odo mete r and rese t but­
to n

28 Instruments and warning/indicator lights
The odometer shows you how many miles
(kilometers) you have driven. You can switch
the display from miles to kilometers and vice
versa via the MMI.
Upper odometer
The trip odometer shows the distance driven
since it was last reset. It can be used to meas­
ure short distances. The last digit indicates
1/10 of a mile (100 meters).
You can reset the trip odometer to zero by
pressing the Reset button~-
Lower odometer
The lower odometer shows the total number
of miles (kilometers) driven.
Malfunction message
If there is a malfunction in the instrument
cluster,
DEF will appear in the trip odometer
display area. Contact your authorized Audi
dealer to have the problem corrected .
Time and date display
Fig. 12 Instrument cluster : cloc k and date
You can set the time and the date display in
the MMI. Refer to the MMI owner's manual
for instructions .
When you open the driver's door, the date and
time appear in the instrument cluster display
for 30 seconds .
Service interval display
The service interval display reminds you when
your next service is due .
Fig. 13 Instrument cluster: Serv ice interval display
The schedule for the next oil change or inspec­
tion is calculated automatically and displayed
accordingly. The display works in two stages:
Service reminder
30 days before the next service is due, a serv­
ice reminder appears in the display when you
switch the ignition on~
fig. 13.
After about 5 seconds the display switches
back to normal. The distance and time re­
maining are updated each time the ignition is
switched on until the date due for service is
reached.
Service due
When the due date for service is reached, the
message
Service due! appears in the instru­
ment cluster immediately after you switch the
ignition on. Additionally, a warning tone
sounds. After about 5 seconds the display
switches back to normal.
Calling up the service schedules
If or when an oil change or inspection is due,
can be shown in the MMI display by selecting
the service interval display in the car menu.
Select the
ICARI function button > (Car)* sys­
tems
control button > Servicing & checks >
Service interval displays. In new vehicles, the
schedule can only be called up after approxi- mately 500 km. ..,.

30 Instruments and warning/indicator lights
Display brightness
You can adjust the display brightness in the
MMI. The display brightness decreases auto ­
matica lly as the amo unt of light decreases.
The basic leve l of brightness is adjusted with
the instrument illumination
c:> page 47.
(D Note
To prevent scratches on the glass covering
the Head-up Disp lay, do not place any ob­
jects in the projection opening.
@ Tips
- Sunglasses with polarization fi lters and
unfavorable lighting conditions can af­
fect the display.
- A specia l windshield is needed for the
Head-up Display function.
- For information on cleaning, refer to
c:> table on poge 215.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) II! in
the instrument cluster is part of the On-Board
Diagnostic (OBD II) system.
The warning/indicator light illuminates when
the ignition is switched on and goes o ut after
the engine starts and the idle has stabilized.
This indicates that the MIL is working proper­
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv­
ing, a ma lfunction may exist in the engine sys­
tem. If the light illuminates, the catalytic con­
verter could be damaged.
Continue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erations) and have the condition corrected.
Contact your authorized Audi dealer .
If the light illuminates, the electronic speed
limiter may also be malfunctioning. For more information
r=.> page 31,
Electronic speed
limiter .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
c:> page 221.
On-Board Diagnostics
Fig. 16 Locat ion of Data L ink Con nector (DLC)
On-Board D iagnost ics monitors the compo­
nents of your em iss ion control system . Each
monitored component in your engine system
has been assigned a code . In case of a mal­
function, the component will be identified
and the fault stored as a code in the control
module memory.
T he MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery sys­
tem.
If the light illum inates after a refuelling,
stop the vehicle and make sure the fuel filler
cap is properly closed
c:> page 221.
In order to make an accurate diagnosis, the
stored data can only be displayed using spe ­
cial diagnostic equipment (generic scan tool
for OBD).
In order to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC). The DLC is located to the
right of the hood release
r=.> fig . 16 .
Your authorized Audi dea ler or a qualified
serv ice station can interpret the code and per­
form the necessary repair.
A WARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause

32 Opening and clo sing
Opening and closing
Keys
Key set
Fig . 17 Key set
@ Remot e control k ey w ith m echan ical
ke y
You can centrally lock and unlock your vehicle
and start the engine with the master key with
remote control. A mechanical key is integrat­
ed in the remote control key
r:::;, page 33 .
@ Eme rgenc y ke y
The emergency key is not intended for con­
stant use.
It should only be used in an emer­
gency. Keep it in a safe place and do not carry it on your key ring .
Key replac em ent
If you lose a key, contact your authorized Audi
dealer immediately to have the
lost key disa­
bled. Be sure to bring all your keys with you.
P er sonal c omfo rt se ttin gs
If two peop le use one vehicle, it is recom­
mended that each person always uses "their
own" master key . When the ignition is switch­
ed off or when the vehicle is locked, personal
convenience settings for the follow ing sys­
tems are stored and assigned to the remote master key .
- Automatic climate control
- Central locking system
- Amb ience light ing*
- Seat memory*
- Parking system*
- Adaptive cruise control* - Audi active
lane assist *
- Aud i side assist*
- Aud i drive select
- Night vision assistant*
- Heated steering wheel*
The stored settings are automatically recalled
when you unlock the vehicle, when you open
the doors or when you switch the ignition on.
A WARNING
-- Do not leave your vehicle unattended . Al-
ways take your ignit ion key with you and
lock your vehicle . Entry by unauthorized
persons could endanger yo u or resu lt in
theft or damage the vehicle.
- Do not leave ch ildren unattended in the
veh icle, especially with access to vehicle
keys. Unguarded access to the keys pro­
vides children the opportunity to start the engine and/or activate vehicle sys­
tems such as the power windows, etc .
Unsupervised operation of any vehicle
system by children can result in serious
injury.
(1) Tips
- The operation of the remote control key
can be temporar ily disrupted by interfer­
ence from transm itters in the vic inity of
the vehicle working in the same frequen­
cy range (e.g. a cell phone, radio equip­
ment).
- For security reasons, rep lacement keys
are only ava ilable from Audi dealers.
- For Declaration of Compliance to United
States FCC and Industry Canada regula­
tions
r:::;, page 288.

34 Openin g and clo sing
for another vehicle or a transponder is
located on the key ring.
- For Declaration of Compliance to United States FCC and Industry Canada regula­
tions ~
page 288.
Power locking system
General description
The power locking system locks or unlocks all
doors and the rear lid simultaneously.
You can lock and unlock the vehicle centrally.
You have the following choices:
- Remote master key~
page 35,
-Door handles with convenience key*
~ page 36,
-Lock cy linder at the dr iver's door
¢ page 37, or
- Power lock ing switch inside
¢ page 37.
Select ive unlocking
When you lock the vehicle, the power locking
system w ill lock the doors and the rear lid .
When unlocking, you can set in the MMI
whether only the driver 's door o r the entire
vehicle should be unlocked ¢
page 35.
Automatic locking
The automat ic locking feature locks all the ve­
h icle doors and the rear l id when you drive
faster tha n 9 mph (15 km/h).
The car is unlocked again, when the opening
function in the power locking system sw itch
or at one of the door levers is actuated . The
Auto Lock function can be turned on and off in
the MMI
¢ page 35.
Anti-theft alarm warning sy stem
If the anti -theft alarm warning system de­
tects a break- in into the vehicle, acoust ic and
visua l warning signals are triggered.
The anti-theft warning system is activated au­
tomatically when you lock the vehicle . It is de ­
activated when unlocking using the remote key, with the mechanical key, and when you
sw itch the ignition on. T
he alarm also turns off when the a larm cycle
has expired .
Turn signals
When you unlock the veh icle, the turn s ignals
flash twice. When you lock the vehicle the
turn s ignals flash once. If they do not flash,
one of the doors, the rear lid or the hood is
not locked.
Unint entionally locking your self out
In the follow ing cases there safeguards to
prevent yo u lock ing yo ur remo te master key i n
the vehicle :
- The vehicle does not lock w ith the central
loc king switch ¢
page 3 7 if the drive r's
door is open.
- On veh icles with co nvenience key*, if the
most recently used master key is in the lug­
gage compartment, the rear lid is a utomat i­
cally un locked again after it is closed.
Do not lock your veh icle w ith the
remot e ma s­
t e r ke y or co nv eni enc e ke y*
until all doors
and the rear lid are closed . In this way you
avoid lock ing you rsel f out accidentally .
Power side door clo ser *
The veh icle doors are equipped with a power
s ide door closer. When closing a door, you on­
ly h ave to let it fall light ly into the latch. The
door will then automatically close by itself
¢ & .
A WARNING
-When you lock yo ur vehicle from o utside,
nobody -especially children -shou ld re­
main inside the vehicle. Remember,
when you lock the vehicle from the out­ side the windows cannot be opened from
the inside.
- When you leave the veh icle, always take
the ignition key w ith you . Th is w ill pre­
vent passenge rs (children, for example)
from accidenta lly being locked in the ve­
h icle should they accidentally press the
power locking sw itch in the doors.
~

40 Opening and clo sing
- When the vehicle is locked, the rear lid
can be un locked separate ly by pressing
the button ~ on the master key. W hen
the rear lid is closed aga in, it locks auto­
matically.
Luggage compartment with movement­
activated opening
Applies to vehicles: with convenience key and sensor-con­
trolled luggage compartment lid
Fig . 28 R ear of ve hicle: foot move men t
Requirements: You must be carryi ng your ve­
hicle key with you. You must be standing at
the center behind the luggage compartment lid. The distance to the rear of the vehicle
should be approximately 8 inches (20 cm).
The ignition must be sw itched off . Make sure
you have firm footing .
,. Swing your foot forth and back below the
bumper
c::> fig. 28. Do not touch the bumper.
Once the system recognizes the movement,
the luggage compartment lid will open .
The luggage compartment lid will only open if
you make the movemen t as described. This
prevents the luggage compartment lid from
ope ning due to s imilar moveme nts such as
when you walk between the rear of the veh icle
a nd your ga rage doo r.
General information
In some s ituations, the function is lim ited or
tempo rar ily unavailable . This may happen if:
- the luggage compartment lid was just closed.
- yo u park close to a hedge and the branches
move back and forth under the vehicle for a
long period of time. -
you clean your veh icle, for example with a
pressure washer or in a car wash.
- there is heavy rain.
- t he bum per is ve ry di rty, fo r example after
driving on sa lted roads.
- t here i s interference to the radio signal from
t he vehicle key, su ch as from cell phones or
remote contro ls.
Rear lid emergency release
The rear lid can be released in an emergency
from the inside .
Fig. 29 Rear lid inter io r
,. Remove the mechanica l key c::> page 33.
,. Remove the cover with the mechanical key
from the rear lid
c::> fig. 29.
,. Press the lever in the direction of the arrow
until the rea r lid releases .
Child safety Lock for
the rear doors
The power child safety lock locks the rear win­
dows and prevent the rear doors from being
opened from th e inside .
Fig. 30 Sect io n fro m driver"s doo r: c hil d safety loc k
but ton s

.. To activate the child safety lock for the left/
right rear door, press the left/right button
Ii]
in the driver's door ¢ fig. 30. The light in the
button w ill turn on.
.. To deactivate the child safety lock for the
left/right rear door, press the left/r ight but­
ton
1±1 in the driver's door. The light in the
button turns off.
The follow ing features are switched off:
- The interior door handles in the rear doors,
- The power windows in the rear doors.
I n order to activate the child safety lock on
the left and the right s ide, press the two safe­
ty buttons
Ii] in succession.
Power windows
Controls
The driver can control all power windows.
Fig. 31 Section of the driver 's doo r: Cont rols
l(l 0 0 0
"' m
All power window switches are provided with
a two-position function :
Opening the windows
.. Press the switch to the first stop and hold it
until the window reaches the desired posi­
tion.
.,. Press the switch br iefly to the
second stop
to automatically open the window.
Closing the windows
.. Pull the switch to the first stop and hold it
until the window reaches the desired posi­
t ion.
.. Pull the switch briefly to the
second stop to
automatically close the window .
Opening and closing 41
Power window switches
@ Driver's door
® Passenger's door
© Left rear door
@ Right rear door
.,&_ WARNING
-When you leave your vehicle - even if on­
ly briefly - always take the ignit ion key
with you. This applies particularly when children remain in the vehicle. Otherwise
the children could start the engine or op­
erate electrical equipment (e.g. power
windows). The power windows are func­
tional until the driver's door or passeng­
er's doo r has been opened.
- Be careful when closing the w indows.
Check to see that no one is in the way, or
serio us injury could result!
- When locking the vehicle from outside,
the vehicle must be unoccupied since the
windows can no longer be opened in an
emergency .
{D Tips
-When you open the doors, the windows
automatically lower abo ut 10 mm.
- When the window in the driver's or pas­
senger's door is complete ly open, it will
raise approximately 25 mm when the
door is opened. The window will lower
again when you close the door.
- After the ignition has been switched off,
the windows can sti ll be opened or
closed for about 10 minutes. The power
windows are not switched off until the
dr iver's door or passenger's door has
been opened .
What to do after a malfunction
The one-touch open and close function must
be reactivated if the battery has been discon­
nected.
.. Pull and ho ld the power window switch until
the window is fully closed. .-

44 Clear vis ion
Clear vision
Lights
Switching the headlights on and off
Fig . 34 Instr ument pane l: lig ht sw itc h wit h all -weath­
er lig hts *
The headlights only wo rk when the ignition is
sw itched on. Wh ile start ing the eng ine or
when switching off the ig nition, the head­
lights will go off and on ly the s ide marker
lights w ill be on .
I f the system is not operating properly, a
warn ing symbol in the dr iver inform ation dis­
p lay is dis played
<=> page 23 .
Light switch -'t/., -
Tu rn the switch <=> fig. 34 to the co rrespond ing
position . When the lights a re switched o n, the
:o o; symbo l tur ns on .
0 -The lights are off or the dayt ime run ning
lights are on:
- USA models: The daytime running lights
will come on automatically when the igni­
t ion is on a nd the light switch<=>
fig. 34 is in
the
O pos it ion or the AUTO position (only in
daylight cond itions) . T he
Daytime running
lights
function can be tu rned on and off in
the MMI
<=> page 45, <=> .& .
-Canada model s: T he daytime running lig hts
will come on au tom atically when t he igni ­
t ion is on and the light switch<=>
fig. 34 is in
the
O posit io n, the :oo~ position or the AUTO
posit ion (on ly in daylight conditions)<=>.& .
AUTO -Automatic headlights swi tch on an d
off depend ing o n brightness , fo r example in
tw ilight, during rain or in tunnels<=>.& .
:oo~ -Side marker lights
io -Low beam head lights
[!QJ . Fog lights* (vehicles with Xenon p lus
headlig hts*)
~ -All-weather lights*
@I] -Rear fog lights* . When the rear fog lights
are on, the symbol
0$ on the switch will i llu­
minate .
All-weather lights*
In vehicles with al l-wea ther lights, the front
li gh ts a re a dju sted au tom atically so that you
are less like ly to see glare from your own
head lig hts, for example when driving on a wet
road.
Automatic headlight range cont rol*
T he hea dlights do not blind oncoming traffic
i f the veh icle load changes . The headlight
range also ad justs automatica lly when brak­
ing and acce lerating .
Light functions
The following light funct ions are avai lab le de­
pend ing on veh icle equipment and o nly func­
tion when the lig ht sw itch is in the AU TO posi­
tio n. You can deactivate these functions in the
MMI under
Audi adaptive light~ page 45.
Vehicles wi th St atic corn ering light* : the cor ­
nering light sw itches on a utomat ica lly when
the steering wheel is turned at a certain angle
at spee ds up to approx imately 44 mph
(70 km/h) and when the turn signa l is activat­
ed at speeds up to approx imately 25 mph
(40 km/h) . The a rea to the side of the vehicle
is illum inated better when turn ing.
Vehicles with
Dynamic curve light* : the curve
light only functions at speeds between ap­
proximate ly 6 mph (10 km/h) and 68 mph
(110 km/h) and adapts itse lf to the c urves in
the road .
~