AUDI A7 2015 Owners Manual

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Wheel bolts
Wheel bolts must always be tightened to the
correct torque .
The design of wheel bolts is matched to the
factory installed r ims. If differen t rims are fit­
ted, the correct wheel bolts with the right l ength and correctly shaped bolt heads must
be used. This ensures that wheels are fitted
securely and that the brake system functions
correctly .
In certain circumstances, you may not use
wheel bo lts from a different vehicle -eve n if it
i s the same model
~ page 296.
_&. WARNING
Improperly tig htened or maintained whee l
bolts can become loose ca using loss of
contro l, a co llision and serious persona l in­
jury.
- Always keep the wheel bolts and the threads in the wheel hubs clean so the
whee l bolts can turn easily and be prop­
erly t ightened.
- Never grease or oil the wheel bo lts and
the threads in the wheel hubs. They can become loose wh ile driving if greased or
o iled, even if tightened to the specif ied
torque .
- Only use wheel bolts that belong to the
rim being installed.
- Never use different whee ls bolts on your
vehicle .
-Always maintain the correct tighten ing
torque for the wheel bo lts to reduce the
risk of a wheel loss . If the tightening tor ­
que of the wheel bolts is too low, they
can loosen and come out when the vehi­
cl e is moving.
If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel can be­
come loose.
Q;) Note
The spec ified torque fo r the wheel bo lts is
90 ft lb (120 Nm) w ith a toleran ce of± 7,4
ft lb(± 10 Nm). Torque wheel bo lts diago-
Tire s an d wheel s 269
nally . After changing a whee l, the torq ue
must be checked as soon as possible with a
torque wrench -preferably by an author­
i zed Audi dealer or qualif ied workshop.
Low aspect ratio tires
Your Audi is factory-equ ipped w ith low aspect
ratio tires . These tires have been thoroughly
tested and been selected specifically for your model for their superb perfo rmance, road fee l
and hand ling u nder a variety of driving condi­
tions . Ask your au thorized Aud i dealer for
more details .
T he low aspect ratio of these t ires is ind icated
by a numera l of
55 or l ess in the tire's si ze
designation. The n umera l represents the ra tio
of the ti re's sidewall height in relation to its
tread width expressed in percentage . Conven­
tiona l tires have a height/width ratio of 60 or
more.
The perform ance o f low-a spe ct-r atio tire s is
p ar ticul arl y s ens it iv e to imp ro per infl ation
pressur e. It is t herefo re im porta nt t hat low
a spect ratio t ires are inflat ed to the specified
pr essure and that the inflation pressure is
r e gularly checked and ma int ained. Tire pr es­
s ure s should be check ed at lea st on ce a
month and alwa ys befor e a long trip
~ page 252 , Checking tire pressure.
What you c an do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more
easily by impact w it h potholes, curbs, gull ies
o r r idges on the road, pa rtic ularly if the tire is
u nder infla ted .
In order to minimize the occurrence of impact
damage to the tires of your vehicle, we recom­
mend that you observe the following p re ca u­
tions:
- Always ma inta in recommended inflation
p ressures . Check your tire pressu re eve ry
2 ,000 miles (3,000 km) and add air if neces­
sary .
- Dr ive caref ully on roads wi th potholes , deep
gullies o r ridges. The impact from driv ing ..,. •
•

2 70 T ire s and wheel s
through or over such obstacles can damage
your tires. Impact with a curb may also
cause damage to your tires.
- After any impact, immediately inspect your
tires or have them inspected by the nearest
authorized Audi dealer. Rep lace a damaged
t ire as soon as possible.
- Inspect your t ires every 2,000 miles (3,000
km) for damage and wear . Damage is not al­
ways easy to see. Damage can lead to loss of air and underinflation, wh ich could eventu­
ally cause t ire failu re. If you bel ieve that a
t ire may have been damaged, replace the
t ire as soon as possible.
- These tires may wear more quickly than oth­
ers.
- Please also remember that, while these t ires
deliver respons ive handling, they may ride
less comfortably and make mo re no ise than
othe r cho ices .
Reduced performance in winter /co ld
season condition s
All tires are des igned for certain pu rposes.
The low aspect ratio, ultra high pe rformance
tires orig inally installed on your veh icle are in­
tended for maximum dry and wet road per­
formance and handling. They are not suitable for cold, snowy or icy weather conditions. If
you dr ive under those circumstances, you
should equip your vehicle with all-season or
winter tires, which offer better traction under
those cond it ions. We suggest you use the rec­
ommended snow or a ll-season tires specified
for your vehi cle, or their equ ivalent.
Refer to¢
page 267 for more deta iled infor­
mat ion regarding winter tires.
Tire pressure
monitoring system
U) General notes
Each t ire, includ ing the spare (if provided),
should be checked monthly when cold and in­
flated to the inflation pressure recommended by the vehicle manufacture r on the vehicle
p lacard or tire inflation pressure label. (If your vehicle has tires of a diffe
rent size than the
size indicated on the vehicle placard or tire in­
flat ion pressure labe l, you shou ld determ ine
the proper t ire inflation pressure for those
t ires).
As an added safety feature, your ve hicle has
been equipped with a tire pressure monitoring
system (TPMS) that illum inates a low tire
pressure telltale when one or more of your
t ires is significantly under-inflated. According­
ly, when the low tire pressure telltale illumi­
nates, you shou ld stop and check you r tires as
soon as possib le, and inflate them to the
proper p ressu re. Driving on a sig nifican tly u n­
der- inflated t ire causes the tire to overheat
and can lead to tire fai lure . Under-inflation al­
so reduces fuel efficiency and tire tread life,
and may affect the vehicle 's hand ling and
stopp ing ability.
Please note that the TPMS is not a substitute
for proper tire maintenance, and it is the driv­ er's respons ibility to maintain correct tire
pressure, even if under-inflation has not
reached the level to trigger illumination of the
TPMS low tire pressure telltale .
Your vehicle has also been equipped with a
TPMS malfunction indicator to ind icate when
the system is not operating properly. The
TPMS ma lfunction indicator is combined w ith
the low tire pressure telltale . When the sys­
tem detects a malfunction, the telltale will
flash fo r approxima te ly one m inute and then
rema in continuously illum ina ted. This se­
quence will continue upon subsequent vehicle
start-ups as long as the malfunction exists.
When the malfunction indica to r is illum inat­
ed, the system m ay not be ab le to detect or
signal low tire pressure as intended . TPMS
malfunctions may occur for a var iety of rea­
sons, incl uding the insta llation of replace­
ment or alternate tires or wheels on the vehi­
cle that prevent the TPMS from functioning
properly. Always check the TPMS malfunction
telltale after replacing one or more tires or
whee ls on you r vehicle to ensu re that the re­
placement o r alternate ti res and wheels a llow
the TPM S to cont inue to func tion p roperly.

M N <( I.J "". rl I.O
"' rl
"' rl
Tire pressure indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
Fig. 205 Display: underinflation warning
Fig. 206 Display: System malfunction
Using the ABS sensors, the tire pressure moni­
toring system compares the tire tread circum­ ference and vibration characteristics of the in­
dividual tires. If the pressure decreases in one
or more tires, this is indicated in the instru­
ment cluster with a warning symbol
rD] and a
message
c:> fig . 205.
The tire pressure monitoring system must be
reset via MMI each time the pressures are ad­
justed (e.g. when switching between partial
and fu ll load pressure) or after changing or re­
placing a tire on your vehicle
c:> page272 . The
TPMS indicator only monitors the tire pres­
sure that you have previously stored. You can
find the recommended tire pressures for your
vehicle on the label on driver's side 8-pillar
c:>page247.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warning if:
- the tire pressure in one or more tires is too
low,
Tires and wheels 2 71
- the tire has structural damage,
- the tire pressure was changed, wheels rotat-
ed or replaced but the TPMS was not reset
c:>poge272.
- the spare tire* is mounted .
Warning symbols
[I] Loss of pressure in at least one tire¢.& .
Check the tire or tires and replace or repair if
necessary. The indicator light
rD] in the instru­
ment cluster also illuminates <=:>
page 12.
Check/correct the pressures of all four tires
and resetTPMS via MMI.
l!I (Tire Pressure Mon itoring System) Tire
pressure! System malfunction .
Ifljl appears
after switching the ignition on or while driving
¢
fig. 206 and the indicator light rD] in the in­
strument cluster blinks for approximately one
minute and then stays on, there is a system
malfunction. Attempt to store the correct tire
pressure
c:> page 272. If the indicator light
does not turn off or if it turns on shortly
thereafter, immediately drive your vehicle to
an authorized Audi dealer or authorized repair
facility to have the malfunction corrected.
_& WARNING
- If the tire pressure indicator appears in
the instrument cluster display, one or
more of your tires is significantly under­
inflated. Reduce your speed immediately
and avoid any hard steering or braking
maneuvers. Stop as soon as possible and
check the tires and their pressures. In­
flate the tire pressure to the proper pres­
sure as indicated on the vehicle's tire
pressure label<=:>
page 247 . Driving on a
significantly under-inflated tire causes
the tire to overheat and can lead to tire
failure. Under-inflation also is likely to
impair the vehicle's handling and stop­
ping ability.
- The driver is responsible for maintaining
the correct tire pressures. You must check the tire pressures regularly.
.

272 Tires and wheels -Under certain conditions (such as a spor­
ty driving style, winter conditions or un­
paved roads), the pressure monitor
indicator may be delayed.
- Ask your authorized Audi dealer if run­
flat tires may be used on your vehicle.
- The tire pressure monitoring system may
stop working when there is an ESC mal­
function.
- Using snow chains may result in a system
malfunction.
- The tire pressure monitoring system on
your Audi was developed using tires with
the "AO" or "RO" identification on the
tire sidewall
c:> page 260. We recom­
mend using these tires.
Reset tire pressure monitoring system
If the tire pressure is adjusted, wheels are ro­
tated or changed, the TPMS must be reset via
MMI.
• Before storing the new tire pressures, check
that the current pressures on all four tires correspond to the specified values and
adapt the pressures to the current load <=>page 247.
• Switch on the ignition.
• Select in the MMI: !CAR !function button>
(Car)* systems control button > Servicing &
checks > Tire pressure monitoring > Store
tire pressures> Yes, store now.
Do not store the tire pressure if there are
snow chains on the tire. Otherwise, a sys­
tem malfunction may occur.

M N <( I.J "". rl I.O
"' rl
"' rl
What do I do now? Emergency warning
triangle
App lies to vehicles: with emerge ncy warning triangle
The warning triangle is located on the inside
of the trunk lid .
D -
!I l
Fig. 207 Trunk lid: Warn ing triang le
.,. To open the cover, turn the locking mecha­
nism and pull the cover downward .
"' M ~
~ .. m
.,. Remove the warning triangle from its hold ­
er .
The rear lid is only designed to hold the warn­
ing triangle offered by the original accessories
program. If you would like to retrofit your ve­
hicle with a warning triangle, please contact
your authori zed Audi dealer.
Vehicle tool kit
Vehicle tool kit and jack
The vehicle tool kit is located in the luggage
compartment under the cargo floor cover.
Fig. 208 Luggag e compa rtm en t: ca rgo floo r cov er
fol ded upwa rd /spa re tir e
What do I do now? 273
Fig . 209 Tru nk l id: Ve hicle too l kit
.,. Fold the floor to the seatback with the help
of the handle .
.,. Turn the handwheel counter-clockwise
q fig. 208 and remove the spare tire to
reach the vehicle tool kit.
T he onboard tool kit includes:
- Hooks to remove the whee l covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
-Alignment pin for changing wheels
- Screwdriver with reversible blade
- Tow ing eye
-Jack
Before storing the jack, make sure it is wound
back down as far as it will go.
A WARNING
Im proper use of the vehicle jack can cause
serious personal injuries .
- Never use the screw driver hex head to
tighten w heel bolts, since the bolts can­
not attain the necessary tightening tor­
que if you use the hex head, potentially
causing an accident .
- The factory-supplied jack is intended on­
ly for your vehicle model. Under no cir­
cumstances should it be used to lift
heavy vehicles or other loads; yo u risk in­
juring yo urself.
- Never start the engine when the vehicle
is raised, which could cause an accident.
- Support the vehicle securely with appro­
pria te stands if wor k is to be performed
underneath the vehicle ; otherwise, there
is a potential risk for injury. ..,.

274 What do I do no w?
-Never use the jack s upplied with your
Audi on another vehicle, particularly on a heavier one. The jack is only suitable for
use on the vehicle it came w ith.
- Some of the on board items listed above
are provided on certain mode ls only or
are optiona l extras.
- Before you can raise your vehicle using
the jack, you must activate the jack ing
mode
Qpage 277.
Space-saving spare tire (compact spare
tire)
The spare tire/wheel is located in the luggage
compartment under the cargo floor cover. It
is intended for short-term use only.
Taking out the sp are tire
,. Fold the floor to the seatback with the help
of the handle.
,. Turn the large screw
Q page 2 73, fig. 208
counter-clockw ise .
,. Take out the spare tire .
,. Always store the vehicle tool ki t, the jack*
and the replaced t ire in the l uggage com­
partment
Q page 134.
Using the spare tire (compact spare tire )
The compact spare tire is only intended for
emergenc ies until you can reach a repair shop.
Replace it as quickly as poss ible with a s tand­
a rd wheel and tire.
There are some restrictions on the use of the
compact spare t ire. Th e compact spare t ire
has been des igned specifically fo r your type of
ve hicle . It must not be swapped with a com­
pact spare ti re from another type of vehicle .
Snow chains
For technica l reasons, the use of snow chains
on the compact spare tire is
not p ermitt ed .
If you do have to dr ive with snow cha ins and a
front tire fails, mo unt the spare wheel w ith
tire instead of a rear t ire. I nstall the snow chains on the rear tire and use it to rep
lace
the defective front tire.
A WARNING
-- Never use the spare t ire if it is damaged
or if it is worn down to the tread wear in­
d icators.
- If the spare tire is more than 6 years old, use it only in an emergency and with ex­
treme caution and careful driv ing.
- The spare tire is intended only for tem­ porary and short-term use. It s hou ld be
replaced as soo n as poss ible with the
normal wheel and tire.
- After mounting t he compact spare tire,
the t ire pressure must be checked as
soon as possible . The tire pressure of the
compact spare t ire must be 4. 2 ba r; oth­
erwise, you risk having an a cc iden t.
- Do not dr ive faste r th an
50 mph (80 km/
h). Yo u ris k having a n accident.
- Avoid full-throttle acceleration, heavy
b rak ing, and fast corne ring. You risk hav­
ing
('I n accident.
- N ever d rive using more than one spa re
wheel and ti re. You r is k having an ac ci­
dent.
- Normal summer or winter t ires must not
be mounted on t he compa ct spare w heel
r im.
- For technica l reasons, the use of tire
ch ain s on the sp are tire is not permitted.
If i t is necessary to drive with tir e c hains,
the spare wheel must be mounted on the
f ront ax le in the event of a flat in a rear
tire. The new ly available front whee l
m ust then be insta lled in place of the
rear whee l w ith the flat tire. Installing
the t ire chain before mounting the whee l
a nd tire is recommended .
- Loose items in the passenger compart­
ment can cause se rious personal injury
du ring hard b rak ing or in a n accident.
Never store the i nflatable spa re tire or
jack and tool s in the passenge r compart­
men t.

M N <( (.J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
level gro und before you stop¢.&_ .
.. All passengers should
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il) ¢.&_ .
.. Engage the
parkin g brake to prevent your
vehicle from ro lling unintentionally ¢.&_ .
.. Move
selecto r le ver to p osition P ¢ .&_ .
1> Ifyou are towing a trai ler, unh itch the tra iler
from your vehicle .
.,. Take the
jack and the spare tire out of the
luggage compartment
¢ page 273,
¢ page 274 .
.8, WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low t hese safety precautions:
- If you have a flat t ire, move a safe dis ­
tance off the road. Tur n off the eng ine,
turn the emergency f lashers on and use
other warning dev ices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the ve hicle and well
away from the road and traff ic.
- To help p revent the vehicle from moving
s u dden ly and possibly slipping off the
jack, always fully set the parking brake
and block the wheel diagonally opposite
the wheel being changed. Whe n one
front wheel is lifted off the ground, plac­ ing the A utomat ic Transm iss ion in P
(Pa rk) will
not p revent the vehicle from
moving.
- Before you change a wheel, be su re the
ground is level and fi rm. If ne cessa ry,
use a st urdy board under the jack.
-
What do I do now? 275
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­ partment
c::>page 134.
(D Tips
Before changing the whee l, you must acti­
vate the jacking mode, so that the auto­ matic controls for the Adaptive Air Sus­
pension* do not make it more d iff icult to
lift the vehicle with the jack
c::> page 2 77 .
Changing a wheel
When you change a wheel , follow these­
quence described below s tep-by-s tep and in
exactly that order .
l. Activate the vehicle jack mode*
¢page 277 .
2. Remove the decorativ e wheel co ver* . For
more details see also
c::> page 2 76, Deco­
rative wheel covers
or c::> page 2 76,
Wheels with wheel bolt caps .
3. Loosen the wh eel bolt s ¢page 277.
4 . Loca te the p roper moun ting poin t for the
jack and align the jack be low that point
¢ page 277 .
5.
R ais e the car with the jack¢ page 2 77.
6. Remove the
wheel with the flat tire and
then install
the spar e c::>page 279.
7. Tighten all whee l bolts lightly .
8.
Lo wer the vehicle with the jack .
9 . Use the wheel bolt w rench and
firmly
t ighten al l wheel bolts ¢ page 2 77.
10 . Replace the decorative
wh eel c ov er* .
11. Deactivate the vehicle jack mode* in the
MM I:
ICARI f u nction button > (Car )* sy s­
tems
contro l button > S erv ici ng & che cks
> A ir s usp .: jac k mode > Off .
The vehicle jack mode * switches off automati­
ca lly at speeds above 6 mph (10 km/h) .
.8, WARNING
-Always read and fo llow all WARNINGS and
i nformat ion
c::> A in Raising the vehicle on
page 278
and c::> poge 280.
•
•

276 What do I do n ow ?
After changing a wheel
A wheel change is no t complete without the
doing the following .
.. Always store the vehicle tool kit, the jack*
and the replaced tire in the luggage com­
partment ¢
page 134.
.. Check the tire pre ssur e on the spare wheel
immediately after mount ing it .
.,. As soon as possible, have the
tightening
torqu es
on all wheel bol ts checked with a
torq ue wrench. The correct tightening tor ­
que is 90 ft lb (120 Nm) .
.. Have the flat tire
replaced as soon as possi­
ble.
@ Tips
- If you notice t hat the wheel bolts are
corroded and difficult to t urn while
changing a t ire, they should be replaced
before you check the tighten ing torque.
- Drive at reduced speed unt il you have the
tightening torques checked .
- After changing a wheel, the tire pressure
i n a ll four tires must be checked/correct­
ed and the tire pressure mon itor ing indi­
cator must be stored in the MMI
¢ page 272 .
Decorative wheel covers
Applies to vehicles: with decorative wheel covers
T he decora tive wheel covers must be removed
first to access the wheel bolts .
Fig. 210 Cha nging a w hee l: Remov ing t he w heel cove r
Removing
.,. Inse rt the hook (prov ided with the veh icle
tool kit) in t he hole in the wheel hub cove r. ..
Pull off the
de cora tive wheel co ver
¢ fig . 210.
Wheels with wheel bolt caps
Applies to veh icles: w it h w heel bolts with caps
The caps must be removed first from the
wheel bolts before the bolts can be un­
screwed.
Fi g. 211 Cha ng ing a whee l: re m oving t he w hee l b o lt
caps
Removing
.. Push the plastic clip (provided with t he veh i­
cle tool k it) over the wheel bo lt cap until the
inner retainers on the clip align w ith the
edge of the cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
i=> fig . 211 .
Refitting
.. Place the caps over the whee l bolts and
push them back on.
The caps are to protect and keep the wheel bolts clean .

M N <( I.J "". rl I.O
"' rl
"' rl
Loosening and tightening the wheel
bolt s
The wheel bolts must be loosened before rais­
ing the vehicle.
Fig . 212 Changing a wheel: loosening the whee l bo lts
Loosening
.. Slide the wheel wrench onto the wheel bolt
as far as it wi ll go .
.. Take tight hold of the
end of the wrench
hand le and turn the whee l bolts
counter­
clockwise
about one single turn in the direc­
tion of arrow c:>
fig. 212.
Tightening
.. Slid e the wheel wrench onto the whee l bolt
as far as it will go.
.. Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clockwise
until it is seated.
A WARNING
- Do not use force or hurry when changing
a whee l -you can cause the vehicle to s lip
off the jack and cause serious personal
injuries.
- Do not loosen the wheel bolts more than
one turn
before you raise the vehicle with
the jack. -You risk an injury.
(D Tips
-Never use the hexagonal socket in the
handle of the screwdriver to loosen or
tighten the wheel bolts.
-If a wheel bolt is very tight, you may find
it easier to loos en by carefully pushing
down on the end of the wheel bolt
wrench with
one foot only . As you do so,
What do I do now? 27 7
hold on to the car to keep your balance
and take care not to slip.
Raising the vehicle
The vehicle must be lifted with the jack first
before the wheel can be removed.
Fig . 213 Sill panels : marking s
Fig. 214 Sill: position ing the vehicle jack
.. Activate the vehicle jack mode* in the MMI:
!CARI function button> (Car)* systems con­
trol button>
Servicing & checks > Air susp .:
jack mode > On .
.,. Engage the parking brake to prevent your
veh icle from rolling unintentionally.
.,. Move the
selector lever to position P .
.. Find the marking (imprint) on the sill tha t is
nearest the whee l that will be changed
r=>fig. 213. Behind the marking, there is a
lifting point on the sill for the veh icle jack .
.. Veh icles with a sill: remove the cover from
the sill before lift ing the veh icle with a vehi­
cle jack
c:>page 278 .
.,. Turn the vehicle jack located under the lift­
ing point on the sill to raise the jack unti l its
arm @c:>
fig. 214 is located under the des­
ignated plastic mount c:> &, c:>(D .
.. Align the jack so that its arm@c:>
fig. 214
engages in the designated lifting point in
the door sill and the movable base@ lies
~

278 What do I do now?
flat on the ground. The base @ must be ver­
tical under the lifting point @.
• Wind the jack up further until the flat tire
comes
off the ground <=>,& .
Position the vehicle jack
only under the desig­
nated lifting points on the sill~
fig. 213.
There is exactly one location for each wheel.
The jack must not be positioned at any other
location <=> .&. <=>CD .
An
unstable surface under the jack can cause
the vehicle to slip
off the jack. Always provide
a firm base for the jack on the ground. If nec­
essary place a sturdy board or similar support
under the jack. On
hard, slippery surfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping~,&. .
.&, WARNING
-You or your passengers could be injured
while changing a wheel if you do not fol­ low these safety precautions:
- Position the vehicle jack only at the
designated lifting points and align the
jack. Otherwise, the vehicle jack could
slip and cause an injury if it does not
have sufficient hold on the vehicle.
-A soft or unstable surface under the
jack may cause the vehicle to slip
off
the jack. Always provide a firm base for
the jack on the ground.
If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack. -
Changes in temperature or load can af­
fect the height of the vehicle.
(D Note
Do not lift the vehicle by the sill. Position
the vehicle jack only at the designated lift­ ing points on the sill. Otherwise, your vehi­
cle will be damaged .
(D Tips
The vehicle jack mode* switches off auto­
matically at speeds above 6 mph (10 km/
h).
Removing and installing the s ill cover
Applies to vehicles: wit h sill
Fig. 215 Sill: removing the cover
,.. Pull the cover down to remove it¢ fig. 215.
• To install the cover again, insert it into the
retainers and then swing it upward until it
clicks into place. The cover must be flush
with the sill.
@ Tips
Some models may also have a cover for the
rear vehicle lift point.