service AUDI A7 2017 Owner´s Manual

co
co
.... N
" N .... 0
00
<.,;) 'SI"
Tire mobility kit
Preparation
Applies to: ve hicles with tire mobility ki t
~ Read and follow the important safety precau­
tions
c:::> page 240, General information.
~ Select the P selector leve r pos ition.
~ Check if a repair with the tire mobility kit is pos­
sible
c:::> page 241 .
Using the tire mobility kit
Appl ies to: ve hicles with tire mobili ty kit
Fig . 198 Tire: tire damage that canno t be repa ired
The ti re repa ir is only mea nt for temporary use .
Change the spare tire as soon as possib le
c:::> &. .
If the tire is pierced by an object such as a nail,
do not remove the object from the tire.
The tire repa ir set is able to be used at tempera­
tures as low as -4 °F ( -20 °C) .
The tire mobility kit ma y not be u sed:
- if the tire has cuts or punctures that are larger
than 0.16 in (4 mm)
(D c:::> fig. 198.
-If the rim is damaged @.
- if you drove with very low tire pressure or with-
out air in the tire @.
See an au thorized Aud i dealer or a utho rized Aud i
Service Facility for assistance in these situations.
A WARNING
- Please note that the tire mobility kit cannot
be used in a ll situations, and that it may on­
ly be used temporari ly.
- The tire sealant must not come in contact
with sk in, eyes, or clothes.
Em ergen cy a ssis tanc e
-If tire sealant gets in your eyes or on yo ur
skin, tho roughly rinse the affected area im­
mediately with clean water.
- Do not inha le the fumes.
- If you swa llow any of the tire sea lant, thor-
ough ly rinse your mo uth immediate ly and
drink a lot of water. Do not induce vomiting.
Seek med ical attention immed iate ly.
- Change yo ur clothes immediately if they get
tire sealant on them.
- If an a llergic reaction occurs, seek immedi­
ate med ica l attent ion.
- Keep the t ire sealant away from chi ldren.
- I n vehicles with a tire press ure monitor ing
system, using tire sealant can results in an
incorrect display or a system malfunction. Drive carefully to the nearest authorized
Aud i dealer o r authorized Audi Serv ice Facili­
ty.
(D Tips
- If sea lant leaks, allow it to dry in place . You
can then peel it off like a st icker.
- Note the expi ration date on the sea lant bot­
tle. Rep lace the t ire sealant at an author­
ized Audi dea ler or a uthorized Aud i Serv ice
Facility.
- Radio recept ion can be interrupted when
operating the compressor*.
- Obey all laws .
241

Emergency assistance
Repairing tires
Applies to: vehicles w ith tire mob ility k it
Fig. 199 Components of the tire mobility kit
F ig. 200 Tire mobility k it connecti on
Requirement: the tire mobility kit must be laid
out and ready for use
o page 240.
Installing the tire mobility kit
.. Open the cover @on the compressor
¢fig. 199 .
.. Remove the connector@) and pressure hose®
with pressure gauge from the housing.
• Install the compressor pressure hose ® onto
the f lange @ on the tire sea lant bottle
(D .
.. Insert the sealant bottle with the flange at the
bottom into the opening @ on the compressor
cover.
.. Remove the valve cap from the fau lty tire.
.. Install the filler hose@) on the valve
0
ofig. 200 .
.. Connect the plug @¢ fig. 199 to a socket in
the vehicle.
.. Switch the ignition on.
Inflating a tire
.. Move the switch @ o fig. 200 on the compres­
sor into position
I.
242
.. Inflate the tire between 29 PSI and 36 PSI (2 .0
and 2.5 bar) and read the tire pressure on the
gauge .
.. If this tire pressure is not reached, remove the
filler hose. Drive slowly approximately 10 m
forward or in reverse so that the sealant can be
distr ibuted in the t ire. Pump up the tir e again
¢ _&. .
.&_ WARNING
-Read and follow the manufacturer's safety
precaut ions on the compressor and in the
instructions on the bottle of sea lant .
- If a tire pressure of 29 psi (2.0 bar) cannot
be reached after inflating for six minutes,
then the tire is too severely damaged. Do
not continue driving.
- If the tire cannot be repa ired with the tire
sealant, see an authorized Audi dealer or au­
thorized Audi Service Facility for assistance.
(D Tips
Do not operate the compressor for more than
six minutes continuously, or it can overheat.
Once the compressor has cooled, you can con­
tinue to use it.
Completing
App lies to : vehicles wit h tire mob ility kit
.. Adhere the sticker that says "max. 50 mph"
(80 km/h) that is provided with the tire mob ili­
ty kit within the driver's field of vision.
.. Stop the vehicle after driv ing for about 10 mi­
nutes and check the tir e pressure.
.. If the tire press ure is lower than 19 PSI (1.3
bar), then the tire is too severely damaged. Do
not continue driving .
.&_ WARNING
Pay attention to the following after repairing
the tire:
- Do not drive faster than 50 mph (80 km/h).
- Avoid hard acceleration, braking sharply,
and fast cornering .
- The vehicle may become more difficult to
control.

co
co
.... N
" N .... 0
00
\.J ' -If the tire is too severely damaged, see an
authorized Aud i dealer or authorized Audi
Service Facility for assistance.
@ For the sake of the environment
You can give the used tire sealant bottle to an
authorized Audi dealer or authorized A udi
Service Facility for disposal.
@ Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop c::> &.,.
.. All passengers should leave the car and move
to a safe location (for instance, beh ind the
guardrai l) ¢ ,&. .
.. Engage the
parking brake to prevent your vehi­
cle from rolling unintentionally ¢,&. .
.. Move
selector lever to position P ¢ ,&. .
.. If you are towing a trailer, unhitch the trailer
from your vehicle .
.. Take the
jack and the spare tire* out of the lug­
gage compartment ¢
page 240.
.8, WARNING
You or your passengers could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
Emergency assistance
- To help prevent the vehicle from moving
suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­
ing changed . When one front wheel is lifted
off the ground, placing the Automatic
Transmission in P (Park) wi ll
not prevent the
veh icle from moving.
- Before you change a wheel, be sure the
ground is leve l and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
pa rtment
¢page 135.
(D Tips
Before changing the wheel, you must activate
the jacking mode, so that the automatic con­
trols for the Adaptive Air Suspension* do not
make it more difficult to lift the vehicle with
the jack ¢
page 245 .
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Activate the vehicle jack mode*¢ page 245.
2. Remove the decorative wheel cover* or the
wheel bolt caps*. For more details see also
¢ page 244, Decorative wheel covers or
¢ page 244, Wheels with wheel bolt caps .
3. Loosen the wheel bolts ¢page 245.
4. Locate the proper mounting point for the
jack and align the jack below that point
¢page 245.
5. Raise the car with the jack¢ page 245 .
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 247.
7. Tighten all whee l bolts lightly.
8.
Lower the vehicle with the jack.
9. Use the wheel bolt wrench and
firmly tighten
all wheel bolts
c::>page 245.
10. Replace the decorative wheel cover* or the
wheel bolt caps*.
11. Deactivate the vehicle jack mode* in the
MMI:
I CARI funct ion button> (C ar )* systems .,.
243

Emergency assistance
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare t ire with a tread pattern in­
tended for use in a specific direction, please note
the following:
- The direction of rotation is marked by an arrow
on the side of the tire.
- If the spare tire has to be installed in the incor­
rect direction, use the spare tire only tempora­
rily since the tire will not be able to achieve its
optimum performance characteristics with re­
gard to aquaplaning, noise and wear.
- We recommend that you pay particular atten­
tion to this fact during wet weather and that
you adjust your speed to match road condi­
tions.
- Replace the flat tire with a new one and have it
installed on your vehicle as soon as possible to
restore the handling advantages of a unidirec­
tional tire.
Notes on wheel changing
Please read the information q page 218, New
tires or wheels
if you are going to use a spare tire
which is different from the tires on your vehicle.
After you change a tire:
- Check the tire pressure on the spare tire im­
mediately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb
(120 Nm).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire ,
they should be replaced before you check the
tightening torque.
248
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble. Remount the wheel cover.
Until then , drive with extra care and at reduced
speeds.
~ WARNING
- If you are going to equip yo ur vehicle with
tires or rims which differ from those which
were factory installed, then be sure to read
the information
q page 218, New tires or
wheels.
- Always make sure the damaged wheel or
even a flat tire and the jack and tool kit are
properly secured in the luggage compart­
ment and are not loose in the passenger
compartment.
- In an accident or sudden maneuver they
could fly forward, injuring anyone in the ve­
hicle.
- Always stor e damaged wheel, jack and tools
secure ly in the luggage compartment. Oth­
erwise, in an accident or sudden maneuver
they could fly forward, causing injury to pas­
sengers in the vehicle.
Spare tire
Space-saving spare tire
App lies to: vehicles wit h spare tire
Fig. 209 Luggage compartment: space -saving spare t ire
The spare tire is intended for short-term use on-
-
ly. Have the damaged tire checked and, if neces­
sary, replaced by an authorized Audi dealer or au­
thorized Audi Service Facility as soon as possible . .,..

Fuses
Fuses
Replacing fuses
A fuse that has blown will have metal strips that have burned through.
F ig . 21 0 Driver 's side cockpit: cove r
The fuses are located on front left and r ight of
t he cockpit and behind the trim on the rig ht s ide
of the luggage compartmen t.
"' Switch the ignition and all e lectr ica l equipment
off.
"' Che ck the following table to see which fuse be­
l o ngs to the equipment.
... Remove the correspond ing cover or remove the
right side trim panel in the l uggage compart­
ment
¢ poge 195 .
... Remove the colored plastic clip from the fuse
panel, if necessary
¢page 251, fig. 211. You
can d ispose of the p lastic clip .
... Remove the clamp from the rea r side of the
cove r
¢fig. 210 .
... Remove the fuse usi ng the clamp.
"' Replace t he blow n fu se only wi th an identical
new one.
"' Install the cover.
Fuse color identification
Color Current rating
in amp s
Black 1
Purp le 3
L ight brown 5
B rown 7.5
Red 10
B lue 15
250
Color Current rating
in amps
Yellow 20
Wh ite or transpa rent 25
Green 30
O range 4 0
A WARNING
Do not repair fuses and neve r replace a blown
f u se with one that has a higher amp rat ing.
This can cause damage to the e lectr ica l sys­
tem and a fire.
(D Note
If a new fuse burns out again shortly after you
h ave insta lled it, have the e lectrical system
checked as soon as possible by an authorized
Audi dealer or authorized Aud i Service Fac ili­
ty.
(D Tips
- The following table does not list fuse loca­
t ions that are not used .
- Some of the equipment listed in the fo llow­
ing tables applies on ly to certain model ver­
sions or certa in optional equipment .

Emergency situations
Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
(D Note
Vehicles with an automat ic transmission can­
not be started by pushi ng or towing.
Starting with jumper
cables
If necessary, the engine con be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because of a dis ­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of suffic iently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use on ly jumper cables with
insulated term inal
clamps which are distinct ly marked :
plus(+ ) cable in most cases co lored red
minus (-) cable
in most cases colored black .
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for safe hand Ling of your veh icle's batte ry .
- Always shield your eyes and avo id leaning
over the battery whenever possible.
- A dead battery can freeze at temperatures
around 32 °F (0 °C). If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables.
If you do not, this in-
254
creases the risk of an explosion and chemi­
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author­
ized Audi Service Fac ility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immed iately.
- Improper use of a booster battery to start a
veh icle may cause an explosion .
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batter ies .
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-volt rat ing. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batter ies of different voltage or substantial­
ly different "Ah" rating may cause an exp lo­
sion and persona l injury.
- Never cha rge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never cha rge o r use a battery that has been
frozen . The battery case may have be weak­
ened.
- Use of batter ies of different voltage or sub­
stantially diff erent capacity (Ah) rating may
cause an explosion and injury . The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
r=:> poge 199.
([) Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive electronic components, such as control
units, relays, radio, etc.
- Th ere must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) terminals are connected .

@ Tips
The discharged battery must be properly con­
nected to the vehicle's electrical system .
When jump starting or charg ing the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negative ground cable to the negative ground
post of the battery manager control unit.
Use of jumper cables
Make sure to connect the jumper cable clamps in
exactly the order described below!
Fig. 214 Engine compartment: connectors fo r ju mp start
cables and charger

® @
Fig. 215 Jump starting with the battery of another vehicle:
@-booste r battery, @-discharged veh icle batte ry
The procedure described below for connecting
jumper cables is intended to provide a jump start
for your vehicle .
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever of
~ automatic transmission to N (Neutral) or P ....
~ (Park) and set parking brake . N .... 0
00
<.,;) 'SI"
Emergency situations
Connect POSITIVE(+) to POSITIVE (+) (red)
.. Open the red cover on the pos itive terminal
qfig. 214.
1. Connect one end of the red posit ive cab le on
the jump start bolt~
fig. 215 (D (bolt under
the red cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi- nal@ of the booster battery @.
Connect NEGATIVE (-) to NEGATIVE (-)
(black)
3. Connect one end of the black negative cable
to the negative terminal ® of the booster
battery @.
4. Connect the other end to the jump start pin
@ (bolts with hex head bolt= "negat ive'') of
the vehicle to be started @.
Starting the engine
.. Start the engine of the vehicle with the booster
battery @. Run the eng ine at a moderate
speed .
.. Start engine w ith discharged vehicle battery@
in the usual manner .
.. If the engine fails to start, do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With engine running, remove jumper cables
from both vehicles in the exact
reverse order .
.. Close the red cover on the positive terminal.
The battery is vented to the outside to prevent gases from entering the vehicle interior . Make
sure that the jumper clamps are well connected
with their metal parts in full contact with the battery terminals .
_&. WARNING
To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service.
- Jumper cables must be long enough so that
the vehicles do not touch .
- When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment. ..,.
255

co
co
.... N
" N .... 0
00
\.J ' Technical dat a
RS 7 Sportback 4.0, 8 cylinder
Maximum output SAE net hp@rpnn 560@ 5700 -6600
Maximum torque SAE net lb
-ft@ rpm
516@ 1750 -5500
Displacement CID (cm
3
) 243 .7 (3993)
Engine oil with f ilter change
1>
Fuel Pr emium un lead ed (91 A KI), c> page 191, Fuel supply
RS 7 Sportback performance 4.0 , 8 cylinder
Maximum output SAE net hp@ rpnn 605@ 6100 -6800
Maximum torque SAE net lb
-ft@ rpm 517@ 1750 -6000
Maximum torque SAE net with over lb-ft@ rpm 553 @ 2500 -5500
boost
Displacement CID (cm
3
) 243.7 (3993)
Engine oil with filter change
1l
Fuel
P remium unle aded (91 A KI) , c> page 191, Fuel supply
Diesel engines
A7 3.0 TOI, 6 cylinder
Maximum output SAE net hp@ rpnn
Ma ximum torq ue SAE net lb-ft@ rpm
Displacement CID (cm
3
)
Engine oil with f ilter change1>
Fuel ULSD No . 2 , c> page 192, Diesel fuel
ll For specific engine oil capacities, please see
the most current information for the USA at
http ://www.aud iusa.com/help/maintenance or
for Canada at http://www.audi.ca/ca/brand/ en/
your _aud i/ aud i_services_a nd/Care_and_M a i nte­
na nce/ schedu le.html or call 800-822-2834. 239@ 3500
-3750
428@ 1750 -2250
181 (2967)
263

Consumer information
Consumer information
Warranty coverages
Your Audi is covered by the following warran­
ties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the poss ibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a considerably lower octane rat­
ing . Improper fuel may cause engine damage;
- service may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igation systems for veh icles built for the
U.S .A . and Canada will not necessarily work in
Europe, and may not work in other countries
outside North America.
264
(D Note
Audi cannot be responsib le for mechanical
damage that could result from inadequate
f u el, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introd uction . Service manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at :
www.audi.techliterature .com
Maintenance
General '
Your vehicle has been designed to help keep
maintenance requirements to a min imum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintena nce consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam ­
ple at extremely low outside temperatures, in
very dusty regions, etc., some se rvice work
should be performed between the intervals speci­
fied. This applies particularly to:
- oil changes, and
- cleaning or replac ing the a ir filter .
@ For the sake of the environment
By regularly maintaining your vehicle, you
help make sure that emission standards are
maintained, thus min imizing adverse effects
on the environment.
Important considerations for you and your
vehicle
The increas ing use of elect ronics, soph istica ted
fuel injection and emission control systems, and
the genera lly increasing technica l complexity of
today's automobiles, have stead ily reduced the ..,_

Consumer inf orm ation
@ For the sake of the env ironment
- Changing the engine settings wi ll adversely
affect emission levels. Th is is detrimental to
the environment and increases fuel con­
sumption.
- A lways observe environmental regu lations
when disposing of old engine o il, used brake
fl ui d, d irty engine coolant, spent batteries
or worn out tires.
- Undeployed airbag modules and pretension­
ers mig ht be classified as Perchlorate Mate­
rial -special handl ing may apply, see
www.dtsc .ca.gov/hazardouswaste/perchlo­
r ate. When the vehicle or parts of the re­
straint system including airbag modu les
safety be lts wi th pretensioners are scrap­
ped, all applicab le laws and regulations
must be observed. Your authorized Audi
dealer is familiar with these requirements
and we recommend that you have your deal­ er perform this service for you.
Accessories and technical changes
Additional accessories and parts replacement
Always consult an authorized Audi dealer before
purchasing accessories.
Your vehicle incorporates the latest safety design
features ensuring a high standard of active and passive safety.
This safety could be comp romised by non-ap­
proved changes to the vehicle . For this reason, if
parts have to be replaced, please observe the fo l­
lowing points when insta lling addit ional accesso­
ries:
Approved Audi accessories and genuine Audi parts are available from author ized Audi dealers.
These dealers also have the necessary faci lities,
too ls and trained specialists to install the parts
and accessories properly.
266
A WARNING
-
Using the wrong spare parts or using non-ap-
proved accessories can cause damage to the
vehicle and serious personal injury.
- Use only accessories expressly approved by
Aud i and genuine Audi spare parts
- These parts and accessor ies have been spe­
cially designed to be used on your vehicle.
- Do not use license plate brackets in the
front area that are d ifferent from the one
installed at the factory, or add additional li­
cense plate brackets.
- Never install accessor ies such as telephone
cradles or beverage holders on airbag covers
or w it hi n the airbag deployment zones. Do­
ing so will i ncrease t he risk of injury if a ir­
bags are triggered in an accident!
- Before you check anything in the eng ine
compa rtment, always read and heed all
WARN INGS ¢page 199.
(D Note
-If items other than genu ine A udi spa re
parts, add-on equipment and accessory
i t ems are used or if repair wor k is not per­
formed according to specified me thods, this
can resul t in severe damage to your vehi ­
cle's eng ine and body (such as corrosion)
and adve rsely affect your vehicle's warranty.
- If emergency repai rs must be per formed
elsewhere, have the vehicle examined by an
authorized Audi dealer as soon as possib le .
- The manufacturer cannot be held liable for
damage which occurs d ue to failure to com­
ply with these stipulations.
Technical Modifications
Our guidelines must be complied with when tech­
nical modifications are made .
A lways consu lt an authorized Audi dea ler
before
start ing work on any modifications .
This will help ensure tha t vehi cle fu nction, per-
fo rmance and s afety are not impaired¢ &,.
ll-