oil AUDI Q5 2013 User Guide

Fa u lts in th e brake sy stem
If you should notice a sudden increase in
brake peda l travel, then one of the two brake
circuits may have failed~.&. .
Low brak e flu id level
Malfunct ions can occur in the brake system if
the brake fl uid leve l is too low . T he b rake fluid
l eve l is monito red electronically .
Brake booster
The brake booster increases the pressure that
you generate w ith the brake pedal.
It only op­
e rates while the eng ine is running or with the
i gnit ion sw itched on (hybr id dr ive*) ~.&, .
Brake lining wear statu s
Brake lining wear may be checked by visual in ­
spection of the condition of the brake pads
through the openings in the whee l. If neces­
sa ry, the wheel may be removed for this in­
spection
~ page 2 74, Changing a wheel.
.&_ WARNING
=
- You should perform braking maneuvers
for the purpose of clean ing the brake
system on ly if road conditions permit.
Other road users must not be put at risk -
you may cause an acc ident!
- Before descending a steep grade, reduce
speed and shift transmiss ion into a lower
gear or lower driving range . Do not ride
the brakes or hold the pedal down too long or too often . This could cause the
brakes to get hot and dimin ish b raking
efficiency .
- Do not "ride the brakes" by resting your
foot on the pedal when you do not intend
to brake . Th is may cause the b rakes to
overheat, premat ure wear and increased
stopping distance .
- Under certain climat ic and operating
condit ions such as passing through wa­
ter , driving in heavy rain or after wash ing
the vehicle, the effectiveness of the brakes can be reduced. In winter, ice can
accumulate on the brake pads, linings,
discs and drums . Carefully apply brakes
Int ellig ent technolog y 201
for a test. Brakes will dry and ice coat­
ings w ill be cleaned off after a few care­
ful brake applicat ions.
- Driving for an extended period of time on
salt-covered roads without using your
brakes can also affect braking efficiency.
Clean off accumulated salt coating from
brake discs and pads with a few careful
brake applications.
- If you damage the front spoiler, or if you install a different spoiler, be sure the air
f low to the front brakes is not obst ruct­
ed. Otherw ise the brake system could
overhea t reducing the effectiveness of
the entire brake system .
- Failure of one brake circuit will impair
the braking capability resulting in an in­
creased stopping distance . Avoid driving
the vehicle and have it towed to the near­
est a uthori zed Audi dea ler or qualified
workshop.
- Never let the vehicle roll to a stop with
the engine shut off .
- If the brake booster is not working, for
examp le when towing your vehicle, or
because the brake booster has somehow
been damaged, the brake pedal must be
pressed considerably harder to make up
for the lack of booster assistance .
Electromechanical
power assist, Dynamic
steering
The electromechanical power assist helps the
driver when s teering.
Power ste ering adapts electronically based on
the vehicle speed.
Indicator lights an d m ess age s
• Steeri ng defe ctive ! D o n ot dr ive vehi cle!
If this indicator light turns on and stays on
and this message appears, the power steer ing
may have failed .
Stop the vehicle in a safe location as soon as poss ible . Do
no t continue driving . See your ..,.
•
•

206 Driving and en vir onm ent
Catalytic converter
It is very important that your emission con­
trol system (catalytic converter) is function­
ing properly to ensure that your vehicle is run­
ning in an environmentally sound manner .
• Always use lead-free gasoline¢ page 228,
Fuel supply.
• Never run the tank down all the way to
empty .
• Never put too much motor oil in your en-
gine ¢
page 238, Adding engine oil~-
., Never try to push- or tow -start your veh icle.
The catalytic converter is an eff ic ient "clean­
up" device built into the exhaust system of
the vehicle. The catalytic converter burns many of the pollutants in the exhaust gas be­
fore they are released into the atmosphere.
The exclusive use of unleaded fuel is critically
important for the life of the cata lytic conve rt­
e r and proper functioning of the engine.
& WARNING
-
- Do not park o r operate the vehicle in
areas where the hot exhaust system may
come in contact with dry grass, brush,
fuel spill or other material which can cause a fire.
- Do not apply additional undercoating or
rustproofing on or near the exhaust
man ifold, exhaust p ipes, catalytic con­
verter or heat shields . During driving, the
substance used for undercoating could
overheat and cause a fire .
@ Note
-Be aware that just one tank filling with
leaded fuel will already seriously de­
grade the performance of the catalytic
conve rter .
- Do not exceed the correct engine oil level
¢ page 238.
-Do not drive until the fuel tank becomes
completely empty. The eng ine could mis­
fire . U nburned f uel could a lso get into the exhaust system and this co
uld cause
the cata lytic converter to overheat .
- Do not turn off the ignition while the ve ­
hicle is moving.
- Do not continue to ope rate your veh icle
under these conditions, as otherwise fuel
can reach the catalytic converter. This
cou ld result in overheating of the con­
verter, requir ing its replacement.
- To assure efficient operation of the Emis ­
sion Control System:
- H ave your vehicle maintained properly
and in accordance w it h the service rec­
ommendat ions in your Warranty &
M ain tenance book let.
- L ack of prope r maintenance as we ll as
improper use of the vehi cle will impair
the function of the em iss ion contro l
system and could lead to damage .
@ For the sake of the environment
Even when the Emiss ion Control System is
operat ing proper ly, the exha ust gas can
have a sul fur -li ke exhaust gas smell under
some operating states . This depends on
the sulfur content of the fuel being used .
Using a different brand of fue l may help,
or f il li ng the tank with lead-free super
grade gasoline .
Avoid damaging the
vehicle
When you are d rivi ng on poor roads, or over
c u rbs, steep ramps, etc., ma ke certai n that
low- ly ing parts s uch as spoilers and exha ust
system parts do not bottom o ut and get dam ­
aged.
T his is espe cially true for ve hicles with low­
s lung chassis (spor ts chassis)* and fully load­
ed vehicles .

208 Driving and environment
would go unheeded. Extended idling also
produces heat, which could result in over­ heating or other damage to the vehicle or
other property .
Regular maintenance
A badly tuned engine unnecessarily wastes a
lot of fuel .
• Have your vehicle serviced at regular inter-
vals.
By having your vehicle regularly serviced by an
authorized Audi dealer helps to ensure that it
runs properly and economically. The condition
of your vehicle not only affects its safety and
ability to hold its value, it also affects
fuel
consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine
load and speed.
It is normal for the oil consumption of a new
engine to reach its lowest value after a certain mileage has been driven .
You must drive your vehicle about 3,000 miles (5,000 kilometers) before you can properly
assess oil consumption .
This also applies to fuel consumption and en­
gine output .
{Q) Note
-Have your vehicle maintained properly
and in accordance with the service rec­
ommendations in your Warranty
& Main­
tenance booklet. Lack of proper mainte­
nance as well as improper use of the ve­
hicle will impair the function of the
emission control system and could lead
to damage.
- Do not alter or remove any component of
the Emission Control System unless ap­
proved by the manufacturer.
- Do not alter or remove any device, such
as heat shields, switches, ignition wires,
valves, which are designed to protect
your vehicle's Emission Control System and
other important vehicle compo­
nents.
Fewer short trips
Fuel consumption will always be relatively
high on short trips.
• Try to avoid driving short distances with a
cold engine.
The engine and catalytic converter have to
reach their optimal
operating temperature to
reduce fuel consumption and noxious emis­
sions effectively.
Just after starting, a cold engine in a mid-size
car only achieves a fuel economy of 6-8 miles
per gallon (30-40 l/100 km). After about a
half a mile , fuel economy climbs to 12 mpg
(20 l/100 km). After about
2.5 miles (4 km),
the engine is at its proper operating tempera­
ture and fuel economy has reached a normal level. So you can see that you should avoid
short trips whenever possible .
T he
outside temperature is also critical in this
regard. Your car consumes more fuel in the
winter than in the summer .

Automatic car wash
The vehicle can be washed in almost any
modern automatic car wash .
The vehicle paint is so durable that the vehicle
can normally be washed without problems in
an automatic car wash. However, the effect on
the paint depends to a large extent on the de­
sig n of the fac ility, the filtering of the wash
water, the type of wash and care mater ial , etc.
If the paint has a dull appearance afte r go ing
through the car wash or is scratched, bring
this to the attention of the operator immedi­
ately. If necessary, use a different car wash.
Before going through a ca r wash, be s ure to
take the usual precautions such as closing the
windows and the roof . Factory installed an­
tennas m ust not be removed.
If you have installed additional accessor ies on
the vehicle -such as spoilers, roof rack, etc. -
it is best to ask the car was h operator if these
should be removed .
A WARNING
Please take note of the follow ing po ints
before going through an automatic car
wash with your vehicle, so that you can
avoid damage to your vehicle.
- Compare the track of your vehicle with
the distance between the gu ide rails of
the fac ility- there is a risk of damage to
the wheels and t ires.
- Compare the height and w idth of your
vehicle with the he ight and width of the
tunnel at the fac ility.
- Fold the exte rior mi rrors flat -there is a
r isk of damag ing the exte rior m irrors.
Power folding ex terior m irrors* must not
be folded in o r out by hand . Use the pow ­
er function !
- Do not a llow the wipe r blade to fall o nto
t he windsh ield after the vehicle is dried -
there is a r isk o f damag ing the pa int on
the hood .
- Always read and heed all WARN INGS and
other information ¢
page 216.
-
Cleaning and protec tion 217
Washing the vehicle by hand
A lot of water is needed when washing a vehi­
cle by hand .
.,. Before you start washing, make sure you
have read and u nderstood the WARNINGS
Q .&. in General information on page 216 .
.,. First soak all dried d irt unt il it is soft, then
r inse it off.
.,. As you clean your vehicle , start w it h the
roof and wor k your way down to the bottom,
using a sponge, a sponge g love or a clean
brush.
.,. Rinse the sponge o r the sponge g love often,
flushing it clean each time.
.,. Use specia l car shampoo only for
very per­
sistent d irt .
.,. Rinse the car thoroughly with water .
.,. Use a chamo is leather to gent ly w ipe the ex-
ter ior d ry.
Use a separate sponge for cleaning the
whee ls, door sills and othe r regions exposed
to road dirt . In this way, you w ill not scratch
the pa int w it h coarse par ticl es imbedded in
the sponge the next time you wash the ca r.
& WARNING ~ -
- Wash your vehicle only when the ignition
is switched off to red uce the risk of a
crash.
-A lways read and heed a ll WARNI NGS and
other information
~ page 216.
{(D Note
-Never try to remove dirt, mu d or dus t if
t he su rface o f the ve hicle is dry. Never
use a dry cloth or sponge, s ince this
co uld scratch your vehicle's paint or win­
dows.
- Never wash your car in bright s unlight .
Drops of water act as magnifying lenses
and may damage yo ur paint .
- When you wash your car in the winter: if
you rinse yo ur vehicle with a hose, be
careful not to aim the stream of water
directly at locks, or at door or hatch
openings - they can freeze shut . •
•

218 Clea ning and protec tio n
- Never use sp onges designed to remove
insects, or a ny kitchen scouring sponges
or similar products . They can dama ge
you r paint f inish.
- Never use a dry cloth or s ponge to clean
the headligh ts. On ly use wet clot hs or
sponges to prevent scratches.
It i s best
to use soapy water.
- You should rem ove debris (suc h as in ­
sects) from the headlight lenses on a
regular basis, fo r example when refuel­
i ng your vehicle. Never clean the head­
li ghts w ith a dry cloth or sponge. Use a
wet cloth or sponge.
It is best to use
soapy water.
@ For the sake of the environment
On ly wash the vehicle in facilit ies specially
designed for that pu rpose. This w ill reduce
t he risk of d irty water contami nated with
oil from en tering the sewer system. In
some areas, washing vehicles outside of
these facilities is prohibited .
Washing your vehicle with a power
washer
Cleaning the exterior of your car with a high­
pressure power washer is safe as long as you
observe a few simple rules.
.. Before us ing the power washe r, make sure
you have read and understood the WARN­
INGS¢
A in General information on
page 216 .
• Always follow the operating instructions for
the power washer .
• Make sure that the jet o n the spray hose
produces a "fan shaped sp ray ".
• Do
not ho ld the spray nozzle too close t o
soft materia ls.
Keep a d istance from soft mate rials such as
rubber hoses or insulat ing mater ial as well as
sensors and camera lenses .
When clea ning the veh icle w it h a power wash­
e r
always fo llow the operating instructions.
This applies particul arly to the operating pres­
sure and the spraying distance. Do not po int the spray di
rectly at the seals around the side
windows, around the doors, on the rear lid or
on the Panoram ic sliding sunroof* . Likewise,
do not po int it direct ly at tires, rubber hoses,
insulat ion material or sensors
¢ page 219.
Hold the spray nozz le at least 1.3 ft (0.4 m)
away from the vehicle.
Do not use a high-pressure power washer to
remove snow and ice .
Do not use a jet which sprays water in a direct
stream or one that has a rotating jet .
Water tempera ture sho uld no t exceed 140 ° F
(60 °().
_& WARNING
Neve r wash tires with a jet t hat sprays wa­
ter in a direct stream . Th is could cause in­
v is ible damage to the t ires and weaken
them, even if the spray is from a relative ly
l ong distance and for a short time. Dam­
aged and weakened tires can fail and cause
accidents and personal in ju ry .
(D Note
To avoid damaging you r vehicle, always
make sure that there is suffic ient d istance
between the spray head and soft materia ls
l ike rubber hoses, plast ic pa rts and sound­
deade ning mater ia ls as well as sensors
and camera lenses. Never a im the sp ray
head at the same point fo r a long time .
This also applies to cleaning headlights
and painted bumpers. Remembe r: the
closer the nozzle is to the surface of the
mater ia l, the greater the stress on the ma­
terial.

220 Cleaning and protec tio n
- do not clean the camera lenses and the
area around them with the pressure
washer.
- Never use warm or hot water to remove
snow or ice from the camera lens. T his
could cause the lens to crack.
- Never clean the camera lens with abra­
sive prod ucts .
Waxing and Polishing
Wa xing
A good wax coating protects the vehicle paint
to a large extent against the environmental
factors listed under
qpage 216, Washing and
even against slight scratches .
You can use a liquid car wax to protect your pa int as soon as one week after your veh icle
has been delivered.
Even if you regularly use a
w axi ng process in
automatic car washes, we recommend that
you manua lly app ly a coat of wax to give the
pa int extra protection, particularly if water no
longer beads on the clean paint .
Protect p lastic body parts with car wax in the
same way as the vehicle body.
During wa rm weather dead insects tend to
collect on the front bumper and on the for­
ward area of the hood . They are much easier
to remove from paint that is waxed
often.
P oli shing
Polish your vehicle on ly if the paint has lost its
shine and the g loss cannot be brought back
with wax .
I f the polish used does not contain preserva ­
tive compounds, the paint must be waxed af­
terwards .
_&. WARNING
Always read and heed a ll WARNINGS and
other information
9 page 216.
@ Note
Donotusecarwaxon -
matte o r anodized meta l trim
- rubber or rubber- like t rim.
Trim strips
Metal trim needs special care.
For environmental reasons, Audi fabricates
the bright trim strips and trim p ieces from
pure chromium-free aluminum .
Dirt and marks on the trim strips should be
removed with a
pH-b alan ced cleaning agent
(do not use a chrome cleaner) . Authorized
Audi dealers carry cleaning products which have been tested for use on you r vehicle and
are not ha rmfu l to the environment.
To avoid corrosion on the exter ior trim strips ,
only a pH-ba lanced solution shou ld be used
for the windsh ield washer.
_&. WARNING
A lways read and heed all WARNINGS and
other information
q page 216.
Plastic and vinyl
Plastic needs special care.
Use a clean, damp cloth or sponge to remove
dust and light surface dirt . For othe r soil, use
a lukewa rm all-pu rpose cleaning solution or a
mild saddle soap for v inyl tr im . Remove wate r
spots and traces of soap wi th a clean, damp
cloth or sponge. Use a clean, soft cloth to rub
dry.
G rease , tar or oil sta ins can be removed with a
cle an cloth or sponge soaked wi th a ll-purpose
cleaner or with a solvent designed especia lly
to clean vinyl.
O ccas ional ly app ly a colorless v inyl or leather
preservative to re tain the materia l's luster
and pliability.
_&. WARNING
A lways read and heed all WAR NINGS and
other information
q page 216.

Aluminum trim
Use only neutral -pH products to remove spots
and depos its from alum in um s urfaces.
Chrome care products and alkaline cleaners
will attack aluminum surfaces and can dam­
age them over time.
A WARNING
Always read and heed all WARNINGS and other information ¢
page 216.
Touch-up paint
Minor paint damages should be touched up
immediately.
"" Use either a touch-up pa int stick or spray
paint to cover minor scratches and nicks.
Your author ized A udi dealer has touch-up
pa int for minor sc ra tches and stone ch ips.
Scratches shou ld be touched up soon after
they occur to prevent corrosion .
If a spot starts to rust, howeve r, a simple
t ouch- up job w ill not be enough. The affected
sur face must be sanded smooth and coated
with an anti-r ust primer before the painted
finish can be restored.
The number for the origina l vehicle paint can
be found on the vehicle identi ficat ion labe l
¢page 290.
A WARNING
Always read and heed a ll WARNINGS and
other information
¢ page 216.
Windows
Clear vision to all sides .
Clea n all windows regularly to remove road
fi lm and ca r wash wax b uild up.
"" Remove snow from windows using a brush .
"" Use a plast ic ice scraper to remove ice from
windows and mirro rs.
"" Remove other res idue on the windows with
a sp ray -on glass cleaner.
Cleaning and protec tion
"" Wipe the windows dry with a clean piece of
cloth or kitchen paper towe l.
T he best way to remove snow from windows
and mirrors is to use a brush . Use a non-abra ­
sive
plastic ice scrape r -better sti ll, a spray
deicer - to remove
ice from windows and mir­
rors.
T he windows must not be cleaned with insect
remover or wax since these can interfere with
the function of the windshie ld w iper blades
(chatter) .
Oil, grease, o r si licone residue can be removed
with
gla ss cleane r or silicone remove r. How­
ever, wax residue requires the use of a specia l­
ly formulated so lvent. Please contact your au­
thori zed Audi dealer for advice on safe prod­
ucts for wax removal.
Windows should also be cleaned on the inside
at regu lar intervals .
Never dry windows wit h the same chamo is
that you use to dry painted surfaces . Wax resi­
due o n the chamois can impair vision through
the windows .
A WARNING
-Always read and heed all WARNINGS and
other information ¢
page 216.
-The windsh ield must not be treated with
water-repellent materials. They can in­
crease glare under poor v is ibility condi­
tions such as wetness, darkness, or when the sun is low on the hor izon. In addi­
tion, they can ca use the w indshie ld w ip­
ers to ch atter.
@ Note
- Never use warm o r hot wate r to remove
snow and ice from w indows and mirro rs.
T his could cause the glass to crack.
- T o prevent damage to the wires of the
rear defogger, do not place any adhesive
st ic kers on the ins ide of the rear w indow
over the wires.
221
•
•

224 Cleaning and protection
Cl ean ing s ta ins
Stains caused by beverages (e.g. coffee, fruit
juice, etc.) can be treated with a mild deter­
gent solution. App ly the detergent so lution
with a sponge. In the case of stubborn stains,
a detergent paste can be applied directly to
the stain and worked into the fabric. After­
wards, use copious amounts of clean water to remove the remaining detergent . Apply the
water with a damp cloth or sponge and pat
the fabric d ry w ith an absorbent, dry cloth.
Stains from chocolate or makeup should have
detergent paste rubbed into them. After ­
wards, remove the soap w ith water (damp
sponge) .
Alcohol can be used to treat stains from
grease, oil, lipstick or a ballpo int pen. Melted
grease or dye must be patted off using ab­
sorbent material.
It may be necessary to re­
treat the a reas with dete rgent paste and wa­
ter.
In the case of genera l so iling of the uphols­
tery and cover mater ial, we recommend h iring
a specialist that has the eq uipment to clean
the sea t covers and other fabric surfaces by
shampooing and spray extraction.
& WARNING
Always read and heed a ll WARNINGS and
the information
¢ page 216.
(D Tips
Open Ve lcro fasteners on your cloth ing can
damage the seat cover. P lease make sure
that Ve lcro fasteners are closed .
Plastic parts and instrument panel
Always use a clean cloth moistened in clear
water to clean these areas. For pers istent dirt
use an Audi approved
solv ent-fr ee plastic
cleaner/protectant.
& WARNING
Solvents can change the properties of
some p lastics and make it harder fo r the
a ir bag to deploy.
-
- Never clean the instrument panel or the
surface of airbag modu les w ith cleaning
products that conta in solvents.
- Products containing solvents will make
the surface of this pa rt porous.
- Ser ious injuries can resu lt if p lastic parts
come loose when the a irbag is deployed .
- Always read and heed all WARNINGS and
other information ¢
page 216.
(D Note
Cleaning agents conta ining so lvents wi ll
attack the material and can change the
way it behaves.
Natural leather
Applies to vehicles: with natural leather
Audi makes great efforts to maintain the
properties, natural look and feel of interior
leather.
General
We offer many different types of leather on
o u r vehicles. Most are d ifferent types of nappa
l eather, which has a smooth surface and
comes in various colors.
The intensity of the co lor determines the visu­
al characteristics and appea rance. If the sur­
face of the leather has a typica l natural look,
then the leather is a nappa leather that has
been left in a relative ly natural condit ion. This
leather offers particularly good comfort and
breathes we ll. Fine veins, closed grains, insect
bites, sk in fo lds, and subt le variations in color
rema in v is ible. These charac ter istics demon­
strate that the mate rial is natura l.
Natural nappa leather is not covered by a co l­
o r finish.
It is therefo re more sensit ive to soil­
ing and wea r, which is someth ing you need to
consider if children, animals or other fac tors
mig ht prove to be particu larly hard on the
l eather . ..,

By contrast, leather types that are covered by
a co lored finish layer are more durable. This
has a posit ive effect on the leather's resist­
ance to wear and soiling in daily use. On the
other hand, the typical characterist ics of natu­
ral leather are barely or not apparent . Howev­
er, this does not mean that the leather itself
i s of infer ior quality.
C ar e and h and ling
Because of the exclusive nature of the types of
leather that Audi uses and the ir unique prop­
erties (such as sensitivity to o ils, grease, so il­
ing, etc.), you will need to be somewhat care­
fu l w ith these leathers, and a certain type of
care is required. For examp le, da rk clot hing
materia ls can d iscolor leather seats (especial­
l y i f such clothing is damp and was not dyed
correctly) . Dust and dirt particles in pores,
fo lds, and seams can have an abrasive effect
and can damage the leather surface as we ll as
weaken seams.
The leather sho uld be cleaned regularly as
needed. After having been used for a re lative ly
long time, your leather seats will acquire a
rich aged finish. This is a characteristic of nat­
ura l leather and a sign of true quality.
In order to maintain the va lue of this natura l
product over the life of your vehicle, you
should follow the recommendations below:
(D Note
- To keep your leather from bleaching out,
do not a llow it to be exposed to bright
sunlight for long periods of time. If you
have to leave the vehicle parked outside
for long periods, cover the leather to
protect it from d irect exposure to su n­
light.
- Sharp objects on clothing, such as zip­
pers, rivets or sharp pieces on be lts can
l eave pe rmanent scratches o r sc rape
mar ks on the surface of the lea ther.
{O) Tips
-After each time you clean the leathe r and
at regu la r i nte rva ls, use a leather prese r-
Cleaning and protec tion 225
vative c ream that contains UV -b locke rs
and that works into the leather. This
cream wi ll nour ish and mo isturize the
leather, helping it to breathe and stay
supple. It also helps to build up a protec­
t ive coating on the surface.
- Clean the leather every 2 - 3 months,
and clean any areas that get soiled.
- Remove fresh marks made by ballpo int
pens, ink, lipstick, shoe polish, etc. as
soon as poss ible.
- Preserve the color of the leather as need­
ed by us ing a specia l co lored leather care
cream to touch up areas of uneve n color .
Cleaning and caring for leather
upholstery and trim
Applies to vehicles: wi th natural leather
Natural leather requires special care and at­
tention .
Normal cleaning
.. Clean soiled areas with a slightly moistened
cotton or woolen cloth.
More stubborn dirt
.. More st ubborn dirt can be removed using a
cloth saturated with a mild soap solut ion
(2
tablespoons mild liquid soap).
.. Never allow the soap solution to saturate
the leather, and make certain that no water
soaks into the seams .
.. Wipe off the soap so lution with a soft, dry
cloth.
Cleaning spo ts
.. Remove fresh water-based spots (such as
coffee, tea, juices, blood) with an absorbent
cloth or pape r towel.
.. Remove fresh
grease or oil -based spots
(suc h as bu tte r, mayonnaise, chocolate) with
an absorben t cloth or paper towel, o r use
t he cleaner from the leather care kit if the
spot has not yet penetrated into t he surface
of the leathe r.
.. Use an oil/grease dissolving spray, if
oil /
grease spots ha ve dried on.
•
•

226 Cleaning and protec tio n
• Remove specific kinds of spots (ballpoint
pen, felt marker, fingernai l polish, water­
based paint, shoe polish, etc .) with a spot
remover specifically formulated for leather .
Leath er care
• Every ha lf year use an approved leather care
product (available from your authorized
Audi dealer) to care for the leather.
• Apply the product very sparing ly.
• Wipe it off with a damp cloth.
If you have any questions about cleaning and
caring for the leather in your vehicle, it is best
to contact your author ized Audi dealer, who
will be glad to help you and tell you about our
full range of leather care products, such as:
- Leather cleaning and care
kit
- Creams to care for colored leather
- Spot removers fo r ballpo int pens, shoe po l-
ish , etc.
- Oil/grease dissolving spray
- New and upcoming products.
_& WARNING
Always read and heed a ll WARNINGS and
other information
r::!v page 216.
(D Note
- Neve r use chemical solvents (e.g . lighter
fluid, turpentine), waxes, shoe polish or
s imilar products on the leather surfaces
i n you r A ud i.
- To avoid damage, have stubborn stains
r emoved by a commer cial cleani ng spe­
cia list .
Safety belts
Only well-maintained safety belts work relia­
bly when needed.
• Keep be lts clean .
• Fo r cl eaning, use a m ild soap and wate r sol­
u tio n. Let be lts dry thoro ughly and away
from direct sunlight .
• Do not a llow inertia reel safety be lts to re ­
tract before they are completely dry . •
Check the condition of your safety be lts
reg ­
ularly .
Heavi ly so iled s afety bel ts may not ret ract
proper ly .
A WARNING
Damaged safety belts can break in a crash .
- Anyth ing that might damage your sa fety
be lts could mean that you and your pas ­
sengers would not be adequate ly pro­
tected in an accident.
- Safety belt performance depends on cor­
rect insta llation. Never remove be lts
from the veh icle to clean them.
- Do not use chemical cleaning agents,
bleach or dyes. They have corrosive prop­
erties which weaken the webb ing.
- When cleaning you r safety be lts, inspect
them for damage. If you discover dam­
age, see your authorized Audi dealer .
- Always read and heed a ll WARNINGS and
other information
r::!v page 216.
Engine compartment
Be especially careful when cleaning the en­
gine compartment.
Alway s swit ch off th e ignition before cle an­
ing the engine
r::!v .&. .
Plenum panel
Remove leaves from the plenum panel in front
of the w indshield under the eng ine hood. This
preve nts the wa ter dr ain holes from becomi ng
blocked, and it prevents debris from entering
the ve hicle interior t hrough the heating and
ventilat ion ducts .
Corrosion protection
T he eng ine compartmen t and transmission
have been co rrosion-protected a t the f actory.
Good anti-corrosion treatment is very impor­
tant, particu larly in the w inte r.
If the vehicle
is frequently d riven on salt t rea ted roads, the
en tire engine compar tment and p lenum panel
shou ld be thoroughly cleaned at the end of
winter and retreated to prevent salt damage. ...