radio AUDI Q5 2013 User Guide

40 Opening and closing
Fold mirrors* -if you select On , the outside
mirrors will fold in automatically when you
press the
Iii button on the remote control key
c>page57.
Confirmation tone/Tone when locking -if you
se lect
On , a tone will sound when you lock the
vehicle .
Unlocking and locking the vehicle with
the remote control
Fig . 29 Remote co ntro l: fu nctio n buttons
Either the driver's door only or the entire vehi­
cle will unlock when the unlock button @ is
pressed once, depending on the settings in
the radio or MMI*
Central lock ing menu
c> page39.
.. Press button @(@ ) to unlock the vehicle
c>fig. 29.
.. Press button tfJ (@ ) to lock the vehicle c> .&.
in General description on page 39 .
.. Press the button c:5 (@ ) for at least one
second to open the rear lid .
.. Push the red
!PANIC I button( @) to activa te
the panic func tion. The horn sounds and the
tu rn s ignals flash. Push the red
I PANIC I but­
ton again to deactivate the panic function.
If the vehicle is unlocked and no door, the rear
lid or the hood is opened within 60 seconds,
the vehicle locks itself again automatically.
This feature prevents the vehicle from being
accidenta lly left unlocked over a long period
of time.
It depends on the settings in the radio or in
the MMI* whether the entire vehicle is un­
locked or only certain doors
¢ page 39.
On vehicles with Convenience key*, the selec­
tor lever must be in the P position, otherwise
the vehicle cannot be locked.
A WARNING
-Read and follow all WARNINGS c> .&. in
General description on page 39.
(D Tips
- In order to make sure the locking f unc­
tion is working, you should a lways keep
your eye on the vehicle to make sure it is
properly locked.
-
- Do not use the remote control if you are
inside the car, otherw ise you may unin­
tentionally lock the vehicle, and then you
would set off the anti-theft alarm when
you try to start the engine or open a
door. In case this happens anyhow, push
th e un lock button@.
- Use the panic function only if you are in
an eme rgency situation.
Locking and unlocking with Convenience
key
Appl ies to vehicles: with Conven ience key
The doors and the rear lid can be unlocked
and locked without operating the master key .
Fig. 30 Door handle: Lock ing the vehicle
Unlocking vehicle
.. Take hold of the door handle. The door is
unlocked automatically.
.. Pull the handle to open the door .

Locking v ehicle
• Move the selector leve r to the P position
(automatic transmiss ion), otherwise the ve ­
hicle cannot be locked.
• Touch th e sensor at the door hand le
c:> fig . 30 to lock the vehicle c:> A in General
description on page 39.
Do not reach inside
the door handle .
T he vehicle can be locked and unlocked at any
door. It depends on the settings in the radio
or in the
MM!* whether the entire vehicle is
unlocked or one of the doors
c:> page 39 . The
master key must be within a range of about
5 feet (1.5 meters) from the appropr iate door
or the rear lid .
It makes no difference whether
the master key is in your jacket pocket or in
your brief case.
If you grip the door handle while locking, this
can adversely affect the lock ing funct ion.
It is not possible to re -open the door for a
brief period directly after closing it . Th is al­
l ows you to ensure that the doors are properly
l ocked.
& WARNING
Read and follow a ll WARN INGS c:> &. in
General description on page 39.
@ Tips
-
If your vehicle has been standing for an ex­
tended period, please note the follow ing:
- The proximity sensors are deactivated af-
ter a few days to save power. You then
have to pull on the door handle once to
u nlock the veh icle and a second time to
open the veh icle.
- To prevent the battery from being dis­
charged and to preserve your vehicle's
ability to start for as long as possible,
the energy management system gradu­
ally switches off unnecessary conven­
ience funct ions. It is possible t hat you
will not be able to unlock your vehicle us­ i ng these conven ience functions .
Openin g an d clos ing 41
-For Declaration of Compliance to United
States FCC and Industry Canada reg ula·
t ions
c:> page 298.
Operating locks with the mechanical key
In the event of o failure of the power locking
system, the driver's door can locked and un­
locked with the mechanical key at the lock
cylinder.
Fig. 31 Key turns fo r open ing and clos ing
To unlo ck the vehicle
• Insert the mechanical key into the lock of
the dr iver's door .
• Turn the mechanical key to position @
c:>fig. 31 .
To lock th e vehicl e
• Move the selector lever to the P pos ition
(automat ic t ransm ission) .
• Close a ll windows and doors properly.
• Turn the mechanical key in the lock of the
d river's door to the lock position @
c:> A in
General description on page 39.
If the power lock ing system fails, there is
emergency lock ing for the passenger's doo r
and the rear doors
c:> page 42.
WARNING
Read and follow all WARNINGS c:> &. in
General description on page 39 .
(D Tips
-After the ignition is switched on, the
powe r locking system swit ch and the un­
locking button fo r th e rear lid~ in the
door are enab led .

50 Clear vis ion
stickers to the windshield in this area in
or der to prevent malfunctions or fai l­
u res .
- Some exte rior lig hti ng f unctions can be
adjusted
c> page 50 .
-When yo u remove yo ur key from the igni ­
tion while the vehicle's lights are turned
on, a buzze r sounds as long as the driv­
er's door is open .
- In coo l or damp weather , the ins ide of
the headlights, t urn signa ls and tail
li ghts can fog over due to the tempera­
ture difference between the inside and
outside. They will clea r sho rtly after
switching them on . T his does not affect
the service life of the lighting .
- In the even t of a light sensor malfunc­
t ion, the d river is no tified in th e inst ru­
ment cluster disp lay
c> page 33.
Fog lights
Fig . 44 Fog light sw it c h
.,. To tur n on the fog ligh ts iO, press button ©
c>fig . 44 .
.,. To tur n on the rear fog l ights Ot p ress but-
ton @.
Fog lights
The s ide marker lig hts or low beams must be
switched on . When the fog lights a re switched
on, the green check light at the edge of the
sw itch comes on.
If automatic driving light control AUTO is act i­
vated, the low beams are switched on when
the fog lights are tur ned on .
Rear fog lights
Low be ams o r sid e mar ker lights wi th fog
li gh ts m ust be t urned on .
When the rear fog lights a re turned on, the
yellow check ligh t a t the edge of the switch
comes on.
(D Note
The rear fog lights s houl d only b e turned
o n in acc ord ance wi th t raff ic reg ulation, a s
the lights are brig ht for following tra ffic.
Adjusting exterior lighting
The functions are sele cted in the radio or in
the MM I*.
.,. Select: !CAR ! function b utton> Ext erior
lighting .
Or
.,. Sele ct:
!CAR ! func tion b utton> Car sys­
tem s*
contro l bu tton > Vehicle setting s >
Exterior lighting.
Coming home (Lights when leaving car ),
Leaving home (Lights when unlocking car)
T he coming home f unct ion ill umi nates the
are a outside the vehicle whe n you tu rn the i g­
nit ion off and open the d river 's door . Depend­
ing on vehicle equ ipment, the f unction can be
switched on and off or the length of t i me the
lights remain on* can be adjusted .
T he leaving home illum inates the area outside
t h e vehicle when you unlock the vehicle . This
funct ion can be switched on and off .
T he Comi ng home and Leaving home f unc­
t io ns only ope rate when it is dark and the
light switch is in the
AUTO position .
Auto headlights
When the lig ht sw itch i s in the AU TO
c> page 49 position, the swi tch-on point of the
li gh ts can be changed i n the automa tic driving
light function.
Daytime running lights
USA models: You can swit ch the daytime run-
ning lights
On a nd Off . .,..

64 Seats and storage
Activating remote control key memory
Applies to vehicles: with seat memory
To assign the drive r's sea t settings to the re­
mote contro l key when locking the vehicle, the
function must be activated in the radio or
MMI* .
• Se lect :
IC ARI fu nct ion button> S eat adjust ­
m ent > Driver's seat > Ke y mem . profile
>
On . Or
· • Se lect:
~ IC _A_ R~ I function button > Car sys­
tems*
control button > Vehicle setting s >
Seats > Driver 's seat > Remote control ke y
> On.
@ Tips
If you do not want another driver's set­
tings to be assigned to the remote control key, switch
off the memory f unction using
the radio o r MMI* or the
IOFF I button
~page 63.
Rear seats
General information
Safe transp ortation of passengers on the rear
seats requires proper safety precautions.
A ll passengers on the rear seats must be seat­
ed i n complia nce w ith the safety g uidelines
explained in
~ page 149 and ¢page 157.
The correct seating posi tion is critical fo r the
safety of front
and rear seat passengers alike
~ page 142.
A WARNING
- Occ upants in the front and rear seats
must always be properly restrained.
- Do not let anyone ride in the vehicle
without the head restra ints provided.
Head restra ints help to reduce injuries.
- Loose items inside the passenger com­ partment, can f ly forward i n a crash or
sudden maneuver a nd injure occupa nts.
Always store art icles in the luggage com­
partment and use the fastening eyes, es­
pecially when the rear seatbacks have
been folded down. -
Read and heed all WARNINGS
¢ page 142 , Proper seating positions
for passengers in rear seats.
Adjusting seat
The fore-and-a~ adjustment of the seat cush­
ion and the seatback angle can be adjusted.
F ig . 63 Adjus ting seatback a ngle
Fig. 6 4 Fore-and-aft adjust ment
Adjusting seatback angle
• Pull the lever up and push the seatback to­
ward the rear to the desired posit io n
¢ fig . 63 . Release the lever .
• Pull the lever up so that the seatback pivots
forwa rd . Release the lever and push the
seatb ack to the rear to re turn the sea tba ck
t o the normal position .
Fore-and-aft adjustment
• Pull the ha ndle up and pus h the seat for ­
wa rd o r back
~ fig . 64 .
• Release the ha ndle and continue to push
t he seat until the seat latch engages.
A WARNING
- F or safety re asons, the seat must only be
ad justed when t he vehicle is stationary-
danger of acc ident! ,..

80 Warm and cold
Operation
We recommend pressing the IAUTOI button and setting the temperature to 72 °F (22 °C) .
Fig. 95 3 -zo ne de luxe automat ic cl imate contro l: controls
Press the buttons to turn the functions on or
off. Use the d ials to adjust the temperature,
the blower speed and the air dist ribution . Th e
L ED in a button wi ll light up when the func­
tion is switched on. The settings are disp layed
for a few seconds in the radio or MMI* display.
The driver and front passenger side can be ad­
justed separately. The settings are also dis­ p la yed in the climate control system display.
IOFFI Switching the climate control
system on/off
The IOFFI button switches the climate control
sys tem on or off. It also switches on when you
press the knob. Airflow from o utside is
b locked when the climate control system is
switched off.
IAC ! Switching cooling mode on/off
The air is not cooled and humidity is not re­
moved when cooling mode is switched off .
This can cause fog on the windows . Cooling
mode switches off a utomatica lly when the
outside temperature is below zero.
1 - 1 Switching recirculation mode on/off
In recircul ation mode, the air inside the vehi­
cle is circu lated and filtered . This prevents the
u nfiltered air outside the vehicle from enter­
ing the vehicle interior. We recommend switching
recirculation mode on when driving
th rou gh a tunnel or when sitting in traff ic
~&. -
The IAUTO I button or!@ FR ONT I button
switches recirculation mode off.
IAU TOI
Switching automatic mode on
Automatic mode maintains a constant tem­
perature inside the vehicle. Air temperature,
airflow and air distribution are controlled au­
tomat ically.
Adjusting the temperature
Temperatures between 60 °F (+16 °C) and
84 °F (+28 °C) can be set. Outside of this
range,
low or high will appear in the radio or
MMI* display . At both of these settings, the
climate control system runs continuously at
maximum cooling o r heating power. There is
no temperature regulation .
~ Adjusting the airflow
You can adjust the airflow manually to suit
your needs . To have the airflow regulated au­
tomatica lly, press the IAUTOI button .
~ Adjusting the air distribution
You can manually select the vents where the
air will flow. To have the a ir distribution regu­
lated automatically, press the !AUTO ! button.
IIJ,,

[i] Adjusting seat heating*
Pressing the button switches the seat heating
on at the highest setting ( leve l 3) . The LEDs
indicate the temperature level. To reduce the
temperature, press the button again. To
switch the seat heating off, press the button
repeatedly until the LED turns off .
After 10 minutes, the seat heating automati­
cally switches from leve l 3 to leve l 2.
lil Adjusting seat ventilation*
Pr ess ing the button switches the seat venti la­
tion on at the highest setting (level 3). The
LE Ds indicate the ventilation leve l. To reduce
the ventilation leve l, press the button again.
To switch the seat ventilat ion off, press the
button repeatedly until the LED turns off.
I.., FRONT I Switch the defroster on/off
The windshield and side windows are defrost­
ed or cleared of condensation as quickly as possib le. The maximum amo unt of air flows
mainly from the vents below the windshield.
Recirculation mode switches off . The tempera­
ture is controlled automat ically.
The
IAU TOI button switches the defroster off.
IClil REAR I Switching rear window heater
on/off
The rear window heater only operates when
the engine is running.
It switches off auto­
matica lly after a few minutes, depend ing on
the outside temperature.
To prevent the rear window heater from
switching off automatically, press and hold
the
lllii) REAR I button for more than 2 seconds.
This remains stored unt il the ignition is
switched off.
Air vents
You can open and close the center and rear air
vents using the thumbwheels . The levers ad­
just the direction of the airflow from the vents.
You can adjust the air temperature in the rear by turning the thumbwheel toward the red
Warm and cold 81
side to make it warmer or toward the blue
side to make it cooler .
A WARNING
-Do not use the recircu lation for extended
periods of time. The windows could fog
up since no fresh a ir can enter the vehi­
cle . If the windows fog up, press the air
recirculation button aga in immed iately
to switch off the air recirculation func­
tion or select defrost.
- Individuals with reduced sensitivity to
pa in or temperature could develop burns
when using the seat heating* funct ion.
To reduce the risk of injury, these individ­
uals shou ld not use seat heating.
(D Note
To avoid damage to the heating elements*
in the seats, do not kneel on the seats or
place heavy loads on a small area of the
seat.
(D Tips
The seat heating* only works when the
seat detects body weight on it. Placing ob­
jects on the seat could create enough
weight to switch seat heating on .
Setup
The basic climate control settings can be ad­
justed in the radio or MMI*.
.,. Select: I CAR I function button> A/C control
but ton. Or
.,. Select:
I CAR I function button > Car sys-
tems*
control button > AC.
Automatic recirculation
When switched on, automatic recirculation
controls the recirculation mode automatically.
If the windows fog up, press the lqj> FRON T I
button.
Synchronization
When synchronization is switched on, the
same settings are applied to both the driver
liJ>,

88 On the road
Driver messages
Ignition is on
This message appears and a warn ing tone
sounds if yo u open the dr iver's door when the
ignition is switched on.
No key identified
This message appears when the
I STAR T ENGIN E ST OP !* button is pressed if
there is no master key inside the vehicle or if
the system does not recognize it. For exam­
p le, the master key cannot be recognized if it
is co vered by an object (e.g. aluminum brief
case) which screens the radio signal. Electron­
ic devices s uch as ce ll phones can also inter­
fere with the radio signal.
Press brake pedal to start engine
This message appears if you do not press the
brake peda l to start the engine .
Shift to N or P to start engine
This message appears when attempting to
start the engine if the selector lever for the
automatic transmission is not in the P or N
position . The engine can only be started with
the selector in these posit ions .
!I Is the key in the vehicle ?
This message appears in a veh icle w ith Con­
ve nience key* if the master key is removed
from the veh icle with the engine running . If
the master key is no longer in the vehicle, you
cannot switch on the ignition after stopping
the eng ine and you also cannot start the en­
g ine again . Moreover, you cannot lock the ve ­
h icle from the outside with the key .
Shift to P otherwise vehicle can roll away.
Doors do not lock if lever is not in P.
This message appears for safety reasons
a long with a warning signal. It appears if the
selector lever for the automatic transm ission
is not in the P position when switch ing off the
ignition . Move the selector lever to the P pos i­
tion, otherwise the veh icle is not sec ured
against rolling away . You also cannot lock the vehicle
using the locking button* on the door
handle or using the remote key.
Turn off ignition before leaving car
Th is message appears if the driver's door is
opened wh ile the ignition is switched on. Al­
ways switch off the ignition if you are leaving
the vehicle. See also
r::} page 84 or¢ page 86.
Shift to P and turn off ignition, otherwise ve­
hicle can roll away
This message appears if the driver's door is
opened w hile the ignition is switched on and
t h e selecto r lever is not in the P position. Shift
the selecto r lever into the P position and
switch off the ignition when you exi t the vehi­
cl e. Otherwise the vehicle could roll. See also
¢ page 84 or¢ page 86.
Convenience key defective! Use ignition lock
This message appears if the engine must be
started or stopped using the ign ition key and
not the
I START ENGINE STOP I* button.
Electro mechanical
parking brake
Operation
The electromechonicol parking broke replaces
the hand broke.
Fig. 101 Cente r console: Park ing b rake
"' Pull on the switch ¢ fig. 101 to apply the
pa rking brake . The indicator light in the
sw itch ill uminates.
"' Step on the brake pedal or the accelerator
pedal and press the swit ch at the same time
to release the park ing brake. The indicator
light in the switch goes out.
Ill>

94 On the road
symbol appears in the display. The symbol's
appearance might be different in some mod­
els.
The speed warning system has
two warning
thresholds
that function independently of
each other and that have somewhat d ifferent
purposes:
Speed warning 1
You can use speed warn ing 1 to set the maxi­
mum speed wh ile you are dr iv ing. This sett ing
will remain in effect unt il you turn off the igni­
tion, assuming that you have not changed or
reset the setting.
The speed warning symbol. (USA models)/
• (Canada mode ls) in the warning 1 display
appears when you exceed the maximum
speed . It goes out when the speed fa lls below
the stored maximum speed.
The speed warn ing symbo l wi ll also go out if
the speed
exceeds the stored maximum speed
by more than about 25 mph (40 km/h) for at
least 10 seconds. The s tored maximum speed
is deleted .
Setting speed warning 1
c:!;> page 94 .
Speed warning
2
Storing warning 2 is recommended if you al ­
ways
want to be reminded of a certa in speed,
for example when you are trave ling in a coun­
try that has a general maximum speed limit,
or if you do not want to exceed a specified
speed for winte r ti res.
The speed warning 2 symbol ,. (USA mod ­
e ls)/ . (Canada models) appears in the dis­
p lay when you exceed the stored speed limit.
Unlike wa rning 1, it will not go out until the
vehicle speed drops below the stored speed
limit.
Setting speed warn ing 2
c:!;> page 94.
@ Tips
Even though your vehicle is equipped with
a speed warning system, you shou ld sti ll
watch the speedometer to make sure you are not driving faster than the speed limit.
Speed warning 1: setting a speed limit
Warning threshold 1 is set by the I SET I but­
ton .
Fig. 1 05 SE T butto n in th e instrumen t cl uster
Storing the maximum speed
• Dr ive at the desired maximum speed .
• Press the
ISETI button in the instrumen t
panel display ~
fig. 105 for 1 second .
Resetting the maximum speed
• Drive the vehicle at a speed of at least
3 mph (5 km/h)
• Press the
ISET I button for more than 2 sec-
onds.
T he speed warn ing symbol . (USA models)/
• (Canada models) will appear briefly in the
display when you release the
!SE T! button to
i ndica te that the max imum speed has been
stored successfully .
T he maximum speed remains stored until it is
changed by pressing the
!S ET ! bu tton again
briefly or until it is deleted by a lengthy push
on the button .
Speed warning 2: setting a speed limit
The MM!* or the radio control unit is used to
set, change or delete warning threshold
2.
• Select: !CAR lfunction b utton> In strument
cluster> Speed warning .
Or
.. Select: !CAR ! f unction button> Car sys·
tems*
control button > Driver assist >
Speed warning .
Warning threshold 2 can be set in the speed
range starting from 20 mph to 150 mph ..,.

112 Audi adaptive cruise control and braking guard
<:::::> ___ <:::::>_ Distance 3: This setting cor re-
sponds to a d istance of 164 feet/SO meters
when traveling at 62 mph (100 km/h), or a
time interval of 1.8 second s.
<:::::> ____ <:::::> Distance 4: This setting cor re-
sponds to a d istance of 210 feet/64 meters
when traveling at 62 mph (100 km/h), or a
time interva l of 2 .3 seconds .
A WARNING
Following other vehicles too closely in­
creases the risk of collisions and serious
personal injury.
- Setting short distances to the traffic
ahead reduces the t ime and distance
available to br ing your vehicle to a safe
stop and makes it even more necessary
to pay close attention to traffic.
- Always obey applicable traffic laws, use
good judgment, and select a safe follow­
ing distance for the traffic, road and
weather conditions.
(0 Tips
- Distance 3
is set automatically each time
you sw itch the ignition on.
- Your standa rd settings are automatically
stored and assigned to the remote con­
trol key being used
c:::> page 36.
Setting the driving program
Applies to vehicles: with Audi adaptive cruise control
Depending on the selected dr iving program
and distance, driving behavior when accelerat ­
ing will vary from dynamic to comfortable.
Setting the driving program for vehicles
without Audi drive select*
• In the radio/MMI*, select: !CAR !function
button
> adaptive cruise control > Driving
program
> Comfort, Standard or Dynamic .
Or
• Select : ICARI function button>
Car sys­
tems *
control button > Driver assist> Adap­
tive cruise control> Driving program
>
Comfort, Standard or Dynamic. Setting the driving mode for vehicles with
Audi drive
select*
Refer to c:::> page 121.
(D Tips
Your settings are automatical ly stored and
assigned to the remote control key being
used
c:::> page 36 .
· Request for driver intervention
Applies to vehicles: with Audi adaptive cruise contro l
Fig. 123 Inst rumen t cl uster: r eque st for dr ive r in te r­
ve ntion
In certain situations, the system will prompt
you to take ac tion . This could happen, for ex­
ample, if braking by the adaptive cruise con ­
trol system is not enough to mai ntai n enough
distance to the vehicle ahead.
The ins trumen t cluster will warn you abou t
the danger
c:::> fig. 123 :
-A red vehicle is p ictured in the display.
- The text
DISTANCE! appears in the stat us
bar .
- The red indicator light
I blinks.
- In addition, a warning tone sounds.

Audi adaptive cruise control and braking guard 113
Audi braking guard
Description
Applies to vehicles: with Audi adaptive cruise control
Fig. 124 Instrument cluste r: approac h warn ing
Braking guard uses a radar sensor. It also
functions within the limits of the system
when adaptive cruise control is switched off.
What can braking guard do?
When detected in time, the system can assess
situations when a vehicle ahead brakes sud­
denly or if your own vehicle is traveling at a
high speed and approaching a vehicle up
ahead that is moving more slowly . Braking
gua rd does not react if it cannot detect the
situation .
The system advises you of various situations:
- The
distance warning is given if you are too
close to the vehicle ahead for a long time. If
the vehicle ahead brakes sharply, you wi ll
not be able to avoid a collision. The indicator
light
I in the display comes on .
- The
approach warning is given when a de­
tected vehicle up ahead in your lane is mov­
ing much more slowly than you are or if it
brakes sharply . When this warning is given,
it may only be possible to avoid a collision
by swerving or braking sharply. The indicator
light
I and indicator in the display will warn
you about the danger
c:> fig. 124. You will al­
so hear an acoustic signal.
If you do not react fast enough or do not react
at all to the situation, braking guard will inter-
ll Th is is not ava ilable in som e coun tri es.
vene by braking and the message Braking
guard: Activated
will appear.
- If a coll ision is imminent , the sys tem wi ll
first provide an
acute warning by briefly and
sharply applying the brakes.
- If you do not react to the acute warning,
braking guard can brake within the limits of
the system. This reduces the vehicle speed
in the event of a collision.
- At speeds under 20 mph (30 km/h), the sys­
tem can initiate a complete deceleration shortly before a collision
ll.
- If the braking guard senses that you are not
braking hard enough when a collision is im­
minent, it can increase the braking force .
Which functions can be controlled?
You can switch braking guard and the dis­
tance/approach warning on or off in the radio/
MMI* i::!> page 114, Settings in the radio/
MMI *.
A WARNING
--==
Lack of attention can cause collisions, oth-
er accidents and serious personal injuries.
The braking guard is an assist system and
cannot prevent a collision by itself. The
driver must always intervene. The driver is
always respons ible for braking at the cor­
r ect time .
- Always pay close attention to traffic,
even when the braking guard is switched
on . Be ready to intervene and be ready to
take comp lete control whenever necessa­
ry. Always keep the safe and legal dis­
tance between your vehicle and vehicles
up ahead.
- Braking guard works within limits and
will not respond outside the system lim­
its, for examp le when approaching a
stopped vehicle or stationary obstacle (end of a traffic jam or vehicle that has
broken down in traff ic).