display AUDI Q5 2015 User Guide

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
The following information is continuo usly evalu­
ated by the trip computer and can be displayed
seq uent ia lly in the instrument cl uster display:
Fue l range
The estimated cruising range in m iles (km) ap­
pears in t he disp lay . This te lls you how fa r your
vehicle wi ll be able to travel on the current tank
of fuel and with the same driving style. The dis ­
p lay changes in increments of 5 mi les (10 km) .
Average fuel mileage
The average fue l economy in M PG (l/ 100 km)
since yo u last cleared the memory appears in this
disp lay . You can use this display to adjust your
driving technique to achieve a desired mileage .
Current fuel mileage
The instantaneous fuel consumption in miles per
ga llon (l/100 km) is shown in this display . Yo u
can use th is disp lay to adjust your d riving techni ­
q ue to achieve a desi red mileage .
F ue l consumption is reca lcula ted at interva ls of
33 yards (30 meters). This d isplay switches to
ga llons/ho ur (lite rs/hour) when the vehicle is not
moving.
Average speed
The average speed in mph (km/h) since the last
time the display was reset appears in the display.
Elapsed time
T he length of time that you have been driving
since you last reset the memory appears in this
d isp lay .
Distance
The distance that has been covered s ince the last
t ime the memory was cleared appears in the dis­
p lay .
@ Tips
-Fuel consumptions (average and current),
range and speed are disp layed in metric
units on Canadian models .
- All stored va lues w ill be lost if the veh icle
battery is disconnected.
Dri ver information s ystem
Memories
The trip computer is equipped with two fully au­
tomatic memories as well as an efficiency pro­
gram* .
Fig. 1 6 Trip comput er dis play: m emory lev el 1
You can switch between the trip computer 1 and
2 and the effici ency program* by pressing the
I RESET I button @ c> page 24, fig. 17 .
You can tell wh ich memory leve l is cu rrently ac ­
t ive by the number or the sign in the display
c> fig. 16. The data from the single-trip memory
(memory level 1) is being displayed if a
D ap­
pears in the display. If a fJ is shown, then the da­
ta from the total-trip memory is being d isplayed
(memory level 2) . The fue l pump nozzle
iii ind i­
cates the eff ic iency p rog ram *
c> page 25 .
Single-trip memory (Trip compute r 1)
The sing le-tr ip memory stores the tr ip info rma­
t ion from the time the ignition is turned on until
i t is turned off . If the trip is continued
within 2
hours
from the t ime the ignition was turned off,
the new data will be included in the calcu lation of
t h e curren t trip informat io n. If the trip is inter­
rupted for
more than 2 hour s the memory is re­
set automatically .
Total-trip memory (Trip computer 2)
Unlike the single-tr ip memo ry, the total-trip
memo ry is not reset automat ica lly. This permits
you to eva luate yo ur dr iv ing da ta fo r the ent ire
per iod between m anual resets.
Efficiency program*
T he efficiency program ca n he lp you to use less
fuel
c> page 25 .
23

Driver information system
Operation
The trip computer is controlled by two switches
on the windshield wiper lever.
g
~ a: (0 a,
~-- @
Fig. 17 Windshield w iper lever: controls fo r the trip co m­
puter
Operating
.. To display the trip computer memory levels,
press the
I RESET I button ®<=> fig. 17 repeated·
Ly until the desired memory level is shown in
the display.
.. To display trip information within a memory
level , press the top or bottom part of the func­
tion selection switch @.
The trip computer will not operate unless the ig·
nition is on. When you turn on the ignition , the
f unc tion that was in use when you last turned the
ignit ion off will be displayed.
In addition to information about the trip comput­
er (trip computer 1, 2 and the efficiency pro­
g ram*), information about other systems can al­
so be shown in the display. To switch the display
between the different information, tap the
I RESET I button® briefly.
Resetting values to zero
.. Select a value in the desired trip computer or in
the efficiency program* .
.,. Press and hold the
I RESE T I button @ for at
least one second. All values in the selected trip
computer or in the efficiency program* are re­
set to zero .
If the data in trip computer 1 are deleted, then
the values in the efficiency program * wi ll also be
reset.
24
With some vehicle equipment levels, the values
for the single trip or tota l trip memory can also
be reset in the radio or MMI*
¢page 24.
(D Tips
All stored values wi ll be lost if the vehicle bat­
tery is disconnected.
Basic Settings for the trip computer
The MMI* or the radio operating unit is used for
setting the trip computer's basic settings .
.. Select: !CAR ! function button > Instrument
cluster > On-board computer 1
or On-board
computer
2.
The values in the single-trip or the total-trip
memory can all be reset to zero at the same time
under
Reset in the menu.
In add ition, you can determine wha t infor mation
from the trip computer should be shown in the
i nst rument cluster display. If one of the pieces of
driver information is turned
Off, that driver infor­
mation will not be shown in the display. The in­
formation will continue to be calculated by the
trip computer and can be turned back
On at any
time .
(D Tips
-Th is function is not available on all vehicles.
- Th e driving information in the efficiency
program* is also reset to zero with the sin­
gle-trip memory.

M N
co ~ co
rl I.O
"' N
"' rl
Efficiency program
Description
Applies to vehicles: with efficiency program
Fig. 18 Display : efficiency program
" Press the I RESET I button @¢ page 24, fig. 17
repeatedly until the efficiency program appears
in the d isplay.
The efficiency program can help you to use less
fuel. It evaluates driving information in reference
to fuel consumption and shows other equipment in fluencing consumption. Fuel economy messag­
es¢
page 25 provide t ips fo r eff icient driving.
The efficiency program uses distance and con­
sumption data from trip computer
1. If the data
are deleted in the efficiency program, those val­
ues are also reset in trip computer
1.
Other equipment
A ppl ies to vehicles: with efficiency program
Fig. 19 Display: other equ ipment
" In the efficiency program, press the function
selection switch¢
page 24, fig. 17@ repeat­
edly until the other equipment appears in the
display.
Dri ver information system
Other equipment that is currently affecting fuel
consumption is listed in the efficiency program.
The display shows up to three other items of
equipment @. The equipment using the most
fuel is listed first. If more than three items using
fuel are switched on, the equipment that is cur­ rently using the most fuel is displayed.
A scale @also shows the current total consump­
tion of all other equipment.
Fuel economy messages
Applies to vehicles: wit h efficiency program
Fig. 20 Display: fuel economy message
Fuel economy messages are displayed when fue l
consumption is increased by certain conditions. If
you follow these fuel economy messages, you can reduce your vehicle's consumption of fuel. The
messages appear automatically and are only dis­
played in the efficiency program . The fuel econo­
my messages turn off automatically after a cer­
tain period of time.
" To turn a fuel economy message off immediate­
ly after it appears, press the
I RESET ! button
¢ page 24, fig. 17@, or
" Press the func tion select io n switch ¢
page 24,
fig. 17@.
(D Tips
-Once you have turned a fuel economy mes­
sage off, it will only appear again after you
turn the ignition on again.
- T he fuel economy messages are not dis­
played in every instance, but rather in inter­
vals over a period of time .
25

Driver information system
On Board Diagnostic
System (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢• in the
instrument cluster
c:::> page 14, fig. 8 is part of the
On-Board Diagnostic (OBD II) system.
The warning/indicator light i lluminates when the
ignition is switched on and goes out after the en­
gine starts and the idle has stabilized. This indi­
cates that the MIL is working properly.
If the light does not go out after the engine is
started, or illuminates while you are driving, a
malfunction may exist in the engine system. If
the light illuminates, the catalytic converter
could be damaged.
Continue driving
with reduced power (avoiding
sustained high speeds and/or rapid acce lerations)
and have the condition corrected. Contact your
authorized Audi dealer.
I f the light illuminates, the electronic speed lim­
iter may also be malfunctioning. For more infor­
mation
c::> page 26, Electronic speed limiter.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only vehicles
with gasoline engine)
c:::> page 216.
On-Board Diagnostics
F ig . 21 Locat ion of Data link Connector (DLC)
On-Board Diagnostics monitors the components
of yo ur emission control system. Each monitored
component in your engine system has been as­
signed a code . In case of a malfunction, the com­
ponent will be identified and the fault stored as a
code in the control module memory.
26
The MIL light may also illuminate if there is a
l eak in the on-board fuel vapor recovery system.
If the light illuminates after a refueling, stop the
vehicle and make sure the fuel filler cap is prop­
erly closed (only vehicles with gasoline engine)
c::> page 216.
In order to make an accurate diagnosis, the stor ­
ed data can only be displayed using specia l diag­
nostic equipment (generic scan tool for OBD).
In order to connect the specia l diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC) . The DLC is located to the right of the hood
release
c::> fig. 21.
Your authorized Audi dealer or qualified work­ shop can interpret the code and perform the nec­
essary repair .
A WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the r isk of a coll i­
sion!
Electronic speed limiter
Your vehicle may be factory equ ipped with tires
that are rated for a maximum speed of 130 mph
(210 km/h) . Th is is less than the max imum speed
of your veh icle. To reduce the risk of sudden tire
failure and loss of control if the vehicle is ope rat­
ed at excessive speeds, your vehicle also has an
electronic speed limiter . The electronic speed
limiter prevents your vehicle from going faster
than the tire speed rating. For more information
c::> page 242.
If the engine contro l unit receives faulty vehicle
road speed signals, the Malfunction Indicator
Lamp (MIL) ¢•will illuminate. If this occurs,
contact the nearest authorized Audi dealer for as­
sistance.
SQS
Your vehicle's top speed is electronically limited
to 155 mph (250 km/h).
If the engine contro l unit receives faulty vehicle
road speed s ignals, the Malfunction Ind icator ..,_

M N
co ~ co
rl I.O
"' N
"' rl
Lamp (MIL) ¢..ffi will il luminate. If this occurs,
contact the nea rest authorized Audi dea ler for as­
sistance.
.&_ WARNING
Always observe the posted speed limits and adjust your speed to suit prevailing road, traf­
fic and weather cond it ions . Never drive your
vehicle faster than the maximum speed rating
of the tires installed .
Auto Check Control
Introduction
The Auto-Check control monitors the function of
certain vehicle features and components .
It sim­
ply makes sure these features and components
are working properly . The Auto-Check control
works as long as the ignition is on, as well as
whenever the veh icle is driven .
-
If a component is malfunctioning or if the need
for an urgent repair has been detected, this will appear in the instrument cluster display . You w ill
also hear an audible warning tone . The displays
are color coded in either red or ye llow depending
on their level of prior ity.
A red symbol means
Danger , a yellow symbol in ­
dicates
Warning . In certain situations, informa­
tion message for the dr iver appear in addition to
the red and yellow symbols.
Note about automatic transmission
The Auto-Check Control will automat ically per­
form a test each time you switch o n the ignition .
With the selector lever in P or N, the following
message appears in the display :
When stationary apply brake pedal while select­
ing gear
When you select a different gear (for example: R,
D, etc.), the message will disappear and the Au­
to -Check function is d isplayed.
If there is a malfunction, then the malfunction
message will appear about 15 seconds after you
start the vehicle. At the same time you will hear a
warning tone.
Dri ver information system
Dr iver information messages
Driver information messages are shown in the in­
strument cluster display in addition to symbols .
Fig. 22 Inst rume nt clust er: SET button
For example, if the transmission selector lever is
not in the P position when the engine is turned
off, the following message appears :
Shift to P otherwise vehicle can roll away. Doors
do not lock if lever is not in P .
The ign ition key can only be removed w ith these­
lector in this position . This and other messages
are bro ught up if a function cannot be carried
out .
Driver messages and red symbols
If a red symbol appears in the display, a driver
message is also displayed automatically.
For example, the symbol for a problem w ith en­
gine oil pressure . appears in the display . The
fo llow ing message appears:
Turn off engine! O il pressure too low
T he driver message in the display goes out after
about S seconds . The dr iver message can be dis­
played again by briefly press ing the
ISETI button
9 fig . 22.
Driver messages and yellow symbols
If a yellow symbol appears in the display, a driver
message is also displayed automatically .
For example, the symbol
Ill appears in the dis­
play, indicat ing low windshie ld washer fluid level.
The following message also appears :
Please refill washer fluid ..,_
27

Driver inform ation system
The driver message disappears after a few sec ­
onds. The driver m essage can be displayed again
by briefly pressing the
I SETI button.
Red symbols
F ig. 23 Display: Dang er symbol
W ith a priority 1 malfunction, a red symbol ap­
pears in the upper center area of the disp lay
0 ~
"' 0 ci: a, al
¢ fig . 23. A driver message appears as well to ex­
p lain the ma lfunction in more detail. When this
symbo l appears,
three warning tones sound in
success ion . The symbol continues to flash until
the fault has been corrected .
If
several pr iority 1 malfunctions are present, the
symbo ls appear in succession and remain for
about 2 seconds.
The driver warning goes out after about 5 sec­
onds, but it can be brought up again at any time by pressing the
! SET ! button ¢ page 2 7.
28
Alternator fa i Lu re
¢ page28
Electromechanica l steering
¢ page 195
USA m odels : Brake system
malfunct ion
¢ page28
Canada models: Brake system
malfunct ion
¢page28
E ng ine coolant leve l too low/
engine coolant temperature
too high
¢ page29
Eng ine oi l pressure too low
¢ page30
Refi ll eng ine oi l now
¢ page 30
Refill Ad Blue*
¢ page 218
AdBlue malfunction*
¢ page 218
Steering malfunction
¢page30
Ign it ion lock malfunction
¢ page 30
Hybrid dr ive*
¢ page 100, ¢ page 1 OS
0 Alternator malfunction
If the . symbo l in the instr ument pane l display
flashes, then there is a malf unction in the alter ­
nator or the vehicle electronics . A warning to t he
driver will appear, too . The driver warning goes
out after about 5 seconds, but it can be brought up at any t ime by pressing the
ISE TI button again.
Usually, yo u can sti ll drive to the next dealership.
Turn off a ll but the most necessary electrica l con­
sumers, s ince these dra in the veh icle 's battery .
CJ) Note
If the . warning symbo l (coo lant system
malfunction) also lights up on the instrument
panel during the trip
¢ page 29, then you
have to stop immediately and turn off the en­
gine . The coolant pump is not working a ny­
more -da nger of damage to the eng ine !
BRAKE /C(D ) Brake system malfunction
A malfunction in the brake sy stem mus t be re­
paired as soon as possible .
If the warning/indicator light 1111 (USA mod ­
els)/ . (Canada models) in the instrument clus­
ter flashes, there is a brake system malfunction .
A d river message appea rs as well to expla in the
malfunction in more detail. The d river war ning
goes out after about S seconds, but it can be
brought up a t any time by pressing the
ISE TI but-
ton again. .,.

Driver information system
CJ) Note
Do not continue driving if the. symbo l ill u­
m inates. There is a malfunct ion in the engine
cooling system -you could damage your en­
gine.
9=:;r: Engine oil pressure malfunction
The red engine oil pressure warning symbol re­
quires immediate service or repair. Driving with a
low oil pressure indication is likely to cause se­
vere engine damage .
If the . symbol on the display flashes, the en­
g ine oil pressure is too low. A driver message ap­
pears as well to explain the malfunction in more
deta il. The dr iver warning goes out after about 5
seconds, but it can be brought up at any time by
p ress ing the
ISETI but to n again.
Turn off engine! Oil pressure too low
• Stop the vehicle .
• Turn the eng ine off .
• Check the eng ine oil level
c::, page 225.
• Contact your authorized Audi dealer for ass is -
tance if necessary.
Engine oil level too low
If the engine o il level is too low, add engine oi l
c::, page 225.
Engine oil level correct
If the symbol . flashes even though the engine
oil level is correct, please contact your nearest
authorized Audi Dealer for assistance. Do not
continue driving . Do not leave the engine running
idle, either.
(D Tips
- The engine oil pressure symbol. is not
an indicator for a low engine oil level. Do
not rely on it. Instead, check the oil level in
your engine at regular intervals, preferably each time you refuel, and always before
going on a long trip.
- The yellow oil level warning indication
Ill
requires oil refill or workshop service with­
out delay. Do not wait until the red oil
30
pressure warning • starts to flash before
you respond to the low oil level warning
II. By then, your engine may already have
suffered serious damage.
~ ... Fill engine oil now
WARNING: Please add oil immediately
If the . symbol lights up , then the oil has to be
replenished right now
c::, page 225.
@-Steering malfunction
If there is a malfunction in the electronic steer ­
ing column lock, the steering cannot be un­
locked.
If the . symbol in th e disp lay blinks, there is a
malfunction in the electronic steering co lumn
l ock. A driver message appears as well to exp lain
the malfunct ion in more deta il. The dr iver warn­
i ng goes out after about 5 seconds, but it can be
brought up at any time by pressing the
ISE TI but ­
ton again .
Steering defective! Do not drive vehicle!
• Contact your nearest authorized Audi dealer.
• Do
not tow your vehicle .
A WARNING
Your vehicle must not be towed in the event
of a malfunction in the electronic steering co l­
umn lock because it cannot be steered due to
the locked steering. If it is towed with the
steering locked, there is the risk of an acci­
dent.
© -Ignition lock malfunct ion
A malfunction in the ignition lock must be re­
paired immediately.
If the . symbo l in the display blinks, there is a
malfunction in the electronic ignition lock. A driv ­
er message appears as well to explai n the mal­
funct ion in more deta il. The driver warning goes
out after about 5 seconds, but it can be brought
up at any time by pressing the
ISETI button again.
Ignition lock defective. Contact dealer! ll-

M N
co
a:
co
,...., \!) 1.1'1
N 1.1'1 ,....,
~ Do not turn the engine off.
~ Drive immediately to an authorized Audi dealer
to have the malfunction corrected .
If there is a malfunction in the e lectronic ignition
l ock, the ignition cannot be turned off . Drive im­
mediately to an authorized service facility to have
the cause of the ma lfunction corrected.
On vehicles with Convenience key*, the engine
should not be switched off using the Start/Stop
button because the engine cannot be started
again after the ignition has been switched off.
Yellow symbols
Fig. 24 Display: Ye llow warn ing symbo l
N M
9 a: a, a,
When a ye llow warning symbol appears, one
warning tone so unds . A driver message appears
as we ll to exp la in the malf unction in more detail.
The driver warning goes out after about S sec­
onds, but it can be brought up at any time by press ing t he
ISETI button again.
Check the function d isp layed as soon as possible.
The yellow symbol w ill not go out aga in until the
reason for the malfunction has been corrected.
If several priority 2 malfunctions are present, the
symbols appear in succession and remain for
about 2 seconds.
Elect rom echan ica l steering, Dy­
namic steering*
¢page 195
Worn brake pads
¢page32
Battery voltage
¢page33
Driver information system
Defective light bulb
¢ page 32
Fog lights
¢page 32
Rear fog lights
¢page 32
Check engine oil leve l
¢page 33
Engine oil sensor malf unc tion
¢page 33
Engine temperature*
¢page 214
Low fuel level
¢page 33
Refill Ad Blue*
¢page 218
AdBlue malfunction *
¢page 218
Windshield washer fluid level
low
¢page 33
Convenience key*
Key not in veh icle
¢ page 32
Light/rain sensor defective
¢page 32
Dynamic headlight range con­
trol defective
¢ page 34
Battery in remote control key
¢page 37
Electromechanical parking
brake
¢page 91
Engine speed lim itation*
¢ page 33, ¢page 100
Diesel particulate filter* clog­
ged
¢ page 34
Adaptive light defective*
¢page 34
Steering malfunction
¢page 34
31

Driver inform ation system
Ignition lock malfunction
<=>page 34
Adapt ive dampers*
c:> page 34
W indshield wiper defective
c:>page34
Tire pressure monitoring sys­
tem*
Loss of t i re pressure
c:>page253
Tire pressure monitoring sys ­
tem* System not avai lab le
c:>page253
Automatic t ransmission ma l­
function
c:> page 12 7
H ybr id drive*
<=> page 100
The speed warnings warning threshold J IIIIJ
and warning thresho ld 2 llH are also yellow
symbo ls in some models . The warning is al­
ways shown as a small symbo l in the upper
area of the d isplay
c:> page 94.
-?e Key not in vehicle
Applies to veh icles: w ith Convenience key
II Is the key in the vehicle ?
This reminder appears along with the II symbol
if the master key is removed from the vehicle
with the eng ine running. It is intended to remind
you (e .g. when changing drivers) not to continue
the journey without the master key .
If the master key is no longer in the vehicle, you
cannot switch off the ignit ion after stopping the
e ngine and you a lso cannot start the engine
aga in . You also cannot lock the veh icle from the
outsid e.
l ) - : USA models only
32
@ Light/rain sensor defective
£1 Automati c he adlight s/ auto mati c wi per s
defective
If the symbol illum inates, the light sensor has
failed. For safety reasons the low beams are
tu rned on permanently with the sw itch in
AUTO .
However, you can contin ue to turn the lights on
and off using the light sw itch. In the case of a de­
f ect in the rain sensor, the windshie ld wiper lever
functions are still available. Have the light/rain
sensor checked as soon as possib le by an author­
i zed Audi dealer.
(0) Worn brake pads
E+J Brake pad s!
If the warning light i lluminates, immediate ly
contact your author ized Audi dealer or qualified
workshop to have all brake pads inspected. On
USA mode ls the warning light
E+J comes on to­
gether w ith the warning light
1111 . Both sets of
brake pads on an axle must always be replaced at
t h e same time.
.&_ WARNING
Driving w ith bad bra kes can cause a collision
and serious personal injury.
- If the warn ing lig ht E+J and the warn ing
light
llll1l with the message Brake pad s!
comes on in the instrument cluster display,
immed iate ly contact yo ur authorized Aud i
dea le r or q ualified workshop to have all
brake pads checked or rep laced if necessary.
~l}D10$ Defective light bulb warning
S:1 -If the indicator light turns on, a bulb has
failed. The message indicates the location of the
bulb .
Im-If a front fog lamp has fai led, the indicator
li ght turns on to indicate the location on the vehi-
cle.
~

M N
co
a:
co
,...., \!) ..,.,
N ..,., ,....,
IJ-If a rea r fog lamp has failed , the indicator
light turns on to indicate the location on the vehi­
cle.
Vehi cle light s: Sy stem fault!
If the message appea rs, there is a malfunct ion in
the head lights or light switch.
Drive to your authorized Aud i dea le r immediately
to have the malfunction corrected .
A WARNING
-Light bu lbs are pressurized and could ex­
plode whi le they a re being changed causing
serious persona l injury.
-
- Wor k w ith due care when handling the high­
voltage section of gas discharge (xenon) l igh ts *. Failure to do so could result in death
o r serious injury.
@ Tips
Have the bulb replaced or the connection re­
pa ired by your authorized Audi Serv ice depart­
ment.
<:;::> Windshield washer flu id level too low
llt Plea se refill wa sher fluid
If the symbol illuminates, add windshield washe r
fluid to the washer system and also to the head­
light washer system¢
page 234 .
Bil Fuel supply too low
When the D symbol i llum inates, this means
there are about 2 .6 gallons ( 10 liters) of fue l left
in the fuel tank. Time to refuel!
¢ page 215.
If the symbo l lights up, even when the re is ample
fue l in the tank, and the text
Fuel tank sy stem
malfun ction! Contact dealer
appears in the dis­
p lay, there is a fau lt in the system . Contact an a u­
thor ized Audi dealer to have the fault rectified.
D Battery voltage
If battery power drops into the range where it
can limit the abil ity of the engine to sta rt, th is
the symbo l(•) ::ippears in the instrument cluster
Driver information s ystem
display with the following driver message Lo w
batter y: Batte ry will be charged while d riving.
While t his d river no tification is disp layed, you
have to be prepa red fo r limited star ting capabili ­
ty .
Driver message appears and goes out again
If this drive r message appears after the ign ition
is tur ned on or while d riving a nd it goes ou t again
after a wh ile, the ba ttery has been adequa tely re ­
charged .
Driver message appears and does not go out
again
If this drive r notific ation appea rs after the ign i­
t ion is tu rned on or while dr iv ing and does not go
out again, the battery's state of charge is no t in
the optimal range. Start ing capability is restrict­
ed. Have the battery checked at an authorized
Audi dealer or other qualified workshop as soon as possible.
~ Check engine oil
II Add oil, ma x x qt (l) . You may cont . driv .
When the Ill symbol and dr iver message appear,
add the amount of oil appear ing in the disp lay at
the next opportunity ¢
page 225.
'l:7;,.. Engine oil sensor defective
• Oil le vel! Sen sor defective
If the symbol illuminates, contact yo ur author­
ized Audi dealer and have the oil sensor inspect­
ed . Until you have this done, check the oil level
each time you ref uel just to be on the safe s ide
¢ page 225.
!? Engine speed limitation
Applies to vehicles: with engine speed limitation
II! Do not ex ce ed max . engine speed of XXXX
rpm
T he II! symbol illuminates when there is a n en­
gine co ntro l malfunction . The indicato r light ~
i n t he i nstr ument cluster also illum inates. The
engine speed is limited to the speed displayed in .,,.
33