light AUDI Q5 2018 Owner's Guide

Lights and Vision
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph
(15 km/h) or turn t he ignition
off.
A WARNING
Curved mirror surfaces (for example convex)
enlarge the field of vision. However, they
make objects in the mirror appear smaller
and farther away. You may estimate incor­
rectly when you use these mirrors to gauge
your distance from the vehicles behind you
when changing lanes, which increases the risk of an accident.
«1j) Note
-Applies to vehicles with power folding exte­
rior mirrors: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­
er folding function to fold the mirror all the
way out. The mirrors will make a loud noise
when they latch into place. The mirror hous­
ing must not be moved back into place by
hand because this would impair the func­
tion of the mirror mechanism.
- Applies to vehicles without power folding
exterior mirrors : if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must move it back in place by hand.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Never fold power folding exterior mirrors*
by hand . Only fold them in and out using
the power controls.
(D Tips
-If the power adjusting function malfunc­
tions, the glass in both mirrors can be ad­
justed by pressing on the edge of it by hand.
- The exterior mirror settings are stored with
the memory
function*~ page 59.
so
Dimming the mirrors
Your vehicle is equipped with a manual or auto­
matic* dimming rearview mirror .
Manual dimming rearview mirror
.,. Pull the lever on the bottom of the mirror back.
Automatic dimming rearview mirror*
.,. The interior and exterior mirrors dim automati­
cally when light shines on them, for example
from headlights on a vehicle behind you.
A WARNING
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
can irritate the skin, eyes and respiratory sys­
tem. If there is contact with the fluid, flush immediately with plenty of water. Consult a
physician if necessary .
- Repeated or long-term exposure to electro­
lyte fluid can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leaving the vehi­
cle or, if this is not possible, open all of the
doors and windows as wide as possible.
- If electrolyte fluid enters the eyes, flush
them thoroughly with a large amount of
clean water for at least 15 minutes and then
seek medical attention.
- If electrolyte fluid comes into contact with
the skin, flush the affected area with clean
water for at least 15 minutes and then clean
with soap and water and seek medical at­ tention. Clean affected clothing and shoes
thoroughly before wearing again.
- If the fluid was swallowed and the person is
conscious, flush the mouth with water for at
least 15 minutes . Do not induce vomiting
unless this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately .
@ Note
If the glass on an automatic dimming mirror
breaks, electrolyte can leak out. This liquid
damages plastic surfaces and paint. Clean

u co ..... N r-­N .....
~ 0 co
this liquid as quickly as possible, for example
with a wet sponge.
@ Tips
- If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
will not function correct ly,
- The automatic dimming mirrors do not dim
when the interior lighting is turned on or
the reverse gear is selected.
Sun visors
Fig. 45 Sun visor
Sun visor
The sun visors for the dr iver and front passenger
can be re leased from their mounts and turned
to­
ward the doors ¢ fig. 45 (D.
They can also be moved back and forth length­
wise in this posit ion.
Vanity mirror
The -mir ror lighting- switches on when the cover
over the vanity mirror 2* opens .
Sunshade
App lies to: ve hicles with s unsh ad e
Fig. 46 Rea r door : sunshade
Lights and Vision
Rear door sunshade
.,. Pull the sunshade out and attach it to the re­
tainer on the upper door frame ¢ fig. 46.
Windshield wipers
Switching the wipers on
•®
• @
•@
@.
• @
•®
Fig. 47 Winds hield wiper leve r
(!)-
. ®
Fig. 48 Rear window wiper operat ion
Move the windshield wiper lever to the corre­
sponding position:
@ -Windshield w ipers off
co 0 ;&
a,
0 ;&
(D -Rain sensor mode . T he windshield wipers
switch on once the veh icle speed exceeds approx­
imately 2 mph (4 km/h) and it is raining. The
higher the sensitivity of the ra in sensor that is set
(switch ® to the right), the earlier the wind­
shield wipers react to moisture on the wind­
shield. You can deactivate the rain sensor mode
in the Infotainment system, which switches the
intermittent mode on . To do this, select:
I MENU I
button > Vehicle > left control button > Driver
as sistance > Rain sensor.
In interm ittent mode,
you can adjust the interval time using the switch
®·
@ -Slow w iping .,.
51

Lights and Vision
@-Fast wiping
©-Single wipe. If you hold the lever in this posi­
tion longer, the wipers switch from slow wiping
to fast wiping .
®-Clean the windshield . The wipers wipe one
time after several seconds of driving to remove
water droplets . You can switch this function off
by moving the lever to position ® within
10 sec­
onds of the afterwipe. The afterwipe function is
r e activated the next time you switch the ignition
on.
Clean the headlights*. The headlight washer sys­
tem* operates only when the low beam head­
lights are on. If you move the lever into position
@, the headlights will be cleaned at fixed inter­
vals .
@-Wipe the rear window. The number of wipes
depends on the windshield wiper movement.
The rear wiper automatically switches on when
the reverse gear is selected and the front wind­
shield wipers are on and running.
(j) -Clean the rear window. The number of wipes
depends on how long the lever is held in position
(z). This may also clean the rearview camera, de­
pending on the vehicle equipment.
A WARNING
- The rain sensor is only intended to assist the
driver. The driver may still be responsible
for manually switching the wipers on based on visibility conditions.
- The windshield may not be treated with wa­ ter-repelling windshield coating agents . Un­
favorable conditions, such as wetness, dark­
ness or low sun, can result in increased
glare, which increases the risk of an acci­
dent. Wiper blade chatter is also possible.
- Properly functioning windshield wiper
blades are required for a clear view and safe
driving ~ page 53, Replacing wiper
blades .
«1j) Note
-If there is frost, make sure the windshield
wiper blades are not frozen to the wind-
52
shield. Switching on the windshield wipers
when the blades are frozen to the wind­ shield can damage the wiper blades.
- The windshield wiper system must be
switched off (lever in position 0) before us­
ing a car wash. This prevents the wipers
from switching on unintentionally and caus­ ing damage to the windshield wiper system.
(D Tips
- The windshield wipers switch off when the
ignition is switched off. You can activate the
windshield wipers after the ignition is
switched back on by moving the windshield
wiper lever to any position .
- Worn or dirty windshield wiper blades result
in streaking. This can affect the rain sensor
function . Check your windshield wiper
blades regularly.
- The washer fluid nozzles for the windshield
washer system are heated at low tempera­
tures when the ignition is on.
- When stopping temporarily, such as at a
traffic light, the speed of the windshield
wipers automatically reduces by one level.
Cleaning the wiper blades
Clean the wiper blades when you see wiper
streaks. Use a soft cloth and a glass cleaner.
Windshield wiper
.,. Place the windshield wiper arms in the service
position
~ page 53.
.,. Fold the windshield wiper arms away from the
windshield.
Rear window wiper
.,. Fold the wiper arm away from the rear window.
A WARNING
Dirty windshield wiper blades can impair vi­
sion, which increases the risk of an accident.
-

u co ..... N r-­N .....
~ 0 co
Replacing wiper blades
Fig. 49 Remov ing w indshi el d w iper blades
Windshield wiper serv ice po sition /blade
replacement position
"' To bring the windshield wipers into the service
pos ition, turn the ignition off and move the
windshield wiper lever into position @
¢ page 51, fig. 47.
"'T o bring the windshield wipers back to the nor­
mal pos ition, switch the ignition on and hold
the windshie ld wiper lever in posit ion @ until
the windshie ld wipers go back to the normal
pos ition, or d rive faster than 8 mph (12 km/h) .
You can a lso tu rn the service position on or off in
the Infotainment system :
"'Switch the windshield wipers off (position @
¢page 51 , fig. 47) .
"'Select : the I MENU ! button> Vehicle> left con­
trol button >
Service & checks > Wiper change
position .
Removing the wiper blade
"'Fold the windshield wiper arm away from the
windshield .
"' Press the locking knob (D ¢ fig. 49 on the wiper
blade . Hold the wiper blade firmly .
"'Remove the wiper blade in the direct ion of the
arrow .
Installing the wiper blade
"'Insert the new wiper blade into the mount on
the wiper arm
@ until it clicks into place.
"'Place the wiper arm back on the windshield .
"'Turn the serv ice position off.
Lights and Vision
A WARNING
For safety reasons, the windshield wiper
blades should be replaced once or twice each
year .
(D Note
- Only fold the windshield wipers away when
they are in the service pos ition. Otherwise,
you risk damaging the paint on the hood or
the windshield wiper motor .
- You should not move your veh icle or operate
the windsh ield wiper lever when the wiper
arms are folded away from the windshield .
Th e windshield wipers would move back in­
to their or iginal pos ition and could damage
the hood and windshield.
- T o red uce the risk of damage to the wiper
system, always loosen blades wh ich are fro­
zen to the windshield before operating the
w ipers.
- To reduce the risk of damage to the wiper
blades, do not use gasoline, kerosene, paint
thinner, or other solvents on or near the
wiper blades.
- To reduce the risk of damage to the wiper
arms or other components, do not attempt
to move the wipers by hand.
(D Tips
- You can also use the service position, for ex­
ample, if you want to protect the windshield
from icing by using a cover .
- You cannot activate the service posit ion
when the hood is open .
Replacing rear wiper blade
Fig . SO Rear w indow wiper : installing the w ip er blade
53

Lights and Vision
Removing the wiper blade
• Fo ld the wiper arm away from the rear window .
• Remove the wiper blade from its holder.
Installing the wiper blade
• Press the wiper b lade mount into the retainer.
• Fo ld the window wipe r arm bac k onto the rear
window.
WARNING
F or safety reasons, the windshie ld wiper
blades sho uld be replaced once or twice each
year .
Digital compass
Switching the compass on and off
App lies to: ve hicles w ith digital compass
F ig . 51 Re arview m irror : dig it al co mpass is sw itc hed o n
54
• To turn the compass on or o ff, press the button
@ unti l the compass in the mi rror appears or
disappears.
The dig ita l compass o nly works when the ignit ion
i s turned on . T he directions a re indicated with ab­
breviations:
N (north), NE (northeast), E (east),
SE (so utheast), S (so uth), SW (southwest), W
(west), NW (northwest) .
(D Tips
To prevent inaccurate compass readings, do
not br ing any remote contro ls, electrical devi­
ces or metallic objects near the mirror.

u co ..... N r-­N .....
~ 0 co
Lights and Vision
Adjusting the magnetic zone
Applies to: ve hicles with d ig ital compass
The magnetic zone must be adjusted correctly for the compass to read accurately.
Fig . 52 Magnetic zone map
• Press and hold the button @ Q page 54, fig . 51
until the number of the selected magnetic zone
appears in the rearview mirror .
• Press the button@repeatedly to select the
correct magnetic zone . The selection mode
turns off after a few seconds.
Calibrating the compass
A ppl ies to: ve hicles w ith d ig ital compass
If the display is incorrect or inaccurate, the com­
pass must be recalibrated.
• Press and hold the button @ until a C appears
in the interior rearview mirror .
• Drive in a circle at about 6 mph (10 km/h) until
a direction is displayed in the interior rearview
mirror.
A WARNING
To reduce the risk to yourself and other driv­
ers, calibrate the compass in an area where
there is no traffic.
.
55

u co ..... N r-­N .....
~ 0 co
• To select a seat setting, turn the multifunction
button
CD in the corresponding direction until
the desired seat setting is outlined in red.
• The arrows @ represent the possible adjust­
ments . For example, to lower the lumbar sup­
port , press the multifunction button
CD down.
The corresponding arrow @ lights up.
The following seat sett ings @are possible:
Massage function* -select the massage type
Wave , Stretch, Knead or Off You can adjust the
intensity of each massage from 1 to 3. You can
switch the selected massage on/off using the button @¢
fig. 55 .
lumbar support -you can adjust the lumbar sup­
port up/down and to be stronger/weaker.
@ Tips
The massage function switches off automati­ cally after approximately 10 minutes.
Center armrest
There is a storage compartment under the arm­
rest.
Fig . 56 Comfort cente r armr est between t he driver 's sea t
and front passenger 's seat
• T o adjust the angle, raise the armrest from the
starting position notch by notch.
• To bring the armrest back into the starting po­
sit ion, ra ise it out of the top notch and fold it
back down.
The armrest can slide forward and back.
Seats and storage
Rear seats
Adjusting the seats
Fig. 57 Adjust ing the angle of the backrest*
Fig. 58 Adj usting forw ard and backwa rd*
Adjusting the angle of the backrest*
• Pull the lever upward and push the backrest
back to the des ired position ¢
fig. 57. Release
the lever and press the backrest farther back
until it locks in place .
• Pull the handle upward so th at the back rest will
tilt forward. Release the lever and pus h the
backrest back to put the back rest in its basic
position.
Adjusting forward and backward*
• Pull the handle up and slide the seat forward/
back ¢fig. 58.
• Release the handle and continue sliding the
seat until it locks in place.
_& WARNING ~
-To reduce the risk of an accident, the seat
can only be adjusted when the vehicle is sta ­
tionary.
- Adjusting the seat without paying attention
can pinch fingers or lim bs, which increases
the risk of injury.
-
57

Seats and stor age
-In the doo r trim pane ls
-Stor age compartment under t he front cente r
armrest
-Garment hooks above the rear doo rs
-Nets* on the left/right luggage compartment
trim pane l
-Tie-downs* on the left/right luggage compart­
ment t rim pa nel
-Bag hooks* in the luggage compartment
A WARNING
-
- Always keep t he g love compartment lid
cl osed while driving to reduce the r is k of in­
Jury.
-Only use the storage compartments in the
doo r trim pa ne ls to s to re small objects that
will not st ick o ut of t he compa rtment and
impa ir the range of t he side a irbags.
-Due to strength reasons, only secure objec ts
up to 11 lbs (5 kg) with the tie-downs* .
Heav ier objects are not adequately sec ured .
There is risk of persona l injury.
-Make s ure that the view to the rear is not
obstructed by hanging garments.
-Hang on ly lightwe ight cloth ing and be su re
t h at there a re no heavy or sha rp -edged ob ­
jects in the pockets.
-Do n ot use coat hangers to h ang the cloth­
ing because t his could impair the effective­
ness of the side cu rtain airbags .
Luggage compartment
General information
A WARNING
Read and follow t he important safety p recau­
tions in
q poge 257 , Storing cargo correctly.
62
Luggage compartment cover
Applies to: vehicles with luggage compartment cover
Fig. 67 Lugga ge compar tme nt: c ove r attac hed
Fi g. 68 Lu gga ge compartme nt: remov ing and ins tall ing
t he lu ggage com part ment c ove r
Attaching
.,. Pull the cover o ut and attach it in the mo unt ing
eyelets in the side trim panel
q fig. 67.
Removing
... Pull both levers in the direction of the arrow
q fig . 68 and remove the cover upward.
Installing
... Place the left and right sides of the cover into
the moun ts on the s ide trim panel.
... Push the cover downward until it clicks into
place .
A WARNING
The luggage compar tment cover is not a sur­
fa ce for sto rin g objec ts. O bjects pl aced on the
cover could endange r a ll veh icle occup ants
d ur ing sudden braking maneuvers or in a
crash .
-

Drivin g
engaged, for examp le when you notice that the
next traffic light is red . This produces an engine
braking effect, which helps to protect the brakes
and tires and reduces the emissions and fuel con­
sumpt ion to zero (fuel shut-off during decelera­
tion) .
Shift effici entl y
Upshifting earlier is an effective way to save fuel.
Staying in a gear too long uses fue l unnecessari­
ly .
Press down on the acce lerator peda l slowly and
avoid "kick -down".
Avoid full acceleration
You shou ld rare ly t ravel at the maximum vehicle
speed. High speeds cause a d isp ropor tionately
high increase in fuel consumption, emissions and
traffic noise . Driving more slowly saves fue l.
Reduce idling time
The Start/Stop system* helps to reduce the idling
time automatically. In vehicles witho ut the Start/
Stop system* , it is
efficient to switch the eng ine
off when stopped at rai lroad crossings and long
red lights . Stopping the engine for
30 -40 sec ­
onds already saves more fu el than the amount of
extra fuel needed to restart the engine.
It t akes a very long time in idle to wa rm the en ­
gine up to operating temperature . Wear and
emissions are especially high in the warm -up
phase. Therefore, you should begin driving im­
mediately after starting the engine. Avoid high
RPMs while do ing th is .
Ha ve mainten anc e performed regularly
By having maintenance performed regu lar ly on
your veh icle, you can he lp to reduc e fuel con­
sumpt ion before you even start to dr ive. The
maintenance condition of your vehicle not only
affects traffic safety and long -term value but al­
so impacts fuel consumption . A poorly main­
tained engine can lead to fuel consumpt ion that
is
1 0% hi gher tha n normal.
74
Avoid short trip s
The engine and exh aust clean ing system mus t
reach their optima l operating temperature to ef­
fective ly reduce consumption and emissions.
A cold engine uses a d isp roportionately high
amoun t of fue l. The eng ine re aches opera ting
temperat ure and cons umption norma lizes on ly
after approximate ly 2.5 mi les (4 km) .
Check the tire pressure
To save fue l, ma ke sure the t ires are always in­
flated to the correct
press ure~ page 335. The
fuel consumpt ion can increase by
5% if the pres ­
sure is on ly
0 .5 bar too low. Due to t he increased
rolling resistance, low tire pressures wi ll also
l ead to greater tire wear and will affect driving
behavior.
Do not drive on winter tires year -round, as this
will consume up to
10% more fue l.
Eliminat e unnecessary weight
Since eve ry po und of ext ra weight increases f uel
consump tion, a quick inspec tion of the luggage
compartment may be worth it to avoid unneces ­
sary weight .
When not be ing used , a roof rack sho uld be re ­
moved to decrease the w ind resis tance of the ve­
hicle . This will save you approx imately
12% fue l
at speeds from
6 2 -75 mph (100 -120 km/h) .
Save energy
The eng ine d rives the generator, which generates
electr ic ity; the f uel consumpt ion also inc reases
wi th the demand for e lec tricity . T he refore, sw itch
electrica l eq uipment o ff when you no longe r
need it . Examples of eq uipment that uses a lot of
energy are air blowers at a high setting, the rear
window defogger and seat heating* .
@ Note
Do not leave engine idling unattended after
starting. If warning lights s houl d come on to
i ndicate improper operation, they would go
unheeded. Extended idling also produces
h eat, which could result in overheating or
other damage to the veh icle or othe r proper­
ty .

u co ..... N r--­N ..... 0 <( 0 00
@ Note
Avoid high engine speed, full throttle, and heavy engine load if the engine has not
reached operating temperature yet. You could
damage the engine.
@) For the sake of the environment
Do not let the engine run while parked to
warm up. Begin driving immediately. This re­ duces unnecessary emissions.
(D Tips
- Some noise after starting the engine is nor­
mal and is no cause for concern.
- If you leave the vehicle with the ignition
switched on, the ignition will switch off af­
ter a certain amount of time. Make sure that electrical equipment such as the exterior
lights are switched off.
Starting the engine
"'Bring the vehicle to a full stop.
"'Press the I START ENGI NE STO PI button
C? page 76, fig. 86.
Emergency off function*
If it is absolutely necessary, the engine can also
be turned off while driving at speeds starting at
4 mph (7 km/h). To switch the engine off, press
the
! START ENGINE STOPI button twice in a row
briefly or press and hold for longer than two sec­
onds.
A WARNING
- Never turn off the engine before the vehicle
has come to a complete stop. The full func­
tionality of the brake booster and the power steering is not guaranteed. You must use
more force to steer and brake the vehicle.
The fact that you cannot steer and brake as
usual can increase the risk of accidents and
serious injuries.
-If you leave the vehicle, switch the ignition
off and take the vehicle key with you .
If you
do not, the engine could be started and
electrical equipment such as the power win-
Driving
dows could be activated. This can lead to se­
rious injuries.
- For safety reasons, always park the vehicle
with the selector lever in the "P" position.
Otherwise, there is the risk that the vehicle
could roll unintentionally.
@ Note
If the engine has been under heavy load for
an extended period of time, heat builds up in
the engine compartment after the engine is
switched off and there is a risk of damaging
the engine . For this reason, let the engine run
at idle for approximately two minutes before
shutting it off.
(D Tips
For up to 10 minutes after stopping the en­
gine, the radiator fan may turn on again auto­
matically or it may continue to run (even if
the ignition is switched off) for the following
reasons :
- The coolant temperature is increasing due
to
trapped heat.
- If the engine is warm and the engine com­
partment also heats up from strong sun­
light.
Messages
Engine running. Warning! Turn off ignition be­
fore leaving vehicle
This message appears and a warning tone sounds
if you open the driver's door when the engine is
running.
Please press the brake pedal
This message appears if you do not press the brake pedal when starting the engine .
Ill Remote control key: key not detected. Is the
key still in the vehicle?
This indicator light turns on and this message ap­
pears if the ignition key was removed from the
vehicle when the engine was running. If the igni­
tion key is no longer in the vehicle, you cannot
switch on the ignition or start the engine once
..,.
77