display AUDI Q7 2010 Owner´s Manual

Driver information display
On-Board Diagnostic system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) • in the instrument cluster
~ page 14, fig. 7 is part of the On-Board Diagnostic (OBD II) system.
Th e warn ing/indicator light illuminates when the ignition is switched
on and goes out after the engine starts and the idle has stabilized.
Thi s ind icates that the MIL is working properly.
If
the light does not go out after the engine is started, or illuminates
while you are driving , a ma lf u nction may exist in the engine system.
If the light illuminates, the catalytic converter could be damaged.
Continue driving
with reduced power (avoiding sustained high
speeds and/or rapid accelerat ions) and have the condition corrected .
Contact your authorized Audi dealer .
If the light i lluminates, the electronic speed limiter may also be
malfunctioning. For more information~
page 26, "Electronic speed
limiter".
An improperly closed fuel filler cap may also cause the MIL light to
illuminate (only vehicles with gasoline engine)~
page 290. •
On-Board Diagnostics
Fig . 15 Location of
Data Link Connector
( DLC)
On-Board Diagnostics monitors the components of your emission
control system. Each monito red component in you r engine system
has been ass igned a code. I n case of a malfunct ion, the component
wi ll be ident ified and the fau lt stored as a code in the control module
memory .
The MIL light may also illuminate if there is a leak in the on-board fuel
vapor recove ry system. If the light illuminates after a refuelling, stop
the vehicle and make sure the fuel filler cap is properly closed (only
veh icles with gasoline engine)~
page 290.
I n order to make an accurate diagnosis, the stored data can only be
displayed using special diagnostic equipment (generic scan tool for
OBD).
In order to connect the special diagnostic equipment, push the plug
into the Data Link Connector (DLC). The DLC is lo cated to the right of
the hood release ~ fig. 15.
Your authorized Audi dealer or qualified workshop can interpret the
code and perform the necessary repair .•
Electronic speed limiter
Your vehicle may be factory equ ipped w ith tires that are rated for a
maximum speed of 130 mph (210 km/h). This is less than the
maximum speed of your veh icle. T o reduce the risk of sudden tire
fai lure and loss of contro l if the vehicle is operated at excessive
speeds, your vehicle a lso has an electronic speed limite r. The elec­
tronic speed limiter prevents your vehicle from going faster than the
tire speed rating. For more information ~
page 326.
If the eng ine control unit receives faulty veh icle roadspeed signals,
the Malfunction Indicator Lamp (M IL) ..... will illuminate. If this
occurs, contact the nearest authorized Aud i dealer for ass istance . _.,

& WARNING
Always observe the post ed speed limits and adjust your speed to
s uit prevailing road , traffic and weather condition s. Never drive
your vehi cle faster than the m aximum sp eed rating of the tires
installed .•
Auto Check Control
Introduction
The Auto-Check control monitors the function of certain vehicle
featu res a nd compo nents. It s imp ly makes su re t hese featu res and
components are working properly. The Auto-Check contro l works as
long as the igni tion is on, as we ll as whenever the veh icle is d riven.
If a compone nt is malfunctioning or if the need for an urgent repair
has been detected, this will appea r in the instrument cluster display .
You will also hear an audible warn ing tone . The d isp lays are colo r
coded in e ither red or yellow depend ing on their level of prior ity.
A red symbol means
Danger , a yellow symbol ind ic a tes Warning . In
certain situations, information message for the driver appear in addi­
t ion to the red and ye llow symbo ls.
Function test: automatic transmission
Th e Auto- Che ck Contro l will a utomat ica lly perfo rm a test ea ch t ime
you switch on the ignition. With the selector lever in
P or N, the
f ollowing mess age appears in t he disp lay:
When stationary apply foot brake while selecting gear.
When you a se lect a diffe rent gea r (for example : R, D , etc .), the
message w ill dis appea r and t he Auto-Check f unctio n is d isplayed.
If there is a ma lfunction, then the malfunction message will appear
abou t 15 seconds after the you start the veh icle . A t the same time
you will hea r a warni ng tone .•
Controls and equip ­
ment Safety first
Driver information display
Driver information messages
Dr
ive r inf orma tion messa ges a re sh ow n in the instru­
ment clus ter dis play i n addition to t he red a nd yell ow
symbols.
Fig . 16 Instrumen t
clu ster: CHE CK button
For examp le, if the transm ission selector lever is not in the P posit ion
w hen the eng ine is tur ned off , the foll owing message appea rs :
Shift to P otherwise vehicle can roll away. Doors do not lock if
you are not in P.
Th e ig nitio n key can only be removed w ith the se lector in this pos i­
tion. This and othe r messages are bro ught up if a function cannot be
c a rried out .
Driver messages and red symbols
If a red symbol appears i n the d isplay, a driver message can be s hown
by pressing the
! CHECK) button.
F or ex ample, the sym bo l for a prob lem wi th engine o il press ure~
appears in the display.
If you the n press the I CH ECK ) button, the
f ollowin g dr iver mes sage appears in the displ ay :
Switch off engine ! Oil pressure too low
The driver message in the display goes o ut after about 5 seconds . The
dr ive r m essage can be d isp laye d a gai n by briefly pres sing the
!CHECK ) button. .,.
Vehicle care Technical data

Driver information display
Driver messages and yellow symbols
If a yellow symbol appears in the display, a driver message is also
displayed automatically.
F o r example, the symbol appears in the display, indicating low
windshield washer fluid level. The following message also appears :
Please refill washer fluid
The driver message disappears after a few seconds. The driver
message can be displayed again by briefly pressing the [
CHECK]
button.•
Red symbols
A red symbol means DANGER.
-Pull off the road.
- Stop the vehicle.
- Turn off the engine.
Fig. 17 Display:
engine coolant level
warning (priority 1)
-Check the malfunctioning system. Contact your autho-
rized Audi dealer or a qualified workshop for assistance.
Red symbols indicate a priority 1 malfunction. Danger! With a priority 1 malfunction, a large symbol appears
in the center
area of the display => fig .
17. When the symbol appears, three
warning tones sound in succession . The symbol continues to blink
until the malfunction has been repaired.
If there are
more than one priority 1 malfunctions, the symbols
appear one after the othe r for about
2 seconds .
An additional driver message can also be displayed by briefly pressing
the (
CHECK ] button.
The red symbols mean :
0
BRAKE
CCD>
Alternator malfunction
USA models:
Brake system malfunction
Canada models:
Brake system malfunction
Engine coolant level too
low/engine coolant temperature
too high
~ Engine oil pressure too low
Ad Blue
/8' Refill AdBlue*
f Faulty steering
Faulty ignition switch
(I) Tips
=> page29
=> page29
=> page29
=>page 30
=> page 30
=>page292
=> page 31
~page31
• If the warning/indicator light BRAKE (USA models)/ ((!)) (Canada
models) in the instrument cluster flashes, there is a brake system
malfunction . By pressing the (
CHECK) button, you can bring up a
driver message which explains the malfunction in more detail. Please
note =>
page 29. .,_

• Speed warnings threshold 1 8 (USA models)/9 (Canada models)
and thresho ld 2
e , (USA mode ls)/ 0, (Canada models) are also s hown
as red symbols . The warning is always shown as a small symbol in the
upper area of the display ~
page 35. •
Alternator malfunction 0
If the D symbol in the instrument panel d isplay flashes, then there
is a malfunction in the alternator or the vehicle electronics . A warning
to the driver wi ll appear, too. The driver warning goes out after about
5 seconds, but it can be brought up at any time by pressing the
[CHECK] button again.
Us ua lly, you can sti ll d rive to the next dea le rship . T urn off all but the
most necessary e lectr ica l consumers, s ince these dra in the vehicle's
battery.
0 Note
If the _f-warning symbol (coolant system ma lfunction) a lso lights up
on the instrument panel during the trip~
page 30, then you have to
stop immediate ly and t urn off the engine. The coolant pump is no t
work ing anymore -danger of damage to the engine! •
Brake system malfunction
A malfunction in the brake system must be repaired as
soon as possible.
If the warning /indicator light BRAKE (USA mode ls)/ CCD)
(Canada models) in the instrument cluster flashes, there is a
brake system ma lfunction. By press ing the
[CHECK ] button,
you can bring up a driver message which exp lains the
malfunction in more deta il.
Controls and equip ­
ment Safety first
Dri
ver information display
Stop vehicle and check brake fluid Level
- Pull off the road.
- Stop the veh icle .
- Turn off the eng ine .
- Check th e brake flui d level =>
page 307.
-Contact your nearest authorized Audi dea ler or qualified
workshop if necessary.
Warning ! Fault in brake system. Contact
workshop
- Drive carefully to the neares t author ized Audi dealer or
qualified works hop and have the malfunction corrected
=> & .
If the ABS system malfunctions, the ABS warning/indicato r light illu­
minates together with the b rake system malfunction warning/ indi ­
cator light~& .
& WARNING
• Alw ay s ob serve the warning s in ~ page 28 6, "Engine c ompart­
m ent ", before opening th e hood and che cking the b rake fluid .
• Driving with low brake fluid is a safety hazard. Stop th e car and
get profe ssional a ssistan ce.
• USA model s: If the BRAKE warning light an d the \6:> warning
light com e on together, the rea r wheel s could lo ck up fir st under
hard braking . R ear wh eel lo ck -up c an cau se lo ss of vehi cle control
and an a ccident . Have your v ehicl e repair ed immedia tely by your
authorized Audi dealer or a qualified work shop. Dr ive slowly and
avoid sudd en, hard brake applications .
• Canada model s: If the brake warning light CCI» and the ABS
warning light come on togeth er, the rear wheels could lo ck up
fir st unde r hard b raking. Rea r wheel loc k-up c an cause lo ss of
~
Vehicle care Technical data

Driver information display
& WARNING (continued)
vehicle control and an accident. Have your vehicle repaired imme·
diately by your authorized Audi dealer or a qualified workshop.
Drive slowly and avoid sudden, hard brake applications.•
Engine cooling system malfunction -L
A malfunction in the engine cooling system must be
repaired as soon as possible.
When the .J_ symbol in the display blinks, then either the
engine coolant
temperature is too high, or the coolant level
is too low. An additional driver message can also be displayed
by pressing the
[CHECK) button:
Switch off engine and check coolant level
-Pull off the road.
- Stop the vehicle.
- Turn off the engine .
- Check coolant level~
page 305.
-Add coolant if necessary~ page 306.
-Continue driving only after the engine coolant
warning/indicator light goes out.
- Contact your authorized Audi dealer for assistance if
necessary.
If the engine coolant level is correct, then the radiator fan may be the
cause of the malfunction.
If the
D wa rning symbol (alternato r malfunction) also lights up on
the instrument panel~
page 29, then the fan belt may be damaged .
& WARNING
• If your vehicle should break down for mechanical or other
reasons, park at a safe distance from moving traffic, turn off the
engine and turn on the hazard warning lights~
page 68, "Emer­
gency flasher
A".
• Never open the hood if you see or hear steam or coolant
escaping from the engine compartment· you risk being scalded.
Wait until you can no longer see or hear steam or coolant
escaping.
• The engine compartment of any vehicle is a dangerous area.
Before you perform any work in the engine compartment, turn of
the engine and allow it to cool. Follow the warning stickers
~ page 286, "Engine compartment".
0 Note
Do not continue driving if the _f_ symbol illuminates. There is a
malfunction in the engine cooling system -you could damage your
engine .•
Engine oil pressure malfunction "l::,r:
The red engine oil pressure warning symbol requires
immediate service or repair. Driving with a low-oil-pres­
sure indication is likely to inflict severe damage to the
engine .
If the pressure is too low. An additional driver message can also be
displayed by pressing the
[CH ECK) button:
Switch off engine ! Oil pressure too low
Immediate actions
-Pull off the road .

-Stop the vehicle.
- Turn off the engine .
-Check the engine oil level with the dipstick~ page 301.
Dipstick readings checks too Low
-Top off oil to the proper level~ page 302.
- Make sure that the oil pressure warning symbol "e:7':
appears no longer in the display before you start driving
again.
Dipstick reading checks OK
If the oil pressure warning symbol "e:7': starts flashing
again even though the engine oil level checks
OK on the
dipstick ,
do not continue driving and do not let the
engine run in idle.
Instead , contact your authorized Audi
dealer for assistance.
W Tips
• The engine oil pressure symbol~ is not an indicator for a low
engine oil level. Do not rely on it. Instead, check the oil level in your
engine at regular intervals, preferably each time you refuel, and
always before going on a long trip.
• The yellow oil level warning indication requires oil refill or
workshop service without delay. Do not wait until the red oil pres­
sure warning ~ starts to flash before you respond to the low oil
level warning
:!:':! • By then, your engine may already have suffered
serious damage. •
Controls and equip ­
ment Safety first
Driver information display
Steering malfunction
i
If there is a malfunction in the electronic steering column lock, the steering cannot be unlocked.
If the i symbol in the display blinks, there is a malfunction
in the electronic steering column lock . An additional driver
message can also be displayed by pressing the[CHECK]
button :
Do not drive vehicle: steering defective
-Contact your nearest authorized Audi dealer or qualified
workshop .
- Do
not tow your vehicle.
& WARNING
Your vehicle must not be towed in the event of a malfunction in
the electronic steering column lock because it cannot be steered
due to the locked steering. If it is towed with the steering locked,
there is the risk of an accident. •
Ignition lock malfunction .Pe
A malfunction in the ignition lock must be repaired imme­
diately.
If the .Pe symbol in the display blinks, there is a malfunction
in the electronic ignition lock. An additional driver message
can also be displayed by pressing the [ CHECK] button:
Ignition lock defective. Contact workshop !
- Do not turn the engine off.
- Drive immediately to an authorized Audi dealer to have
the malfunction corrected . ..,
Vehicle care Technical data

Driver information displ ay
If there is a malfunction in the electronic ignition lock, the ign ition
cannot be turned off. Drive immediately to an authorized Aud i dealer
to have the cause of the malfunction corrected.
On vehicles with Convenience key*, the engine should not be switched
off using the
I STOP] button because the eng ine can not be started
again after the ignition is switched off. •
Yellow symbols
Ayellow symbol means WARNING.
Fig. 18 Display: low
f ue l leve l warn ing
(pr iority 2)
Yellow symbols indicate a priority 2 malfunction - Warning!
When a ye llow warning symbol appears,
one warning tone sounds. A
dr iver message appears as well to explain the ma lfunction in more
detail. The driver warning goes out after about 5 seconds, but it can
be brought up again at any time by pressing the
I CHECK] button .
Check the displayed function as soon as possible. If
more than one
priority 2 malfunction is detected, all symbo ls will appear one after
the other for about 2 seconds.
Yellow symbols mean: Convenience key*
=>page
129
Key not in vehicle
USA models : =>page24
Defective brake light
Can ada mod els: => page24
Defect ive b rake light
Defective light bulb
=>poge24
Light/rain sensor defective* =>page33
Windshield washer fluid =>page33
level low
L ow fue l level
=>page33
Refill Ad Blue* =>page292
Battery voltage =>page33
Worn brake pads =>page34
Dynamic headlight range = page34
contro l defective
II Check engine oil level
=>poge34
-
Engine o il sensor malfunction =>page 34
II Engine speed limitation* =page34
-
Diesel part icu late filter* =>page35
clogged
-Adaptive Light* defective => poge35 ..

Ignition loc k malfunction ~page35
liWindshield wiper d efective ~page35
-
T ire pressure monitoring sys-~ page334
tern
Loss of a ir pressure
Tire pressure monitoring sys-
~page334
tern System not available
-
Battery in remote contro l key ~page42
Automatic transmission mal-~page 166
function
Applies to vehicles: w ith Con venience key
Key not in vehicle
Key not in veh icle
Th is reminder appears along with the symbo l if the master key is
removed from the veh icle with the e ng ine runni ng . It is intended to
remind you (e.g. when changing drivers) not to continue the journey
without the master key.
If the master key is no longer in the ve hicle, you cannot sw itch off the
ignition after stopping the engine and you also cannot s tart the
eng ine aga in . What is more, you cannot lock the veh icle from the
outside. •
Applies to vehicles: with light and rain sens or
Light/rain sensor defective '
Automatic headlight s/ aut omatic wipers defective
Controls and equip ­
ment Safety first
•
Dri
ver information display
If the symbol illuminates, the light sensor has failed . For safety
reasons t he low be ams are tu rned o n permanent ly with the switch i n
AUTO . H owever, you can cont inue to turn the lights on and off using
the light switch. In the case of a defect in the rai n sensor, the wind­
shield wiper lever functions are still ava ilable. Have the light/rain
sensor checked as soon as possib le by an authorized Audi dealer .•
Windshield washer fluid level too low
Plea se refill washer fluid
If the symbo l il luminates, add wi ndshield was he r fluid to the washer
system and a lso to the headlight washer system~
page 312. •
Fuel supply too low
BJ Please refuel
Whe n th is symbo l ,. illum inates fo r the first time, the fue l rese rve in
your vehicle is still between 2 .6 and 3 .2 gallons (10-12 liters) . Refuel
as soon as possible~
page 289 .
If the symbol lights up, even when there is ample fuel in the tank, and
the text Tank system m alfunction ! Contact wo rkshop appears in the
display, the re is a fa ult in the system. Contact a q ualified wor kshop to
have the fault rectified. •
Battery voltage n
If the battery's state of charge is not in the optima l range, the.::)
symbol is show n in the display and the dr ive r message Low battery
cha rge: battery will be charged while dr iving appears.
Wh ile this dr ive r not ifica tion is displayed, you have to be prepared fo r
limited starting capability . ..,_
Vehicle care Technical data

Driver information display
Driver message appears and goes out again
If this dr iver message appears af ter the ignition is t urned on or w hile
dr iving and it goes out aga in afte r a while , the battery has been
adeq uate ly recharged.
Driver message appears and does not go out again
If t his dr iver no tifica tion appears after the ignition is turned on or
w hile dr iv in g and does not go out again , the battery's state of charge
is not in t he optima l range. Starting ca pability is restricte d. Have the
ba ttery checked by a n author ized A udi deale r as soon as possible .•
Worn brake pads U
J Brake pads !
If the warn ing light illum inates, immediate ly contact your a uthorized
Aud i dealer or qualified workshop to have all b rake pads inspe cted.
On USA mode ls the warn ing light
.:l comes on together w ith the
w ar ning light
BRAKE . Both sets of b rake pad s on an ax le mus t alway s
be rep laced at the same time.
& WARNING
Driving with bad brakes can c ause a collision and serious personal
injury.
• If the warning light and the warning light BRAKE1> with the
mes sage Brak e pads! comes on in the instrument cluster di splay,
immediately contact your authorized Audi dealer or qualified
workshop to have all brake pads checked or replaced if necessary. •
ll BRAKE: USA mo dels only
Headlight range control ~[)
, Headlight range control defective !
If the sym bo l i llum inat es , the dyn ami c he adlig ht range co nt rol is no
longer wo rking properly . H ave t he system ch ecked and repaired at
your aut horize d Au di dea ler. •
Engine oil level Please che ck oil level
W hen th e symbo l illuminates, check th e eng ine o il level as soo n as
possible =>
page 301. Top off the oil at yo ur earliest o pportunity
=>page 3 02. •
Engine oil sensor defective
Oil level ! Sensor defective
C
-
If the symbo l illuminates, contact your author ized Audi dealer and
h ave the o il sensor inspec ted . Unti l y ou have this d one, check t he oil
level each time you refue l just to be on the safe side=>
page 301 . •
A pplie s to v eh icl es: w ith eng in e s peed l imitat io n
Engine speed limitation .?i
!'"') Do not exceed max . engine speed of XXXX rpm
T he ; symbol illuminates when there is an engine con trol malfunc ­
tion. The indicator light • in t he instrument cl uster also illuminates.
T he eng ine speed is limi ted to the speed displaye d in the d river info r­
mation system . Keep in m ind that t he engine s peed will not exceed
th e v alu e disp laye d in th e d river infor mati on sy ste m, for examp le
w hen downshift ing. .,_

Please go to an authorized Audi dealer or other qualified workshop to
have the malfunction repaired .•
Appli es to ve hicl es : wit h diesel e ngine and di ese l part ic ulate filt e r
Diesel particulate filter clogged ii1-
Particulate filter See owner's manual
When the symbol illuminates, you can alter your driving sty le to
assist the filter self-cleaning process. Drive for approximately 15
minutes with the selector lever in the S position at a minimum speed
of 37 mph (60 km/h) and an engine speed of approximately 2,000
RPM. The temperature increase that will resu lt from th is can burn off
the soot in the filter. The symbol will switch off when the cleaning is
successful. After a successful cleaning, there is no need to bring the
car to an authorized dealer or qualified workshop because this is part
of normal vehicle operation .
If the symbo l does not switch off, see your authorized dealer or
other qualified workshop to have the problem co rrected.
For more information on the diesel particulate filter, refer to
:::>page 263.
& WARNING
Always adapt your speed to the current weather, road and traffic
conditions. You should never disobey traffic laws in order to
follow driving recommendations. •
Applies to veh icles: w it h A daptive light
Adaptive Light defective i :
t".J adaptive light defective
When this symbol illum inates, it means that Adaptive Light is
defective . Go to an au thorized dealership to have the headlights or
the control unit for the Adaptive Light repaired .•
Controls and equip ·
ment Safety first
Driver information display
Ignition Lock malfunction :;ie
If the
symbol in the display comes on, there is a malfunc·
tion in the electronic ignition lock. An additional driver
message can be displayed by pressing the
[CHECK] button:
Ignition lock defective
-Drive to an authorized Audi dealer or qualified workshop
at your earliest convenience to have the malfunction
corrected. •
Windshield wipers faulty<..:>
Windshield wiper defective
When this symbol illuminates, it means that the electronics for
the windsh ield wipers are defective . Please go to an author ized Aud i
dealer or qualified workshop to have the w indshield wiper system
repa ired. •
Speed warning system
Overview
The speed warning system helps you to keep your driving
speed below a set speed limit.
The speed wa rning system warns the driver if he exceeds a previously
stored max imum speed . A warning tone w ill sound as soon as the
vehicle speed exceeds the set speed by about 3 mph (3 km/h) . At the
same time, a warn ing symbol appears in the display.
Th e speed warning system has
two warning thresholds that function
independently of each other and that have somewhat different
purposes: .,_
Vehicle care Technical data