engine AUDI Q7 2011 Owner´s Manual

llft!I __ C_ h_ e_c _k _i _ n _g ~ a_n _d_ f_il _l_in _ g _________________________________________ _
& WARNING (conti nu ed )
• To avoid being burned, do not spill antifreeze or coolant on the
exhaust system or hot engine part s. Under certain condit ion s, the
ethylene glycol in engine coolant can catch fire.
0 Note
Do not add any type of radiator leak sealant to yo ur vehicle's engine
c oo lant. Addi ng radia tor repa ir fluid m ay adverse ly affe ct the func­
tion and performance of your cooling system and could result in
damage not cove red by y our New Vehicle Lim ited Warr anty. •
Adding coolant
Be very careful when adding engine coolant.
Before you check anyt hing in th e eng ine co mpart ment ,
always read and heed all WARNINGS => & in "Wor king i n
t h e e ngine compa rtment" on
page 301.
- Tur n off the eng ine.
- Let t he engi ne c ool d ow n.
- Place a thic k rag over th e coolan t expans ion tank
=> pag e 309, fi g. 237 and carefully twist t he cap cou nter ­
cl ockwi se
=> &.
- Add coo lant.
- Tw ist the ca p on aga in
tightly .
Replacement eng ine coolant must conform to exact specifications
=>
page 308, "Coolant". Even in a n emergency, if coolant addi tive
Gl2 ++, Gl2 + or Gl2 is not available, do not use a different addit ive.
Use plain wate r in st ead until you can get the cor rec t additive an d can
restore the correct ratio. This shou ld be done as soon as possible. If
you have lost a considerable amount of coolant, then you sho uld
a d d c old an tifr ee ze and cold wa ter only when the e ngine is cold.
Always use
new engine coo la nt when refilling.
Do not fill coolant above the "MAX" mark. Excess coolant will be
fo rced o ut thr ough the p re ssur e relief v alve in the c ap w hen the
eng ine becomes hot.
& WARNING
• The cooling system is under pressure and can get very hot.
Reduce the risk of scalding from hot coolant by following these
steps.
-Turn off the engine and allow it to cool down.
- Protect your face , hands and arms from escaping fluid and
s team by covering the cap with a large, thi ck rag .
- Turn the cap slowly and very carefully
in a counter-clockwise
direction while applying light, downward pre ssure on the top
of the cap.
- To avoid being burned, do not spill antifreeze or coolant on
the exh aust system or hot engine parts . Under certain condi­
tions , the ethylene glycol in engine coolant can catch fire.
• Antifreeze is poisonous. Always store antifreeze in its original
container and well out of the reach of children.
• If you drain the coolant , it mu st be caught and safely stored in
a proper container clearly marked "poison ".
0 Note
• Coolant poll utes the environment and could cause an engine fire.
Excess coolant w ill be forced o ut thro ugh the pressure relief va lve in
t he c ap when t he e ngine becomes hot.
• If, i n an emergency, only water can be added, the co rrect ratio
between wate r and an tifreeze=>
page 308 mus t be res to red as soo n
as possib le. _..

Checking and filling -
------------- ------=------=:;______,.J,,...
<£> For the sake of the environment
Drained coolant sho uld not be reused. A lways dispose of used coolan t
w hile observing a ll enviro nmental regulations .•
Radiator fan
The radia tor fa n switc hes on a utoma tically by itself
The radiator fan is driven by the engine via the V-belt. The v iscous
cl utch reg ulates the spee d of t he fan accord ing to t he tem pera ture o f
the coolant.
An aux ili ar y e lec tric r adi ator fan* sw itches on and o ff depend ing o n
coo la nt temperat ure and other vehicle operating conditions.
After you switch the engine off, the auxiliary fan can continue r unning
for up to 10 minutes -eve n w it h t he igni tion o ff.
It can even swit ch on
again later by itse lf => & , if
• t he tem pera ture of the e ngi ne coola nt rises due to the hea t build­
up from the eng ine in the engine compa rtment, o r
• th e engine compar tmen t heats up because the ve hicl e is parked in
intense s unlight.
& WARNING
• To reduce the risk of personal injury never touch the radiator
fan .
• The auxiliary electric fan is temperature cont rolled and can
switch on suddenly even when the engine i s not running.
• The auxiliary radiator fan switche s on automatically when the
engine coolant reaches a certain temperatu re and will continue to
run until the coolant temperature drops. •
Vehicle OP-eration
Brake fluid
Checking brake fluid level
The brake flu id l eve l can be checke d with a quick gl ance .
Fig . 238 E ngine
compa rtment : Brake
fluid rese rvoir
Before you check a nyt hin g i n th e eng ine compa rtment ,
always read and heed all WARNINGS=> & in " Working in
the e ng ine compartmen t" on
page 301 .
-Read the brake fluid level from t he bra ke flu id reservoir
=> fig. 238 . T he bra ke fluid leve l must be between the
" MIN " and "MAX" markings.
Th e brake fl uid rese rvoir is located at the rear partition of t he engine
compartment on the left side=>
page 302.
The fluid level may drop slightly after some time due to the auto­
m atic adjus tment o f th e brake pads. This is no t ca use for alarm .
If the brake fluid level falls
considerably below the "MIN" mark, t he
brake warn ing/i nd icator lig ht ( U.S. models :
BRAKE, Canadian mode ls:
ill ) will come on=> page 20 and=> page 34. Do not continue to
operate the vehicle . The complete brake system s hould be thorough ly
che cked by an au thori zed Aud i dea le r o r q ua lified wor kshop a nd the
cause corrected.
If t h e brake fl uid leve l is too low, the brake .,,_
Vehicle care Do-it-yourselt service iTechnical data

___ C_ h_ e_c _k _i _ n _g ~ a_n _d_ f_il _l_in _ g _________________________________________ _
& WARNING (conti nu ed )
• Always wear eye protection. Do not let battery acid or any lead
particles get on your skin or clothing. Shield your eyes. Explo sive
gases can cause blindness or other injury.
• Battery acid contains sulfuric acid. Sulfuric acid can cause
blindnes s and severe burns .
- Always wear gloves and eye protect ion. Do not tilt the
battery because acid could leak out of the ventilation open­
ings.
- If you get battery acid in your eyes or on your skin , immedi­
atel y rinse with cold water for several minutes and get medical
attention.
- If you should ingest any battery acid, seek medical attention
immediately.
• Do not expose the battery to an open flame, elect ric sparks or
an open light .
• Do not smoke.
• Do not int erchange the positive and negative cab les .
• When working on the battery, be sure not to short-cir cuit the
terminals with tools or other metal obje cts. This would cause the
battery to heat up very quickly, which could lead to damage or
explosion and per sonal injury .
• When a battery is charged , it produces hydrogen gas which i s
e xplosive and could cause personal injury.
• Always keep the battery well out of the reach of children .
• Before work is done on the electrical system, disconnect the
negative ground cable.
• Befo re performing any work on the electrical system , swit ch
off the engine and ignition as well as any electrical equipment .
The negative cable on the battery must be disconnected. If you are
ju st going to replace a light bulb, then it is enough to switch off
the l ights.
& W ARNING (continued )
• Before di sconnecting the battery , switch off the anti-theft
alarm system! Otherwise you w ill set off the alarm .
• When disconnecting the battery, first disconnect the negative
cable and then the po sitive cable .
• Before reconnecting the battery , make su re all electri cal
consumers are sw itched off . Reconnect the positive cable first and
then the negative cable. Never interchange the cables - this could start a fire!
• Never charge a frozen or a thawed-out battery. It could
e x plode! If a battery has frozen, then it must be replaced. A
di scharged battery can freeze o ver at 32 °F (0 °C ).
• Make sure the vent hose is always attached to the open ing on
the side of the battery .
• Never use batte ries which are damaged . There is the danger of
an explosion! Alway s repla ce a damaged battery .
& WARNING
California Proposition 65 Warning:
• Battery posts , terminals and related accessorie s contain lead
and lead compounds, chemicals known to the State of California
to cause cancer and reproductive problems. Wash hands after
handling.
0 Note
• Do not disco nne ct the vehi cle battery when t he ign it ion is
switched on o r when the engine is running, otherwise, you wi ll
da mage e le ctronic compone nts in t he e lec trica l system .
• If your ve hicle is go ing to stan d for a long period of time witho ut
bei ng d rive n, protect the ba tte ry from "freezing", ot herwis e it w ill be
damaged and will then have to be replaced.•

Checking and filling Ill
-------------------=------=:;______,.J
Battery charging
Starting the engine requires a well charged battery.
Fig. 239 E ngine
compar tmen t: Connec ­
t ors fo r cha rger and
j umper cables
Alwa ys read and h eed all WARNINGS below=> & and => &
in "Working on the battery" on page 313 .
- Turn off the ignition and all electrical consumers.
- Make sure the area is well ventilated when you charge the
battery.
- Open the hood :::::,
page 300.
-Open the red cover on the positive pole=> fig . 239 .
- Connect the charger connectors acco rding to the instruc-
tions to the
jump start bolts . (Bolts under the red cover=
"positive", Bo lts with hex head
= "negative") .
- Only now plug the mains lead for the charging equipment into th e wall outl et and turn it on=>
&-
- Make sure the charg ing rate is not over 30 amps /14.8
Volt.
- When the battery is fully charged: Turn the charging
equipment off and remove the ma ins lead from the wall
outlet.
Vehicle OP-eration
-Now remove the clamps for the charging equipment.
- Close the red cover on the positive pole.
- Close the hood :::::,
page 301.
A discharged battery can freeze at temperatures of only O 0C. Allow a
frozen battery to thaw completely before attempting to charge it
~ & .However, we recommend not using a thawed battery again
because the battery casing can be cracked due to ice format ion and
can leak battery acid.
Battery charging (Ma xim um cha rging rate of 30
am ps/ 14.8 Vol t)
When charging at low voltages (e.g. with a tric kle c harger ), the
battery cables do not have to be disconnected first . The battery caps
sho uld
not be opened when ch arging a battery.
It is not necessary to remove the battery from the luggage com part·
ment.
F a st charging the batter y (chargin g rate above 14.8
Volt s)
For technical reasons do not use a battery charger that uses voltage
greater than 14.8 Volts to charge your vehicle's battery.
& WARNING
Charging a batt ery can be dan ger ou s.
• Alwa ys foll ow the ope rating in str uc tion s provi ded b y the
batt ery c harger manuf acturer when charging your battery .
• Never char ge a frozen battery. It ma y explode be cause of ga s
trapped in the i ce. Allow a fr ozen battery to thaw out first .
• Do not reu se batterie s wh ich were fr ozen . The batter y hou sing
m ay ha ve crack ed and w eaken ed when th e batt ery froz e.
• Charge the b attery
in a well ventilated area . Keep away from
op en flame o r el ect rica l spark. Do not sm oke . Hydrog en gas gener -
ated by the b attery is ex plosi ve. •
Vehicle care Do-it-yourselt service Technical data

•--=C:.:.h.:.. e=. c=.:..:: k .:.:in ..:. g ~ a::..:..: n~d .:...:.. f:....:il ..:.li :.:.n.;.: g~ ------------------------------------------
& WARNING (continued)
• To reduce the danger of explosion, never connect or disconnect
charger cables while the charger is operating.
• Fast charging a battery is dangerous and should only be
attempted by a competent technician with the proper equipment.
• Battery acid that may spill during charging should be washed
off with a solution of warm water and baking soda to neutralize
the acid.
CD Note
Never use a fast charger as a booster to start the engine. This will seri­
ously damage sens it ive electronic components, such as control units,
relays, radio, etc ., as well as the battery charger.•
Battery replacement
The new battery must have the same specifications and
dimensions as the original equipment battery.
Intelligent energy management in your veh icle is responsible for
distributing the electrical energy throughout your vehicle
~ page 263. The intelligent energy management system will keep
the engine battery charged better then vehicles without this system .
To make sure the additional electrical energy is available once again
after you have changed the battery, we recommend that you install
batteries of the same type and manufacture only (the same as those
installed at the time your vehicle was delivered). Specifications are
listed on the battery housing. Your authorized dealer must code the
battery in the energy manageme nt system to enable you to use the
energy management functions correctly after replacing the battery.
If it is not possible to use a battery of this type, the new battery must
have the same capacity, voltage (12 volts), amperage, construction
and plug sea ling. When
installing the battery, make sure the ignition and all electrical
consumers are turned off.
CD Note
Make sure the vent ilation hose on the side of the battery is
connected, otherwise fumes or battery acid can leak out.
~ For the sake of the environment
Because of the prob lem of proper disposal of a battery, we recom­
mend your authorized Audi dealer change the battery for you.
Batteries contain sulfu ric acid and lead and must always be disposed
of properly in compliance w ith all environmental regulations.
Disposing of vehicle batteries imprope rly is very dangerous to the
environment. •
Windshield/headlight washer
container
Fig. 240 Engine
compartment: Wind­
shield and headlight*
wa sher fluid container
The washer fluid container is marked with the symbol Q on
its cap. .,

___________________________________________ C_ h_e _c _k_ i_n ~g_ a_n_ d_ f_ i_ll _i_n _g __ nn
- Before you check anything in the engine compartment ,
always read and h eed all WARNINGS ::::;, & in "Working
in the engine compartment" on
page 301 .
- Lift the filler cap tongue to add washer fluid. You can fill
the contai ner to the top .
- Press the cap back onto the filler neck after filling the container.
You can find the reservoir capacity in the table in~ page 365.
To prevent lime residue from building up on the spray jets, use
distilled water when refi lling. Always add a g lass cleaner so lution
(with frost protection in the winter).
0 Note
Do not mix engine coolant antifreeze or any other additives to fill up
the windsh ie ld washer rese rvo ir .•
Safety first Vehicle care Technical data

Tires and wheels -________________ f!ffl
If you wish to improve comfort when operating the vehicle at
normal load (up to 3 occupant s), you can adjust tire pres sures to
those specified for normal vehicle load . Before operating the
vehicle at maximum lo ad, you must increase the tire p res sures to
those specified for maximum vehicle load=>& .
Bear in mind that the tire press ure monitor ing system can only
mon itor the t ire pressu re s you h ave sto red . T he sys tem does no t
recogn ize the load cond it ion of your vehicle.
Th e effectiveness of t he tire pressu re monitoring system will be
impa ired if you store normal load pressu res but then operate the
vehicle at its maxim um loa d=> & . See the
illustration=> fig. 241 for the location of the label on driver's
side B- pillar (colo r of the act ual la bel and ex act l ocation on the
vehicle will vary slig htly).
N ote that the fo llow ing tab le is accurate at the time of going to press
and is subjec t to change. I n the even t of discrepancies , the tire pres­
sure label located on the dr iver's side B-pi llar a lways takes prece­
dence .
T he table below lists the recommended cold t ire inflation pressures
for the Audi model covered by your Owne r's Literature at t he ve hicle's
capac ity weight and the tire sizes insta lled on the respective models
as original equipment, or as a factory option .
Engine Tire designation Tire pressure front Tire pressure rear
(displace- normal load normal load
ment in
liter) condition
(up
full load condition (up
full load
to
3 occu- condition to 3 occu- condition
pants) pants)
PSI kPA PSI PSI kPA PSI kPA
255/55 R18 109H XL All Season
35 240 44 300
35 240 49 340
265
/50 R19 110H XL All Season 35 240 44
300 35 240 49 340
6-cylinder 275/45 R20 110H XL All Season 35 24 0 44 3 00 35 240 4 9 340
3.0/3.0 TDI
275 /45 R20 llOY XL High Performance 35 240
44 300
35 240 49 340
295
/35 R2110 7Y XL High Performance 36 250 44
300 35 240 49 340
XL= reinforced or extra load tire
. It may also appear as xl , EXTRA LOAD, or RF on the tire sidewall .
The correct tire p ress ure for t he spare wheel is loca ted on a labe l o n
the driver 's s ide B-pillar.
Beca use technical c hanges may be made to vehicle equipment dur ing
the model year, always compare the tire size des ignation on the t ire
pressu re labe l on yo ur vehicle with the t ires on your vehicle. Make
sure that the tire size informat ion on t he v ehicle labe l is the same as
the size of the t ires o n the vehicle. This is especially important if the
vehicle belo ngs to so meone else or you bo ug ht the vehicle with
Safety first
differe nt r im s/ tires or you bo ugh t the vehicle as a prev iously owned
vehicle.
Remember, yo ur safety and t hat of your passengers also depends o n
making sure that load limits are not exceeded. Vehicle load includes
everybody and everything in an d on the vehi cle. These load limits are
t e chnically refer red to as the veh icle's G ross Veh icle Weig ht Rating
("GVW R"). The Gross Axle Weight Rati ng ("GAWR") is the maximum
load tha t can be applied at ea ch of the ve hicle's two ax les . T he G ross ..
Vehicle care Technical data

_______________________________________________ W __ h_a _t_ d_o_ I_ d_o_ n_ o_ w_ ? _ __._
Release the two hook-and-loop fasteners, and remove the two
chocks . To use the chocks, you first have to raise the support plate
=>
page 340, fig . 250 (D and then insert the locking plate with the
two "tabs" into the elongated holes in the base plate @=>& .
& WARNING
• The chock cannot fulfil its function and may lose its stability if
the "tabs" on the support plate are not inserted correctly into the
elo ngated holes in the base plate. If this happens, the vehicle may
start to move while a wheel is being changed.
• Never use the folding chocks if they are damaged or if they
have not been assembled correctly.
& WARNING
Improper use of the vehicle jack can cause serious personal inju­
ries.
• Never use the jack supplied with your Audi on another vehicle,
particularly on a heavier one. The jack is only suitable for use on
the vehicle it came with.
• Using a bumper jack to raise the vehicle will damage the
bumper system. The jack may slip, causing injury.
• Never support your vehicle on cinder blocks, bricks or other
objects . These may not be able to support the load and could cause
injury when they fail.
• Never start or run the engine while the vehicle is supported by
the jack.
• If you must work under the vehicle, always use safety stands
specifically designed for this purpose.
• Always make sure the inflatable spare tire and even a flat tire
are secured in place and not loose, otherwise they could fly
forward, causing personal injury to passengers in the vehicle in an
accident or sudden maneuver. •
Vehicle OP-eration
Applies to vehicles : with bass box
Removing bass box
Before the inflatable spare tire can be taken out, the bass
box must be removed.
Fig. 251 Spare wheel
well: Bass box
Removing bass box
-Squeeze the locking tabs=> fig. 251 (D of the connector.
- Disconnect the connector @ and place the lead to one
side.
- Turn the large screw counter-clockwise.
- Carefully remove the bass box.
Installing bass box
-Carefully place the bass box in the wheel. The inscription
"FRONT" on the bass box must face forward.
- Reconnect the connector that was removed.
- Secure the bass box with the large screw. •
Vehicle care Do-it-yourself service iTechnical data

1111.___W_ h_ a_t _ d_ o_ I_d_ o_ n_o _w_ ? ____________________________________________ _
-Block the diagonally opposite wheel with the folding
chocks or other objects.
- Take the
jack and the inflatable spare tire out of the
luggage compartment =>
page 340.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn
off the engine, turn the emergency flashers on and use other
warning devices to alert other motorists.
• Make sure that passengers wait
in a safe place away from the
vehicle and well away from the road and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed with the
folding chocks or other objects. When one front wheel is lifted off
the ground, placing the Automatic Transmission in "P" (Park) will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and
firm. If necessary, use a sturdy board under the jack.
• After installing the inflatable spare tire, make sure that you
replace the flat tire/wheel in its storage area properly and tighten
the knurled retaining screw securely. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and in exactly that order .
1. Activate the vehicle jack mode (only vehicles with Adaptive
Air Suspension) =>
page 182.
2. Remove the decorative wheel cover*. For more details see
also =>
page 345, "Decorative wheel covers" or
=>
page 345, "Wheels with wheel bolt caps".
3. Loosen the
wheel bolts=> page 346.
4. Locate the proper mounting point for the jack and align
the jack below that point=>
page 346.
5. Lift the car with the jack=> page 346.
6. Remove the wheel with the flat tire and then install the
inflatable spare tire=> page 348.
7. Tighten all wheel bolts lightly.
8.
Lower the veh icle with the jack .
9. Use the wheel bolt wrench and
firmly tighten all wheel
bolts =>
page 346.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode (only vehicles with
Adaptive Air Suspension)=>
page 182.
& WARNING
Always read and follow all WARNINGS and information:::::, & in
"Raising the vehicle" on
page 346 and => page 349. •
After changing a wheel
A wheel change is not complete without the doing the
following.
- Store and secure the wh eel you replaced in the spare
wheel well.
- Replace the tools and the jack in their proper location .

IIJII Fuses and bulbs ..._ __________________________________________ _
Bulbs
Replacing light bulbs
For your safety, we recommend that you have your autho­
rized Audi dealer replace burned out bulbs for you.
It is becoming increasing ly more and more d ifficult to replace vehicle
light bulbs since in many cases, other parts o f the car must fi rst be
removed before you are ab le to get to the bu lb . T his applies especially
to the light b ulbs in the front of yo ur car which yo u can only reac h
through the eng ine compartment .
Sheet meta l and bulb holders can have sharp edges that can ca use
serious c uts, and parts must be corre ct ly ta ke n apa rt and the n pro p­
erly put back together to he lp prevent breakage of parts and long
t erm damage from w ate r tha t can en ter housings th at have not been
properly resealed .
For your safety, we recommend that you have yo ur a uthorized Audi
dealer replace a ny bu lbs for you , since you r dealer has t he p roper
too ls, the correct bulbs and the expertise.
Ga s discharge lamp s (Xenon light s)* :
Due to the high electrical voltage, have the bulbs replaced by a qua l­
ified technician. Headlights w ith Xenon light can be ident ified by the
hig h voltage sticker .
& WARNING
Contact with high- voltage components of the electrical system
and improper repla cement of gas disc harge (Xenon) headlight
bulbs can cause serious personal injury and death .
• Xenon bulb s ar e pres surized and can explode when being
changed .
• Changing Xenon lamp s requires the special training, instruc ­
tions and equipment.
& WARNING (c on tinued )
• Only an authorized Audi dealer or other qualified work shop
s hould change the bu lbs in gas discharge lamps .
& WARNING
There are parts with sharp edges on the openings and on the bulb
holder s that can cause serious cuts .
• If you are uncertain about what to do , have the work
performed by an authorized Audi dealer or other qualified work­
shop . Serious personal injury may result from improperly
performed work .
[ i ] Tips
• If you mus t replace the lig ht bulbs yo ursel f, al ways remember
tha t the eng ine compartment of any vehicle is a hazardous area to
work in . Always rea d and heed all WARNINGS ~
page 290, "Engine
compartment"~ &,.
• It is bes t to ask your author ized Audi dea ler whe never you need to
change a bulb .•