engine AUDI Q7 2011 Owner´s Manual

Driving and environment
----------------------------------------------'
Driving and environment
The first 1,000 miles (1,500 km)
and afterwards
New engine
The engine needs to be run-in during the first 1,0 00 miles
(1,50 0 km) .
For the first 600 miles (1,000 kilometers):
- Do not use fu ll thrott le .
- Do not drive at engine speeds that are more than 2/3 of
the maximum permitted RPM .
From 600 to 1,000 miles (1 ,000 to 1 ,500
kilometers):
- Speeds can
gradually be increased to the maxim um
perm iss ible road or engine s peed .
During and after break-in period
- Do no t rev the eng ine up to high speeds when it is co ld.
T h is app lies w hether th e t ransmission is in N ( Neutral) o r
1 n gear .
After the break-in period - Do not exceed maximum engine speed under any circum ­
stances.
- U pshift i nto the nex t higher gear
before reach ing t he red
area at t he end of the tachometer scale==>
page 10.
Dur ing the first few hours of driving, the engine's interna l friction is
hig her than later w hen all the moving pa rts have been broken in. How
Controls and equip­ ment Safety first Vehicle operation we
ll th is b reak-in p rocess is done depends to a cons iderab le extent on
the way the veh icle is d riven dur ing the f irst 1,000 miles (1,500 kilo­
meters).
0 Note
E x tremely high e ngine speeds are automatic ally reduced. However,
these rpm limits are programmed for an engine well run- in, not a new
engi ne.
~ For the sake of the environment
Do no t dr ive with u nnecess arily hig h engine speeds -upshift ing early
saves f uel, reduces noise and protects the environme nt.•
New tires
If y our veh icle is run nin g on n ew tir es, dr ive parti cula rl y
carefu l for the fi rst 35 0 mil es (500 kil ometer s) af ter fit ting.
& WARNING
New tires tend to be slippery and must also be "broken -in ". Be
sure to remember this dur ing the first 350 miles (500 kilome ­
ter s) . Brake gently. Avoid following closely behind other vehicles
or other situations that might require sudden, hard braking.
u
New brake pads
Remember tha t new brak e pa ds d o no t hav e a fu ll braki ng
eff ect d uri ng the first 250 mi les (400 k ilomet ers) after they
are i nsta lled.
Vehicle care Do-it-yourself service Technical data

Driving and environment
New brake pads have to be "burnished in" before they have optimal
grab ~& .
Dur ing the break-in period, you should avoid putting severe loads on
the bra kes. Severe loads incl ude, for example, sudden hard braking,
in part icu lar at very high speeds or, for examp le, on mountain passes .
& WARNING
New brake pads don't have the be st stopping power and must be
" b roken-in " du ring the initial 100 to 150 miles (150 to 200 kilo­
meters ) of normal city driving . You can compensate for this by
pressing the brake pedal more firml y. This also applies later when
new pad s are installed.
'1
Ap plies to veh icles : w it h gasoline eng ine
Catalyt·c converter
It is very important tha t your emission con trol system
(catalytic c onverte r) is f unctioning properly to ensure
that your vehicle is running in an environmentally sound
manner.
- Always use lead-free gasoline~ page 291, "Gasoline" .
- Never ru n the tan k down a ll the way to empty .
- Nev er put to o mu ch mot or oil in y our engin e~
pag e 306,
"Add ing engin e oil~" -
- Neve r try to push -or tow-start yo ur vehicle .
The catalytic converter is an efficient "clean-up" dev ice built into the
exhaust system of the ve hicle. The catalytic converter burns many of
the pollutants in the exhaust gas before they are released into the
atmosphere. The exclusive
use of unleaded fuel is critically important for the life of
t he c atal ytic converte r and proper f unct ion in g of t he engi ne.
& WARNING
• Do not park or operate the vehicle in areas where the hot
e x haust system may come in contact with dry grass , brush , fuel
s pill or other material whi ch can cau se a fire.
• Do not apply additional undercoating or rustp roofing on or
near the exhau st manifold, exhaust pipe s, catalytic converter or
heat shields. During driving , the substance used for undercoating
c ould overheat and cau se a fire .
0 Note
• Be aware th at just one tank fi lling wit h le aded fu el w ill alre ady
ser iously degrade the performance of the catalytic co nverter.
• Do not excee d the correct engine oil leve l~
page 306.
• Do not drive unti l the f uel tank becomes complete ly empty . The
eng ine could misfire. Unbu rned fuel could also ge t into the exha ust
system and th is could cause the catalytic converter to overheat.
• Do not tu rn off the igni tion whi le the veh icle is moving .
• Do not contin ue to operate your vehicle under these conditions, as
o therwise fuel can reach the cata lytic converter . This could result in
overheating of the converte r, requiring its rep lacement.
• To assu re eff icient operat ion of the Emission Co ntrol System:
- Have yo ur vehicle main taine d pr operly and in a ccordan ce wi th
the service recommendations in your Warranty
& Maintenance
booklet .
- Lack of p roper maintenance as well as improper use of the
veh icle w ill imp air the f unction of the emiss io n con trol syste m and
could lead to damage. ..

• Driving and environment
------------------------------------------------'
ffi For the sake of the environment
Even when the Emission Control System is operating properly, the
exhaust gas can have a sulfur-like exhaust gas smell under some
operat ing states. This depends on the sulfur content of the fue l being
used. Using a different brand of fuel may help, or filling the tank with
lead-free supe r grade gasoline. •
Applies to vehicles: with d iesel engine
Diesel particulate filter
The diesel particulate filter filters nearly all of the soot particles out
of the exhaust. The filter cleans itself automatica lly under norma l
driving conditions. If the filter cannot clean itself (for example,
because you are only driving short distances), the fi lter becomes
clogged with soot and the symbol for the diesel particulate filter
illuminates ~
page 40.
& WARNING
• Do not park your vehicle over flammable materials such as
grass or leaves because the high temperature of the diesel partic­
ulate filter could start a fire.
• Do not apply an underbody protectant in the exhaust system
area or a fire could start. •
Avoid damaging the vehicle
When you are driving on poor roads, or over curbs, steep ramps, etc.,
make certain that low-lying parts such as spoilers and exhaust system
parts do not bottom out and get damaged.
Thi s is espec ially true for vehicles with low-slung chassis (sports
chassis)" and fully loaded vehicles. •
Controls and equip­
ment Safety first Vehicle operation
Operate your vehicle economically
and minimize pollution
General
Your personal
style of driving will determine the economy
of your vehicle, as well as exhaust and noise levels.
Fuel economy, environmental impact, and wear on your engine,
brakes and tires largely depend on three factors:
• your personal dr iv ing style
• operating conditions
• technical limitations
If you anticipate what you need to do next and drive economically,
you can easily cut your fuel consumption by 10-15 percent. This
section will give you some tips on how you can he lp the environment
and your pocketbook.
(I) Tips
The consumption est imates as published by ENVIRONMENTAL
PROTECTION AGENCY (EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, which will vary
depending upon vehicle load and speed, road and weather conditions,
trip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are accelerating.
-Avoid unnecessary accelerating and braking.
Vehicles use the most fuel when they are accelerating . If you antici­
pate what is going to happen next, you will need to brake less and,
thus, accelerate less. Let the vehicle coast whenever possible - for
example when you see that the next traffic light is red. •
Vehicle care Do-it-yourself service Technical data

Driving and environment
Avoid full throttle
Driving at moderate speeds saves fuel and improves your
mileage.
-Try and keep well below your car's maximum speed.
Accelerating gently reduces fuel consumption, engine wear, and does
not disturb the environment.
Fuel consumption , exhaust emiss ions and eng ine no ise increase
disproportionately at high speeds . If you drive at approximately three
quarte rs of top speed, fuel consumption will be reduced by one ha lf.
Never drive faster than the posted speed limit and weather condi­
tions permit. •
Reducing unnecessary idling
Even when your car is just idling it burns up fuel.
- Shut the engine off when you are not driving the vehicle.
- Do not warm up the vehicle by letting the engine run at
idle .
It makes sense to shut off the engine in traffic jams, when waiting for
trains to pass at railroad crossings , or at traffic lights that have long
waits on red. Turning the engine off for just 30-40 seconds saves
more fuel than is burned starting the engine aga in.
It takes a long time for the engine to warm up fully when it is running
at idle . However, wea r and noxious emiss ions are especially high
when the engine is warming up. So you should drive away as soon as
you start the engine and avoid running at high rpms while the engine
is still warming up .
0 Note
Do not leave engine idling unattended after starting. If warning
lights should come on to indicate improper operation, they would go
unheeded. Extended idling also produces heat, which could result in
ove rheating or other damage to the vehicle or other property. •
Regular maintenance
A badly tuned engine unnecessarily wastes a lot of fuel .
-Have your vehicle serviced at regular intervals .
By having your vehicle regularly serv iced by an authorized Aud i dealer
helps to ensure that it runs properly and economically. The condition
of your vehicle not only affects its safety and ability to hold its value,
it a lso affects
fuel consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine load and speed .
It is norma l for the oil consumption of a new engine to reach its
lowest value after a certain mileage has been d riven.
You must drive your vehicle about 3,000 miles (5,000 kilometers) befo re you can properly assess oi l consumption.
This also app lies to fuel consumption and engine output .
0 Note
• Have your veh icle ma inta ined properly and in accordance w ith the
service recommendations in your Warranty
& Maintenance booklet.
Lack of proper maintenance as well as im proper use of the vehicle will
impair the function of the emission control system and could lead to
damage .
• Do not alter or remove any component of the Emission Control
System un less approved by the manufacturer. ._

Driving and environment
------------------------------------------------'
• Do not alter or remove any device, such as heat shields, switches,
ign ition w ires, valves, which are designed to protect your vehicle 's
Emission Control System and other important vehicle components. •
Fewer short trips
Fuel consumption will always be relatively high on short
trips.
- Try to avoid driving short distances with a cold engine.
The engine and catalytic converter have to reach their optima l oper­
ating temperature
to reduce fuel consumption and noxious emis­
sions effectively.
Just after starting, a cold engine in a mid-size car only achieves a fuel economy of 6-8 miles per gallon (30-40 l/l00km). After about a half
a mile, fuel economy climbs to 12 mpg (20 l/100 km) . After about
2.5 mi les (4 km), the engine is at its proper operating temperature
and fue l economy has reached a normal level. So you can see that you
should avoid short trips whenever possible.
Th e
outside temperature is also critical in this regard. Your car
consumes more fuel in the winter than in the summer. •
Controls and equip­
ment Safety first Vehicle operation
Vehicle care Do-it-yourself service Technical data

Driving off road
------------------------------------------------------'
vary. It is the driver's responsibility to decide whether a vehicle can
overcome a specific situation
=> &-
Gradient angle
The number of meters in altitude gained over a distance of 109 .4
yards or 100 meters (grade) are given as a percentage or degrees.
Information about the gradient the vehicle can climb under its own
power (depends in part on the road surface and engine power).
Maximum permitted grade: 31
°
Lateral angle (slope of vehicle)
Indicates the angle up to which the vehicl e can be driven diagonally
or across the fall line on a slope without the vehicle tipping over s ide­
ways (depends on center of gravity). Maximum permitted late ral
angle: 35°
Breakover angle
Indicates the angle up to which the vehicle can dr ive over a ramp at
low speed without the underside of the vehicle hitting the edge of the
ramp.
• Vehicles without air springs: maximum breakove r angle: 21, 1 °
• Vehicles with adaptive air suspension*: maximum breakover
ang le: 23.8° (at high level 2)
Approach /departure angle
Transition from the horizontal plane to a gradient or from a grade
back to level ground. Indicates the angle up to which the vehicle can
drive onto or off a slope at low speed without striking the bumper or
the underbody.
• Vehicles without air springs: maximum approach/departure
ang le: 21.0° (front), 23.4° (rear)
• Vehicles with adaptive air suspension*: maximum
approach/departure angle at high level 2: (front) 23,5°, (rear) 25 .4°
Controls and equip­
ment Safety first Vehicle operation
Ground clearance
Th
e distance between the road surface and the lowest point of the
vehicle underbody.
• Vehicles without air springs: ground clearance: 8.1 in
(204 .8 mm)
• Vehicles with adaptive air suspension*: maximum ground clear­
ance: 9.4 in (239.8 mm) at high leve l 2
& WARNING
Exceeding the stated maximum figures can result in severe inju­
ries or vehicle damage.
• All the information was gathered on level, firm and non-slip­
pery road surfaces, and under dry weather conditions.
• Ideal conditions do not prevail offroad. Never utilize the
maximum readings to their fullest, always leave a safety
reserve.
u
Driving tips
On poor road and off road, there is always only one
motto: Plan ahead and drive slowly!
Please observe the following when driving away from paved
roads:
- Drive only on roads and offroad sections which match the
design of your vehicle and your abilities as a driver. Never
take risks!
- Drive slowly and plan ahead!
- Take into consideration the
ground clearance of your
vehicle .
- Activate the
ESP offroad mode~ page 256 as needed.
Vehicle care Do-it-yourself service Technical data

Driving off road
- Use the hill descent control~ page 257 when dr iving
down steep sections on hills .
Unpaved roads and offroad
Drive slowly on unfamiliar roads and unknown offroad sections, and
loo k ou t for unexpec ted obsta cles (e.g. potho les, rocks, t ree st umps,
etc.).
T o prevent the vehicle from bottoming and avoid damage to the
unde rbody, you should d rive st raight ac ross severe b umps in the
ground with on ly one s ide of the vehicle so that on ly two of your
w heels cross the bumps.
Drive brisk ly throug h sandy or marshy offroad sections and do not
stop, if at all possible.
Driv ing th rough water
N ote the following to avoid vehicle dam age when driving throug h
water, for example on flooded roads:
• T he wate r must not be any higher than the bottom of the ve hicle
body .
• Do not drive faste r th an wal king speed .
Driving on a slope
If yo u ever find you rsel f not able to climb a slope, do not t ry to turn
around, drive back down in
re verse . Otherw ise, you run t he risk of
t ipping over .
If the vehicle threatens to t ip over when driving across a slope, you
must immediately steer downhill in the direction of the slope.
Do not park yo ur vehicle o n steep s lopes o r gr ad es.
To red uce the risk of tipp ing over, drive on s lopes in the di rect io n of
t he downward slo pe (fa ll line) -
not crosswi se .
Driv ing on snow-covered ground
T he s tandard tires fi tted to yo ur vehi cle are not snow t ires. So yo u
should mount wheels with snow t ires in good t ime where winter road
conditions p revail. Befo re dr iv ing on unp lowed stretches o f deep snow, install tire chains
. For tech nica l reasons, t ire chains may only
be ins talle d on the re a r wheels -never on the front whee ls.
& WARNING
After driving through water , mud, slush, etc. , the brakes may be
slow to take effect because of wet brake rotors and pads.
Dry the
brake s first by braking carefully to re store the full braking effe ct.
0 Note
Vehicle components such as the engine, trans mission, s uspension or
electrical system can be severely damaged by dr iv ing through water.
(I) Tips
• Check the dept h of the water before dr iv in g through it.
• Do not stop the vehicle, dr ive in reverse or sw itch the e ngine off
when driving through water.
• K eep in m ind th at on coming vehicles m ay cre ate w aves t hat ra ise
the water level and make it too deep for your vehicle to drive through
safe ly.
• Avoid dr iving through sa lt water because it ca n cause corrosion .•

Trailer towing
~-----------------------------------------
& WARNING (cont inued)
• The Gro ss Vehicle Weight Rating for your Audi Q7 vehicle,
found on the safety compliance label on the driver's side B-pillar, must never be exceeded under any circumstances . Exceeding the
Gross Vehicle Weight Rating of your vehicle is likely to damage
your vehicle, and such damage will not be covered by your Limited
New Vehicle Warranty. Exceeding the Gross Vehicle Weight
Rating will also change the performance and handling character­
istics of your vehicle, whi ch could cause a crash resulting in serious
injury or death.
• The Gro ss Vehicle Weight Rating for your Audi Q7 would be
exceeded if your vehicle is simultaneously equipped with
Panoramic sliding sunroof; third-row seating ; trailer towing
equipment (factory or dealer-installed ), and running boards
(dealer-installed) . UNDER NO CIRCUMSTANCES MAY ALL SUCH
ITEMS BE INSTALLED ON THE SAME VEHICLE .•
Operating instructions
M AX 6 .9"
MA X
175mm
Trailer towing weights
Fig. 223 Permitted
ball position of the
tra iler hit ch
With a factory -installed tra ile r hi tch, the maximum pe rmissib le
t ra iler weig ht is 6,615 lbs (3,000 kg). The maximum pe rmissib le
unbraked trailer we igh t is 1,650 lbs (750 kg) . With an
aftermarket
trail er hi tch, the m axi mum permissibl e traile r weig ht i s 5,5 12 lbs (2,500
kg) . These specifications app ly when driv ing on roads havi ng
an in cline o f less t han 12%.
Permissible tongue load
For best ve hicle handl ing un der t hese ch ange d co ndition s, adju st the
tra ile r l oad so that the tongue load is at the maxim um a llowab le or
sligh tly lower. You can get an app roxim atio n of the tongue load w it h
a bat hroom scale or you ca n measure the load at a t ruc king company
or we ighing st ation.
W it h a
factory-installed trailer h itch, the max imum pe rmissible load
on t he ba ll hitc h may not exceed 662 lbs (300 kg). W it h an
after­
market
tra ile r hi tc h, t he ma ximum pe rm issi ble loa d on the b all hi tch
may not exceed 551 lbs (250 kg). It is recommended to use the
maxim um permi ssible loa d.
Trailer load distribution
Be su re the load in t he tra ile r i s held se curely in p lace to p revent it
from shi fting forward, backwa rd or sideways.
Never allow a passenger to ride in a trailer=> & in "Dr ivin g in struc­
t ions" on
page 275.
Ball mount
The tra ile r hitch may on ly be used w ith suitable ball mount and ball
=> fi g. 223 . Ins tallat ion of the hi tch b all mus t be c arrie d out in acco r­
dance with the manufacturer's instructions . At the height d imension
of 1. 5 in (38 .5 mm) a toler ance of+/- 0.5 in ( 12. 7 mm ) is per miss ible
Engine cooling system
Towing a trailer makes t he eng ine work harder. It is impo rtant that
t he cooling system 's performan ce is up to the addi tional loa d. Mak e
sure that the coo ling system has enough fluid .
Tire pressure
When towing a trailer, inf late the tires ofyourvehicle to the cold tire
pre ssure listed unde r "Full lo ad" on t he tire pre ssu re lab el. Th e tire ...

pressure label is located o n the dr iver's side B-pillar. Inflate trailer
t ires to tra ile r and t ire ma nufacturers' spec ifications.
Lights
T he headl ight settings shou ld be chec ked with the tr ailer attached
before driving off. Check to make sure both vehicle and trailer lights
are wo rking properly.
Safety chains
Be sure tra ile r safety cha ins are p roperly connected from the t rai ler
to the hitch on the vehicle. Leave enough slack in the chains to perm it
tu rning corners . When you install sa fe ty ch ains, ma ke sure they will
not drag on the road when you are driving.
T he chains should cross under the trai ler tongue to prevent it from
dropping in case of separation from the h itch .
0 Note
If you are goi ng to tow a trai ler , you must activate the trai ler opera­
tion mode =>
page 182, "Towing a trailer". •
Driving instructior,s
Driving with a trailer always requires e xtra care and
consideration.
To obtain the best possib le handling of ve hicle a nd trailer ,
please note the following :
- Do not tow a loaded trailer when your car itself is not
loaded.
- Be especia lly careful when pass ing other vehicles .
- Observe speed limi ts.
- Do not drive at the maximum pe rmissible speed.
Controls and equip­
ment Safety first Vehicle operation
- Always apply brakes early.
- Mo
nitor the temperature gauge.
Weight distri but ion
T owing a loaded trailer with an empty car results in a highly unstable
distribution of we ight . If t his cannot be avoided , drive at very low
speeds only to avoid the risk of losing steering control.
A "balanced" rig is easier to operate and control. This means that the
tow veh icle shou ld be loaded to the extent poss ible and permissib le,
wh ile keeping the tra ile r as lig ht as poss ible unde r the ci rc u mstances.
Whe never possible, transfer some cargo to the luggage compart ­
me nt o f the tow vehicle while observing tongue load requirements
and vehicle loading considerations.
Speed
The higher the speed, the more d ifficult it becomes for the driver to
control the r ig . Do not dr ive at the maxim um permiss ible speed .
Reduce your speed eve n more if load, weather or w ind conditions are
unfavorable -particular ly when going downhill.
Reduce vehicle speed
immed iately if the tra ile r shows the slightest
sign of swaying.
Do not tr y to stop the s wayi ng by a ccele rating .
Observe speed lim its. In some areas, speeds for veh icles towing
trailers are lowe r than for regular veh icles .
Always apply brakes early. When driving downhi ll, shift into a lower
gear to use the engine brak ing effect to slow t he ve hicle . Use of the
brakes alone can cause them to overheat and fa il.
Coolant temperatur e
The coo lant temperature gauge=> page 10 must be observed care­
fu lly. If the needle moves close to the upper end of the sca le, reduce
speed immediately and/or turn off the air conditioner.
If the coo lant temperature warning light in the instrument clus ter
starts flash ing
- F- , pull off the road, stop and let the engine idle for
about two m inutes to prevent hea t buil d-up.
Vehicle care Do-it-yourself service Technical data

Trailer towing
"---------------------------------------------------
in. WARNING
Anyone not properly restrained in a moving vehicle is at a much
greater risk in an a ccident . Never let an yone ride in y our car who i s
not prop erly wearing the re straints provided by Audi. •
Trailer towing tips
Important to know
Your vehicle handles differe ntly when tow ing a tra iler because of the
additiona l weight and different we ight distribution. Safety, perfor­
man ce and economy w ill greatly depend on how ca refu lly yo u load
your trailer and operate your rig.
Be fore you actua lly tow your tra ile r, prac tice turning, stopp ing and
back ing u p in a n area away from traffic. Keep pract ic in g until you have
become completely familiar with the way your vehicle -trailer combi­
nation behaves and responds .
Backing up is diff icult and requ ires pract ice. Backing up w ith a trailer
gene rally requires s teer ing a ction opposi te to th at when ba cki ng up
your vehicle witho ut a trailer.
Maintain a greate r d istance between your ve hicl e and the one in front
of yo u. You will need more room to stop . T o compensate fo r the
trai ler, you will need a larger than normal turning radius .
W hen p assing, remember that you c annot acceler ate as fast as yo u
normally wou ld because of the added load. Make sure yo u have
enoug h room to pass. After passi ng, allow plen ty of room fo r yo ur
tra iler before changing lanes again .
Avoid jerky starts, sharp turns or rapid lane changes .
[ i ] Tips
• Do not tow a trai ler d uring the brea k-in perio d of your vehicle. •
If you tow a tra iler, your Aud i may require more frequent mai nte­
n an ce due to the ex tra load:::::>
page 368. •
Parking on a slope
Do not park on a slope with a trailer. If it cannot be
av oided, do so only after doing the following:
When parking:
- Apply the foot brak e.
- Have someone p lac e chocks un der bo th the vehicle and t he
traile r w he els .
- With c hoc ks i n place, slowly release the brakes u ntil the
wheel c hoc ks absorb t he load.
- Turn the w hee ls towards t he curb .
- A pply the parking brake.
- M ove th e selector le v er to
P.
When restarting after parking:
- A pply the foot brake .
- Start the engine .
- Mov e th e s elector lever to
D .
- Release the par king brake a nd s low ly pull o ut and away
fro m the w heel chocks.
- Stop a nd have someone retr ieve the w heel chocks .
(I) Tips
If you move the se lector lever of the a utomat ic t ransmiss ion to P
befo re applying t he par king br ake an d befo re blo cking the w heels, II-