wiper blades AUDI Q7 2011 Owner´s Manual

One-touch wiping
- Move the lever to position@, when you want to wipe the
windshield
briefly.
Automatic wiper /washer
- Pull the lever to position © (toward the steeri ng w heel)
and hold .
- Re lease the lever. The washer stop s and t he wip ers keep
going for about four seconds . Depending on how long the
lever is held, d ifferent numbers of was h cyc les are
performed.
Turning off the wipers
- Move the lever back to positio n@ .
Gen eral information
The windshield wipers and the windshield washer system operate
only with the ign it ion on .
Dur ing a temporary stop, e.g. at a traff ic signa l, the set wipe speed is
automatica lly red uced by one stage.
Th e windshie ld washer noz zles a re heated at low tempe ratures when
the ignition is on .
Removing water droplets
About 5 seconds afte r the was h cycle is complete, the wipe r system
performs a single automat ic wipe cycle to remove any water droplets
that remain on the windshie ld w hile driving.
If you would like to deact ivate this delayed wipe cy cle w hile d riving,
you have to pull the lever to position ® aga in w it hi n 10 seconds after
this wipe cycle.
Water droplet removal is react ivated after the ign ition is sw itched off
and then on again.
Controls and equip ­
ment Safety first
Clear v
ision
W int er pos ition
T o speed up de -icing of the windshield wipers, they move to the
w inter position when the ig nitio n is switched off and at an outs ide
temperature below 39 °F (4 °C). In this position, the windshield
wipers a re in an a rea on the g lass which is reached by the air vents
below the g lass. It is also easier to remove snow and ice from the
windshield wipers in this position.
The w ipers leave the w inter pos it ion, when the ign it ion is switched
on, if the windshield wiper lever is oper ated or the active ra in sensor
reacts to moisture .
Rain sensor
The rain sensor operates on ly in the interval wiper position. When it
sta rts to rai n, the in terv al wiper mode is a ctivated a utomat ic al ly.
If the w indshield wipe r leve r is in the inte rval wipe position with the
ignition switched off, the rain sensor is not act ivated until vehicle
speed is above 4 mph (6 km/h) .
To reduce the sens itivity of the rain sensor, the switch © must be
moved down. To i ncrease t he se nsitivi ty of the ra in se nso r, the sw itch
must be moved up.
Th e higher the sensitivity setting, the sooner the windshie ld wipers
react to mo isture on the windshie ld . Increased sensit ivity is signa led
by the windshie ld wipers making a s ingle pass over the windshie ld.
Th e rain se nsor wiper inte rvals de pend on the se nsi tivity se tt ing as
well as veh icle speed . During br ief stops, w iper motion will ad just in
re lation to the amoun t of rain on the w indshield.
& WARNING
• Wiper blade s are crucial for safe dr iving! Only wh en they are in
good condition are the y able to clear the windows properly to
provide uncompromi sed vi sibility. Worn or damaged wiper blades
are a safety hazard~
page 78, "Replacing windshield wiper
blade s"! _..
Vehicle care Technical data

Clear vision
& WARNING (conti nued)
• The ra in se nsor i s on ly d esigned to assist and suppo rt the
driv er. It remain s entire ly the dri ver's res ponsibilit y to monitor
out side wea ther cond itions and to m anua lly ac tivate the wipe rs as
s oon as rain or dr izzle reduces visibil ity throu gh the wind sh ie ld.
0 Note
In freezing or nea r freezing condi tions:
• Always check that the wiper blades are not frozen to the glass
before you turn the wipers on. Loosen a w iper blade wh ich is frozen in
place before operating the wipers to prevent damage to the w iper
blade or the wiper motor.
• Do not use the wipers to clear a frosted window. Using the wipers
as a convenient ice scraper will destroy the w iper blades .
• Prior to using a car wash, the windshield wiper system mus t be
switched off (lever in position 0) , This helps to prevent unintentional
switching on and damage to the windshield wiper system .
(I) Tips
• The windshield wipers are switched off when the ignition is turned
off. Activate the winds hield wipers after the ignition is sw itched back
on by moving the windshield wiper lever to any position.
• Worn or d irty windshie ld w iper blades cause smear ing which can
affect the operation of the rain sensor . Check the condition of your
w indshield wiper b lades regularly .
• T he rain sensor is part of the interval wiping system. Turning off
the ignition will also deact ivate the ra in sensor. To reactivate the
sensor, switch off the interval wiping function, then switch it back on
again.
• Make sure the washer fluid reservoir in the engine compartment is
topped off before going on a long trip . Look up=> page
316 for
checking and filling the washer container. •
,,._. ..
Rear window wiper~
The wiper lever is also used to operate the rear window
wiper and the automatic wiper/washer function .
Fig. 69 Wipe r leve r:
ac tiva tin g th e rear
w indow w ip er an d
wa sh er
The rear window wipe r and the automatic wipe r/washe r func­
tions are activate d as follows:
Intermittent wiping
- Push the wiper lever forward to the first position ©
=> fig. 69. The rear window wiper will wipe the window
approx. every four seconds.
Automatic wiper /washer function
- Push the wiper lever forward to the second stop, position
0 , and hold it there for as long as you want the rear
wiper/was her to operate .
- Re lease the lever aga in. the w iper wi ll keep running for
approx . four seconds .
Switching intermittent wiper action off
- Pull the lever all the way back to the original position.

As soon as the reverse gear is engaged and the front w ipers are
turned on and operat ing at the same time, the rear wiper a lso tu rns
on automatically.
& WARNING
Wiper bla des ar e c rucia l for safe driv ing ! Onl y in good c ond ition
are the y able to cl ear the wi ndow s pr operl y to prov ide unr estricted
vi sib ilit y. W orn or fra yed wi per bl ad es are a safety hazard !
=> page 78, "Repla cing wind shi eld wiper blade s"
0 Note
In freezing or near freezing conditions:
• Always check that the w iper blades are not frozen to the glass
befo re you turn the wiper on. Loosen a w iper b lade w hich is frozen in
place before operat ing the w iper to prevent damage to the wiper
blade or the wiper motor.
• Do not use the wiper to clear a frosted window. Using the wipers
as a convenient ice scraper will dest roy the w iper blades. •
Applies to veh icles: with head light washer sys tem
Headlight washer system
The headlight washer system cleans the headlights.
- Operate the windsh ie ld wiper/washer system:::::, page 74,
fig. 68 ® with the headlights turned on by ho lding the
lever for longer than one second .
The washer jets extend forward o ut of the front bumper dr iven by
water pressure to spray the front headlights w ith water .
You shou ld inspect the headlights regularly (for example when refu­
eling) and clean off any solid dirt o r insects from the lenses .
To ensure the system works properly in winter, keep the washer jets
free of snow and remove any ic e using a de-ic ing sp ray .•
Controls and equip ­
ment Safety first
Clear v
ision
Service position
The wiper blades can only be changed in the service posi­
tion.
- I f the wiper blades are not frozen to the windshie ld, bring
the windsh ield wiper l ever to the basic position ®
=:, page 74, fig. 68.
- Select: Function button
I CAR]> System s*> Windshield
wipers > Serv ice positio n.
• On -chang ing the windsh ield wiper blades can only be done if you
bring the wiper arms to the service position. You will also avoid paint
damage to the hood when working on the wipers in this position .
• Off -the w indshield wipers are moved to their initial position
again.
0 Note
Never maneuver yo ur vehicle w ith the front windshie ld wiper arms
ra ised since they will automatically be moved back to their basic posi­
tion above a speed of 3 mph (6 km/h) and can scratch the hood .
[ i ] Tips
• You can also use the service posi tion, for example, if you want to
protect the windshield from icing by using a cover .
• T he serv ice position automa tically switches to
Off when you
operate the windsh ield w iper lever, or speed exceeds 3 mph (6
km/h) .•
Vehicle care Technical data

Clear vision
Replacing windshield wiper blades
Wiper blades in good condition help keep the windshield
clear .
@
Removing a wiper blade
Fig. 7 0 R em ov in g the
wi pe r bla des
Fi g. 7 1 In stallin g
w ipe r b la de s
- Bring the windshield wipers to the service position
~page 77.
- Lift the wiper arm away from the windshield.
- Squeeze t he p lastic bracket on the w indshield wiper arm
together on both sides©~ fig . 70.
- Turn the wiper b lade away from the wiper arm . -
Lift the wi per blade off in the direction of th e arrow @.
Installing wiper blade
- Place the new wiper blade in the retainer on the wiper arm
© ~fig. 71.
Swing t he wiper blade in the direct ion of the arrow @
against the wiper arm.
- Squeeze the co rrugatio n on the w iper until you hear the
bracket click in the wiper ar m.
- Place the w iper arm back again st t he wi ndshi eld .
Clean yo ur wipe r blades regula rly with a w indshield washer solution
to prevent streak ing . If the blades are very dirty , for example with
insec ts, carefully clean t he b lades w ith a sponge o r a soft bru sh .
If the w iper blades begin to streak the wi nds hield, this could be
caused by residue lef t on t he windsh ie ld by au toma tic c ar washes .
Fill the windsh ield washer container w ith a special solut ion avai lable
at your authorized Audi dealer to remove the residue.
& WARNING
Be sure to inspe ct the condition of your wiper blades regularly. See
your author ized Audi dealer for repla cement blade s.
0 Note
• The windshield w iper blades must only be replaced when in the
service position =>
page 77! Otherw ise, you risk damaging the paint
on t he hood or the windsh ield w iper motor.
• T o help prevent damage to the wipe r system, always loosen
blades which are frozen to the winds hield before operat ing wipers . .._

• To help prevent damage to w iper blades, do not use gasoline,
kerosene, pa int thinner, or o ther solven ts on or near the w ipe r
blades.
• T o help prevent damage to the wiper a rms or othe r compo nents,
do not attempt to move the wipers by hand.
W Tips
Commercial hot waxes applied by automat ic car washes affect the
cleanability of the windshield. •
Changing the rear wiper blade
Removing the wiper blade
Fig. 7 2 R ear wind ow
wi per Det achi ng the
r e ar wiper blad e
- Fold the windsh ie ld wi per arm away from the glass .
- Grasp the upp er end of the wiper arm with one hand an d
the meta l clamp on the w iper blade w it h the o ther
=> fig. 72 .
- Hold the wiper arm in t he direction of the arrow@ and
pul l the wiper blade out of th e holder only in the dir ect ion
of th e arr ow @ .
Con tro ls a nd e quip ­
m en t Vehicle
OP-eration
Clear vision
Attaching the wiper blade
- Adjust t he wiper blade in the ho lder.
- Hold the upper end of the wiper arm with one hand .
- Press the wiper b lade into t he holde r with you r other
hand .
- Fold the wi per arm back onto th e windshield.
& WARNING
• To avoid streak s, you should clean the windshield wiper bl ade s
regularl y with window cleane r. Fo r heavy soili ng, for example,
inse ct s, the wiper blades can a lso be cleaned with a sponge or a
cloth .
• For safety reasons , th e wind shield wiper blades shou ld be
replaced on ce o r tw ice a ye ar. •
Mirrors
Manual anti-glare adjustment
Standard setting
- Move the small lever (located on t he bottom edge of the
mir ror) to t he front.
Anti-glare setting
- Move the small lever (located on the bottom edge of the
m irror) to the rear .•
Vehicle care Do-it-yourselt service iTechnical data

____________________________________________ C_l_e _a_ n_ i n--= g=--- a_n_ d----' p,__ r_o _t_ e_ c_ t_ i _o_ n __ _
Windows
Clear vision to all sides.
Clean all windows regularly to remove road film and carwash
wax buildup.
- Remove snow from windows using a brush.
- Use a plastic ice scraper to remove ice from windows and
mirrors.
- Remove other residue on the w indows with a spray-on
glass cleaner .
- Wipe the windows dry with a clean piece of cloth or
kitchen paper towel.
T he best way to remove snow from w indows and mirrors is to use a
brush. Use a non-abrasive plastic ice s craper - be tter st ill, a spray
deicer -to remove ice from windows and mirrors.
Th e w indows must not be cleaned with insect remover or wax since
these can interfere with the function of the w indshield wiper blades
(chatte r) .
Oil, grease, or silicone residue can be removed with glass cleaner or
s ili cone remover. Howeve r, wax residue requires the use of a specially
formulated solvent . Please contact your author ized Aud i dealer for
advice on safe products for wax remova l.
W indows shou ld also be cleaned on the inside at regu lar i nte rvals.
Never dry windows w ith the same chamo is that you use to dry painted
surfaces. Wax res idue on the chamois ca n impa ir v is ion t hrough the
windows .
& WARNING
• Alw ays read and h eed all WARNINGS and other information
~ page 278 .
Safety first
& WARNING (continu ed)
• The windshield must not b e tre ated with w ater-repellent
m aterial s. They c an increa se g lare und er poor visibilit y condit ions
s uch as w etnes s, dar kne ss, or when the sun i s low on the ho rizon .
In addition, they can cau se the wind shi eld wip ers to chatter.
0 Note
• Never use warm o r hot wate r to remove snow and ice from
windows and mirrors . This could cause the glass to crack.
• To prevent damage to the w ires of the rear defogger, do not place
any adhesive stickers on the inside of the rear window over the wires.
• T o help prevent dirt from scratching the w indow, always scrape in
a forward direction - pushing the scraper away from you - never back
and forth .•
Weatherstrips
Complete car care includes the weatherstrips as well .
-Apply a suitable rubber conditioner to the weatherstrips
from time to t ime .
To be able sea l properly, the weatherstrips around the hood, doors,
rear l id, etc. must remain pliable . Spray the weatherstrips with sili­
cone or coat t hem with talc um powder or g lycerine to retain the flex­
ibility of the rubber and to p ro tect them agai nst free zing in the
winter .
& WARNING
Alway s read and heed all WARNINGS and other inform ation
~ page 278 .
Vehicle care Technical data

Alphabetical index 11111 ___________________________________ ____._ _______ _
Ventilatio n
Climate controls ......... ... ..... 111
w
Warning lights . ............ .... ... .. 14
Warning/indicator lights ... ... ... ... .. 10
Adaptive Air Suspension . .. . .... .. .. 18
Adaptive Cru ise Contro l ......... .. . 145
Airbag system ................ .. .. 17
Anti-lock brake system (ABS) ........ 19
Brake system ............ ... ..... . 20
Cru ise control ............ .... ..... 19
E lectronic power cont rol . .... .. ... .. 16
E lectro nic stabil ization p rogram ( ESP) . 16
Glow pl ug sys tem ... .... .. .. .. .. .. 16
H igh beam ......... ...... .. ...... 19
Mal fu nction Indicator Lamp ( MIL) .... 17
Par king brake ..... ....... ... . ... .. 20
Safety belt . ....... .. .. ... .. .. .. .. 18
T ir e pressure monito ring system ... .. 19
Trailer turn signa l assembly ......... 17
Turn s ignals ............ .... .. .... 17
Wa rran ty cover ages . ......... .... .. . 3 68
Washer reservo ir ... ....... ... ... ... . 3 16
Washing . ....... ... .. .. .. .. .. .. .. . 278
Automatic car wash ...... .. .. .... . 279
by hand ...... ...... .. .. .. ... ... . 2 79
General informat ion .... .......... 278
w ith a power washer ........... .. . 280
Waxing .... ..... ... .. .. .... .. .. .. . 281
Wea r indicator . .. .... ..... ..... . .. . 328
Weatherstrips .. ........... ...... .. . 283
Controls and equip­
ment Safety first
We
ights .. .. .. .. .. .... .. .. ... ..... . 363 Defrost ing ... ... .. .. .... ... ... .. 115
What happens i f you wear your safety be lt too Rapid defrosting/defogg ing ........ 116
loose? ..................... ... 206 Win dshield washer flui d
What happe ns to unbelted occupants? . . 203 Low level ... .. .. .. ..... ....... ... 39
W hat impairs driv ing safety? . ....... .. 191
What should I do after changing a wheel? . .
32 5
What should I do after replac ing whee ls? .. .
32 5
Wheel bolts To rque .... .. ........... ...... .. 336
W heels .. .. .. .. ... ................ 318
Cast a lloy .. .. .. .... .. ... .... .... 284
Checking tire pressure ............. 324
Cold tire infla tion pressure ......... 322
General notes ........ .. .. .. .. ... 318
Glossa ry of tire and loading terminology .
319
New tires and whee ls ............. 330
Ti res and vehicle load limits . .. .. ... 326
W hen m ust a safe ty be lt be rep laced? . . 20 4
When m ust the a irbag system be inspected?
222
When should I adjus t th e tire press ures? 325
When should I check t he t ire pressures? . 325
Where a re lower anchorages loca ted? .. . 24 8
Whe re can I find the tire pressures fo r my car?
32 4
W hy safety belts? ........... .. . 201, 202
Windows Clean ing ... .. .. ...... .. .. .... .. . 283
Convenience close/open feature . ..... 60
Defogging ...... ... ... .......... 115 W
inds hield wipers
Changi ng the rear w ipe r blade ....... 79
Fa ulty .. ........... ...... .... .. .. 41
I nte rm it t ent wi ping .. .. ... .. . ... .. 74
One -tap wip ing . ... .. .. ... .. ... ... 74
Rain sensor ... .. .. ... ... ..... .... 74
Rear window wiper ...... ..... ... .. 76
Service position .. .. ............... 77
Washer reservo ir . .. ............. . 316
Winter ope ra tion
Battery ... .. ... .... . ..... .. .. .. . 312
Coolant system ...... .. ... .. .. .. . 308
Heated rear seats .......... ... .. . 122
Steering wheel heating .. .......... 123
Tires . ......................... . 262
Windows ... .. ................ .. 283
Winter ti res .. .. ... .. .. .. .. .. .. .. .. . 33 4
All-whee l drive ....... ... ...... .. . 334
W iper blades
I nsta lling new wiper b lades ....... .. 78
See also Windsh ie ld wipers . . . . . 78 , 79
X
Xeno n-Lig hts . .. ...... ............. . 3 54
y
Yellow symbols . .. .. .. ....... .. .. .. .. 3 7
Vehicle operation Vehicle care Do-it-yourself service Technical data