light AUDI Q7 2012 Owner´s Manual
[x] Cancel search | Manufacturer: AUDI, Model Year: 2012, Model line: Q7, Model: AUDI Q7 2012Pages: 342, PDF Size: 86.42 MB
Page 19 of 342

Instruments and warning/indicator lights 17
o Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (M IL) is part
of the On-Board Diagnostic (OBD II) system.
The symbol
f• lights up when the ignition is
turned on and will turn off after the engine
has started and has sett led at a constant idle
speed. Th is ind icates that the MIL is working
properly.
The warning light illuminates when there is a
malfunction in the engine electronic system .
Contact your author ized Audi dealer and have
the ma lfunction corrected.
An improperly closed fuel filler cap may also
cause the MIL light to illuminate (only vehiÂ
cles with gasoline engine)
c:> page 253.
For more informat ion c:> page 2 7.
0 Adaptive Air Suspension
Applies to vehicles: with Adaptive Air Suspension
This II warning/indicator light has the folÂ
l owing functions:
- It illuminates for a few seconds after the igÂ
nition is turned on as function check and
then goes out .
- If the warning/ind icator light illuminates or
blinks continuously, there is a system fau lt
in the Adaptive A ir Suspension . A system
fault can result in limited ride comfort and
low ground clearance . Drive safely to the
nearest authorized Aud i dealer or qualified
workshop, and have the fault corrected .
- If the warning/ind icator light flashes, you
should not drive the vehicle. The flash ing
warning/ind icator light po ints to an extreme
High level. A very
pronounced lifting of the
vehicle (extreme High level) can resu lt, fo r
example, when a heavy load is removed
from the vehicle. As soon as the leve l has reÂ
turned to normal, the warning/indicator
light stops flashing, and you can drive away.
- If the warning/ind icator light flashes in conÂ
junction with the
II warning/indicator
light, you sho uld not drive off immediately
i n order to prevent damage to the underÂ
body. The two warning/ind icator lights flashing together points to an extreme Low
level. A very
pronounced lowering of the veÂ
hicle (extreme Low leve l) can result, for exÂ
ample, from a heavy load. As soon as the
level has retu rned to normal, the warning/
ind icator lights stop flashing, and you can
drive away.
(D Note
If the warning/indicator light flashes in
conjunction with the
II warni ng/indicaÂ
tor light, you should not dr ive the veh icle
because low-lying vehicle parts can botÂ
tom out as you drive over uneven ground
and be damaged as a result.
~ Adaptive Air Suspension
Applies to vehicles: with Adaptive Air Suspension
This II warning/ indicator light has the fol Â
lowing functions:
- It illuminates for a few seconds after the igÂ
nition is turned on as function check and
then goes out.
- It comes on for approximately 15 seconds
as a warning of
reduced ground clearance , if
the dynamic mode is activated and if the igÂ
nition is switched on
r:!;> page 150, Chassis
controls.
- If the warning/indicator light flashes in conÂ
junction with the
II warning/indicator
light, you should not drive the vehicle immeÂ
diately in order to prevent damage to the
underbody. The two warn ing/ indicator
lights flashing together points to an exÂ
treme Low level. A very
pronounced lowerÂ
ing
of the vehicle (extreme Low level) can reÂ
sult, for example, from a heavy load. As
soon as the level has returned to normal,
the warning/indicator lights stop flashing,
and you can drive away.
(D Note
If the warning/indicator light flashes in
conjunction with the
II warning/indicaÂ
tor light, you should not drive the vehicle
Page 20 of 342

18 Instrum ent s and w arn ing /indic ato r light s
because low -lying vehicle parts can bot Â
tom out as you drive over uneven ground
and be damaged as a res ult .
~ Safety belts
This warning/indicator light reminds you to
put on your safety b elt.
The . warn ing/ indicato r light illum inates
when the ignition is switched on to remind
the d river and (on USA models only) any front
passenger to put on the safety belt . Add itionÂ
ally, an acous tic warning (gong) will also
sound.
F or more Information
r=) page 170, Safety
belt warning light.
~D High beam
The ii warning/indicato r light illuminates
when the high beams are on or when you use
the head light flasher . For more informat ion
about using the h igh beams, seer=)
page 60.
(l) Tire pressure monitoring system -
telltale ind icator lamp
The warning/indicator light appears in the
event of a significant loss of tire pressure or if there is a malfunction .
The indicator light (I] ill um inates to check the
function w hen you switch on the ign ition.
If the
(I] symbol remains on or b links after
you switch on the ignition, there is a loss of
tire pressure or a system malfunction . If there
is a system malfunction , see your au thorized
Aud i dealer as soon as possib le.
Detailed info rmation on the tire pressure
monitoring system can be found in
r=) page292.
CRUISE /'(-) Cruise control
The lff;jl)~i~ (USA mode ls) ;II (Canada mode ls)
warning/indicato r light illuminates when the
cr uise contro l is activated .
ABS/(8) Anti -lock brake system (ABS)
T his warning/indicator light monitors the ABS
and the electronic differential lock (EDL) .
Them (USA models) ;ii] (Canada models)
warning/indica tor ligh t will come on for a few
seconds when the ignition is switched on . T he
l ight will go out after an automat ic check seÂ
quence is comp leted.
There is a malfunction in the ABS when:
-The warning/indicator light does not illum iÂ
nate when you switch on the ignition .
- The warning/indicator light does not go out
after a few seconds.
- T he wa rning/indicator light i llum inates
while driving.
The brake system will still respond e ven
without the ass istance of the ABS system.
See your authorized Audi deale r as soon as
possible to restore full braking perfo rmance.
For more information regard ing the ABS
<=> page 223.
The AB S warning light and the brake wa rnÂ
ing light come on together. The ABS will not
work and you will notice a change in braking
r es ponse and p erform ance.
Malfunction in the brake system
If the brake warning light r=) page 19 and
the ABS warning ill uminate
together there
may be a malfunction in the ABS, and there
may also be a malfunction in the brake system
i tself <=>
A.
In the event of a malfunction in the brake
system
the warning/indicator ligh t 1111
(USA models)/ . (Canada mode ls) in the inÂ
st rument cluster flashes . By press ing the
jCH ECKI button, you can b ring up a d river
message whi ch explains the malfunction in
more de tail. Please note
<=> page 32 .
Malfunction in the electronic differential
lock (EDL)
The EDL works toge ther w it h the ABS. The
ABS wa rning lig ht w ill come on if there is a
malfu nction in the EDL sys tem
<=> page 221 .
Page 21 of 342
![AUDI Q7 2012 Owner´s Manual Instrument s and warnin g/indic ator ligh ts 19
See your authorized Audi dealer as soon as
poss ibl e.
A WARNING
- I f the m (USA mode ls)/ 11] (Canada
mode ls) warning light does not AUDI Q7 2012 Owner´s Manual Instrument s and warnin g/indic ator ligh ts 19
See your authorized Audi dealer as soon as
poss ibl e.
A WARNING
- I f the m (USA mode ls)/ 11] (Canada
mode ls) warning light does not](/img/6/40277/w960_40277-20.png)
Instrument s and warnin g/indic ator ligh ts 19
See your authorized Audi dealer as soon as
poss ibl e.
A WARNING
- I f the m (USA mode ls)/ 11] (Canada
mode ls) warning light does not go out,
or if it comes on while driving , the ABS
system is not working properly . The vehi Â
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides .
Contact your authorized Aud i dea ler as
soon as possible .
-USA models: If the - warning light
and
the m warning l ight come on toÂ
ge ther, the rear wheels could lock up
first under hard braking . Rear wheel lockÂ
up can cause loss of vehicle control and
an accident. Have your vehicle repaired
immediately by your authorized Audi
dealer or a qualified workshop. Dr ive
slowly and avoid sudden, hard brake apÂ
plicat ions .
-Canada models: If the brake warn ing
light . and the ABS wa rning light
II]
come on together, the rear wheels could
lock up first under ha rd b rak ing . Rea r
wheel loc k-u p can cause loss of veh icle
control and an accident . Have your vehiÂ
cle repaired immediately by your a uthorÂ
ized Audi dea ler or a qualified workshop .
Drive slowly and avo id sudden, hard
brake applicat ions .
::J.:.I(®) Parking brake
The indicator light monitors the parking
brake.
-
When the pa rking brake is applied and the igÂ
n ition is switched on, the. (USA mode ls)
I
• (Canada models) indicator lig ht comes o n.
T he indicator light must go out when the
parking b rake i s re leased.
BRAKE/((])) Brake system
T he warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction .
The - (USA models)/ . (Can ada models)
l ight illum inate s when the ignition is turned
o n. It goes out after the eng ine has been
started . This ind icates that the bra ke warning
li gh t is func tioning properly.
If th e brak e warning light do es not light up
w hen the engin e is cran king, ther e may be a
malfunction in the electrical s yste m . In this
case, c onta ct your Audi dealer .
If the brake system warn ing/indicator light
flashes , there is a brake system malfunction .
By pressing the
! CH ECK I button , you can bring
up a d river message which expla ins the ma lÂ
f unct ion in mo re det ail
~page 32.
If the ABS fails, the ABS warn ing/indicator
li ght
m (USA models)/ ll] (Canada models)
flashes togethe r wi th the brake system warn Â
ing/ indica tor light ¢
A.
(USA mode ls): If the warn ing light - and
the war ning light
El illuminate toget her, imÂ
med iate ly contact yo ur autho rized Aud i dea le r
o r q ualified wor kshop to have all brake pads
inspec ted
~ page 36 .
When the light comes on , an aud ible warning
s ignal is also g iven .
A WARNING
-USA models: If the - warning light
and them warning light come on to Â
gether, the rear wheels could lock up
f ir st under hard bra king . Rear wheel lockÂ
up can ca use loss of vehicle control and
an accident . Have yo ur vehicle repaired
immed iate ly by your authorized Aud i
deale r or a qua lified workshop . Drive
slowly and avo id sudden, hard brake apÂ
plications.
- Canada models: If the brake warning
light . and the ABS warn ing light
II]
come on togethe r, the rear whee ls could
.
Page 22 of 342

20 Instrum ent s a nd w arn in g/i ndic ato r light s
lock up first under hard braking. Rear
wheel lock-up can cause loss of vehicle
control and an accident. Have your vehiÂ
cle repaired immediately by your authorÂ
ized Audi dealer or a qualif ied workshop.
Drive slowly and avo id sudden, hard
brake applicat ions.
- If the brake warning/indicator light does
not go out after a few seconds and the
par king brake re leased, or lights up while
yo u are driving, the fluid level in the
brake fluid reservo ir is too low . If you be Â
lieve that it is safe to do so, proceed imÂ
mediately at low speed to the nearest
authorized Audi dealer or qualified repair
facility and have the brake system inÂ
spected.
- Always keep in m ind that after several
brake applicat ions, you will need greater
pressure on the brake peda l to stop your
vehicle . Do not rely on stra ined brakes to
respond w ith maximum stopp ing power
in critical situations. You must a llow for
increased bra king distances . The extra
distance used up by fading brakes could
lead to an accident .
Page 23 of 342

Driver information
display
Introduction
General notes
The driver informa tion display inside the inÂ
strument cluster provides you, the driver,
with much useful information.
Fig. 9 Instr ument cluster: ce nter display
Information from the Driver Information SysÂ
tem is shown in the display in the center of
the instrument cluster.
When you turn on the ignition and while you
are driving, some functions and vehicle comÂ
ponents are scanned for their operating staÂ
tus. Malfunctions or required service proceÂ
dures are signalled aud ibly and shown by red
and yellow lighted symbols and rem inders to
the dr iver in the display.
The driver is also shown information about raÂ
d io and CD operation and directions for the
nav igation system . You can f ind additional inÂ
formation on these subjects in the MMI manÂ
ua l.
The Driver Information System prov ides the
following functions:
Sound system disp lay ¢
page 21
Outside air temperature ¢page22
Digital speedometer ¢page
22
Door open indicator ¢page22
Defective light b ulb ¢poge23
Service interval display ¢page23
Auto Check system ¢
page 30
Driver information ¢page30
Dri
ver inform ation di spl ay 21
Speed warn ing system
Cruise control
Adaptive cruise control *
Selector lever pos ition
Adaptive Air Suspension *
T ire pressure monitori ng
(D Tips
¢page28
--·--¢page24
¢page 111
--..--
¢page 113
¢page 138
¢page292
In the event of a malfunction either a red
or ye llow icon appears in the display . Red
symbols indicate
Dang er ¢ page 31. YelÂ
l ow symbo ls indicate a
Warning
¢ page 34.
Sound system display
Fig. 10 Display: sound syste m
If priority 1 or pr iority 2 faults are not shown
by the Auto Check Control, the name of the raÂ
dio station you are tuned to or t he frequency
and the recept ion range are shown in the upÂ
per area of the d isplay.
When the CD is in use, the tit le of the track
being played is shown. The number of the CD
(CDI to CD6) cur rently be ing played is also
s h own.
Page 24 of 342

22 Driver in formation d ispl ay
Outside temperature display
Fig. 11 Display : outside temperature
At temperatures below 41 °F (+S °C) a snowÂ
flake symbol appears ahead of the temperaÂ
ture display . It is intended to remind the drivÂ
er to pay spec ial attent ion to
ic e on the roa d.
If the vehicle is stationary, or if you are driving
at a very low speed, the temperature shown in
the display might be slightly higher than the
actual outside temperature . Th is is caused by
the heat being rad iated from the engine .
If you have selected the °C (degrees Celsius)
unit for temperature in the MMI, the outside
temperature display also appears automat iÂ
cally in
°C.
A WARNING
- Never rely excl usively on the outside
temperatu re d isplay to determine if a
road surface is icy or not . Keep in mind
that road surfaces, especially bridges
and overpasses, could be ice covered and
s li ppery even at an outs ide temperature
above 41 °F (+ S °C).
- Always remember, even if the "snowÂ
flake" symbol (ice warn ing) does not apÂ
pear in the display, black ice could be on
the road.
- Always reduce your speed and dr ive with
special care in cold weather conditions
when the chance of encountering icy road s urfaces increases .
Digital speedometer
Fig. 12 Display: Digi tal speedometer
Current speed appears in the disp lay. Speed is
shown in 1 mph measures (USA models) or 1
km/h measures (Canada models) .
You can switch the disp lay from m iles to kiloÂ
meters and vice versa via the MMI.
Open door or trunk lid warning
The pictogram alerts you when doors or the
rear lid have been left open .
Fig. 13 Display: open doo r or rea r lid wa rning
With the ign it ion sw itched on, the ope n door
or rear lid warning illuminates when at least
one door or the hood or the trunk lid is not
cl osed . The symbol a lso shows you
which
doo r(s) o r lid is not closed.
In the illustration
~ fig . 13 it is the dr iver's
doo r, the left rear door and the rear lid. As
soon as all the doors, the hood, the rear lid
and the f uel filler cap are prope rly closed, the
door and rear lid warning turns off and the
Driver Information System functions selected
are displayed again.
Page 25 of 342

Defective light bulb warning
The defective light bulb warning tells you
when a vehicle light bulb has become defecÂ
tive.
Fig . 14 D isplay : defective lig ht bu lb warn ing
The defective light bu lb warning monitors the
function of the light bulbs . If th is symbol
ii
illuminates, a brake light, a turn signal (front
or rear), a headlight, the backup light, a fog
light or a rear fog light has failed.
A WARNING
- light bu lbs are pressurized and could exÂ
plode while they are being changed causÂ
ing serious personal injury.
- Work w ith due care when handling the
high-voltage section of gas discharge
(xenon) lights. Fa ilure to do so could reÂ
sult in dea th o r se rious injury.
(D Tips
Have the bulb replaced or the connection
repa ired by you r autho rized Aud i Service
department.
Dri ver inform ation di spl ay 23
Service interval display
The service interval display reminds you when
your next service is due .
Fig . 1 5 Display: Serv ice interva l d isplay
T he schedule for the nex t oi l change or inspecÂ
tion is ca lculated automatica lly and disp layed
accordingly. The disp lay works in two stages:
Service reminder
30 days before t he nex t se rvice is due, a servÂ
i ce reminde r appea rs in the display whe n you
turn on the ignition
~fig. 15.
After about 5 seconds the display switches
back to norma l. The distance and time reÂ
mai ning are updated each time the ignit ion is
turned on unt il t he da te d ue for se rv ice is
reached.
Service due
When the due date fo r se rvice is reached, the
mes sage
Se rv ice due! appears in the instr uÂ
ment cluster immed iate ly after yo u tur n on
the ignit ion. Addit iona lly, a warning tone
sounds. After about
5 seconds the disp lay
switches back to normal.
Calling up the service schedules
If or when an oil change o r inspection is due,
can be shown in the MMI display by selecting
the service in terval d isplay in the car menu .
Se lect funct io n button
ICARI > contro l button
S ys tem s* > Service inter val display or I CAR I>
control button Car sy stems * > Servicing &
checks > Service inte rvals .
Page 29 of 342

Other equipment
Applies to vehicles: with efficiency program
Fig. 20 D isplay : ot her equipment
• In the efficiency program, press the funcÂ
tion selection switch¢
page 25, fig. 18@
repeatedly until the other equipment apÂ
pears in the display .
Other equipment that is currently affecting
fuel consumption is lis ted in the efficiency
program . The display shows up to three other
items of equipment @. The equipment using
the most fuel is l isted first. If more than three
items using fue l are switched on, the equ ipÂ
ment that is currently using the mos t fu el is
d isp layed .
A scale @also shows the current total conÂ
sumpt io n of all other equ ipment .
Fuel economy messages
Applies to vehicles: with efficiency program
Fig. 2 1 Display: fuel eco nomy messa ge
-.:,
~
Fuel economy messages are disp layed when
fuel consumption is inc reased by certain conÂ
d itions . If you follow these fuel economy mesÂ
sages, you can reduce your vehicle's consumpÂ
tion of fuel. The messages appear automati Â
cally and are o nly displayed in the eff ic iency
Dri ver inform ation di spl ay 2 7
program . The fue l economy messages t urn off
automatica lly after a certain period of time.
• To tu rn a fuel economy message off immeÂ
diately after it appears, press the
I RESE T!
button ¢ page 25 , fig. 18@, or
• Press the f unction selection switch
r::!) page 2 5, fig . 18 @ .
{I) Tips
-Once yo u have turned a fuel economy
message off, it will o nly appear again afÂ
ter yo u turn the ign ition on again.
- Th e fuel economy messages are not disÂ
played in every instance, but rather in in Â
tervals
over a period of time.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
The Malfunction Indicator Lamp (MIL) ¢• in
the instrument cluster¢
page 14, fig. 8 is
part of the On-Board Diagnos tic (OBD II) sysÂ
tem .
The warning/indicator light ill um inates when
the ignition is switched on and goes out after
the engine star ts and the id le has stabilized.
This indicates that the M IL is working prope rÂ
ly .
If the light does not go out after the engine
is started , or illuminates while you are dr ivÂ
ing, a malfunction may exist in the engine sys Â
tem . If the light illuminates, the catalytic conÂ
verter could b e damaged .
Con tinue driving
with reduced powe r (avoidÂ
ing s ustained high speeds and/or rapid accel Â
erations) and have the cond ition co rrected .
Contact your a uthorized Aud i dea ler.
If the light illum inates, the electronic speed
limiter may also be malfunctioning . For more
information ¢
page 28, Electronic speed
limiter.
An improperl y closed fuel filler cap may also
cau se the MIL light to illum inat e (onl y vehiÂ
cle s with g asoline engine )
¢ page 253.
Page 30 of 342

28 Driver information d isplay
On-Board Diagnostics
Fig. 22 Locat ion of Data Link Connector (DLC)
On-Board Diagnostics monitors the compoÂ
nents of your emission control system. Each
monitored component in your engine system
has been assigned a code . In case of a malÂ
function, the component will be ident ified
and the fault stored as a code in the control
module memory .
The MIL light may also illuminate if there is a
leak in the on-board fue l vapor recovery sysÂ
tem.
If the light illuminates after a refuelling ,
stop the veh icle and make sure the fuel filler
cap is proper ly closed (on ly vehicles with gasoÂ
line engine)
¢page 253.
In o rder to make an accurate d iagnosis, the
stored data can only be displayed using speÂ
cial diagnostic equipment (generic scan tool
for OBD).
I n o rder to connect the special diagnostic
equipment, push the plug into the Data Link
Connector (DLC) . The DLC is located to the
right of the hood release¢
fig . 22.
Your author ized Audi dealer or qualified workÂ
shop can interpret the code and perform the
necessary repair.
A WARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
ma lfunctions, which can increase the risk
of a collis ion!
Electronic speed
limiter
Your vehicle may be factory equipped w ith
t ir es that are rated for a maximum speed of
130 mph (210 km/h) . This is less than the
maximum speed of your vehicle . To reduce the
risk of sudden tire fa ilure a nd loss of contro l if
the vehicle is operated at excessive speeds,
your vehicle also has an elec tronic speed limitÂ
er . The e lectronic speed limiter prevents your
vehicle from going faster than the tire speed
rating . For more information ¢
page 285.
If the engine control unit receives faulty vehiÂ
cle roadspeed signals, the Malfunction Indica Â
tor Lamp (MIL)
II will ill uminate. If this ocÂ
curs, contact the nearest authorized Audi
dealer for assistance.
A WARNING
-
Always observe the posted speed limits
and adjust your speed to suit prevailing
road, traffic and weather cond itions . Never
drive your vehicle faster than the maxiÂ
mum speed rating of the tires installed.
-
Speed warning system
Overview
The speed warning system helps you to keep
your driving speed below a set speed limit.
T he speed warning system warns the driver if
he exceeds a previo usly stored maximum
speed . A warning tone wi ll so und as soon as
the vehicle speed exceeds the set speed by about 3 mph (3 km/h). At the same time, a
warning symbol appears in the display.
The speed warning system has
two warning
thresholds
that function independently of
each other and that have somewhat different
purposes:
Speed warning 1
You can use speed warning 1 to set the maxiÂ
mum speed while you are driving. This setting "'
Page 33 of 342

For example, the symbol Ill appears in the
display, indicating low windshield washer fluÂ
id level. The follow ing message also appears:
Pl eas e refill w asher flu id
The driver message disappears after a few
seconds. The driver message can be displayed
again by briefly pressi ng the
!CHECK I button.
Red symbols
A red symbol means DANGER.
Fig. 25 Display: engine coolant level warning (pr ior ity
1)
• Pull off the road .
• Stop the veh icle.
• Turn off the engine .
• Check the ma lfunctioning system. Contact
your authorized Aud i dea ler or a qualified
workshop for assistance.
Red symbols indicate a priority 1 ma lf u nction
- Danger!
W ith a pr iority 1 malfunction, a large symbol
appears in the center area of the display
¢ fig. 25. When the symbol appears, three
warning tones sound in succession . T he symÂ
bol co nti nues to bli nk until the ma lf u nct ion
has been repaired.
I f there are
more than one prio rity 1 ma lfuncÂ
tions, the symbols appear one after the other
for about 2 seconds.
An addit ional driver message can also be d isÂ
p layed by briefly pressing the
I CHECK ! button.
The red symbols mean:
Driver inform ation di spl ay 31
@ Tips
Alternato r malfunction
<:!> page 31
USA models: Brake system
malfunction
r:!>page32
Can ad a mod els : B rake sysÂ
tem malfunc tion
r:!> page32
Engine coolant level too
low/engine coolant temperÂ
ature too high
<:!>page 32
Engine oil pressure too low
<:!>page 33
Refill Ad Blue*
¢page255
AdBlue malfunction*
<=> page255
Faulty steering
r:!>page33
Fa ulty ignition switch
<=>page34
-If the wa rning/ind icator light 11111 (USA
mode ls)/ . (Canada mode ls) in the inÂ
strument cluste r flashes, there is a brake
system malfunction. By pressing the
! CHECK I but ton, you can bring up a driver
message which explains the malfunction
in more detail. Please note
r:!> page 32.
-Speed warnings threshold 1. (USA
mode ls)/ . (Canada models) and thresh Â
old 2. (USA
models) ta (Canada modÂ
els) are also shown as red symbols. The
warning is always shown as a small symÂ
bol in the upper area of the display
r:!> page 28 .
0 Alternator malfunction
If the . symbo l in the instrument pane l disÂ
play flashes, then there is a malfu nction in the
alternator or the vehicle elect ron ics. A warn -
ing to the driver will appear, too. The driver ..,_