brake light AUDI RS5 COUPE 2015 Owner's Guide

"' N
0:: I-­co
rl I.O
"' N
"' rl
Check in g and Fillin g
Engine compartment
Engine compartment
These are the most important items that you can check.
Fig. 161 Typical layout for containers and eng ine oil filler cap
(D Coolant expansion tank (.J-) .. .. .
@ Jump start point(+) under a cover
@ Engine oil filler cap(~) .... .. .
@ Jump start point(-) with hex head
screw . ............... ...... .
® Brake fluid reservoir ((0) .. .. .. .
@ Windshield/headlight* washer con-
tainer
(Q) .................. .
&, WARNING
193
198,229
191
198,229 195
200
Before you check anything in the engine com­
pa rtment, always read and heed all WARN­
INGS
~ .&. in Working in the engine compart­
ment on page 187 .
Engine oil
Engine oil specifications
The engine oil used must conform to exact speci­
fications.
T he service interval disp lay in the instr ument
cluster of your vehicle will inform you when it is
time for an oi l change. We recommend that you
have your oil changed by an authorized A udi Serv ­
ice Advisor .
If you have to top off the o il between o il changes,
use the Audi oil qua lity standard specified in the
table .
Audi oil quality standard
G as oline
VW S02 00 or
eng ine vw 504 00
1 8 9

"' N
0:: l­oo
rl I.O
"' N
"' rl
forced out through the pressure relief valve
in the cap when the engine becomes hot.
- If, in an emergency, only water can be add­
ed, the correct ratio between water and an­
tifreeze
q page 192 must be restored as
soon as possib le.
@ For the sake of the environment
Drained coolant should not be reused . Always
dispose of used coolant while observ ing a ll
environmental regulations.
Radiator fan
The radiator fan switches on automatically by it­
self.
The radiator fan is driven by the engine via the V­
be lt. The viscous clutch regulates the speed of
the fan according to the temperature of the cool­
ant.
An auxiliary e lectr ic radiator fan * switches on and
off depending on coo lant temperature and other
veh icle operating conditions.
Afte r you switch the engine off, the a uxiliary fan
can cont inue running for up to 10 minutes -even
with the ignition off. It can even switch on again
l ater by itself
Q .&. , if
- the temperature of the engine coolant rises due
to the heat bui ld-up from the eng ine in the en­
gine compartment, or
- the engine compartment heats up because the
vehicle is parked in intense sunlight.
_& WARNING
- To reduce the r isk of personal injury never
touch the radiator fan.
- The aux iliary e lectr ic fan is temperature con­
trolled and can switch on suddenly even
when the engine is not running.
- The auxiliary radiator fan switches on auto­
matically when the engine coo lant reaches a
certain temperature and will continue to run
until the coolant temperature drops.
Ch eck in g and Fillin g
Brake fluid
Checking brake fluid level
The broke fluid level con be checked with a quick
glance.
F ig . 1 66 Engine compartment: Cover on the brake fluid
r eservoir
Before you check anyth ing in the engine compart­
ment,
a lw ays r ead and h eed all WARNING S
q ,& in Working in the engine compartment on
page 187.
., Read the brake fluid level from the brake fluid
reservoir
q fig. 166, r:> page 189, fig. 161. The
brake fluid level must be between the "MIN"
and "MAX" markings.
The brake fluid reservo ir is located at the rear
part ition of the engine compartment on the left
s ide
q page 189.
The fluid level may drop slightly after some time
due to the automatic adjustment of the brake
pads. This is not cause for alarm.
If the brake fluid level falls
considerably below
the "MIN" mark, the brake warning/indicator
light (U.S. models:
1111 , Canad ian models: .
will come on
Q page 15 . Do not continue to oper­
ate the vehicl e. The complete brake system
shou ld be thoroughly chec ked by an autho rized
A udi dealer or qualified workshop and the cause
corrected. If the brake fluid level is too low, the
brake warning/indicator light will illuminate .
Contact an a uthorized Audi dea ler
immedi ately .
(0 Tips
The brake fl uid reservoir is located under­
neath the cover.
195

Checking and F ill in g
Changing brake fluid
Have the brake fluid changed by an experienced
technician .
Brake fluid absorbs moisture from the a ir. If the
water content in the brake fluid is too high, cor­
rosion in the brake system may result after a peri­
od of time. The boiling point of the brake fluid
will also dec rease conside rably and dec rease
b ra ki ng perfo rman ce.
Therefore, the brake flu id must be changed
e ve ry
two y ear s.
Always use new b rake fluid wh ic h con­
forms to Fede ral Motor Vehicle Standard " FMVSS
1 16 DOT 4".
The brake fluid reservoir can be difficult to reach,
therefo re , we recommend that yo u have the
b rake fluid changed by your authori zed
Audi
dealer . Your dealer has the cor re ct too ls , the
righ t brake fluid an d the know-how to do t his for
you.
A WARNING
- Brake fluid is po isonous. It must be stored
only in the closed orig inal container out of
the reach of children!
- Brake fai lure can result from old o r inappro­
pr iate bra ke fluid . Observe these p recau­
t ions:
- Use on ly bra ke fluid t hat meets SA E speci­
fication
J 17 03 and confo rms to Fede ral
M otor Vehicle S tand ard 116 . Always check
wit h your author ized Audi dea ler to make
sure yo u are using the correct brake f lui d.
The cor rect type of b rake fluid is a lso indi­
cated on the bra ke fluid reservo ir.
- The brake fluid m ust be new. Heavy use of
the bra kes can cause a va por l ock if the
brake fluid is left in the system too long.
This ca n ser iously affect the effic iency of
the brakes as we ll as your safety . This
co uld res ult in an accident.
@ Note
Brake f lu id will damage the paint of y our vehi­
cle.
196
® For the sake of the environment
Because of t he prob lem of prope r disposal of
brake fluid as well as the special tools re­
q uired and the necessary expert ise, we rec­
ommend that yo u have the brake f lu id
changed by your autho rized Aud i dea le r.
Battery
General information
Under normal operating conditions, the battery
i n your A ud i does not need any maintenance .
With
high outside temperatures or long dai ly
drives we recommend that you have the e lectro­
l yte level checked by an aut horized Aud i dea ler or
qualified workshop . The e lectrolyte leve l should
also be chec ked each time the batte ry is cha rged
¢ page 198.
Have the battery checked when you take your ve­
hicle i n for service . You are well adv ised to re ­
place a battery that is older than 5 years .
With certain types of airbag deployment, the bat­
tery is disco nnected from the ve hicle elect rical
system for safety reasons
¢ A in Repair , care
and disposal of the airbags on page 141 .
Disconnecting the battery terminals
Some vehicle functions (power window reg ula­
tors, for example) are lost if the battery te rm i­
nals are d isconnected . These funct ions have to be
r elearned after the battery t ermina ls are con­
nected again . To prevent t his, the battery sho uld
o nl y be disconnected from the ve hicle e lectr ica l
system when absolute ly necessary fo r rep airs.
Vehicles not driven for long periods
If you do not drive your vehicle ove r a period of
several days or weeks, electrical components are gradua lly cut back or sw itched off . T his reduces
energy cons umption and mainta ins start ing ca­
pabili ty ove r a longer period¢
page 175.
Some of the convenience funct ions may not ope r­
ate, such as the inter ior lights or the power s eat
adjus tment . The conve nien ce f unct io ns w ill be
ava ila ble again when you tu rn on the ig nition an d
star t the eng ine. ..,..

Emerg enc y ass is tance
"' Remove the valve cap from the tire valve and
unscrew the valve insert using the accompany­
ing valve insert tool¢
fig. 176.
"'Lay the valve insert on a clean surface.
"' Remove the sealing plug from the filling hose
and connect the hose to the tire valve .
"' Hold the bottle w ith the bottom facing upward
and empty the ent ire contents into the tire .
"'T hen pull out the hose and screw the valve in­
sert t ight ly back into the tire va lve.
Inflating a ti re
"' Screw the filling hose for the electric air pump
onto the tire valve and insert the connector into
the cigarette lighter .
"' Inflate the tire between 2.0 and 2.5 ba r and
read the pressure from the ga uge .
"' If this tire pressu re is not reached, drive your
vehicle approximate ly 10 meters forward or
backward so that the sea lant can be redistribut­
ed inside the tire. If at this time the required air
pressure st ill cannot be reached, the tire is too
badly damaged and cannot be repa ired with the
ti re sealant.
F in al ch eck
"' After driving for about 10 minutes, stop and
check the tire press ure.
"' If tire pressure is less than 1.3 bar, the tire is
too severely damaged . Do not cont inue to
drive. Seek professional assistance .
A WARNING
- Turn on the eme rgency flashers and set up
the emergen cy tr iangle if you have flat tire
wh ile in moving traffic. Th is is for yo ur pro­
tection and the for the safety o f other driv­
ers.
- Have all passengers leave the vehi cle and
stay away from the danger zone (for exam ­
ple, behind a guard rail).
- Read and fo llow the manufacturer's safety
precautions on the compressor and in the
instructions on the bottle of sealant!
- If a t ire pressure of 2.0 bar cannot reached
after inflating for six minutes, then the tire is too severe ly damaged . Do not contin ue
dr iv ing !
218
-Obtain qua lified help i f it is not possible to
perform the repair w ith the t ire sea lant.
- If the tire pressure is less than 1 .3 bar after
10 minutes of driving, then the the t ire is
too severe ly damaged. Do not continue driv­
ing. Seek professional assistance.
(D Note
Partic ular care is necessary if you are mak ing
a tire repa ir on a steep incl ine.
(D Tips
- Do not operate the electric air pump for
more than 6 minutes witho ut stopp ing, oth­
erwise it can overheat. When the air pump
has cooled down, you can continue to use it.
- If sea lant has spilled out, let it dry and then
you can remove it by peeling it away like a
foil.
- Remember to obtain a new bott le of sealant
from your authorized Audi dealer after re­ pairing a tire. After this, the functionality of
the tire repair set is restored .
- Obey all laws.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
"' After you experience a t ire failure, pull the ca r
well away from mov ing traffic and t ry to reac h
l e vel ground before you stop
~ ,&.
"' All passengers should leave the car and move
to a safe location ( for ins tance , behind the
guardrail) ¢,& .
"' Engage the parking brake to prevent your ve hi­
cle from ro lling unintent iona lly ¢ ,& .
"' Move the selector le ver to the P position .
"' Take the jack
¢page 216 out of the luggage
compartment .

M N
0:: l­oo ,...., \!) 1.1'1
N 1.1'1 ,....,
A WARNING 1=
You or your passengers cou ld be injured while
chang ing a wheel if you do not follow these
safety precautions:
- If you have a flat t ire, move a safe distance
off the road . Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- To help prevent the veh icle from mov ing
sudden ly and possibly slipping off the jac k,
always fully set the pa rking brake and block
the whee l diagona lly opposite the w heel be­
ing changed with the folding chocks or oth ­
er objects. When one front wheel is lifted
off the ground, placing the Automatic Trans­
mission in "P" (Park) will
not prevent the ve ­
hicle from moving.
- Before you change a wheel, be sure the
ground is level and firm. If necessary, use a
sturdy board under the jack.
- Always store the vehicle tool kit, the jack *
and the replaced tire in the luggage com­
partment
c> page 117.
(D Note
If you are changing the wheel on a steep in­
cline, use a rock or sim ilar object to block the
opposite whee l to prevent the vehicle from
mov ing.
{!) Tips
Obey a ll laws.
Changing a wheel
When you change o wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the wheel bolt caps*. F or more de­
tails see also ¢
page 220 , Wheels with
wheel bolt caps .
2. Loosen the wheel bolts¢ page 220.
Emerge ncy ass is tanc e
3. Locate the proper mounting point for the
jack and alig n the jack below that point
¢ page 221 .
4. Lift the car with the jack¢ page 221.
5. Remove the wheel with th e fla t tire and then
install the other wheel¢
page 222 .
6. Tighten all whee l bolts lightly.
7 .
Lower the vehicle with the jack .
8. Use the wheel bolt wrench and
firmly t ighten
all wheel bo lts in a crisscross pattern
¢page 220.
9. Replace the wheel bolt cap s* .
A WARNING
A lways read and fo llow all WARNINGS and in­
formation
¢ &. in Raising the vehicle on
page221
and ¢page 223.
After changing a wheel
A wheel chonge is not complete without the do­
ing the following.
.. Always store the vehicle tool kit, the jack*, and
the replaced tire in the luggage compartment
¢ page 117.
.. As soon as possib le, have the t ightening tor­
ques
on all wheel bolts checked with a torque
wrench . The correct t ightening to rque is 90 ft
lbs. (120 Nm) .
.. Have the flat tire
replaced as soon as possible .
(D Tips
-If you not ice that the wheel bo lts a re cor­
roded and difficult to tur n while changing a
tire, they should be replaced before you
check the tigh tening torque.
- Dr ive at reduced speed until you have the
tightening to rques che cked.
219

"' N
0:: l­oo
rl I.O
"' N
"' rl
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed .
-
Fig. 179 Sill panels: marking s
Fig. 180 Sill: posit ion ing the vehicl e jack
The location of the jack point is indicated by an
indentation on the underside of the vehicle
¢ fig. 179.
.,.. Activate the pa rkin g brake to prevent the vehi­
cle from rolling unintentionally .
.,.. Move the se lector lever to position P .
.,.. Find the
m ar king (raised area) on the sill that is
nearest the wheel that wi ll be changed
<=> fig . 179. Behind the marking, there is a lift­
ing point on the sill for the vehicle jack .
.,.. Turn the
vehicl e jack located under the lifting
point on the si ll to raise the jack until the jaw
<=> fig. lBO @cove rs the n o tch on the vehicle
r=> ,& ¢0.
.,.. Align the vehi cle jack so the jaw @covers the
notch and the base plate @ is f lat on the floor.
The base plate @ must be
vertical under the
lifting point @.
.,.. Install the rod on the veh icle jack: Insert the
rod into the opening on the handwheel. Turn
the rod left or right to secure it.
Em erg en cy ass is tan ce
.,.. Continue raising the jack wit h the rod unt il the
wheel lifts off the ground slightly.
Position t he vehicle jack
only under the designat­
ed lifting points on the si ll
r:1>fig. 179. The re is ex­
actly
one l ocation fo r each wheel. The jack must
not be posit ioned at any other location
r=> ,& r:=>0 .
Soft ground under the jack can cause the veh icle
to s lip off the jack. A lways place the jack on firm
ground. Use a flat, stable support if necessary.
Use a non-slip surface suc h as a rubber mat on a
slipper y surface such as tile.
_& WARNING
--You or your passengers could be injured
while changing a wheel if you do not follow
these safety precautions:
- Position the vehi cle jack on ly at the desig­
nated lifting points and a lign the jack.
Otherwise, the vehicle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack .
Always provide a f irm base for the jack on
the g round. If necessary, use a sturdy
board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slipp ing .
- To help prevent injury to yourself and your
passengers:
- Do no t ra ise the vehicle until you are s ure
the jack is secure ly engaged.
- Passengers must not remain in the veh icle
when it is jacked up .
- Make sure tha t passengers wait in a safe
pla ce away from the veh icle and we ll away
from the road and traffic.
- Make sure jack pos ition is cor rect, adjus t
as necessary and then contin ue to raise
the jack .
(D Note
Do not lift the vehicle by the sill. Posi tion the
vehicle j ack only at the des igna ted lifting
221

Emergency assistance
points on the sill. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing a wheel
Follo w these instructions step-by-step for chang­
ing the wheel.
Fig. 181 Changing a wheel: using the screwdrive r handle
(with the blade removed) to turn the bolts
Fig. 182 Changing a wheel: alignment pin insid e the top
hole
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing the wheel
.. Remove the topmost wheel bolt completely
with the
hexagonal socket in the screwdriver
handle (vehicle tool kit)
¢fig . 181 and set it
aside on a
clean surface.
.. Screw the threaded end of the
alignment pin
from the tool kit hand-tight into the empty bolt
hole
¢fig. 182 .
.. Then remove the other wheel bolts as described
above .
.. Take off the wheel leaving the alignment pin in
the bolt hole
c::;, (D.
222
Putting on the other wheel
.. Push the wheel over the alignment pin .
.. Screw on the wheel bolts and tighten them
slightly using the hexagonal socket .
.. Remove the alignment pin and insert and tight­
en the remaining wheel bolt slightly like the
rest .
.. Turn the jack hand le counter-clockwise to lower
the vehicle until the jack is fully released .
.. Use the wheel bolt wrench to tighten all wheel
bolts firmly
c::;, page 220. Tighten them in a
crisscross pattern,
from one bolt to the (ap­
proximately) opposite one, to keep the wheel
centered .
.. Perform the steps required after changing the
wheel
c::;, page 219, A~er changing a wheel.
The hexagonal socket makes it easier to remove
the wheel bolts from the rim. Care should be tak­
en when removing the reversible blade.
(D Note
When removing or installing the wheel, the
rim could hit the brake rotor/ceramic brake
rotor* and damage the rotor. Work carefully
and have a second person to help you.
(D Tips
- When mounting tires with unidirectional
tread design
make sure the tread pattern is
pointed the right way
c::;, page 223.
- The wheel bolts should be clean and easy to
turn. Check for dirt and corrosion on the
mating surfaces of both the wheel and the
hub. Remove all dirt from these surfaces be­
fore remounting the wheel.
- Do not use the hexagonal socket in the
screwdriver handle to loosen or tighten the
wheel bolts .

"' N
0:: l­oo
rl I.O
"' N
"' rl
Fu se pa nel @ (black )
No. Consumer
1 Dynamic steering
2 Electron ic Stabilization Control (module)
A/C system pressure sensor, electrome-
chanical parking brake, HomeLink, auto-
3 mat
ic dimming interior rear view mirror,
air quality/outside air sensor, Electron ic
Stabilization Control (button)
s Sound actuator
6 Headlight range control/headl
ight (corner-
ing light)
7 Headlight (cornering light)
Control modu les (electromechanical park-
8 ing brake, shock absorber, q uattro sport),
DCDC converte r
9 Adaptive
cruise control
10 Shift gate/clutch sensor
11 Side assist
1 2 Headlight range cont ro l, parking system
13 Airbag
14 Rear
wiper (a llroad)
15 Auxiliary fuse (instrument panel)
16 Auxiliary
fuse termina l 15 (engine area)
Fuse p anel @ (brown )
No. C onsumer
2 Brake light sensor
3 Fuel pump
4 Clutch sensor
5
Left seat heating with/without seat venti-
lation
6 Electronic Stabilization Control (electric)
7 Ho rn
8
Front left door (window regulator, central
locking, mirror, switch, lighting)
9 Windshield wiper motor
10 Electronic Stabilization Control (valves) Fu
ses a nd bulb s
No. Consumer
Two-door mode ls: rear left window regula-
11 tor; Four-door
models: rear left door (win-
dow regulator, central locking, switch,
light ing)
12 Rain and l
ight sensor
Fuse panel © (r e d )
No . Con sumer
3 Lumbar support
4 Dynamic steering
5 Inter
ior l ight ing (Cabriolet)
6 Windshie
ld washer system, headlight
washer system
7 Vehicle electrica l system control module 1
8 Vehicle electr ica l system control module 1
9 Left rear
window regulator motor (Ca brio-
let)/su nroof
10 Vehicle electr ica l system co ntrol module 1
11 Right rear
window regulator (Cabriolet)/
sun shade motor
12 Anti-theft
alarm warning system
Right cockpit fuse assignment
Fig. 185 Right cockpit: fu se panel with plastic cl ip
225

Fuses and bulbs
Fuse panel @ (black )
No. Consumer
5 Steering col
umn switch module
7 Term inal 15 d iagnost ic connector
8 Gateway (Databus diagnostic interface)
9 Supplementary heater
Fuse panel@ (brown )
No. Consumer
1 CD/ DVD p laye r
2 Wi-Fi
3 M
MI/Radio
4 Instrument cluster
5
Gateway (ins trument cluster co ntrol mod-
ule)
6 Ignition lock
7 Ligh t swi tch
8 Climate control system blower
9 Steering col umn lock
10 Climate contro l system
1 1 Te
rm inal 30 d iagnost ic connector
12 Steer ing column sw itch module
226
Right luggage compartment fuse
assignment
Fig. 186 Right lu ggage compartment: f use pane l w it h
plast ic clip
Fuse panel @ (black )
No . Consumer
2 Rea r window heater (Cabriole t)
3 Power top latch (Cabriolet)
4 Power top hyd raulics (Cabr io let)
Fuse panel @ (black)
No . Consumer
Luggage compartment lid con trol mo dule
1 (all road)/Powe r top cont ro l modu le (Cab-
r iolet)
2 Retractable rear
spoiler
(RS 5 Coupe)
5 Elec tromechan ica l pa rking brake
6 Electronic damping control
7 Elec tromech anica l par king brake
8 Rear exterior lig hti ng
9 qu attro sport
10 Rear exter ior lighting
1 1 Cent
ral locking
12 Term inal 30

M N
0:: l­oo ,...., \!) 1.1'1
N 1.1'1 ,....,
Fuse panel© (brown)
No. Consumer
1 Luggage compartment lid control module
(allroad)
2 12-volt socket, cigarette lighter
3 DCDC converter path 1
4 DCDC converter path 2, sound amplifie r,
rad io
6 Right upper cabin heating (Cabriolet)
7 Electromechanical parking brake
9
Right front door (window regulator, cen-
tral locking, mirror, switch, lighting)
10 Left upper cabin
heating (Cabriolet)
Two-door models: rear right w indow regu-
11 lator; Four-door models: rear
right door
(window regulator, central locking, switch,
lighting)
12 Cell phone prep
Fuse
panel © (black)
No. Consumer
1 Right front seat heating
4 MMI
5 Radio
6 Rear view camera
7 Rear window heater (allroad)
8 Rear
Seat Entertainment
Bulbs
Replacing bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you .
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases , other parts of the car must first be re­
moved before you are ab le to get to the bulb .
This applies especially to the light bulbs in the
front of you r ca r which you can only reach
through the engine compartment .
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, parts must be
Fuses and bulbs
correct ly taken apart and then properly put back
together to help prevent breakage of parts and
long term damage from water that can enter
housings that have not been properly resealed.
For your safety, we recommend that you have
your authorized Audi dea ler replace any bulbs for
you, since your dealer has the proper tools, the
correct bulbs and the expertise.
Gas discharge lamp s (Xenon lights)*:
Due to the high electr ical voltage, have the bulbs
replaced by a qualified technician . Head lights
with Xenon light are identified by the high volt­
age sticker.
A WARNING
Changing Xenon lamps without the necessary
equipment can cause serious personal injury.
- Bulbs are pressurized and can explode when
being changed . Potential risk of injury!
- On vehicles equipped with gas discharge
bu lbs (Xenon light) * life -threatening injuries
can result from improper handling of the
high -vo ltage portions of such lamps!
-On ly your authorized Audi dealer or quali­
fied workshop shou ld change the bulbs in
gas discharge lamps. There are parts with
sharp edges on the openings and on the
bulb holders that can cause serious cuts . If
you are uncertain about what to do, have
the wor k performed by an autho rized Audi
dealer or qualified workshop. Serious per­
sonal injury may result from improperly per­
formed work .
(D Tips
-If you st ill prefer to replace the light bulbs
yourself, be aware that the eng ine compart­
ment is a hazardous area to work
inq page 187 q &..
-It is best to ask your authorized Audi dealer
whenever you want to change a bulb.
227