towing AUDI S3 2010 User Guide

[ i] Tips
• Do not tow a trailer during the break-in period of your vehicle.
• If you tow a trailer, your Audi may require more frequent mainte ­
nance due to the extra load=> page 299 . •
Parking on a slope
-----------------
Do not park with a trailer on a slope. If it cannot be
avoided, do so only after doing the following:
When parking:
-Apply the foot brake.
- Have someone place chocks under both the vehicle and the trailer wheels .
- With chocks in place, slowly release the brakes until
wheel blocks absorb the load.
- Turn the wheels towards the curb.
- Apply the parking brake.
- Place an automatic transmission in
P, respectively a
manual transmission in first or reverse gear.
When restarting after parking:
- Start the engine.
- Shift transmission into gear.
- Release the parking brake and slowly pull out and away from the wheel blocks.
- Stop and have someone retrieve the wheel blocks.
Controls and equip­
ment Safety first Vehicle operation
Trailer towing
[
i] Tips
If you move the selector lever of the automatic transmission to P
before applying the parking brake and before blocking the wheels,
you may have to use more force later to move the lever out of the
P
position .•
Vehicle care Do-it-yourself service Technical data

-Tires and wheels
Steps for Determining Correct
Load Limit
1. Locate the statement "THE COMBINED
WEIGHT OF OCCUPANTS AND CARGO
SHOULD NEVER EXCEED XXX KG OR XXX LBS"on your vehicle's placard (tire infla­
tion pressure label)~ page 246, fig. 173.
2. Determine the combined weight of the driver and passengers that will be riding
in your vehicle.
3. Subtract the combined weight of the driver and passengers from "XXX" kilo­
grams or "XXX" pounds shown on the
sticker ~ page 246, fig. 173.
4. The resulting figure equals the available amount of cargo and luggage load
capacity. For example, if the
"XXX"
amount equals 1400 lbs. and there will
be five 150 lbs. passengers in your
vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400-750 (5
X 150) = 650 lbs.) 5. Determine the combined weight of
luggage and cargo being loaded on the
vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.
6. If your vehicle will be towing a trailer, load from your trailer will be transferred
to your vehicle. Consult this manual to
determine how this reduces the avail­
able cargo and luggage load capacity of
your vehicle.
- Check the tire sidewall (~ page 254,
fig. 177) to determine the designated load rating for a specific tire. •

1111...__W_ h_ a _ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
What do I do now?
Jack, tools and spare wheel
Jack and tools
The tools and jack are stored underneath the floor panel
in the luggage compartment.
Raise the floor panel with the loop.
Fig. 181 Floor panel
hung on the bottom of
the luggage compart­
ment cover
Fig . 182 Vehicle tool
kit and jack
- Hang the loop on the underside of the luggage compart­
ment cover ~ fig. 181.
Remove the tool kit or the jack.
The onboard tool kit includes:
• Hook for removing wheel covers*
• Plasti c hook to remove wheel bolt covers
• Wheel bolt wrench
• Alignment pin for changing wheels
• Screwdriver with reversible blade
• Towing eye
Before storing the jack, make sure it is wound back down as far as it
will go.
After use, the jack and tools must be put back in place underneath
the floor panel in the luggage compartment.
Note: some of the on-board items listed above are provided on
certain models only or are optional extras.
& WARNING
Improper use of the vehicle jack can cause serious personal inju­
ries.
• Using a bumper jack to raise the vehicle will damage the
bumper system. The jack may slip, causing injury.
• Never support your vehicle on cinder blocks, bricks or other
objects. These may not be able to support the load and could
cause injury when they fail.
• Never start or run the engine while the vehicle is supported by
the jack.
• If you must work under the vehicle, always use safety stands
specifically designed for this purpose.
• Never try and use the hexagonal socket
in the handle of the
screwdriver to loosen or tighten the wheel bolts.

What do I do now? -__________________ __;__:....:....:..:: __ _
•
-All passengers should leave the car and move to a safe
location (for instance, behind the guardrail)~& .
- Apply the
parking brake firmly ~& .
- Move
selector lever to position Pon an automatic trans-
miss ion; put manual transmission in
first gear ~& .
-If you are towing a trailer : unhitch the trailer from your
vehicle.
- Take the
tool and the spare tire~ page 268 out of the
luggage compartment.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flasher on and use other warning
devices to alert other motorists.
• Make sure that passengers wait
in a safe place away from the
vehicle and well away from the roadway and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed. When one
front wheel is lifted off the ground, placing the automatic trans­
mission in "P" (Park), or engaging a gear in a manual transmission
will
not prevent the vehicle from moving.
• Before you change a wheel, be sure the ground is level and firm.
If necessary, use a sturdy board under the jack.
• After installing the spare wheel, make sure that you remount
the flat tire/wheel in its storage area properly and tighten the
knurled retaining screw securely. •
Changing a wheel
When you change a wheel, follow the sequence described
below step-by-step and exactly in that order.
1. Remove the decorative wheel cover*. For more details
see also
~ page 272, "Decorative wheel covers" or
~ page 273, "Wheels with cap-covered wheel bolts".
2. Loosen the
wheel bolts~ page 274.
3. Locate the proper mounting point for the jack and align
the jack below that point~
page 274.
4. Lift the car with the jack~ page 274.
5. Take the flat wheel off and then put the spare on
~ page 276.
6. Tighten all wheel bolts lightly .
7.
Lower the vehicle with the jack .
8. Use the wheel bolt wrench and
firmly tighten all wheel
bolts ~
page 274.
9. Put the decorative wheel cover* back on.
& WARNING
Always read and head all WARNINGS and information ::} & in
"Raising the vehicle" on
page 274 and ~ page 277. •
After changing a wheel
A wheel change is not complete without the following
actions.
- Store and secure the replaced wheel in the spare wheel
well. .,._
Do-it-yourself service

________________________________________________ E_m _ e_r..:: g ~ e_ n_c__, y:._ s_ i_ t ..:u ;..:a:.:. t.:.. i..: o :..; n..:..:: s __ ffllll
•
Emergency situations
General
This chapter is intended for trained emergency crews and working
pe rsonnel who have the necessary tools and equ ipment to perform
these operations. •
Starting by pushing or towing
(D Note
Vehicles with an automatic transmis sion cannot be started by
push ing or towing . •
Starting with jumper cables
Ju mpe r cabl e: Note the man ufa ct ure r's in for matio n.
If the battery is discharged, another veh icle can provide starting
assistance. For this you require a jumper cable. Both batteries must
h ave t he same vo ltage (V) and a s im ilar capacity (Ah).
Jumper cables
Use
only jumper cables of sufficiently large cross section to safely
car ry the starter current . Refer to the manufactu rer's specifications.
Use only j um per ca bles with
isolated term in al cl am ps and pr operly
marked for distinction :
plus
(+) cable in mo st c ases c olored red
minus( -) cable i n most cas es co lor ed black .
T he wire cross section must be at least 0 .038 in
2 (25 mm2
) for gaso ­
l ine e ngines and a t lea st 0.054 in
2 (35 mm2
) fo r diese l e ng ines .
& WARNING
Batteries contain electricity, acid , and gas. Any of the se can cause
very ser ious or fatal injury . Follow the instructions below for safe
handling of your vehicle 's battery .
• Always shield your eyes and avoid leaning over the battery
whenever possible .
• A discharged battery can already freeze at temperatures just
below 32 °F (0 °C l. Never attempt to provide starting assistance on
a frozen or thawed out battery- Danger of explosion and chemical
burns! Replace a battery if it has been frozen.
• Do not allow battery acid to contact eyes or skin. Flush any
contacted area with water immediately .
• Improper use of a booster battery to start a vehicle may cause
an explosion .
• Vehicle batteries generate explosive gases . Keep sparks, flame
and lighted cigarettes away from batteries .
• Do not try to jump start any vehicle with a low acid level in the
battery .
• The voltage of the booster battery must also have a 12 -Volt
rating . The capacity (Ah ) of the booster battery should not be
lower than that of the discharged battery . Use of batteries of
different voltage or substantially different "Ah " rating may cause
an explosion and personal injury .
• Never charge a frozen battery . Gas trapped in the ice may cause
an explosion.
• Never charge or use a battery that has been frozen . The battery
case may have be weakened .
• Use of batter ies of different voltage or substantially different
capacity (Ah) rating may cau se an e xplosion and inju ry . The
c apacity (Ah ) of the booster battery should not be lower than that
of the discharged battery. .,.
Do-it -yourself service

11111.___E_ m _ e _r-==g :...e_ n_ c...:y _ s_ i_t _u _a _t_ i_o _n_ s _______________________________________________ _
13. Disconnect the cable while the engine is running exactly
in
reverse order to that described in~ page 287,
11Connecting/disconnecting the jumper cable.11
• When
doing so, make sure that the cable cannot contact rotating engine parts.
14. Turn the heater blower and the rear window heating off again.
The battery is vented to the outside to prevent gases from entering
the vehicle interior.
Make sure that the jumper clamps are well connected with their
metal ports in full contact with the battery terminals .
& WARNING
To avoid serious personal injury and damage to the vehicle, heed
all warnings and instructions of the jumper cable manufacturer. If
in doubt, call for road service.
• Jumper cables must be long enough so that the vehicles do not
touch .
• When connecting jumper cables, make sure that they cannot
get caught in any moving parts in the engine compartment.
• Before you check anything in the engine compartment, always
read and heed all WARNINGS =>
page 215, "Engine compartment" .
0 Note
Improperly connected jumper cables can damage or destroy the
generator.
• Do not use the battery negative terminal for jump starting or a
malfunction could occur in the vehicle electrical system.
• Always connect POSITIVE(+) to POSITIVE(+), and NEGATIVE( -) to
NEGATIVE (-l terminal. •
Check that all screw plugs on the battery cells are screwed in
firmly. If not, tighten plugs prior to connecting clamp on negative battery terminal.
• Please note that the procedure for connecting a jumper cable as
described above applies specifically to the case of your vehicle
being jump started. When you are giving a jump start to another
vehicle, do
not connect the minus(-) cable to the minus 1-l terminal
on the discharged battery@=>
page 287, fig. 196. Instead, securely
connect the minus(-) cable to either a massive metal component
that is firmly bolted to the engine block or to the engine block itself.
If the battery that is being charged does not vent to the outside,
escaping battery gas could ignite and explode! •
Emergency towing with commercial
tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by commercial tow truck
operators who know how to operate their equipment safely.
• Never tow your Audi, towing will cause damage to the engine
and transmission.
• Never wrap the safety chains or winch cables around the brake
lines.
• To prevent unnecessary damage, your Audi must be transported
with a car carrier (flat bed truck).
• To load the vehicle on to the flat bed, use the towing loop found
in the vehicle tools and attach to the front or rear anchorage
=>
page 289 and => page 289 . .,_

________________________________________________ E_ m_ e_r ,,::g c..e_ n _ c..::y;._ s_ i_t _u _a_ t_ i_o _n_ s _ ___.ffllll
& WARNING
A vehicle being towed is not safe for passengers. Never allow
anyone to ride in a vehicle being towed, for any reason. •
Front towing loop
Do not install the front towing loop until it is needed.
Fig. 197 Front
bumper : removing the
cover cap
Fig . 198 Front
bumper : screwing in
the towing loop
The towing loop fits into the threaded hole located on the
right side of the front bumper and covered by a small cover
when not in use. Note that the towing loop has a
left-hand
thread !
-Remove the towing loop from the vehicle toolkit
=:>
page 268.
- Press on the bottom edge of the cover cap to disengage
and take it out of the bumper. The cap remains
connected to the bumper =:> fig. 197.
- Insert the towing loop into the threaded hole=:> fig. 198
and turn it all the way in until it is seated securely, then
tighten it with the wheel bolt wrench.
When it is no longer needed, unscrew the towing loop and put it
back into the on-board toolkit. Make sure to have the towing loop
stored in the vehicle at all times.
& WARNING
If the towing loop is not screwed in as far as it will go, the thread
can pull out when the vehicle is towed -potential risk of an
accident. •
Rear towing loop
Do not install the rear towing loop until it is needed.
Fig. 199 Rear bumper:
cover ....
Vehicle care Do-it-yourself service irechnical data

IIII...__E_ m_ e_ r -'g==-- e_n _ c_ y=--- s_ i_ t _u _a _ t_ i_o _n _ s _____________________________________________ _
Fig. 200 Rear bumper:
towing loop inserted
On the right side of the rear bumper there is a threaded hole
for the towing loop. The threaded hole is behind a cover.
Note that the towing loop has a left-hand thread!
Remove the towing loop from the vehicle toolkit
~ page 268.
Place the screwdriver against the upper edge of the
cover and carefully pry it out~
page 289, fig. 199.
- Insert the towing loop into the threaded hole~ fig. 200
and turn it all the way in until it is seated securely, then
tighten it with the wheel bolt wrench.
When it is no longer needed, unscrew the towing loop and put it
back into the vehicle toolkit. Be sure to have the towing loop stored in the vehicle at all times.
& WARNING
If you do not screw the towing loop completely, it could come out
of the threaded hole while the vehicle is being towed causing
damage to the vehicle and possible serious personal injury. •
Loading the vehicle onto a flat bed truck
Front
hook up
N
"' :? 0:. .,
"'
Fig. 201 Vehicle on flat
bed truck
-Align the vehicle with the centerline of the car carrier
ramp.
- Attach the winch hook to the front towline eye
~ page 289, fig. 198 previously installed.
Rear hook up
-Align the vehicle with the centerline of the car carrier
ramp.
- Attach the winch hook to the rear towline eye~ fig. 200
previously installed.
[ i] Tips
Check carefully to make sure the hook -up is secure before moving
the car up the flatbed truck ramp. •

Consumer Information I'll _________________________________ __::..::....:...:...::...:.:..:....:....:.:;__ _____ _
Maintenance
General
Your vehicle has been designed to help keep maintenance require­
ments to a minimum.
However, a certain amount of regular maintenance is still necessary
to assure your vehicle's safety, economy and reliability.
For detailed vehicle maintenance consult your Warranty
& Mainte­
nance booklet.
Under difficult operating conditions, for example at extremely low
outside temperatures, in very dusty regions, when towing a trailer
very frequently, etc., some service work should be performed
between the intervals specified. This applies particularly to:
• oil changes, and
• cleaning or replacing the air filter.
ci> For the sake of the environment
By regularly maintaining your vehicle, you help make sure that emis­
sion standards are maintained, thus minimizing adverse effects on
the environment. •
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated fuel injection and
emission control systems, and the generally increasing technical
complexity of today's automobiles, have steadily reduced the scope
of maintenance and repairs which can be carried out by vehicle
owners.
Also, safety and environmental concerns place very strict
limits on the nature of repairs and adjustments to engine and trans­
mission parts which an owner can perform.
Controls and equip­
ment Safety first Vehicle operation
Maintenance, adjustments and repairs usually require special tools,
testing devices and other equipment available to specially trained
workshop personnel in order to assure proper performance, reli­ ability and safety of the vehicle and its many systems.
Improper maintenance, adjustments and repairs can impair the
operation and reliability of your vehicle and even void your vehicle
warranty. Therefore, proof of servicing in accordance with the main­ tenance schedule may be a condition for upholding a possible
warranty claim made within the warranty period.
Above all, operational safety can be adversely affected, creating unnecessary risks for you and your passengers.
If in doubt about any servicing, have it done by your authorized Audi
dealer or any other properly equipped and qualified workshop. We
strongly urge you to give your authorized Audi dealer the opportu­
nity to perform all scheduled maintenance and necessary repairs.
Your dealer has the facilities, original parts and trained specialists
to keep your vehicle running properly .
Performing limited maintenance yourself
The following pages describe a limited number of procedures which
can be performed on your vehicle with ordinary tools, should the
need arise and trained personnel be unavailable. Before performing
any of these procedures, always thoroughly read all of the appli­
cable text and carefully follow the instructions given. Always rigor­
ously observe the
WARNINGS provided.
Before you check anything in the engine compartment, always read
and heed all WARNINGS=>
& and=> & in "Working in the engine
compartment" on
page 224.
& WARNING
• Serious personal injury may occur as a result of improperly
performed maintenance, adjustments or repairs.
Vehicle care Do-it-yourself service Tec hn ica l da ta

______________________________________________ A_ l_,_ p _h_ a_ b_e _t_ic _ a _ l _in _ d_e _ x __ lll
Cornering light ..... ... .. ... ..... ... . 55
Cruise contro l ... .... ....... ........ 110
Changing speed . .... ............. 111
Presetting your speed ............. 111
Switching off .... .... .... ... .... . 112
Switching on .... .... .... ....... . 110
Warning /indica tor ligh ts .. .. .... .... 14
Cup holder .. .... ....... .... .. . ...... 90
Cup holders
front ... .... .... .... .... ..... .. ..
89
Current fuel mil eage . ........ ...... .. . 22
D
Data .. ... ... .... .... .... .... ...... 296
Data recorder . ..... .. .. .... .... .... . 188
Date display . ...... ...... ... ... ... .... 9
Daytime running lights ...... .......... 53
Daytime running lights (Canada) .. .. .. . 53
Declaration of compliance
Cell phone package .. ...... .......
302
Elec tronic immobilizer ............ 302
Homelink ® universal remote control 302
Remote control key .. .... .... .... . 302
Tire pressure monitoring system ... 302
Declarat ion of con form ity ..... .. ... .. 267
def
What does this mean when it appears in
the trip odometer display? .... .... .
10
Defective light bulb warning ...... .... . 34
Defogging the windows .......... .... . 99
Defrosting the windows .. .... .... ..... 99
Defrosting /defogging windows .. .... ..
102
Controls and equip­ ment Safety first
Determining
correct load limit ... .. .. . 251
Diesel engine
Adding engine oil ......... .... ...
231
Changing engine oil ....... ... .... 23 1
Engine oil .... ... .... .... .... .... 231
Diesel fuel .......... .... .... ... .... 218
Diesel particulate filteir ............ 32 , 197
Digital clock .... ... .... .... .... ... .. .. 9
Setting the time ..... ...... ....... .. 9
Digital compass ..... ... .... .... .... ..
70
Dim ensions ........... ........ .... . 295
Dipstick
Reading the dipstick properly . .....
229
Direct Shift Gearbox
Emergency release ..... .. ....
120, 121
Dis tance ....... ....... .... ....... .. . 23
Doors, power locks ... .. .... ...... .... 41
Driver information .................... 29
Driver Information System
Menu d isplay . .... .... .... ... .... .
23
Driver information system
Gearshift indicator .. ... ............
19
Menu button ...... .... ............ 25
Open door or front lid warning . ... .. 18
Outside temperatu ire disp lay . ...... . 18
Red symbols . .... ..... .. .... .... .. 28
Service interval display .... .... .... . 20
Setting ..... .. ...... ......... .... . 26
Sound system display . ....... .... .. 18
Trip compute r ....... ..... .. . .... . 22
yellow symbols .. .... ... ... .. ..... 29
Driver seat
See S eat ing position .. .... .... .... 126
Driving safely . .... .. . .... .... ..... .. 124
Driving through water .... ... .... .... . 196
Duplicate key ............. .... ... .. .. 36
E
Elapsed time ...... ........ .... ... ... 22
Electrically heat ed front seats .... ... .. 104
Electro-mechanica l power assist . ... 16, 193
Electronic diff erential lock
Warning/indicator lights ...... ......
16
Electronic differential lock (EDU
How the system works .... .... ....
189
Electronic immobilizer ....... .... .. 10, 38
Electronic pow er control
EPC warning/indicator light .........
13
Electronic speed limiter .. ... ... .... ... 21
Electronic Stability Program .. .... ... .
188
Electronic stabiliza tion program (ESP)
Warning/indicator lights .... ...... ..
13
Eme rgency flasher
Warning /indicator lights .. .. .... ... .
14
Emergency flashers .. .... ... ... .. .... . 56
Emergency operat ion
panoramic sliding sunroof . .... .... .
50
Rear lid .. .. .. .... ..... .. .... ..... 44
Emergency release for selector lever . . 120,
121
Emergency starting .. .... .... .... .... 285
Emergency towing ...... .... .... .... 288
Vehicle operation Vehicle care Do-it-yourself service Technical data