light AUDI TT COUPE 2016 User Guide

Downloaded from www.Manualslib.com manuals search engine ..... N
a:
@ Tips
For additional information on ESC and ABS,
refer to ¢page 87.
BRAKE! .. (USA models) I rl] (Canada models)
Brake pads!
If the warning light turns on, immediately con­
tact your authorized Audi dealer or authorized
Audi Service Facility
to have all brake pads in­
spected . Both sets
of brake pads on an axle must
always be replaced at the same time.
A WARNING
Driving with bad brakes can cause a collision
and serious personal injury.
-
If the rl] warning light or the .. warning
light l) with the message Brake pads!
comes on in the instrument cluster display,
immediately contact your authorized Audi
dealer
or authorized Audi Service Facility to
have all brake pads checked or replaced if
necessary.
ffl;f !f Safety systems
-1
The II (USA models) Im (Canada models) indi­
cator
light monitors the safety systems.
Safety system
If the II (USA models) Im (Canada models) in­
dicator
light turns on or blinks, there is a mal­
function in a safety system.
Drive
to an authorized Audi dealer or authorized
Audi Service Facility immediately
to have the
malfunction corrected.
A WARNING
-Have the safety systems inspected immedi-
ately. Otherwise, there
is a risk that the sys­
tems may not activate during a collision,
which increases
the risk of serious injury or
death.
co ..... .....
:=: 1) - : USA models only
Instruments and indicator lights
~ Engine control
If the II indicator light turns on if there is a mal­
function in
the engine control.
Drive slowly
to an authorized Audi dealer or au­
thorized Audi Service Facility
to have the engine
checked .
o System indicator light (MIL)
The system indicator light (MIL) is part of the On
Board Diagnostic system (OBD II). The ¢.j sym­
bol turns on when the ignition is switched on and
turns
off again once the engine is started and
running
at a steady idle speed. This indicates that
the MIL is functioning correctly.
The indicator
light turns on if there is a malfunc­
tion in the engine electronics. See an authorized
Audi dealer or authorized Audi Service Facility
to
have the malfunction corrected.
For additional
information, refer to¢ page 17.
!?\Engine speed limitation
Applies to vehicles wit h en gi ne speed lim itation
(I! Maximum engine speed: XXXX rpm
The engine speed is automatically limited to the
speed displayed in the driver information system.
This protects
the engine from overheating.
The engine speed
limitation deactivates once the
engine is no longer in the critical temperature
range and you have released the accelerator ped­
al once.
If the engine speed limitation was activated by
an engine
control malfunction, the II indicator
light also turns on. Make sure the engine speed
does
not go above the speed displayed, for exam­
ple when downshifting. Drive
to an authorized
Audi dealer or authori z
ed Audi Service Facility im­
mediately to have the malfunction corrected.
~ Engine oil level (min.)
II Please check oil level
15

Downloaded from www.Manualslib.com manuals search engine Instruments and indicator lights
You may continue driving for the time being.
Check the engine oil level as soon as possible
<:!)page 239.
-If the engine oil level is too low, add engine o il
<:!)page 240.
-If the engine oil level is correct and the indica­
tor light still turns on, drive at low engine
speed to an authorized Audi dealer or author­
ized Audi Service Facility.
X;:';,,, Engine oil sensor
• Oil le vel system: malfunction! Please con·
tact Service
The sensor to check the engine oil level has
failed. Drive to an authorized Audi deale r or a u­
thorized Audi Service Facility immediately to have
the malfunction corrected.
[JlJ Tank system
D Ple a se r efuel
If the indicator light turns on for the first time
and the message appears, there are about 1.9
gal (7 L) of fuel left in the tank.
D Plea se refuel immediately
If t he indicator lig ht turns on the message ap­
pears, the fuel tank is almost empty. Refuel the
vehicle immediately.
D Tank sy ste m : malfun ction! Please contact
Servic e
If the indicator light t urns on and this message
appears, there is a malfunction in the tank sys­
tem.
Drive to an author ized Audi dealer or authorized
Audi Serv ice Facility immediately to have th e
malfunction corrected.
@l For the sake of the environment
Fuel should never enter the sewer system or
come into contact w ith the ground.
(Di Tips
More information on refueling is available on
page¢ page 232.
16
· ,_Washer fluid level
m Pleas e add washer fluid
Fill the washer fluid for the windshield washer
system and the headlight washer system* when
the ignit ion is switched off<:!) page 248.
\9 ! Windshield wipers
@Windshield wiper s: malfunction! Plea se
conta ct Servi ce
There is a malfunction with the windshield wip­
e r
s.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
-:q>.-Bulb failure indicator
If the II indicator light turns on, a bulb has
failed. The message indica tes the location of the
bulb.
Replace
the bu lb immediately .
Vehicle lights: malfunction! Please contact
Service
There i s a malfunction in the headlights or the
light switch. Drive to an authorized Audi dealer or
authorized Aud i Serv ice Facility immediately to
have the malfunction corrected.
&. WARNING
-Light bulbs are under pressure and can ex·
plode when bulbs are replaced, whic h in­
creases the risk of injury.
-
With gas-discharge lamps* (xenon head­
lights), the high-vo ltage component must
be handled appropriately. Otherwise, there
is a risk of fatal injury.
~CD Headlight range control system
II Headlight range control: malfunction! See
owne
r's manual
There i s a mal f u nction in the headlight range
control system, which may cause glare for other
drive rs. .,..

Downloaded from www.Manualslib.com manuals search engine Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
~O Audi adaptive light
Applies to: vehicles with Audi adaptive light
rJJ Audi adaptive light: malfunction! See own­
er's manual
There is a malfunction in the adaptive lights. The
headlights still function.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
li,D Light/rain sensor
El Automatic headlights: malfunction! See
owner's manual
II Automatic wipers: malfunction! See owner's
manual
The light/rain sensor is malfunctioning.
The low
beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. You can continue to turn the
lights on and off using the light switch. You can
still control all wiper functions that are inde­
pendent of the rain sensor.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
; Damper control
App lies to: vehicles with Audi drive select
R Suspension: malfunction! You may continue
driving
There is an adaptive damper malfunction.
Drive to an authorized Audi dealer or authorized
Audi Service Facility immediately to have the
malfunction corrected.
Instruments and indicator lights
¢ Q Turn signals
If the. or B indicator light blinks, a turn sig­
nal is turned on. If both indicator lights are blink­
ing,
the emergency flashers are on.
In
an indicator light blinks twice as fast as usual,
then a turn signal bulb has failed. Replace the
bulb immediately.
CJ! 4f. Rear safety belt
Applies to: vehicles with rear safety belt detection
The respective indicator light will turn on briefly
when a safety belt on the rear seats is fastened
or unfastened.
f!l-If this indicator light turns on briefly, the
safety belt on the rear seat is not fastened.
II-If this indicator light turns on briefly, the
safety belt on the rear seat was fastened.
·-If this indicator light blinks, the safety belt
was unfastened while driving. Above a certain
speed, there will also be a warning tone.
(D Tips
For additional information on safety belts, re­
fer to ~page 180.
On-Board Diagnostic
system (OBD)
System indicator light (MIL)
The system indicator light (MIL) Ill in the instru­
ment cluster is part of the On Board Diagnostic
System (OBD II).
The
warning/indicator light turns on when the ig­
nition is
switched on and turns off once the en­
gine is started and is running in idle at a stable
speed. This indicates that the MIL is functioning
correctly.
If the light does not turn off after starting the
engine or turns on while driving, this may indi­
cate there is a malfunction in the engine. If the
indicator turns on, the catalytic converter may be
damaged. ..,.
17

Downloaded from www.Manualslib.com manuals search engine Instruments and indicator lights
Drive with reduced engine performance (avoid
high
speeds for extended periods of time and/ or
fast acceleration) and have the malfunction cor­
rected. See an authorized Audi dealer or author­
ized Audi Service Facility.
The
indicator may turn on if the electronic speed
lim iter is faulty. For additional information, refer
to c:> page 72, Electronic speed limiter.
On-Board Diagnostics
Fig. 4 Locat ion of Data Link Connector (DLC)
On-Board Diagnostics monitors the components
of your emission control system. Each monitored
component in your engine system has been as­
signed a code. In case of a malfunction, the com-
18
ponent will be identified and the fault stored as a
code in the control module memory.
The MIL light may also illum inate if there is a
l
eak in the on-boar d fuel vapor recovery system.
If the light illuminates after a refuelling, stop
the vehicle and make sure the fuel filler cap is
properly closed c:> page 233.
In order to make an accurate diagnosis, the stor­
ed data can only be displayed using special d iag­
nostic equipment (generic scan tool for OBD).
In order to connect the special diagnostic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release c:> fig. 4.
Your authorized Audi dealer or a qualified service
station can interpret the code and perform the
necessary repair.
11. WARNING
Do not use the diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a colli­
sion!
- I

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
Driver information system
Overview
Fig. S Driver information system diagram: classic view
Fig. 6 Dri
ver in formation system diagram : expanded view
The driver information system displays various
items:
(!) Tachometer
@ Left additional display (divided in two sec-
tions in
the expanded view)
@ Tab area
@ Central area
® Status line (displayed on one or two lines)
@ Right additional display (divided in two sec-
tions in the expanded view)
A WARNING
Do not assume the roads are free of ice based
on
the outside temperature display. Be aware
Driver information system
that there may be ice on roads even when the
outside temperature is around 41 °F (+ S 0()
and that ice can increase the risk of accidents.
(0 Tips
-You can select the units used for tempera­
ture, speed and other measurements in
the
Infotainment system.
-
If your vehicle is stationary or if you are driv­
ing
at very low speeds, the temperature dis­
played may
be slightly higherthan the ac­
tual temperature outside due to the heat ra­
diating
from the engine .
-
At temperatures below 41 °F (+S 0(), a
snowflake symbol appears in
front of the
temperature display~.&.
19

Downloaded from www.Manualslib.com manuals search engine Driver information system
Multifunction steering
wheel plus
Operating
Apples to: vehicles with multifunction steering wheel plus
The Multifunction steering wheel plus* hos 14
buttons. You con use them to operate the driver
information
system and the MMI functions,
change the volume and switch the voice recogni­
tion system* on and off.
Fig. 7 Infotainment system display
Fig. 8 Multifunction
steering wheel operation
Requ irement: the ignition must be switched on.
The driver information
system contains multiple
tabs CD that display various information @.
The
following tabs are available, depend ing on
vehicle
equipment:
1. Tab Vehicle
2 . Ta
ba)
Warnings
3. Tab
Rad io¢ page 145
Media~ page 149
4. Tab Telephone* ¢page 110
20
5. Tab Navigation*¢ page 131
Map*
6. Tabb >
Sound ¢page 166
Audi connect* ¢page 121
Settings ¢page 166
a) This tab is only visible if at least o ne indicator light or
message is shown or if the correspon ding system is
sw i
tched on.
bl The contents of the tab depen d on the men u that was
used last.
® button I <11> I
- Switching tabs: press the I I button to the
left/right (for example, radio).
@IVIEWI button
-Switching views: press the IVIEWI button to
switch from the classic¢ page 19, fig. 5 to the
expanded ¢ page 19, fig. 6 view.
® buttonl2J
-Returning to functions at higher levels: press
the~ button.
@ 12] and 0 control buttons
-Opening the selection menu: press the left
control button.
-Opening the options menu: press the right
control button.
Q) Left thumbwheel
-Selecting a function in a menu/list: turn the
left thumbwheel to the desired function in a
menu or list (such as selecting a station, Lap
times*) .
-
Confirming a selection: press the left thumb­
wheel (for example, confirm the station).
-Zooming in/out on the map: when a map is
displayed, turn the left thumbwheel up/down
to zoom in/out on the map.

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
..... I.Cl U"I
..... I.Cl .....
Opening and closing
Central locking
Description
You can lock and unlock the veh icle centrally. You
have the following options:
-Remote control key<=> page 2 7,
-
Sensors in the door handles*<=> page 28,
- Lock cylinder on the driver's door<=> page 30,
or
-Central locking switch inside<=> page 29.
Auto Lock
The Auto Lock function locks all doors and the
luggage compartment lid once the speed has ex­
ceeded approximately 9 mph (lS km/h).
The vehicle can be unlocked if the opening func­
tion in the central locking system switch is used
or one of the door handles is pulled. The Auto
Lock function can be switched on and off in the
Infotainment system<=> page 29.
Additionally, in the event of a crash with airbag
deployment the doors are automatically un­
locked to allow access to the vehicle.
Selective unlocking
The doors and luggage compartment lid will lock
when they close. You can set in the Infotainment
system whether only the driver's door or the en­
tire vehicle should be unlocked when unlock ing
<=>page29.
Turn signals
When you unlock the vehicle, the turn signals
f l
ash twice. When you lock the vehicle, the turn
signals flash once. If the blinking continues, one
of the doors or the luggage compartment lid is
not closed or the ignition is sti ll switched on.
Unintentionally locking yourself out
In the following cases there safeguards to pre­
vent you locking your remote master key in the
vehicle:
-
If the driver's door is open, the veh icle cannot
be locked by pressing the !ml button on the re-
Opening and closing
mote control key or touching the locking sen­
sor* on a door.
-When locking using the Im] button in the central
locking switch, the vehicle will not lock if a door
is open <=>page 29.
-On veh icles with a convenience key*, the lug­
gage compartment lid unlocks again after clos­
ing if
the most recently used key is in the lug­
gage compartment. The emergency flashers
blink four times.
Do not lock your vehicle with the remote control
key or convenience key* until all doors and the
luggage compartment lid are closed. In this way
you avoid locking
yourself out accidentally.
@Tips
-Do not leave valuables unattended in the ve­
hicle. A locked vehicle is not a safe!
-The LED in the driver's door rail blinks when
you lock the vehicle. If the LED lights up for
approximately 30 seconds after locking,
there is a malfunction in the central locking
system. Have the problem corrected by an
authorized Audi dealer or authorized Audi
Service Facility.
Key set
Fig. 14 Your vehicle key set
@ Remote control key with integrated
mechanical key
You can unlock/lock your vehicle with the remote
control key . A mechanical key is integrated in the
remote control key ¢ page 26.
@ Key fob with PIN
Only applies to vehicles with Connectivity serv-
ice* :
open the key fob and rub the PIN until it is ..,.
25

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
LED and batteries in the remote control key
Fig. 16 Rem ote contro l key: rem ov ing the battery hol der
Fig. 17 Remote control key (back side ): remov ing the ba t­
tery ho lder
LED in the remote control key
The LE D @ info rms you of the remote control key
function.
•If you press a button quick ly, the LED blinks
once .
• If you press a button longer (convenience open­
ing/ closing), the LED blinks several times.
•If the LED does not blink, the remote control
key battery is dead . The Ill indicator light and
the message Remote control key: change key
battery appear. Replace the battery.
Replacing the remote control key battery
• Press the release buttons@ ¢ fig. 16 and re­
move the mechanical key.
.. Press the release buttons© ¢ fig. 17 on the
battery holder and, at the same time, pull the
battery holder out of the remote contro l key in
the direction of the arrow .
.. Insert the new battery with the"+ " facing
down .
.. Push the battery holder carefully into the mas­
ter key.
~ •Install the mechanical key . .....
Opening and closing
@) For the sake of the environment
Dead batteries must be disposed of using
methods that will not harm the environment.
Do not dispose of them in household trash.
@Tips
The replacement battery must meet the same
specificat ions as th e origina l battery.
Unlocking/locking by remote control
Fig. 18 Remote contro l key : button programming
.. To unlock the vehicle , press the Im button
¢ fig. 18.
.. To lock the vehicle, press the~ button once.
.. To open the luggage compartment lid, press
the~ button .
.. To trigger the alarm, press the red I PANIC I but­
ton. The vehicle horn and emergency flashers
turn on.
•To switch off the alarm, press the red I PANIC I
button again .
If the vehicle is unlocked and none of the doors,
the rear lid or hood are opened within 45 sec­
onds,
the veh icle locks again automatically. This
f
eature prevents the vehicle from being acciden­
tally
left un locked over a long period of time.
T
he setti ngs in the Infota inment system deter­
mine if the entire vehicle or only the driver's door
is un locked when un locking the vehicle
¢page 29.
A WARNING
--1
No one, especially children, should stay in the
vehicle when it is locked from the outside, be­
cause the windows are no longer able to open
27

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
Central locking switch
Fig. 20 Driver's door: central loc king switch
... To lock the veh icle, press the@! button ¢,&. .
... Press the !ill button to unlock the veh icle .
When locking
the vehicle with the central locking
switch, the
following applies :
- Opening
the door and the lu ggage compart­
ment lid from the outside is not possible (f or
sec urity such as when stopped
at a light) .
- The
LED in the central locking switch turns on
when all doors are closed and locked.
-
You can open the doors individually from the
inside
by pulling the door handle .
- In the event of a crash with airbag deployment,
the doors unlock automatically to allow access
to the vehicle .
.&. WARNING
-The power locking switch works with the ig­
nition off and automatically locks the entire
vehicle when
the~ button is pressed .
- The centra l loc kin g switc h is inoperative
when
the veh icle is l ocked from the outside.
-
Locked doors make it more difficult for
eme rgency workers
to get into the veh icle,
whic h puts lives at risk. Do not leav e anyone
behi nd i n
the ve hicle , especially children.
@ Tips
Your vehicle locks a u
tomatically when it
reaches a speed of 9 mph (15 km/h) (Auto
Lock) q page 25. You can unlock the vehicle
ag
ain usi ng the [ill button in the ce ntral loc k­
ing switch.
.....
"' l) This functio n is not availa ble in all countries . .....
Opening and closing
Setting the central locking system
In the Infotainment system, you can set which
doors the central locking system will unlock .
... Select in the Infotainment system: I MENU! but­
ton> Vehicle> left control button >Vehicle set­
tings .
Door unlocking
-you can decide if All doors or
only
the Driver door should unlock. The luggage
compartment
lid also unl ocks when All is select ­
ed. If you select Driver i n a vehicle with a conve n­
ience key*, only the doo r whose handle you pull
will un
lock .
If you select Driver , all the doors and luggage
compartment
lid will unlock if you press the@l
button on the remote control key twice.
Fold mirrors * -if you select On, the exterior rear­
view mirrors fold in automatically when you press
the l:ru button on the remo te contro l master key
or touch th e s ensor* in th e handle .
Lock when driving l) -if you select On, the vehi­
cle locks automatically when driving. All of the
doo rs and the luggage compartment lid lock.
29

Downloaded from www.Manualslib.com manuals search engine ..... N
G: CX)
.....
"' U"I
.....
"' .....
-For security reasons, the windows can only
be
opened and closed with the remote con­
trol key at a maximum distance of approxi­
mately 6 ft (2 m) away from the vehicle.
When pressing the[@ button, always watch
the windows while they are closing so that
no one is pinched in the window. The closing
process will
stop immediately when the~
button is released.
Correcting power window malfunctions
After disconnecting the vehicle battery, the one­
touch up
and down feature must be activated
again.
~ Pull the power window switch until the window
is completely ra ised.
~Release the switch and pull it again for at least
one second.
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink}
Fig.
27 Garage door opener: examp les of usage for diffe r­
ent system s
W ith the garage door opener (Homelink), you
can activate
systems such as the garage doors,
security
systems or house lights from inside your
vehicle. Up to three remote control functions can
be
programmed to the three buttons that are in­
tegrated in the control unit above the rearview
mirror .
T o
be able to operate systems using the garage
door opener, the buttons in the control unit must
first be programmed .
Opening and closing
A WARNING
f=
When operating or programming the garage
door opener, make sure that no people or ob­
jects are in the area immediately surrounding
the system. People can be inju red o r property
can be damaged if struck when closing.
@ Tips
-For security reasons, we recommend that
you clear the programmed buttons before
selling the vehicle.
- For
further information regarding Home­
Link,
refer to www.homelink.com .
-For the Declaration of Conformity with the
prov is ions from the FCC in the United States
and Industry Canada, refer to~ page 297.
Operation
Applies to: vehicles with garage door opener (Home link)
Fig .
28 Contro l panel above the interio r rearv iew mirro r
Requirement: the button in the control panel
must be programmed~ page 34 and the vehi­
cle
must be located within range of the system,
suc h
as the garage door.
~ Press the button to open the garage door. The
green LED@ blinks or turns on.
~ Press the button again to close the garage
door.
(j) Tips
To open or close the garage door, do not
press the button longer than 20 seconds or
the garage door opener will switch to pro­
gramming mode.
33