lock AUDI TT ROADSTER 2018 Workshop Manual

Child sa fety
A WARNING
Always take specia l precautions if you must
install a forward or rearward-facing chi ld re­
straint on the front passenger's seat in excep­
tional situations:
- Whenever a forward or rearward-facing
child restraint is installed on the front pas­
senger seat, the
P ASS ENGER AIR B AG OFF
'-i; light must come on and stay on whenev­
er the ignition is sw itched on .
- If the
PASS ENGER AIR B AG O FF ~; light
does not come on and stay on, perform the
checks descr ibed
<=> page 205, Monitoring
the Advanced Airbag System.
- If the PA SSENGER AIR BAG OFF ~; light
does not come on and stay on whenever the
ignition is switched on the inflating airbag
will hit the child safety seat o r infant ca rr ier
with great force and will smash the child safety seat and child against the backrest,
center armrest, door or roof . Have the air­
bag system inspected immediately by your
Audi dealer.
- Improper installation of chi ld restraints can
red uce their effect iveness or even prevent
them from providing any protection.
- An improperly installed chi ld restraint can
interfere with the airbag as it deploys and
seriously injure or even kill the child.
- Always carefully follow the manufacturer's
instructions provided w ith the ch ild safety
seat or carrier.
- After checking to make sure that the child
restra int is properly installed, make certain
that the child restraint is correctly recog­
nized by the capac it ive passenger detection
system in the front passenger seat and that
the
PASSENGER AIR BAG OFF '-i; light sig­
nals the co rrect front passenge r frontal air­
bag status.
A WARNING
Forward-fac ing ch ild rest raints:
- Always make sure the forward-facing seat
has been designed and cert ified by its man­
ufact urer for use on a front seat with a pas­
senger front and side airbag .
226
--
Never put the forward-facing child restraint
up, against or very near the instrument pan­
el.
- Always move the passenger seat into its
rearmost posit ion in the seat's fore and aft
adjustment range, as far away from the a ir­
bag as poss ible before installing the for­
ward-facing chi ld restraint. The backrest
must be adjusted to an upr ight position.
- Make sure that the
PASSENGER AIR BAG
OFF
'-i; light comes on and stays on all the
time wheneve r the ign it ion is switched on.
A WARNING
Rearward-facing chi ld restraints:
- A child in a rearward-fac ing ch ild safety seat
installed on the front passenger seat will be
serious ly injured and can be killed if the
front airbag inflates
-even with an Ad­
vanced Airbag System.
- The inflating airbag will h it the ch ild safety
seat o r infant c arr ier with great force and
w ill smash the child safety seat and child
against the backrest, center armrest, door
or roof.
- Always be especially carefu l if you must in­
stall a rearward facing child safety seat on
the front passenger seat in exceptiona l cir­
cumstances.
- Make sure that the
PASSENGER AIR BAG
OFF
'-i; light comes on and stays on all the
time whenever the ign it ion is switched on.
- If the
PASSENGER AIR BAG OFF '-i; light
does not come on and stay on, have the air­ bag system inspected by your Audi dealer.
Activating the convertible locking retractor
Use the convertible locking retractor to secure a
child restraint.
A lways heed the c hil d safety seat manufacturer's
instructions when insta lling a child restraint in
your vehicle. To activate the convertib le locking
retractor:
.,. Place the chi ld restraint on a seat .
.,. Slowly pull the belt all the way out .

Cl 00 .-< N r-­N .-< 0 r-­Vl 00
~ Route it around or through the child restraint
belt path
¢ ,& .
~ Push the child safety seat down with your fu ll
weight to get the safety be lt really t ight.
~ Insert the belt tongue into the buckle for that
seat ing pos ition .
~ Guide the safety belt back into the retractor un­
t il the belt lies flat and snug on the ch ild safety
seat.
~ Yo u should hear a "clicking" no ise as the belt
winds back into the inertia reel. Test the con ­
vertib le locking retractor by pu lling on the belt .
Yo u should no longer be ab le to p ull the belt
o ut of the retractor. The convertible locking re­
tractor is now activated .
~ Make sure that the red release button is fac ing
away from the child restraint so that it can be
unbuckled qu ickly .
~Pullon the be lt to make sure the safety belt is
prope rly tig ht and fastened so that the seat
canno t move forward and s idew ays more th an
1 in (2 .5 cm).
A WARNING
Using t he wrong child restraint or an improp ­
erly installed c hild restraint can cause ser ious
personal inju ry or death in a cras h.
- Always make sure that the safety belt re -
tractor is locked when install ing a child
safety seat. An unlocked safety belt retrac­
tor cannot hold the child sa fety seat in place
dur ing normal dr iving or in a crash.
- Always buckle the child safety seat firmly in
place even if a child is not sitting in it. A
loose child safety seat can fly around duri ng
a sudden stop or in a crash.
- Always make sure the seat backrest to which
the ch ild restraint is installed is in an up­
r ight position. Ot he rw ise, the seatback w ith
the ch ild safety sea t atta ched to i t could fly
f orward in the even t of an ac cident o r othe r
eme rgency si tuation .
- Alw ays read and heed all WAR NINGS w hen ­
ever using a child restra ined in a veh icle is
being used
¢ page 216. Specia l preca utions
app ly when installing a child safety seat on
the front passenger seat
9 page 195, Child
Ch ild saf ety
restraints on the front seat -some impor ­
tant things to know.
Deactivating the convertible locking
retractor
The convertible locking retractor for child re­
straints will be deactivated automatically when
the belt is wound all the way back into the re ­
tractor .
~ Press the red button on the safety belt buckle.
The belt tongue will pop out of the buck le.
~ Guide the safety belt all the way back into its
stowed posit ion .
Always let the safety belt retract completely into its stowed posit ion . The safety be lt can now be
u sed as an ord inary safety belt w ithout the con­
vertib le locking ret racto r fo r ch ild rest raints .
If the convertible locking retractor should be ac­
t ivated inadvertently, the safety belt must be un­
fastened and guided completely back into its
stowed pos ition to deactivate th is feature .
If the
conve rtible locking retractor is not deactivated,
t h e safety be lt will g radu ally become tigh ter and
u ncomfortab le to wear.
A WARNING ,..__ -
I mproper ly installed child safety seats in­
crease the risk of se rious persona l injury and
death in a co llision.
- Never unfasten the safety belt to deactivate
the co nvertib le locking ret racto r fo r ch ild re­
stra ints w hile the vehicle is mov ing. You
wou ld not be restrained and could be seri­
ously injured in an accident .
- Always read and heed all WARNINGS when­
ever us ing a chi ld restrained in a vehicle is
be ing used
¢ page 216. Special p recautions
apply when install ing a child safety seat on
the fro nt passenge r
seat¢ page 195, Child
restrain ts on the front seat
-some impor­
tan t things to know.
227

Checking and Filling
-If you a re unable to determine whether or
not a particular fuel blend meets the speci­
fications, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can­
not be identified.
- Fuel system damage and performance prob­
lems resulting from the use of fuels differ­
ent from those specified a re not the respon­
sibility of Audi and are not covered under
the New Vehicle or the Emission Control System Warranties.
- If you experience a loss of fuel economy or
driveability and performance problems due
to the use of one of these fuel blends , we
recommend that you switch to unblended
fuel.
Gasoline additives
A major concern among many auto manufactur­
ers is carbon deposit build-up caused by the type
of gasoline you use.
Although gasoline grades differ from one manu­
facturer to another, they have certain things in
common. All gasoline grades contain substances
that can cause deposits to collect on vital engin e
parts, such as fuel injectors and intake valves. Al­
though most gasoline brands include additives to keep engine and fuel systems clean, they are not
equally effective .
Audi recommends using TOP TI ER Dete rgent Gas­
oline. For more information on TOP TIER Deter­
gent Gasoline , please go to the official website
(www .toptiergas .com) .
After an extended per iod of us ing inadequate
fuels, carbon deposit build-ups can rob your
en­
gine of peak performance.
(D Note
Damage or malfunction due to poor fuel qual­
ity is not covered by the Audi New Vehicle Limited Warranty.
230
Refueling
Fueling procedure
Your vehicle is equipped with a capless fuel filler
system .
Fig. 172 R ight rea r sid e of the vehicle : ope ning the fuel
fil ler door
Fig. 173 R ig ht rea r sid e of t he ve hicle: fuel pum p nozz le
in ser ted
The fuel filler door is unlocked or locked by the
central locking system.
.. Press on the left side of the fuel filler door to
open
r:::;, fig . 172.
.. Insert the fuel pump nozzle all the way into the
fuel tank filler neck
r:::;, fig. 173. Make sure it is
seated correctly.
.. Begin fueling. Once the fuel pump no zzle turns
off the first time, the fuel tank is full. Do not
continue fueling, or else the expansion space in
the tank will be filled with fuel.
.. After the fuel pump has switched off, wait five
seconds before removing it to allow the rest of
the fuel to finish dripping into the fuel tank.
.. Close the fuel filler door and then press on the
left side until it latches.
The correct fuel type for your vehicle can be
found on a label located on the inside of the f uel
ll>

Cl 00 .-< N r-­N .-< 0 r-­Vl 00
filler door . For additional info rmation on fuel,
see
~ page 229.
F or the tank capac ity in yo ur vehicle , refer to t he
Technical Data
~ page 288 .
To reduce the r isk of fuel leak ing out or vapors
escap ing, make su re t hat the fuel ta nk is closed
correct ly. O therwise
t he-¢..ij indicator light will
turn on.
I f the central lock ing system malfunct ions, the
fuel filler door may emergency release
~ page 232.
_& WARNING
An improper f uel ing p rocedure and improper
hand ling of fue l can lead to exp losions, fires,
severe b urns and other injuries .
- Do not smoke and keep away from open
flames .
- T he ig nition m ust be switched off whe n re ­
f ueling .
- Cell pho nes, radio devices and o ther radio
equipment s hou ld always be switched off
w hen refueling . Electromagnetic rays cou ld
cause sparks and start a fire .
- If you do not insert the fuel pump nozzle a ll
the way into the filler tube, then fue l can
leak out. Spilled fue l can ignite and start a
fire.
- Never get into the vehicle when refueling. If
there is an exceptional s ituation where the
vehicle must be entered, close the door and
touch a metal surface before touching the
fuel pump nozzle aga in . This will reduce the
r isk of electrostat ic d ischarge that can cause
flying sparks . Sparks can start a fire when
ref uel ing .
_& WARNING
We recommend that you do not t ransport any
fue l co nta iners in t he veh icle. Fue l cou ld leak
out of the containe r and ignite, espe cially dur ­
ing an accident. This can cause exp losions,
fires and injuries .
- If you must transport fuel in a fue l contain ­
er, please note the following:
Ch eck ing and F illing
- Always place a fue l container on the
ground before filling . Never fill the fue l
container with fuel while it is in or on the
vehicle . Electrostatic charge can occur
wh ile refueling and the fuel vapors could
i gnite .
- For fuel containers made of metal, the fuel p ump nozzle must always maintai n
contact with the conta iner to reduce the
r isk of s tat ic charge.
- Insert the fuel pump nozz le as far as pos­
s ible into the fi lle r opening w hile refuel­
ing .
-Fo llow lega l requ irements when using,
stor ing and t ransporti ng f uel conta iners.
- Make su re that the fuel containe r meets
t h e in dust ry standa rds, for example ANS I
o r ASTM F8S2 -86.
@ Note
- Remove fuel that has overflowed onto any
veh icle components immediately to reduce
the risk of damage to the vehicle.
- Never drive unt il the fuel
tank is completely
empty. The irregula r supply of fue l that re­
sults from that can cause eng ine misfi res.
U nc ombus ted fuel will ente r th e exhaus t
system and increase the risk of damage to
the cata lytic converter.
@ For the sake of the environment
Do not overfill the fuel tank, otherwise f uel
ca n leak o ut w hen the ve hicle is warming up.
(D Tips
- If adverse weat her co nd it io ns cause the f uel
filler door to freeze shut, p ress o n the cen ­
t er of the fi ller door wit h the hee l of your
hand and then try opening it again .
- Th e fuel fi ller door on yo ur vehicle does no t
lock if yo u lock the vehicle from the inside
using the central locking switch.
(D Tips
- Yo ur vehicle is eq uipped w ith a misfue ling
guard. It a llows the vehicle to be f ueled on -
ly with the correct fue l pump nozz le .
.,.
2 3 1

Checking and Filling
- A worn or damaged nozzle or a nozz le that
is too sma ll may not be ab le to open the
diesel misfueling guard. If this is the case,
try turning the nozzle before inserting it in
the fuel filler neck, use a different fuel
p ump, or see an authorized Audi dealer or
authorized Aud i Serv ice Facility for ass is­
tance.
- The misfueling guard does not open when
adding fue l from a fuel conta iner. When re­
fueling with a reserve can ister, you must
u se the funne l stored in the luggage
com­
partment¢ page 232, fig.174.
Fueling with reserve canister (emergency
fueling)
F ig. 1 74 Luggage compartment: funnel
Fig. 17 5 Fue l tank filler neck w it h th e mo unted funnel
Read and fo llow the important safety precau­
tions ¢
A in Fueling procedure on page 231.
.,. Press on the left side of the fuel fille r door to
open
¢ page 230, fig . 172.
.,. Remove the cargo floor ¢ page 272 .
.,. Remove the plastic floor panel ¢ page 50,
fig . 59 .
.,. Remove the funnel from the luggage compart­
ment .
232
.,. Insert t he funnel into the fuel fi ller neck all the
way until it
stops ¢ fig. 175. Make sure that the
r ing on the funne l goes into the fuel tank filler
neck.
.,. Guide the reserve canister fille r tube into the
funnel and start the emergency fueling .
.,. Remove and clean the funne l after the fueling
process . Then close the fue l filler door and
press on it until it latches ..
@ Note
Remove fuel that has overflowed onto any ve­
h icl e compone nts immediately to red uce the
r isk of damage to the vehicle.
Fuel filler door emergency release
If the fuel filler door lock is faulty, the fuel filler
door can be unlocked manually.
Fi g. 176 Luggage comp artme nt: cover in the rig ht s ide
t rim pane l
.,. Open the luggage compartment lid .
.,. Lift the cargo floor .
.,. Loosen the loop from the retainer and then pull
on the loop
carefully ¢ fig. 176 ¢(D . The filler
door is released.
@ Note
Only pull on the loop until you feel resistance.
You w ill not hear it re lease. Otherwise you
could damage the emergency release mecha­ nism .

Checking and Filling
Coolant Freeze protec-
tion
additi ve
Warm min. 40% min. -13 °F
regions (- 25 °C)
max . 45%
Cold min. 50% max. -40 °F
regions (-40 °C)
max. 55%
@ Note
- Before the start of winter, have an author­ ized Audi dealer or authorized Audi Service
Facility check if the coolant additive in your
vehicle matches the percentage appropriate
for the climate. Th is is especially important
when driving in co lder climates.
- If the appropriate coolant additive is not
available in an emergency, do not add any
other additive . You cou ld damage the en­
gine.
If t his happens, only use wate r and re­
store the correct mixture ratio with the
specified coolant additive as soon as possi­
ble .
- Only refill with new coo lant.
- Radiato r sealant must not be mixed w ith
the coo lant .
Adding coolant
Fig . 183 Eng ine co mpartment : coo lant expans ion ta nk
cove r (exa mple)
Observe the safety precautions c:::> page 233 ,
Working in the engine compar tment.
Che cking the engin e coolant l evel
.. Park the vehicle on a level surface .
.. Switch the ignition off .
240
~ 0 > 00 ID
.. Read the coolant level on the coolant expansion
tank
c:::> page 236, fig. 180 . The coolant level
must be between the markings when the en­
gine in cold. When the engine is warm it can be
slightly above the upper mark ing .
Adding coo lant
Requirement : there must be a residual amount of
coolant in the expansion tank
c:::> @ .
.. Let the engine cool down.
.. Place a clot h over the coolant expansion tank
cap and unscrew the cap counterclockwise
c:::> ,A .
.. Add coo lant mixed in the correct rat io
c:::> page 239 up to the upper marking .
.. Make sure that the fluid level remains stable.
Add more coolant if necessary .
.. Close the cap securely .
Coolant loss usually ind icates there is a leak. Im­
mediate ly dr ive your vehicle to a n author ized
Audi dealer or author ized Audi Service Fac il ity
and have the cooling system inspected. If the
cooling system is not lea king , a loss can come
from the coolant boiling through overheat ing
and being pushed ou t of the cooling system .
Lil WARNING
- The cooling system is under pressure. Do
not open the coo lant expansion tank cap
when the engine is hot. This increases the risk of burns.
-The coolant additive and the coolant can be dangerous to your health. For this reason ,
keep the coolant in the original container
and away from children. There is a risk of
poisoning.
-When working in the engine compartment,
remember that the radiator fan can switch
on even if the ignition is switched
off, wh ich
increases the r is k of injury.
@ Note
Do not add coolant if the expans ion tank is
empty . A ir could enter the cooling system and
-
damage the eng ine . If this is the case, do not ..,.

Care and cleaning Component Situation Solution
Power top
Deposits Clean water, power top cleaning product, if necessary.
Clean with the grain of the fabric using a soft brush and al- low to air dry.
Wind deflector Deposits Water, mild
soap solution, if necessaryal
Decorative parts/ Deposits Mild soap solution al, a cleaning solution suitable for stain-
Trim less steel, if necessary
Paint Paint damage Refer
to the paint number on the vehicle data label, repair
with touch up paint¢
page 288
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult
ani authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have it removed by an authorized Audi dealer or authorized
Audi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/pa int looks
poor
Deposits such as in- Dampen with water immediately and remove with a micro-
sects, bird droppings,
fiber cloth
tree sap and road
salt
Grease-based con- Remove immedia tely with a mild soap solution
a) and a
taminants such as soft cloth
cosmetics or sun-
block
Carbon parts Deposits clean the same way as painted parts ¢page 266
Decorative decals Deposits Soft sponge with a mild soap so lutional
al M ild soap so lution: maxim um two tablespoons of neutra l soap in 1 quart (1 lite r) of water
Interior cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap solutional
Trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap solution
al, detergent-free plastic clean-
ing so lution, if necessary
268

Emergency assistance
Emergency assistance
Trunk escape latch
In case of an emergency , the rear lid can be
opened from the inside using the trunk escape
latch.
Fig. 191 L uggage compartment: Trunk escape latch
• Pu sh the latch in the direction of the arrow un­
til the lock releases .
The trunk escape latch inside the rear lid is made
of fluorescent material to g low in the dark.
.&_ WARNING
The trunk escape latch is to be used only in an
emergency.
General information
• Park the vehicle as far as poss ible from moving
traffic in the event of a breakdown . In the event
of a flat tire , park the vehicle on a level surface .
It you are on a steep hill, be especially careful.
• Set the parking brake.
• Place the selector lever in the P position.
• Switch the emergency flashers on.
• Have the passengers exit the vehicle. They
should move to a safe place, for example be ­
hind a guard rail.
.&_ WARNING
Follow the steps given above . This is for your
protection and the for the safety of other driv­
ers.
272
Equipment
Vehicle tool kit/tire mobility kit/
compressor
A UD i 1
Fig. 192 Lu ggage compartmen t: cargo floor closed
The vehicle tool kit, tire mobility kit and com·
pressor are stored in the luggage compartment
u nder the cargo floor cover.
• Push on the plastic handle and lift up the cargo
floor .
• Open the cargo floor.
Completely retract the vehicle jack arm before
storing the vehicle jack* .
.&_ WARNING
Improper use of the veh icle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
attain the necessary tightening torque if you
use the hex head, potentially causing an ac­
cident.
- The factory-supplied jack is intended only
for your vehicle mode l. Under no circum­
stances should it be used to lift heavy
vehicles or other loads; you risk injuring
yourself.
- Never start the engine when the vehicle is
raised, which cou ld cause an accident .
- Support the vehicle securely with appropri ­
ate stands if work is to be performed under­
neath the vehicle; otherwise, there is a
po­
tential risk for injury.
- Never use the jack supplied with your Aud i
on another vehicle, particularly on a heavier
one. The jack is only suitable for use on the
vehicle it came with .
...

Cl co .... N ,..._
N ...... 0 ,..._
Vl co
-If the tire is too severely damaged , see an
authorized Aud i dealer or authorized Aud i
Service Facility for assistance .
@ For the sake of the environment
You can give the used tire sealant bottle to an
author ized Audi dealer or authorized A udi
Service Facility for disposal.
@ Tips
Remember to obtain a new bottle of sea lant
from an authorized Audi dea ler or authorized
Audi Service Facility after repairing a tire.
Replacing wheels
Preparation
You must complete the preparation before
changing a tire .
"' Read and follow the important safety precau-
t ions
Q page 2 72, General information .
"' Set the parking brake .
"'Se lect the "P" selec to r l ever position.
"'Lay out the vehicle tool kit Q page 2 72 and the
spare tire
Q page 279 .
A WARNING ,-
You or your passenger could be injured while
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wait in a safe place away f rom the vehicle and well away
from the road and traffic .
- To help prevent the vehicle from moving suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the front and back of the wheel diagonally
opposite the w heel be ing changed. Whe n
one front whee l is lifted off the ground,
pla cing the A utoma tic Transm ission in P
(Park) will
not prevent the ve hicle from
moving .
Emergen cy as sis tanc e
-Before you change a wheel, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack.
- Always store the vehicle too l kit, the jack
and the replaced tire in the luggage com­
partment
<=) page 183.
(D Tips
Obey all laws .
Removing the cover
Fig. 196 W heel: wh eel hu b cov er
F ig. 1 97 Wheel: wh eel bol ts with cap s
Wheel hub covers*
"'Insert the hook (from the vehicle tool kit) into
the hole on the whee l hub cover
Q fig. 196 .
"'Remove the wheel h ub cover .
Wheel bolts with caps *
"'Slide the p lastic clip (from the veh icle too l kit)
onto the cap unt il it engages
Q fig . 197.
"' Remove the cap with the p lastic clip.
275

Cl co .... N ,....
N ...... 0 ,....
Vl co
-Always stor e damaged whee l, jack and too ls
securely in the luggage compartment. Oth­ erwise, in an accident or sudden maneuver
they could fly forward, caus ing injury to pas­
sengers in the vehicle .
Spare tire
General information
Applies to: veh icles wit h space -saving spa re t ire (compact
spa re t ire)
A U DI
Fig. 203 Lugg age co mpar tment : spar e tir e
F ig . 204 Sp are t ire (ex ample)
The spare tire is intended for short-term use on­
ly . Have the damaged t ire checked and replaced if
necessary by an author ized Audi dealer or author­
i zed A udi Service Fac ility as soon as possib le.
T here are some restrictions on the use of the
compact spare tire . The compact spare tire has
been designed specifica lly for your type of veh i­
cle . Do not replace it w ith the spare tire from an­
o ther type of vehicle.
Removing the spare tire
.,. Turn the handle c::> fig . 203 (D counter-clock­
wise.
.,. Remove the spare tire .
Emergen cy as sis tanc e
Removing the vehicle jack
.,. Lift up the cover on the right side of the lug­
gage compartment and remove the vehicle
jack.
Snow chains
For technical reasons, the use of snow chains on
the compact spare tire is not pe rmit ted.
If you have to dr ive with snow chains and a front
t ire fails , mount the spare tire in place of a rear
t ir e. Install the snow chains on the rear t ire that
yo u removed, and ins tall that in place of the
front t ire that fai led.
_&, WARNING ..
- After insta lling a spare tire, the tire pres ­
sure must be checked as soon as possible .
- D o not dr ive faster than 50 mph (80 km/h)
with a compact spare tire. Driving faster
than that inc reases the risk of an accident.
- To reduce the r isk of an accident, avoid full ­
throttle acceleration, heavy braking, and
fast corner ing with the compact spare tire .
-
- To reduce the risk of an accident, neve r drive
with more than one compact spare tire .
- Normal summer or winter tires must not be mounted on the compact spare wheel rim.
279