intake BMW 540i 2000 E39 Workshop Manual

Downloaded from www.Manualslib.com manuals search engine
... -.
Camshaft Timing chain1
Timing chains, removing
(M52 TU and M54 engines)
Camshaft timing chain removal requires that the oil pan be re-
moved. See
119 Lubrication System. Also required is re-
moval of the VANOS control
unit and disassembly of the
intake and exhaust camshaft sprocket assemblies as de-
scribed earlier in this repair group.
Special BMW
service tools are needed for timing chain re-
moval and installation. The special tools assure proper timing
of the valvetrain. Precise
marlts to set the timing on the cam:
shafts are not provided for reassembly. Read the procedures
through before beginning the job.
CA
UTION-
If the camshafts are not properly timed, the pistons can con-
tact the valves.
- D~sconnect negative (-) cable from battery.
CAUTION-
* Disconnecting the battery may erase fault code@) stored in
control module memory. Check for fault codes using spe-
cial
BMW diagnostic equipment.
Prior to disconnecting the battery, read the battery dis-
connection
cautfons given in 001 General Cautions
and
Warninqs.
- Remove VANOS control unit. See VANOS control unit, re-
moving
(M52 TU and M54 engines).
Remove sealing plug from crankcase below starter and se-
cure crankshaft with
BMW special tool ll 2 300.
Drain engine cooling system. See 170 Radiator and Cool-
ing System.
Remove belt driven cooling fan, fan shroud, and thermostat
housing. See
170 Radiator and Cooling System.
Remove drive belts. See
020 Maintenance.
NOTE-
Mark direction of belt rotation if reusing belt.
- Remove water pump pulley fasteners and pulley.
- Drain engine oil and remove oil pan as described in 119
Lubrication System.

Downloaded from www.Manualslib.com manuals search engine
-
Camshaft Timing chain1
< Remove intake camshaft sprocket mounting nuts (arrows)
and remove spring plate (labelled
FRONT).
Remove tom screws from exhaust camshaft sprocket
(arrows).
Lift off exhaust and intake sprockets with secondary chain,
thrust spacer
(A) and splined shaft (B).
CAUTION-
Splined shafts for both intake and exhaust camshafts share
the same part
numbe,: Remove and mark used splined
shafts in order to reinstall in original locations.
4 Remove exhaust camshaft splined sleeve (A) and shaft (8).

Downloaded from www.Manualslib.com manuals search engine
11 7-55
Camshaft Timing Chain
< Set timing chain on exhaust camshaft end
< Working in cylinder head cavity, remove timing chain cover
bolts
(arrows).
< Remove secondary chain lower guide bolts (arrows). Re-
move chain guide.
NOTE-
Bolt on intake camshaft side is long and extends into timing
chain cover.
- Remove crankshaft loclting tool from transmission bellhous-
ing.

Downloaded from www.Manualslib.com manuals search engine
- Camshaft Timing chain]
< Slide splined shaft onto exhaust camshaft, aligning larger
tooth with corresponding gap of splined sleeve (arrows).
Slide splined shaft in further until
3 small or elongated slots
in splined sleeve are centered to
3 threaded holes in
sprocket.
4 Place intake and exhaust sprocltets in BMW special tool 11 6
180. Position spline gap on intalte sprocket (arrow) as shown
and place secondary chain on sprocltets.
< Carefully remove chain and sprockets from tool and slide
onto camshafts. Align gap in
intalte sprocket splines with cor-
responding gap in camshaft splines (arrow).
CAUTION-
Do not alterposltion ofsprocl(ets with respect to chain when
removing from
specfa1 tool 1 1 6 180.
4 Slide splined shaft onto intake camshaft until approx. 1 mm
(0.04 in.) of splines can still be seen.

Downloaded from www.Manualslib.com manuals search engine
1 17-62
Camshaft Timing Chain
4 Install intake camshaft spring plate so that FRONT mark is
visible. Install mounting nuts (arrows) finger tight.
4 Worlting at exhaust side, insert sprocket mounting Torx
screws into threaded lioles (arrows).
Initially tighten screws to approx.
5 Nm (44 in-lb), then back
off one-half turn.
4 Fit thrust spacer (A) on exhaust camshaft.

Downloaded from www.Manualslib.com manuals search engine
Cp-- Camshaft -- Timing Chain
Secure camshaft sprockets and impulse wheels:
Tighten mounting screws
(A) on exhaust camshaft impulse
wheel to approx.
5 Nm (44 in-lb).
Tighten mounting nuts
(6) on exhaust and intake sprocket
assemblies to approx.
5 Nm (44 in-lb).
Torque down mounting screws (A) and nuts
(6) to iinal
specifications.
Tightening torques Sprocket assembly
to camshaft
initial torque
5 Nrn (44 in-lb)
Sprocket assembly to camshaft
M7 Torx screw (A) 20 Nm (I5 it-lb)
M6 mounting nut (8) 10 Nm (89 in-lb)
- Remove flywheel locking tool from transmission bellhousing
so that crankshaft is no longer secured.
- Remove camshaft loclting tools from rear of camshafts.
4 Crank engine over by hand twice in direction of rotation until
cylinder
1 intake and exhaust camshaft lobes (arrows) face
each other.
- Secure crankshaft in TDC position with BMW special tool
11 2 300.
4 Place BMW special tool 11 3 240 over camshaft ends and
measure clearance of tool to cylinder head surface.
NOTE-
* If the exhaust side of the tool is not flush with the head (gap
A), retime the camshafts as described laler in this repair
group.
Due to flexible sprocket design and VANOS control unit tol-
erances and play, the
intake side of special tool 71 3 240
may be up to
I mm (0.04 in) above the suriace of the cyl-
inder head (gap
B). This is normal. Otherwise, retime the
camshafts as described in
VANOS timing, checking and
adjusting (M52 TU and 11154 engines).
- Remove VANOS setup bracket from front of cylinder head
- Install VANOS control unit. See VANOS control unit, in-
stalling
(01152 TU and M54 engines).
- Install intake camshaft oil baffle

Downloaded from www.Manualslib.com manuals search engine
Camshaft Timing chain1
- Disconnect negative cable (-) from battery.
CAUTION-
Prior to disconnecting the battery, read the battery discon-
nection cautions given
in 001 General Cautions and
Warnings.
4 Removing top and side engine covers:
Press down on locking pins (arrows) to release locks. Lifl
intake manifold cover straight up to remove.
Pry out caps from side covers.
Remove fasteners
and covers.
NOTE-
Some early models use
pry out trim caps and fasteners to
hold the top cover in place.
Disconnect electrical harness connectors at ignition coils
(A).
Remove left and right side ignition coil mounting fasteners
and coils.
NOTE-
Make note of location of ground strap (arrow).
Remove spark plugs.
- Remove posltlve (+) terminal cable from left cylrnder head
cover.
- Unbolt left and right side cable ducts from fuel rail
Remove air filter housing and mass air flow sensor:
Disconnect mass air flow sensor and intake air tempera-
ture sensor electrical harnesses
(A and B).
Remove air filter housing mounting fastener (arrow)
Loosen intake hose clamp
(C).
Remove air filter housing with mass air sensor and intake
duct from throttle body assembly.

Downloaded from www.Manualslib.com manuals search engine
Camshaft Timing chain1
< Remove Automatic Stability Control (ASC) throttle body:
Disconnect electrical harness from throttle position sensor.
Disconnect ASC actuator cable (arrow).
Remove
3 mounting fasteners and remove throttle body.
4 Disconnect fuel tank vent valve line and cap off line (arrow).
- Drain engine coolant and remove hoses from thermostat
housing. See
170 Radiator and Cooling System.
- Remove water pump and thermostat housing. See 170 Ra-
diator and Cooling System.
- Remove left side upper timing chain cover retaining bolts and
remove cover.
4 Counter hold right intake camshaft
CAUTION-
Counter hold camshaft with a 27mm open-end wrench while
loosening sprocket bolts. Grind wrench if necessary to pre-
vent damage to head.

Downloaded from www.Manualslib.com manuals search engine
1 17-72
Camshaft Timing Chain
4 Working at right side cylinder head loosen Intake camshaft
sprocket bolts
(arrows).
4 Secure left and right side camshafts in TDC position:
Use BMW special tool set
11 2 440.
- If necessary, turn camshaft so that special tools are
squarely seated on cylinder head.
Working at left cylinder head loosen
intake camshaft
sprocket bolts
(arrows).
CAUTION-
Counter hold camshaft with a 27mm open-end wrench while
loosening sprocket bolts. Grind wrench
if necessary to pre-
vent damage to head.
Remove BMW special tool
11 2 300 from crankshaft locking
tool bore.

Downloaded from www.Manualslib.com manuals search engine
1 Camshaft Timing Chain
4 Secure right side timing chain and guide rails together with a
plastic wire ties
(arrow).
4 Remove lower timing chain cover bolts (arrows) and cover.
- Remove wire ties supporting guide rails.
-
Q Remove sprocket from intake camshafts and remove timing
chain.
If necessary, remove tensioning rail
(A), reversing rail (B),
and guide rail (C) to remove timing chain.