BUICK CENTURY 2004 Get To Know Guide

Instrument Panel . . . . . . . . . . . . . . . . . . . . . . . . . .2
Instrument Panel Cluster . . . . . . . . . . . . . . . . . . .3
Daytime Running Lamps/Automatic
Headlamp Control . . . . . . . . . . . . . . . . . . . . . . . . .4
Delayed Headlamp Illumination . . . . . . . . . . . . . .4
Turn Signal/Multifunction Lever . . . . . . . . . . . . .4
Cruise Control . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Oil Life Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Tire Inflation Monitor . . . . . . . . . . . . . . . . . . . . . . .7
Audio System . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Automatic Power Door Locks . . . . . . . . . . . . . . .9
Delayed Locking (Automatic Power
Door Locks) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9Remote Keyless Entry Signal
(Security Feedback) . . . . . . . . . . . . . . . . . . . . . . .9
Restraint System for Children
(LATCH) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Window Defogging (HVAC) . . . . . . . . . . . . . . . .10
Trunk Lock Release . . . . . . . . . . . . . . . . . . . . . .10
Trunk Storage . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Dual Climate Control System . . . . . . . . . . . . . . .11
Antilock Brakes (ABS) . . . . . . . . . . . . . . . . . . . .11
Roadside Assistance Program . . . . . . . . . . . . .12
My GMLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Congratulations on your purchase of a Buick Century. Please read this information and your
Owner Manual to ensure an outstanding ownership experience. Note that your vehicle may not
include all the features described in this booklet. Place this booklet in your Owner Manual
portfolio for easy reference.

A. Exterior Lamps Control
B. Turn Signal/Multifunction Lever
C. Instrument Panel Cluster
D. Audio Steering Wheel Controls
E. Gear Shift LeverF.Air Outlets
G. Side Window Defogger Outlet
H. Hood Release
I. Tilt Wheel Lever
J. Horn K. Audio System
L. Ashtray
M. Climate Control
N. Glove Box
O. Instrument Panel Fuse Block
Getting to Know Your2004 Century2
Instrument Panel
See Section 3 of your Owner Manual.

Your vehicle’s instrument panel is
equipped with this cluster or one
very similar to it. The instrument
panel cluster includes these key
features:
A. Engine Coolant Temperature
Gauge
B. Speedometer
C. Gear Shift Indicator
D. Trip Odometer
E. Fuel GaugeIMPORTANT:The instrument panel
cluster is designed to let you know
of many important aspects of your
vehicle’s operation. It is important to
read your Owner Manual and
become familiar with the information
that is being relayed to you by the
lights, Gauges and indicators, and
what action can be taken to ensure
safety and to prevent damage
3
See Section 3 of your Owner Manual.
A
B
C
D
D
E
Instrument Panel Cluster

Getting to Know Your2004 Century4
Turn and Lane-Change Signals
The turn signal has the following posi-
tions: two upward (for right) and two
downward (for left). These positions
allow you to signal a turn or lane
change. To signal a lane change, raise
or lower the lever until the arrow starts
to flash. The lever will return by itself
when released.
To signal a turn, move the lever all the
way up or down. A chime will sound if
you leave the turn signal on for more
than 3/4 mile (1.2 km).
Headlamp High/Low Beam Changer
To change your headlamps from low
beams to high beams, or high to low,
pull the multifunction lever all the way
toward you, then release it. When the
Daytime Running Lamps/
Automatic Headlamp Control
Daytime Running Lamps are an addi-
tional safety feature that makes it easier
for others to see your vehicle during the
day. The headlamp system works auto-
matically to help provide the right
amount of lighting at all times of the day
or night. You can still turn your head-
lamps on manually whenever you wish.
See Section 3 of your Owner Manual.
Delayed Headlamp Illumination
If the Automatic Headlamp Control sys-
tem turns on your headlamps, they will
stay on for 90 seconds after you turn off
the ignition. Delayed Headlamp
Illumination provides lighting when exit-
ing your car and the lamps shut off auto-
matically. This feature can be turned off
by following the instructions in your
Owner Manual.
See Section 3 of your Owner Manual.
Turn Signal/Multifunction Lever
The Turn Signal/Multifunction Lever
located on the left side of the steering
column controls these features:
•Turn and Lane-Change Signals
•Headlamp High/Low Beam Changer
•Flash-to-Pass
•Windshield Wipers
•Windshield Washers
•Cruise Control

5
high beams are on, a symbol
located in the instrument panel will
illuminate.
Flash-to-Pass
This feature uses the vehicle’s high
beams to alert the driver in front of you
that you intend to pass. To use it, pull
the turn signal lever toward you slightly,
but not so far that you hear a click. The
high beams will remain on for as long as
you hold the lever toward you.
Windshield Wipers
To operate the windshield wipers, turn
the WIPER band located on the multi-
function lever upward or downward.
To turn off the windshield wipers, turn
the band to OFF.
For low speed wiping, turn the band
away from you to the LO setting. For
high speeds, turn the band to HI.
Five sensitivity settings, located between
the OFF and HI settings, are provided
for a delayed wiping cycle.
Turn the band to the MIST setting for a
single wiping cycle. Hold the band until
the wipers begin, then let it go.
Windshield Washers
The windshield washer paddle is
marked PUSH and is located on top of
the multifunction lever. Push the paddle
to spray washer fluid onto the wind-
shield. The wipers will run for several
sweeps, then stop or return to your pre-
set speed.
See Section 3 of your Owner Manual.
Cruise Control
The Cruise Control feature is located at
the end of the Turn Signal/Multifunction
Lever. Cruise Control allows you to
maintain a speed of about 25 mph or
more (but not below 25 mph) without
keeping your foot on the accelerator. To
use Cruise Control:
1. Move the Cruise Control switch to ON.
2. Achieve the speed you desire.
3. Press the SET button at the tip of the
multifunction lever, then release it.
(The CRUISE light in the instrument
panel cluster will illuminate.)
4. Remove your foot from the
accelerator.
Cruise Control disengages when you
apply the brakes.
Resuming a Set Speed
To return to a preset speed after having
applied the brakes, once you’ve reached
25 mph or more, simply move the
Cruise Control switch from ON to R/A
(Resume/Accelerate).

Getting to Know Your2004 Century6
Oil Life Monitor
The Oil Life Monitor shows an estimate
of the oil’s remaining useful life. When
the oil life index is less than 10 percent,
the CHANGE OIL SOON light will illumi-
nate in the instrument panel. After hav-
ing the oil changed, reset the system so
it can calculate when the next oil change
is required. If you change your oil prior
to the illumination of the CHANGE OIL
SOON light, reset the system.
Resetting the Oil Life Monitor
To reset the Oil Life Monitor, follow
these steps:
1. With the engine off, turn the ignition
key to RUN.
2. Fully push and release the accelera-
tor pedal slowly three times within
five seconds. (If the CHANGE OIL
SOON light flashes, the system is
resetting.)
3. Turn the key to OFF, then start the
vehicle. The oil life will change to 100
percent.
See Section 5 of your Owner Manual.
Increasing Speed While Using Cruise
Control
There are three ways to increase vehicle
speed while using Cruise Control:
1. Use the accelerator pedal to reach
the higher speed. Press the SET but-
ton, then release the button and the
accelerator pedal.
2. Move the Cruise Control switch from
ON to R/A. Hold it there until reaching
the desired speed, then release it.
3. Momentarily push the R/A button. For
every push, vehicle speed will
increase by about 1 mph (1.6 km/h).
Reducing Speed While Using Cruise
Control
To reduce speed while using Cruise
Control, use one of the following
methods:
•Press the SET button until you reach
the lower speed you want, then
release it.
•To reduce speed in smaller incre-
ments, press the SET button briefly.
Each time you press it, you’ll reduce
speed by about 1 mph (1.6 km/h).
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase
speed. After removing your foot from the
pedal, the vehicle will return to the
Cruise Control speed set earlier.
Ending Cruise Control
There are two ways to disengage Cruise
Control:
•Step lightly on the brake pedal.
•Move the cruise switch to off.
See Section 3 of your Owner Manual.

7
Audio System
Controls:
PWR(Power)
VOL(Volume)
DISP(Display): Press this button to
switch the display between the radio sta-
tion frequency and the time.
SCV(Speed-Compensated Volume):
SCV adjusts the audio system volume
automatically to make up for road and
wind noise as you drive. To access the
SCV display, press the TUNE/AUDIO
button repeatedly until SPEED VOL
appears. Then, select from OFF, MIN,
Tire Inflation Monitor System
(if equipped)
ALOW TIRE light will come on if the air
pressure in one tire becomes approxi-
mately 12 psi lower than the car’s nor-
mal tire pressure. After filling a low tire
with air, or after changing or rotating
your tires, the Tire Inflation Monitor must
be reset. The red reset button is located
inside the fuse box, found near the end
of the instrument panel on the passen-
ger side. To reset the monitor, turn the
ignition switch to RUN, then press and
hold the reset button for at least 5
seconds.
See Section 5 of your Owner Manual.
MED or MAX. Each higher choice allows
for more volume compensation at faster
vehicle speeds.
BAND:Press this button to switch
between AM, FM1 and FM2.
TUNE:Turn this knob to choose a radio
station.
:Press the right or left arrow to
go to the next or to the previous station
and stay there. To scan stations, press
and hold one of the SEEK arrows for
two seconds until SCAN appears on the
display. Press one of the SEEK arrows
to stop scanning.
Numbered Buttons
The six numbered pushbuttons let you
return to your favorite preset stations.
(See your Owner Manual for setting your
favorite stations.)
AUDIO:Allows you to adjust the Bass,
Treble, Balance and Fade.
EQ:(Equalizer)
Using the RDS
The Radio Data System (RDS) uses the
FM band to: seek to stations broadcast-
ing the selected type of programming,
receive local or national emergency
announcements, display radio station
messages or seek stations with traffic
announcements. This system only works
when information is available from the
stations.
When using RDS, the station name, call
letters or program type (PTY) informa-
tion will appear in the display instead of
the frequency. The RDS system includes
these controls:
P-TYP(Program type): Press this button
to find and select a desired program
type.

Getting to Know Your2004 Century8
Cassette Player (If equipped)
Use the following controls to operate
your cassette player:
(Reverse):Press this button to
reverse the tape rapidly. Press it again
to return to playing speed.
(Forward):Press this button to
advance quickly to another part of the
tape. Press the button again to return to
playing speed.
SIDE:Press this button to play the
other side of the tape.
:Press the left or right arrow to
go to the previous or next selection on
the tape. (See your Owner Manual for
additional SEEK functions.)
BAND:Press this button to listen to the
radio when a cassette is playing.
CD TAPE:Press this button to play a
tape when listening to the radio.
:Press this button to eject a tape.
See Section 3 of your Owner Manual.
INFO(Information): If the current station
has a message, INFO will appear in the
display. Press this button to view the
message.
TRAF(Traffic): Press this button to seek
to a station that broadcasts traffic
announcements.
Playing a Compact Disc
After inserting a CD into the faceplate
slot, use the following controls to oper-
ate the player:
(Reverse):Press/hold this button to
reverse within a track. Release it to play
the passage.
(Forward):Press/hold this button
to advance within a track. Release it to
play the passage.
4 RDM (Random):Press this button to
play tracks in random order. Press RDM
again to turn off random play.
DISP (Display):Press this button to see
which CD track is playing.
:Press the left arrow to go to
the start of the current track. Press the
right arrow to go to the next track.
Holding or pressing either arrow more
than once will advance you either back-
ward or forward within the track.
BAND:Press to listen to the radio when
a CD is playing
CD:Press when the radio is playing to
listen to a CD.
:Press this button to eject a CD.

9
Automatic Power Door Locks
The Automatic Power Door Locks can
be programmed in the following ways:
Choice 1:All doors will automatically
lock when you shift out of PARK. They
will all automatically unlock when you
shift back into PARK.
Choice 2:All doors will lock automati-
cally when you shift out of PARK. But
only the driver’s door will unlock when
shifting back into PARK.
Choice 3:All doors will automatically
lock when you shift out of PARK. But
you choose no automatic unlocking fea-
ture.
Choice 4:You can also select no auto-
matic door lock or unlock.
See Section 2 of your Owner Manual.
Delayed Locking
(Automatic Power Door Locks)
Your doors will remain unlocked for 3 to
5 seconds after you press the door lock
button, in case you need to get right
back into your car. To lock the doors
immediately, simply press the lock
switch a second time. Refer to your
Owner Manual if you prefer to complete-
ly disable this feature.
See Section 2 of your Owner Manual.
Remote Keyless Entry Signal
(Security Feedback)
Your Remote Keyless Entry system pro-
vides a signal to tell you it’s working.
There are four signals to choose from,
and you can choose a different security
signal for lock and unlock.
Choice 1:Headlamp flash only.
Choice 2:Horn chirp only.
Choice 3:Both a horn chirp and a
headlamp flash.
Choice 4:No signal — no headlamp
flash, no horn chirp.
See Section 2 of your Owner Manual.

Getting to Know Your2004 Century10
Trunk Lock Release
To unlock your trunk, press the button
located behind the glove box door. You
can also unlock the trunk by pressing
the car symbol shown on your Remote
Keyless Entry transmitter. Or, simply use
your door key to open the trunk.
See Section 2 of your Owner Manual.
Window Defogging (HVAC)
Under high humidity and low tempera-
ture conditions, the windows may fog.
To remove this humidity, turn the control
knob to the DEF position. Then, set the
fan to high speed and raise the temper-
ature to the maximum.
See Section 3 of your Owner Manual.
Trunk Storage
Your vehicle’s trunk lid has a four-bar
linkage design which provides more
usable trunk space and will not crush
cargo or intrude into the storage area.
See Section 2 of your Owner Manual.
Restraint System for Children
(LATCH)
Your vehicle’s LATCH system provides
quick and easy installation of child seats
that are equipped with the Lower
Anchorage tether system. The system
uses six anchors on the rear seat with
locations marked on the seatback.
In addition, a top strap anchor is located
behind the rear seat filler panel. In order
to get to the bracket, you must open the
trim cover.
See Section 1 of your Owner Manual.
Trip Odometer
In addition to a mileage odometer, your
vehicle has a trip odometer that informs
you how far you’ve traveled on weekend
trips, back and forth to work, or any-
where else you happen to drive. It is
located in the same place as your
mileage odometer.
To display it, press and release the
black stem located on the right side of
your instrument cluster. To set the trip
odometer to zero, press and hold the
black stem for at least two seconds.
To recall the mileage odometer, press
and release the black stem again.
See Section 3 of your Owner Manual.