ECO mode BUICK RANDEZVOUS 2007 User Guide

4. The program mode message will appear in
the message center as an indication that
your vehicle is ready to begin programming.
5. Follow the instructions given by the DIC.
Headlamp Exit Delay
This feature allows you to customize the
headlamps and parking lamps. This feature can
be programmed to one of the following modes:
OFF:The headlamps and parking lamps will not
turn on at the same instant that the ignition is
turned to OFF.
15:The headlamps and parking lamps will stay
on for 15 seconds when the ignition is turned
to OFF.30:The headlamps and parking lamps will stay
on for 30 seconds when the ignition is turned
to OFF.
60:The headlamps and parking lamps will stay
on for 60 seconds when the ignition is turned
to OFF.
Your vehicle was originally programmed to
30 second mode. The mode may have been
changed since then. To determine the current
mode, or to change the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until HEADLMP EXIT
DELAY appears in the DIC.
3. Press the SET button until the arrow is before
the mode you prefer.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
United StatesCanada
241

Interior Lighting Delay
The interior lighting delay feature can be
programmed to one of the following modes:
OFF:This feature will not illuminate the interior of
your vehicle when all of the doors are closed.
ON:This feature will continue to illuminate
the interior lamps for 25 seconds after all doors
have been closed so that you can nd the ignition
and buckle your safety belt at night.
Interior lighting delay will not occur while the
ignition is in ON. After 25 seconds, the interior
lamps will fade out. The lamps will fade out before
the 25 seconds if one of the following occurs:
The ignition is turned to ON
All doors are locked using the Remote
Keyless Entry (RKE) transmitter
There is no occupant activity detected for an
illumination period of 25 secondsYour vehicle was originally programmed to ON.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until INTERIOR
LIGHTING DELAY appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
242

Interior Lighting On
The interior lighting on feature can be programmed
to one of the following modes:
KEY OUT:The interior lamps will come on for
about 25 seconds whenever you remove the key
from the ignition.
DOOR:The interior lamps will come on for about
25 seconds when any door is opened.
Interior lighting on will not occur while the ignition
is in ON. After 25 seconds, the interior lamps
will fade out. The lamps will fade out before the
25 seconds if one of the following occurs:
The ignition is turned to ON
LOCK is pressed on the Remote Keyless
Entry (RKE) transmitter
There is no occupant activity detected for an
illumination period of 25 secondsYour vehicle was originally programmed to DOOR.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until INTERIOR
LIGHTING ON appears on the DIC.
3. Press the SET button until the arrow is before
KEY OUT or DOOR.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
243

Delayed Locking
The delayed locking feature can be programmed
to one of the following modes:
ON:Lock your vehicle using the power door
lock switch or the Remote Keyless Entry (RKE)
transmitter while any door is opened, you will
hear three chimes and the doors will not lock.
Five seconds after the last door is closed, all doors
will lock.
Once delayed locking is programmed to ON, you
can do the following:
Cancel the delayed locking by pressing unlock
using the power door lock switch or by fully
inserting the key in the ignition
Override the delayed locking feature by
pressing lock immediately using the power
door lock switch
Let the delayed locking feature complete the
locking of the vehicleOFF:The doors will always lock immediately
when you lock the doors using the power door lock
switch or press LOCK on the RKE transmitter.
Your vehicle was originally programmed to
ON. The mode may have been changed since
then. To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until DELAYED
LOCKING appears on the DIC.
3. Press the SET button until the arrow is before
ON or OFF.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
245

Remote Door Unlock
The remote door unlock feature can be
programmed to one of the following modes:
DRIVER/ALL:With the rst press of UNLOCK on
the Remote Keyless Entry (RKE) transmitter,
the driver’s door will unlock, and with the second
press of UNLOCK, within ve seconds of the
rst press, all passenger’s doors will unlock.
ALL:All doors will unlock with every press of
UNLOCK on the RKE transmitter.
Your vehicle was originally programmed to ALL.
The mode may have been changed since then.
To determine the current mode, or to change
the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Press the MODE button until REMOTE DOOR
UNLOCK appears on the DIC.
3. Press the SET button until the arrow is before
DRIVER/ALL or ALL.The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.
Unlock Feedback
The unlock feedback feature can be programmed
to one of the following modes:
LIGHTS:This mode does the following:
During the day, when the ignition is in OFF
and UNLOCK on the Remote Keyless Entry
(RKE) transmitter is pressed, the headlamps
and parking lamps will ash.
During the night, when the ignition is in OFF,
the headlamps and parking lamps will be
activated for 30 seconds when UNLOCK is
pressed on the RKE transmitter. If you would
like to change the amount of time the
lamps stay on, change the headlamp exit
delay feature.
OFF:The headlamps and parking lamps will not
ash when UNLOCK is pressed on the RKE
transmitter.
246

Your vehicle was originally programmed to
LIGHTS. The mode may have been changed
since then. To determine the current mode, or to
change the mode, do the following:
1. Follow the instructions for “Entering
Programming Mode” listed previously.
2. Follow the instructions for programming
HEADLMP EXIT DELAY earlier in this section,
to make sure which mode it is programmed to.
3. Press the MODE button until UNLOCK
FEEDBACK appears on the DIC.
4. Press the SET button until the arrow is before
LIGHTS or OFF.
5. Press the MODE button until you have
determined which mode you prefer, to
follow with the personalization.
The mode you selected is now set. You can either
exit programming mode by following the
instructions later in this section or program the
next feature available on your vehicle.Lock Feedback
The lock feedback feature can be programmed to
one of the following modes:
OFF:When LOCK is pressed on the Remote
Keyless Entry (RKE) transmitter, the headlamps
and parking lamps will not ash and the horn
will not sound.
LIGHTS:When LOCK is pressed on the RKE
transmitter, the headlamps and parking lamps will
ash briey.
LIGHTS and HORN:When LOCK is pressed a
second time on the RKE transmitter within
ve seconds, the headlamps and parking lamps
will ash briey and the horn will sound.
247

SCV (Speed-Compensated Volume):With SCV,
your audio system adjusts automatically to
make up for road and wind noise as you drive.
To get to SCV, push the TUNE/AUDIO knob
repeatedly until SPEED VOL (volume) displays.
Turn the TUNE/AUDIO knob to select MIN
(minimum), MED (medium), or MAX (maximum).
Each higher setting allows for more volume
compensation at faster vehicle speeds. Then, as
you drive, SCV automatically increases the
volume, as necessary, to overcome noise at any
speed. The volume level should always sound
the same to you as you drive. To turn SCV
off, press SCV until OFF displays.
DISP (Display):Press this button to switch the
display between the radio station frequency
and the time. Press this button to display the time
when the ignition is turned off.
For RDS, press the DISP (display) button to
change what appears on the display while using
RDS. The display options are station, RDS station
frequency, PTY (program type), and the name
of the program (if available).For XM™ (if equipped), press the DISP button
while in XM™ mode to retrieve four different
categories of information related to the current
song or channel: Artist, Song Title, Category
or PTY, Channel Number/Channel Name.
To change the default on the display, press the
DISP button until the desired display appears, then
hold the button until the display ashes. The
selected display becomes the default.
Finding a Station
BAND:Press this button to switch between FM1,
FM2, or AM, or XM1 or XM2 (if equipped). The
selection displays.
TUNE:Turn this knob to select radio stations.
©SEEK¨:Press the right or the left arrow to go
to the next or to the previous station and stay there.
To scan stations, press and hold either SEEK arrow
for two seconds until SCAN displays. The radio
goes to a station, plays for a few seconds, then
goes to the next station. Press either SEEK arrow
again to stop scanning.
254

To adjust both tone controls and both speaker
controls to the middle position, rst exit the audio
mode by waiting ve seconds without making
any changes. Then push and hold the AUDIO knob
for more than two seconds until you hear a
beep. ALL CENTERED displays.
EQ (Equalizer):Press this button to select
customized equalization settings designed for
country/western, jazz, talk, pop, rock, and
classical.
Adjusting the Speakers (Balance/Fade)
AUDIO:To adjust the balance between the
right and the left speakers, push and release the
AUDIO knob until BAL (balance) displays.
Then turn the AUDIO knob to move the sound
toward the right or the left speakers. A bar graph
with indicators shows how the sound is balanced.
To adjust the fade between the front and the
rear speakers, push and release the AUDIO knob
until FADE displays. Then turn the AUDIO
knob to move the sound toward the front or the
rear speakers. A bar graph with indicators shows
how the sound is balanced.To adjust balance or fade to the middle position,
select BAL or FADE. Then push and hold the
AUDIO knob for more than two seconds until you
hear a beep. The indicator is centered on the
display.
To adjust both tone controls and both speaker
controls to the middle position, rst exit the audio
mode by waiting ve seconds without making
any changes. Then push and hold the AUDIO knob
for more than two seconds until a beep sounds.
ALL CENTERED displays.Finding a Program Type (PTY) Station
(RDS and XM™)
To select and nd a desired PTY perform the
following:
1. Press P-TYP to activate program type select
mode. The PTY symbol displays.
2. Turn the AUDIO knob to select a PTY.
3. Once the desired PTY displays, press either
SEEK arrow to select the PTY to go to the
PTY’s rst station.
256

4. To go to another station within that PTY while
the PTY is displayed, press either SEEK
arrow once. If the PTY is not displayed, press
either SEEK arrow twice to display the PTY
and then to go to another station.
5. Press P-TYP to exit the program type,
select mode.
If the PTY times out and is no longer displays,
go back to Step 1.
If both PTY and TRAF (traffic) are on, the radio
searches for stations with the selected PTY
and traffic announcements.
SCAN:Scan the stations within a PTY by
performing the following:
1. Press P-TYP to activate program type select
mode. The PTY symbol displays.
2. Turn the AUDIO knob to select a PTY.3. Once the desired PTY is displayed, press and
hold either SEEK arrow. The radio begins
scanning the stations in the PTY.
4. Press either SEEK arrow to stop at a station.
If both PTY and TRAF are on, the radio scans
for stations with the selected PTY and traffic
announcements.
BAND (Alternate Frequency):Alternate
frequency lets the radio switch to a stronger
station with the same program type. To turn
alternate frequency on, press and hold BAND for
two seconds. AF ON displays. The radio can
switch to stations with a stronger frequency.
To turn alternate frequency off, press and hold
BAND again for two seconds. AF OFF displays.
The radio does not switch to other stations.
This function does not apply for XM™ Satellite
Radio Service.
257

RCL (Recall):Press this knob to switch the
display between the radio station frequency and
the time. When the ignition is off, press this
knob to display the time.
For RDS, press the RCL knob to change what
appears on the display while using RDS. The
display options are station name, RDS station
frequency, PTY, and the name of the program
(if available).
For XM™ (if equipped), press the RCL knob while
in XM mode to retrieve four different categories
of information related to the current song or
channel: Artist, Song Title, Category or PTY,
Channel Number/Channel Name.
To change the default on the display, press the
RCL knob until you see the display you want, then
hold the knob until the display ashes. The
selected display becomes the default.
Finding a Station
BAND:Press this button to switch between FM1,
FM2, AM, or XM1 or XM2 (if equipped). The
display shows the selection.
TUNE:Turn this knob to select radio stations.
sSEEKt:Press the right or the left arrow to
go to the next or to the previous station and
stay there.
The radio only seeks stations with a strong signal
that are in the selected band.
sSCANt:Press and hold either SCAN arrow
for two seconds until SC displays and a beep
sounds. The radio goes to a station, plays for a
few seconds, then goes to the next station. Press
either SCAN arrow again to stop scanning.
To scan preset stations, press and hold either
SCAN arrow for more than four seconds. PRESET
SCAN displays and a double beep sounds. The
radio goes to the rst preset station stored on the
pushbuttons, plays for a few seconds, then
goes to the next preset station. Press either SCAN
arrow again to stop scanning presets.
The radio only scans stations with a strong signal
that are in the selected band.
264