BUICK ROADMASTER 1993 Owners Manual

The lever on the left side of the steering column
includes your:
0 Turn Signal and Lane Change Indicator
0 Headlight High-Low Beam & Passing Signal
Windshield Wipers The
turn signal has two upward (for Right) and two
downward (for Left) positions. These positions allow
you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or down.
When the turn is finished, the lever will return
automatically.
0 Windshield Washer
Cruise Control (Option) instrument panel will flash
Turn Signal and Lane Change Indicator , ' in the direction of the turn
.-- A green arrow on the
I .or lane change.
To signal a lane change, just raise
or lower the lever
until the green arrow starts
to flash. Hold it there until
you complete your lane change. The lever will return by
itself when you release it.

As you signal a turn or a lane change, if the arrows don't
flash but just stay on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid an
accident. If the green arrows don't go on at all when you
signal a turn, check the fuse (see "Fuses" in the Index)
and for burned-out bulbs.
If you have a trailer towing option with added wiring for
the .trailer lights, a different
turn signal flasher is used.
With this flasher installed, the signal indicator will flash
even if
a turn signal bulb is burned out. Check the front
and rear turn signal lights regularly to make sure they
are working.
Turn Signal Reminder
A chime will sound if your turn signal remains on after
having driven
1/2 mile, to remind you to turn off your
signal.
Operation of Lights
Although your vehicle's lighting system (headlamps,
parking lamps, fog lamps, side marker lamps and tail
lamps) meet all applicable Federal lighting
requirements, certain States and Provinces may apply their own lighting regulations that may require special
attention before you operate these lamps. For.example,
some jurisdictions may require that you operate your
lower beam lamps with fog lamps at -all times, or that
headlamps. be turned
on whenever you.must use your
windshield wipers. In addition, most jurisdictions
prohibit driving solely with parking lamps, especially at
dawn or dusk. It is recommended that you check with
you own State or Provincial highway authority. for
applicable lighting regulations.
Headlight High-Low Beam
To change the headlights.
l .from low beam to high or..'
:hi:& -to low, pull the turn
signal lever all the way
'toward you. Then .release it.
When the high beams are
on, a blue light, on the
instrument panel -also will
be on.
90

You Control the windshield wipers by tudng the bmd- 1 I
marked “WEER.”
For a single wxping cycle, turn the band to “MIST.”

7 The rear window
washer/wiper' switch i. at
93

Cruise Control (Option) ,* .. :. .> ..
..
";. ?y . ..
I you can't drive safely at a steady speed.
So, don't use your Cruise Control on
winding roads or
in heavy traff'
Cruise Control can be dangerous
slippery roads. On such roads, fast
changes in tire traction can cause
needless wheel spinning, and you
COI
lose control. C tt I ~ = P ise ^ontrol on
I
lippel- poads
With Cruise Control, you can maintain a speed of about To Set. Cruise Cc-trol
25 mph (40 km/h) or more without keeping your foot on 1. Move the Cruise
the accelerator. This can really help on long trips. Cruise Co\
ntrol switch 'to
"ON."
Control does not work at speeds below about 25 mph ;.'
When you apply your brakes, the Cruise Control shuts i. 'I
.Off.
NOTE: On the Estate Wagon, if the tailgate window is
not completely closed the cruise control will not work.
(40 k-yn/h).

If you leave your Cruise Control si ch on when
you’re not using Cruise, you. might hit a button
and go into Cruise when you don’t want
to.. Yoe
could be startled and even lose control. Keel
I the Cruise Control switch “OFF’’ until you want
to use
it.
2. Get up to the speed you want.
3. Push in the set button
at the
end of ihe lever
and release
it.
(The “CRUISE’ light an
the instrument panel will
corne an.)
4. Take your foot off the. accelerator pedal.
To Resume a Set Speed
Suppose you set your Cruise Control at a desired speed
and then you apply the brake. This,
of course, shutsoff
the Cruise Control. But you don’t need to reset it. Once
you’re going- about 25 mph (40 h/h) or more, you can
move the Cruise Control switch from “ON’ to
“Resurne/Accelerate” for about half
a second.
95

,. ' .' ,
You'll go right back up to your chosen speed and stay
there.
, - .. .-
To Increase Speed While Using Crui-se
Control
There are
first:
1. Use th two ways
to go to a higher speed. Here's the.
e .accelerator pedal.
to get to the higher speed.
2. Push the button at the
end of the lever, then
release the buttmand
the accelerator pedal.
-You'll
now cruise at
the higher speed.

Here’s the second way to go to a higher speed:
2. To increase your speed in very small amounts, move
the switchdo ‘‘Resu~e/Accel~~ate” for less than half
a. second and then release it. Each time you do this,
your vehicle will
g,o about 1 mph (1.6 km/h) faster.
To Reduce Speed While Using Cruise
Control
1. Push in the burron at ,th
end
of the lever until.
you reach
the lower
speed YOU want, then
release it.,
.e
2. To slow down in very small amounts, push the
button for less than half
a second. .Each time you do
this, you’ll go 1 mph (1.6 h/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase ,your speed. When
you take your
foot off the pedal, your vehicle will slow
down to the Cruise Control speed you.set earlier.
97

Using LruIse Control on Hills
How well your Cruise Control will work on hills
depends upon your speed, load, and the steepness ofthe
hills. When going up steep hills, you may have to step
on the accelerator pedal to maintain: your speed. When
going downhill, you
may have to brake or shift to a
lower gear to keep your speed duwn.
Of course,
applying the brake takes you out of Cruise Control.
Many drivers find this to be too much trouble and don't
use Cruise Control
on steep hills., , .
To Get Out of Cruise'Control
There are two ways to turn off the Cruise Control:
1. Step lightly on the
., .-..
1; ;', , ;;brake pedal ; OR
! it
E
To Erase Speed Memory
When you turn off the Cruise Control or the ignition,
your Cruise Control .set speed memory is erased.