wheel CADILLAC CT5 2023 Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2023, Model line: CT5, Model: CADILLAC CT5 2023Pages: 526, PDF Size: 6.85 MB
Page 443 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
442 Vehicle Care
Each new wheel should have
the same load-carrying
capacity, diameter, width,
offset, and be mounted the
same way as the one it
replaces.
Replace wheels, wheel bolts,
wheel nuts, or Tire Pressure
Monitor System (TPMS)
sensors with new GM original
equipment parts.
{Warning
Using the wrong
replacement wheels, wheel
bolts, or wheel nuts can be
dangerous. It could affect
the braking and handling of
the vehicle. Tires can lose air
and cause loss of control,
resulting in a crash. Always
use the correct wheel, wheel
bolts, and wheel nuts for
replacement.
{Warning
Replacing a wheel with a
used one is dangerous. How
it has been used or how far
it has been driven may be
unknown. It could fail
suddenly and cause a crash.
When replacing wheels, use
a new GM original
equipment wheel.
Caution
The wrong wheel can also
cause problems with bearing
life, brake cooling,
speedometer or odometer
calibration, headlamp aim,
bumper height, vehicle
ground clearance, and tire or
tire chain clearance to the
body and chassis.
Tire Chains
{Warning
Do not use tire chains. There
is not enough clearance. Tire
chains used on a vehicle
without the proper amount
of clearance can cause
damage to the brakes,
suspension, or other vehicle
parts. The area damaged by
the tire chains could cause
loss of control and a crash.
Use another type of traction
device only if its
manufacturer recommends
it for the vehicle's tire size
combination and road
conditions. Follow that
manufacturer's instructions.
To avoid vehicle damage,
drive slowly and readjust or
remove the traction device if
it contacts the vehicle. Do
not spin the wheels.(Continued)
Page 444 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 443
Warning (Continued)
If traction devices are used,
install them on the tires of
the drive axle only.
If a Tire Goes Flat
It is unusual for a tire to blow
out while driving, especially if
the tires are maintained
properly. If air goes out of a
tire, it is much more likely to
leak out slowly. See Tires
0418 for additional
information. But if there ever
is a blowout, here are a few
tips about what to expect and
what to do:
If a front tire fails, the flat tire
creates a drag that pulls the
vehicle toward that side. Take
your foot off the accelerator
pedal and grip the steering
wheel firmly. Steer to maintain
lane position, and then gently
brake to a stop, well off the
road, if possible. A rear blowout, particularly on
a curve, acts much like a skid
and may require the same
correction as used in a skid.
Stop pressing the accelerator
pedal and steer to straighten
the vehicle. It may be very
bumpy and noisy. Gently brake
to a stop, well off the road,
if possible.
The vehicle has no spare tire,
no tire changing equipment,
and no place to store a tire.
If the vehicle has run-flat tires,
there is no need to stop on
the side of the road to change
a flat tire. See Run-Flat Tires
0
420.
If the vehicle has self-sealing
tires, see Self-Sealing Tires
0 420. Tread punctures
typically will not cause tires to
lose air. However, if the vehicle
does get a flat tire, there is no
spare tire, tire changing
equipment, or place to store a
tire. Contact Roadside
Assistance for help.
{Warning
Driving on a flat tire will
cause permanent damage to
the tire. Re-inflating a tire
after it has been driven on
while severely underinflated
or flat may cause a blowout
and a serious crash. Never
attempt to re-inflate a tire
that has been driven on
while severely underinflated
or flat. Have your dealer or
an authorized tire service
center repair or replace the
flat tire as soon as possible.
{Warning
Special tools and
procedures are required to
service a run-flat tire.
If these special tools and
procedures are not used,
injury or vehicle damage may
occur. Always be sure the
proper tools and
(Continued)
Page 445 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
444 Vehicle Care
Warning (Continued)
procedures, as described in
the service manual,
are used.
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place,
well off the road, if possible.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers 0156.
This vehicle may come with a
tire sealant and compressor
kit. To use the tire sealant and
compressor kit, see Tire
Sealant and Compressor Kit
0 444.
Tire Sealant and
Compressor Kit
{Warning
Idling a vehicle in an
enclosed area with poor
ventilation is dangerous.
Engine exhaust may enter
(Continued)
Warning (Continued)
the vehicle. Engine exhaust
contains carbon monoxide
(CO) which cannot be seen
or smelled. It can cause
unconsciousness and even
death. Never run the engine
in an enclosed area that has
no fresh air ventilation. For
more information, see
Engine Exhaust0276.
{Warning
Overinflating a tire could
cause the tire to rupture
and you or others could be
injured. Be sure to read and
follow the tire sealant and
compressor kit instructions
and inflate the tire to its
recommended pressure. Do
not exceed the
recommended pressure.
{Warning
Storing the tire sealant and
compressor kit or other
equipment in the passenger
compartment of the vehicle
could cause injury. In a
sudden stop or collision,
loose equipment could strike
someone. Store the tire
sealant and compressor kit
in its original location.
If this vehicle has a tire sealant
and compressor kit, there may
not be a spare tire or tire
changing equipment, and on
some vehicles there may not
be a place to store a tire.
The tire sealant and
compressor can be used to
temporarily seal punctures up
to 6 mm (0.25 in) in the tread
area of the tire. It can also be
used to inflate an
underinflated tire.
Page 446 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 445
If the vehicle is equipped with
tires containing acoustic foam,
tire sealant performance may
be decreased in cold climates.
If the tire has been separated
from the wheel, has damaged
sidewalls, or has a large
puncture, the tire is too
severely damaged for the tire
sealant and compressor kit to
be effective. See Roadside
Assistance Program0489.
Read and follow all of the tire
sealant and compressor kit
instructions.
The kit includes:1. Sealant Canister Inlet Valve
2. Sealant/Air Hose
3. Base of Sealant Canister
4. Tire Sealant Canister
5. On/Off Button
6. Slot on Top of Compressor
7. Pressure Deflation Button
8. Pressure Gauge
9. Power Plug
10. Air Only Hose
Tire Sealant
Read and follow the safe
handling instructions on the
label adhered to the tire
sealant canister (4).
Check the tire sealant
expiration date on the tire
sealant canister. The tire
sealant canister (4) should be
replaced before its expiration
date. Replacement tire sealant
canisters are available at your
local dealer.
There is only enough sealant
to seal one tire. After usage,
the tire sealant canister must
be replaced.
Using the Tire Sealant and
Compressor Kit to
Temporarily Seal and
Inflate a Punctured Tire
When using the tire sealant
and compressor kit during cold
temperatures, warm the kit in
a heated environment for
five minutes. This will help to
inflate the tire faster.
Page 447 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
446 Vehicle Care
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers0156.
See If a Tire Goes Flat 0443
for other important safety
warnings.
Do not remove any objects
that have penetrated the tire.
1. Remove the tire sealant canister (4) and
compressor from its
storage location. See
Storing the Tire Sealant
and Compressor Kit 0451.
2. Remove the air only hose (10) and the power plug (9)
from the bottom of the
compressor.
3. Place the compressor on the ground near the
flat tire.
4. Attach the air only hose(10) to the sealant canister
inlet valve (1) by turning it
clockwise until tight.
5. Slide the base of the tiresealant canister (3) into
the slot on the top of the
compressor (6) to hold it
upright.
Make sure the tire valve
stem is positioned close to
the ground so the hose will
reach it.
6. Remove the valve stem cap from the flat tire by
turning it
counterclockwise.
Page 450 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 449
If the tire pressure has not
dropped more than 68 kPa
(10 psi) from the
recommended inflation
pressure, inflate the tire to
the recommended inflation
pressure.
24. Wipe off any sealant from the wheel, tire, or vehicle.
25. Dispose of the used tire sealant canister (4) at a
local dealer or in
accordance with local
state codes and practices.
26. Replace it with a new canister available from
your dealer.
27. After temporarily sealing a tire using the tire sealant
and compressor kit, take
the vehicle to an
authorized dealer within
161 km (100 mi) of driving
to have the tire repaired or
replaced.Using the Tire Sealant and
Compressor Kit without
Sealant to Inflate a Tire
(Not Punctured)
The kit includes:
1. Sealant Canister Inlet Valve
2. Sealant/Air Hose
3. Base of Sealant Canister
4. Tire Sealant Canister
5. On/Off Button
6. Slot on Top of Compressor 7. Pressure Deflation
Button
8. Pressure Gauge
9. Power Plug
10. Air Only Hose
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers 0156.
See If a Tire Goes Flat 0443
for other important safety
warnings.
Page 458 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 457
Install the tow eye into the
socket and turn it until it is
fully tightened. When the tow
eye is removed, reinstall the
cover with the notch in the
original position.
Rear Tow Eye
If equipped, carefully open the
cover by using the small notch
that conceals the rear tow eye
socket. Install the tow eye into
the socket and turn it until it is
fully tightened. When the tow
eye is removed, reinstall the
cover with the notch in the
original position.
Recreational Vehicle
Towing
Caution
Dolly towing or dinghy
towing the vehicle may
cause damage because of
reduced ground clearance.
Always put the vehicle on a
flatbed truck or trailer.
The vehicle was neither
designed nor intended to be
towed with any of its wheels
on the ground. If the vehicle
must be towed, see
Transporting a Disabled
Vehicle 0455.
Appearance Care
Exterior Care
Locks
Locks are lubricated at the
factory. Use a de-icing agent
only when necessary, and have the locks greased after
using. See Recommended
Fluids and Lubricants
0476.
Washing the Vehicle
To preserve the vehicle finish,
wash it often and out of direct
sunlight.
Caution
Do not use
petroleum-based, acidic,
or abrasive cleaning agents
as they can damage the
vehicle's paint, metal,
or plastic parts. If damage
occurs, it would not be
covered by the vehicle
warranty. Approved cleaning
products can be obtained
from your dealer. Follow all
manufacturer directions
regarding correct product
usage, necessary safety
precautions, and
appropriate disposal of any
vehicle care product.
Page 459 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
458 Vehicle Care
Caution
Avoid using high-pressure
washes closer than 30 cm
(12 in) to the surface of the
vehicle. Use of power
washers exceeding
8 274 kPa (1,200 psi) can
result in damage or removal
of paint and decals.
Automatic Car Wash
Caution
Automatic car washes can
cause damage to the
vehicle, wheels, ground
effects, and convertible top
(if equipped).
Do not use automatic car
washes due to lack of
clearance for the
undercarriage, wide rear
tires, and wheels.
Caution
To avoid damage to a matte
paint finish, do not use an
automatic car wash
equipped with brushes or
scrubbers. Only use
touchless automatic car
washes.
If using an automatic car wash,
follow the car wash
instructions. The windshield
wiper and rear window wiper,
if equipped, must be off.
Remove any accessories that
may be damaged or interfere
with the car wash equipment.
Hand Wash
Rinse the vehicle well, before
and after washing, to remove
all cleaning agents completely.
If they are allowed to dry on
the surface, they could stain.
Dry the finish with a soft, clean
chamois or an all-cotton towel
to avoid surface scratches
and water spotting. Cleaning Underhood
ComponentsCaution
Do not power wash any
component under the hood
that has this
esymbol.
This could cause damage to
the vehicle that would not
be covered by the vehicle
warranty.
Avoid using solvents or
abrasive cleaners that may
harm underhood components.
GM recommends using only
water to clean underhood
components.
If using a pressure washer,
ensure the following criteria
is met:
.Water pressure must be
kept below 14 000 KPa
(2,000 PSI).
.Water temperature must be
below 80 °C (180 °F).
Page 462 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
Vehicle Care 461
The vehicle may have a
shutter system designed to
help improve fuel economy.
Always keep the shutter
system clear of debris, snow
and ice. If the check engine
light is activated, please check
to see if the shutter system is
clear of debris, snow or ice.
Windshield and Wiper
Blades
Clean the outside of the
windshield with glass cleaner.
Clean rubber wiper blades
using a lint-free cloth or paper
towel soaked with windshield
washer fluid or a mild
detergent. Wash the
windshield thoroughly when
cleaning the blades. Bugs,
road grime, sap, and a buildup
of vehicle wash/wax
treatments may cause wiper
streaking.
Replace the wiper blades if
they are worn or damaged.
Damage can be caused byextreme dusty conditions,
sand, salt, heat, sun, snow,
and ice.
Weatherstrips
Apply weatherstrip lubricant
on weatherstrips to make
them last longer, seal better,
and not stick or squeak.
Lubricate weatherstrips at
least once a year. Hot, dry
climates may require more
frequent application. Black
marks from rubber material on
painted surfaces can be
removed by rubbing with a
clean cloth. See
Recommended Fluids and
Lubricants
0476.
Tires
Use a stiff brush with tire
cleaner to clean the tires.
Caution
Using petroleum-based tire
dressing products on the
vehicle may damage the
paint finish and/or tires.
(Continued)
Caution (Continued)
When applying a tire
dressing, always wipe off
any overspray from all
painted surfaces on the
vehicle.
Wheels and Wheel Trim
Use a soft, clean cloth with
mild soap and water to clean
the wheels. After rinsing
thoroughly with clean water,
dry with a soft, clean towel.
A wax may then be applied.
Caution
Chrome wheels and chrome
wheel trim may be damaged
if the vehicle is not washed
after driving on roads that
have been sprayed with
magnesium chloride or
calcium chloride. These are
used on roads for conditions
such as dust control. Always
wash the chrome with soap
and water after exposure.
Page 463 of 526

Cadillac CT5 Owner Manual (GMNA-Localizing-U.S./Canada-16500419) -
2023 - CRC - 5/6/22
462 Vehicle Care
Caution
To avoid surface damage on
wheels and wheel trim, do
not use strong soaps,
chemicals, abrasive polishes,
cleaners, or brushes. Use
only GM approved cleaners.
Do not drive the vehicle
through an automatic car
wash that uses silicon
carbide tire/wheel cleaning
brushes. Damage could
occur and the repairs would
not be covered by the
vehicle warranty.
Brake System
Visually inspect brake lines
and hoses for proper hook-up,
binding, leaks, cracks, chafing,
etc. Inspect disc brake pads
for wear and rotors for
surface condition. Inspect
brake linings/shoes for wear
or cracks. Inspect all other
brake parts.
Steering, Suspension, and
Chassis Components
Visually inspect steering,
suspension, and chassis
components for damaged,
loose, or missing parts or signs
of wear at least once a year.
Inspect power steering for
proper attachment,
connections, binding, leaks,
cracks, chafing, etc.
Visually check constant
velocity joint boots and axle
seals for leaks.
Body Component
Lubrication
Lubricate all key lock cylinders,
hood hinges, liftgate hinges,
and the steel fuel door hinges,
unless the components are
plastic. Applying silicone
grease on weatherstrips with
a clean cloth will make them
last longer, seal better, and
not stick or squeak.
Underbody Maintenance
Every six months, use plain
water to flush any corrosive
materials from the underbody.
Take care to thoroughly clean
any areas where mud and
other debris can collect.
Do not directly power wash
the transfer case and/or
front/rear axle output seals.
High pressure water can
overcome the seals and
contaminate the fluid.
Contaminated fluid will
decrease the life of the
transfer case and/or axles and
should be replaced.
Sheet Metal Damage
If the vehicle is damaged and
requires sheet metal repair or
replacement, make sure the
body repair shop applies
anti-corrosion material to
parts repaired or replaced to
restore corrosion protection.