keyless CADILLAC DTS 2010 1.G User Guide

Instrument Panel Brightness
D(Instrument Panel Brightness):This feature
controls the brightness of the instrument paneland footwell lights, if equipped.
The button for this control is located below the exteriorlamps control.
Push the button in and release to extend the button.Turn the button clockwise or counterclockwise tobrighten or dim the lights.
Courtesy Lamps
The courtesy lamps are located on the headliner abovethe rear seat. These lamps come on by turning theinstrument panel brightness knob fully clockwise or whenany door is opened and it is dark outside. Puddle lampsare located on the bottom of the front and rear door trim.
Professional vehicles have an additional dome lampand also opera lamps.
Entry Lighting
This feature turns on the courtesy lamps and thebacklighting for the door switches and the exterior lampcontrol when a door is opened or if the remote keylessentry transmitter unlock button is pressed. If activateddue to the transmitter, the lighting remains active forabout 40 seconds. Since the entry lighting system usesthe light sensor, it must be dark outside in order for thecourtesy lamps to turn on. The courtesy lamps turn offapproximately 25 seconds after the last door is closed.They will dim to off if the ignition key is turned toON/RUN, or immediately deactivate if the power locksare activated.
Parade Dimming
This feature prohibits dimming of the digital displays andbacklighting during daylight hours when the key is inthe ignition and the headlamps are on. This feature isfully automatic. When the light sensor reads darknessoutside and the parking lamps are active, the digitaldisplays can be adjusted by turning the instrument panelbrightness knob counterclockwise to dim and clockwiseto brighten lighting.
4-31

RELEARN REMOTE KEY
This display allows you to match Remote KeylessEntry (RKE) transmitters to your vehicle. This procedurewill erase all previously learned transmitters. Therefore,they must be relearned as additional transmitters.
To match an RKE transmitter to your vehicle:
1. Press the vehicle information button until
PRESSVTO RELEARN REMOTE KEY displays.
2. Press the set/reset button until REMOTE KEYLEARNING ACTIVE is displayed.
3. Press and hold the lock and unlock buttons on thefirst transmitter at the same time for about15 seconds.
On vehicles with memory recall seats, the firsttransmitter learned will match driver 1 andthe second will match driver 2.
A chime will sound indicating that the transmitter ismatched.
4. To match additional transmitters at this time, repeatStep 3.
Each vehicle can have a maximum of eighttransmitters matched to it.
5. To exit the programming mode, you must cycle thekey to LOCK/OFF.
Blank Display
This display shows no information.
DIC Warnings and Messages
These messages appear if there is a problem detectedin one of your vehicle’s systems.
You must acknowledge a message to clear it from thescreen for further use. To clear a message, pressthe set/reset button.
Be sure to take any message that appears on thescreen seriously and remember that clearing themessage will only make the message disappear, notthe problem.
ADVISORY XXX MPH (km/h)
This message displays when the Speed Alert has beenturned on through the DIC Information Menu and thevehicle is at or above the advised speed. SeeDICOperation and Displays on page 4-62.
AUTOMATIC LIGHT CONTROL OFF
This message displays when the automatic headlampsare turned off. SeeExterior Lamps on page 4-25formore information.
4-67

PARKING ASSIST OFF
If your vehicle has the Ultrasonic Front and RearParking Assist (UFRPA) system, after the vehicle isshifted out of P (Park), this message displays to remindthe driver that the UFRPA system has been turnedoff. Press the set/reset button to acknowledge thismessage and clear it from the DIC display. To turn theUFRPA system back on, see “PARKING ASSIST”underDIC Operation and Displays on page 4-62. SeeUltrasonic Front and Rear Parking Assist (UFRPA)on page 3-40for more information.
PASSENGER DOOR OPEN
This symbol appears withthis message.
This message displays when the passenger side frontdoor is not closed completely. Make sure that the door isclosed completely.
RADAR CRUISE NOT READY
This message displays when the Adaptive CruiseControl (ACC) system will not activate due to atemporary condition. Your vehicle does not requireservice. If this message appears when you attempt toactivate the system, continue driving for several minutesand then try activating the system again. SeeAdaptiveCruise Control on page 4-15for more information.
REMOTE KEY LEARNING ACTIVE
This message displays while you are matching aRemote Keyless Entry (RKE) transmitter to your vehicle.See “Matching Transmitter(s) to Your Vehicle” underRemote Keyless Entry (RKE) System Operationon page 3-4andDIC Operation and Displays onpage 4-62for more information.
REPLACE BATTERY IN REMOTE KEY
This message displays when the battery in the RemoteKeyless Entry (RKE) transmitter needs to be replaced.To replace the battery, see “Battery Replacement” underRemote Keyless Entry (RKE) System Operation onpage 3-4.
4-73

AUTO DOOR UNLOCK
This feature allows you to select whether or not to turnoff the automatic door unlocking feature. It alsoallows you to select which doors and when the doorswill automatically unlock. SeeProgrammable AutomaticDoor Locks on page 3-10for more information.
Press the customization button until AUTO DOORUNLOCK appears on the DIC display. Press theset/reset button once to access the settings for thisfeature. Then press the menu up/down button to scrollthrough the following settings:
OFF:None of the doors will automatically unlock.
DRIVER AT KEY OUT:Only the driver’s door willunlock when the key is taken out of the ignition.
DRIVER IN PARK:Only the driver’s door will unlockwhen the vehicle is shifted into P (Park).
ALL AT KEY OUT:All of the doors will unlock whenthe key is taken out of the ignition.
ALL IN PARK (default):All of the doors will unlockwhen the vehicle is shifted into P (Park).
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
REMOTE DOOR LOCK
This feature allows you to select the type of feedbackyou will receive when locking the vehicle with theRemote Keyless Entry (RKE) transmitter. You will notreceive feedback when locking the vehicle with theRKE transmitter if the doors are open. SeeRemoteKeyless Entry (RKE) System Operation on page 3-4formore information.
Press the customization button until REMOTE DOORLOCK appears on the DIC display. Press the set/resetbutton once to access the settings for this feature.Then press the menu up/down button to scroll throughthe following settings:
OFF:There will be no feedback when you press thelock button on the RKE transmitter.
LIGHTS ONLY:The exterior lamps will flash when youpress the lock button on the RKE transmitter.
HORN ONLY:The horn will sound on the second pressof the lock button on the RKE transmitter.
HORN & LIGHTS (default):The exterior lamps willflash when you press the lock button on the RKEtransmitter, and the horn will sound when the lock buttonis pressed again within five seconds of the previouscommand.
NO CHANGE:No change will be made to this feature.
4-82

The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
REMOTE DOOR UNLOCK
This feature allows you to select the type of feedbackyou will receive when unlocking the vehicle withthe Remote Keyless Entry (RKE) transmitter. You willnot receive feedback when unlocking the vehiclewith the RKE transmitter if the doors are open. SeeRemote Keyless Entry (RKE) System Operationon page 3-4for more information.
Press the customization button until REMOTE DOORUNLOCK appears on the DIC display. Press theset/reset button once to access the settings for thisfeature. Then press the menu up/down button to scrollthrough the following settings:
LIGHTS OFF:The exterior lamps will not flash whenyou press the unlock button on the RKE transmitter.
LIGHTS ON (default):The exterior lamps willflash when you press the unlock button on theRKE transmitter.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
DELAY DOOR LOCK
This feature allows you to select whether or not thelocking of the vehicle’s doors will be delayed. Whenlocking the doors with the power door lock switch and adoor is open, this feature will delay locking the doorsuntil five seconds after the last door is closed. You willhear three chimes to signal that the delayed lockingfeature is in use. The key must be out of the ignition forthis feature to work. You can temporarily overridedelayed locking by pressing the power door lock switchtwice or the lock button on the RKE transmitter twice.
Press the customization button until DELAY DOORLOCK appears on the DIC display. Press the set/resetbutton once to access the settings for this feature.Then press the menu up/down button to scroll throughthe following settings:
OFF:There will be no delayed locking of thevehicle’s doors.
ON (default):The doors will not lock until five secondsafter the last door is closed.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
4-83

EXIT LIGHTING
This feature allows you to select the amount of time youwant the exterior lamps to remain on when it is darkenough outside. This happens after the key is turnedfrom ON/RUN to LOCK/OFF.
Press the customization button until EXIT LIGHTINGappears on the DIC display. Press the set/reset buttononce to access the settings for this feature. Thenpress the menu up/down button to scroll through thefollowing settings:
OFF:The exterior lamps will not turn on.
30 SECONDS (default):The exterior lamps will stayon for 30 seconds.
1 MINUTE:The exterior lamps will stay on forone minute.
2 MINUTES:The exterior lamps will stay on fortwo minutes.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
APPROACH LIGHTING
This feature allows you to select whether or not to havethe exterior lights turn on briefly during low lightperiods after unlocking the vehicle using the RemoteKeyless Entry (RKE) transmitter.
Press the customization button until APPROACHLIGHTING appears on the DIC display. Press theset/reset button once to access the settings forthis feature. Then press the menu up/down button toscroll through the following settings:
OFF:The exterior lights will not turn on when youunlock the vehicle with the RKE transmitter.
ON (default):If it is dark enough outside, the exteriorlights will turn on briefly when you unlock the vehiclewith the RKE transmitter.
The lights will remain on for 20 seconds or until the lockbutton on the RKE transmitter is pressed, or the vehicle isno longer off. SeeRemote Keyless Entry (RKE) SystemOperation on page 3-4for more information.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
4-84

ALL (default):The driver’s seat and the steering wheeltilt and steering column telescope features will recall,if your vehicle has this option.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
MEMORY SEAT RECALL
If your vehicle has this feature, it allows you to selectyour preference for the remote memory seat recallfeature. SeeMemory Seat, Mirrors and Steering Wheelon page 2-6for more information.
Press the customization button until MEMORY SEATRECALL appears on the DIC display. Press the set/resetbutton once to access the settings for this feature.Then press the menu up/down button to scroll throughthe following settings:
OFF (default):No remote memory seat recall will occur.
ON:The driver’s seat and outside mirrors willautomatically move to the stored driving position whenthe unlock button on the Remote Keyless Entry(RKE) transmitter is pressed. The steering column willalso move on vehicles with the power tilt and telescopicsteering feature. SeePower Tilt Wheel and TelescopicSteering Column on page 4-4for more information.
See “RELEARN REMOTE KEY” underDIC Operationand Displays on page 4-62for more information onmatching transmitters to driver ID numbers.
NO CHANGE:No change will be made to this feature.The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
REMOTE START
If your vehicle has this feature, it allows you to turn theremote start off or on. The remote start feature allowsyou to start the engine from outside of the vehicle usingthe Remote Keyless Entry (RKE) transmitter. SeeRemote Vehicle Start on page 3-7for more information.
Press the customization button until REMOTE STARTappears on the DIC display. Press the set/reset buttononce to access the settings for this feature. Then pressthe menu up/down button to scroll through the followingsettings:
OFF:The remote start feature will be disabled.
ON (default):The remote start feature will be enabled.
NO CHANGE:No change will be made to thisfeature. The current setting will remain.
To select a setting, press the set/reset button while thedesired setting is displayed on the DIC.
4-87

California Proposition 65 Warning
Most motor vehicles, including this one, contain and/oremit chemicals known to the State of California tocause cancer and birth defects or other reproductiveharm. Engine exhaust, many parts and systems, manyfluids, and some component wear by-productscontain and/or emit these chemicals.
California Perchlorate Materials
Requirements
Certain types of automotive applications, such as airbaginitiators, seat belt pretensioners, and lithium batteriescontained in remote keyless transmitters, maycontain perchlorate materials. Special handling may benecessary. For additional information, seewww.dtsc.ca.gov/hazardouswaste/perchlorate.
Doing Your Own Service Work
{WARNING:
You can be injured and the vehicle could be
damaged if you try to do service work on a vehicle
without knowing enough about it.
•Be sure you have sufficient knowledge,
experience, the proper replacement parts, andtools before attempting any vehiclemaintenance task.
•Be sure to use the proper nuts, bolts, and
other fasteners. English and metric fastenerscan be easily confused. If the wrong fastenersare used, parts can later break or fall off. Youcould be hurt.
If doing some of your own service work, use the properservice manual. It tells you much more about how toservice the vehicle than this manual can. To orderthe proper service manual, seeService PublicationsOrdering Information on page 8-17.
This vehicle has an airbag system. Before attempting todo your own service work, seeServicing YourAirbag-Equipped Vehicle on page 2-72.
6-4

The TPMS sensor matching process is outlined below:
1. Set the parking brake.
2. Turn the ignition switch to ON/RUN with theengine off.
3. Press the Remote Keyless Entry (RKE) transmitter’slock and unlock buttons at the same time forapproximately five seconds. The horn sounds twiceto signal the receiver is in relearn mode andTIRE LEARNING ACTIVE message displays on theDIC screen.
4. Start with the driver side front tire.
5. Remove the valve cap from the valve cap stem.Activate the TPMS sensor by increasing ordecreasing the tire’s air pressure for five seconds,or until a horn chirp sounds. The horn chirp,which may take up to 30 seconds to sound,confirms that the sensor identification code hasbeen matched to this tire and wheel position.
6. Proceed to the passenger side front tire, and repeatthe procedure in Step 5.
7. Proceed to the passenger side rear tire, and repeatthe procedure in Step 5.
8. Proceed to the driver side rear tire, and repeat theprocedure in Step 5. The horn sounds two times toindicate the sensor identification code has beenmatched to the driver side rear tire, and theTPMS sensor matching process is no longer active.The TIRE LEARNING ACTIVE message on theDIC display screen goes off.
9. Turn the ignition switch to LOCK/OFF.
10. Set all four tires to the recommended air pressurelevel as indicated on the Tire and LoadingInformation label.
11. Put the valve caps back on the valve stems.
6-61

H
Hazard Warning Flashers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2Headlamp Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-100HeadlampsAiming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-40Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-43Daytime Running Lamps (DRL) . . . . . . . . . . . . . . . . . . . . . 4-29Exterior Lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25Flash-to-Pass . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10High Intensity Discharge (HID) Lighting . . . . . . . . . . . 6-43High/Low Beam Changer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6On Reminder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29Wiper Activated . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-29HeatedSteering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4Heated Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5HeaterEngine Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26Highbeam On Light . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-61High-Speed Operation, Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-56Highway Hypnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13Hill and Mountain Roads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14HoodChecking Things Under . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-10Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11Horn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3How to Wear Safety Belts Properly . . . . . . . . . . . . . . . . . . . 2-17
I
Ignition Positions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23Inadvertent Power Battery Saver . . . . . . . . . . . . . . . . . . . . . . . 4-33Infants and Young Children, Restraints . . . . . . . . . . . . . . . 2-37Inflation - Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-54Instrument PanelBrightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-31Cluster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-47Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
J
Jump Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-36
K
Keyless EntryRemote (RKE) System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Keyless Entry System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
7