wheel CADILLAC STS 2011 1.G Owners Manual

Black plate (97,1)Cadillac STS Owner Manual - 2011
The tools you will be using include the jack (A) and the
wheel wrench (B).
Removing the Flat Tire and Installing
the Spare Tire
1. Do a safety check before proceeding. SeeChanging a Flat Tireon page 6‑94for more
information.
2. Loosen all of the wheel nuts, but do not remove them yet, using the wheel wrench. Turn the handle
about 180 degrees, then flip the handle back to the
starting position. This avoids taking the wrench off
the lug nut for each turn.
6-97

Black plate (98,1)Cadillac STS Owner Manual - 2011
3. Find the vehicle's jacking location using thediagram above and corresponding V–shaped
notches located in the plastic molding on the
vehicle's frame. The notches in the plastic molding
are marked with a triangle shape.
4. Attach the wheel wrench to the jack.
{WARNING:
Getting under a vehicle when it is jacked up is
dangerous. If the vehicle slips off the jack, you
could be badly injured or killed. Never get under a
vehicle when it is supported only by a jack.
{WARNING:
Raising your vehicle with the jack improperly
positioned can damage the vehicle and even
make the vehicle fall. To help avoid personal
injury and vehicle damage, be sure to fit the jack
lift head into the proper location before raising the
vehicle.
6-98

Black plate (99,1)Cadillac STS Owner Manual - 2011
{WARNING:
Lifting a vehicle and getting under it to do
maintenance or repairs is dangerous without the
appropriate safety equipment and training. If a
jack is provided with the vehicle, it is designed
only for changing a flat tire. If it is used for
anything else, you or others could be badly
injured or killed if the vehicle slips off the jack. If a
jack is provided with the vehicle, only use it for
changing a flat tire.
Notice: If you position the jack under the rocker
molding and attempt to raise the vehicle, you could
break the molding and/or cause other damage to
your vehicle. Always position the jack so that when
the jack head is raised, it will fit firmly in the notch
located inboard from the rocker molding.
5. Turn the wheel wrench counterclockwise to lower the jack lift head until the jack fits under the
vehicle.
6. Raise the jack by turning the wheel wrenchclockwise until the slots in the jack head fit into the
metal flange located behind the triangle on the
plastic molding as shown.
7. Put the compact spare tire near you.
6-99

Black plate (100,1)Cadillac STS Owner Manual - 2011
8. Raise the vehicle by turning the wheel wrenchclockwise. Raise the vehicle far enough off the
ground for the compact spare tire to fit under the
vehicle.
9. Remove all the wheel
nuts and the flat tire.
{WARNING:
Rust or dirt on a wheel, or on the parts to which it
is fastened, can make wheel nuts become loose
after time. The wheel could come off and cause
an accident. When changing a wheel, remove any
rust or dirt from places where the wheel attaches
(Continued)
6-100

Black plate (101,1)Cadillac STS Owner Manual - 2011
WARNING: (Continued)
to the vehicle. In an emergency, use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if needed, to get all the
rust or dirt off. SeeChanging a Flat Tire
on
page 6‑94
.
{WARNING:
Never use oil or grease on bolts or nuts because
the nuts might come loose. The vehicle's wheel
could fall off, causing a crash.
10. Remove any rust or dirt from the wheel bolts,
mounting surfaces, and
spare wheel.
11. Install the spare tire.
12. Put the wheel nuts back on with the rounded end of the nuts toward the wheel.
13. Tighten each wheel nut by turning it clockwise with your hand until the wheel is held against the hub.
6-101

Black plate (102,1)Cadillac STS Owner Manual - 2011
14. Lower the vehicle by turning the wheel wrenchcounterclockwise. Lower the jack completely.
{WARNING:
Wheel nuts that are improperly or incorrectly
tightened can cause the wheels to become loose
or come off. The wheel nuts should be tightened
with a torque wrench to the proper torque
specification after replacing. Follow the torque
specification supplied by the aftermarket
manufacturer when using accessory locking wheel
nuts. See Capacities and Specifications
on
page 6‑128
for original equipment wheel nut
torque specifications.
Notice: Improperly tightened wheel nuts can lead
to brake pulsation and rotor damage. To avoid
expensive brake repairs, evenly tighten the wheel
nuts in the proper sequence and to the proper
torque specification. See Capacities and
Specifications
on page 6‑128for the wheel nut
torque specification.
6-102

Black plate (103,1)Cadillac STS Owner Manual - 2011
15. Tighten the wheel nutsfirmly in a crisscross
sequence as shown.
Storing a Flat or Spare Tire and
Tools
{WARNING:
Storing a jack, a tire, or other equipment in the
passenger compartment of the vehicle could
cause injury. In a sudden stop or collision, loose
equipment could strike someone. Store all these
in the proper place.
Full-Size Tire and Tools
After you have put the compact spare tire on your
vehicle, you will need to do the following to store the flat
tire in your trunk.
1. Open the trunk. See Trunk
on page 3‑15.
2. Store the jack and wheel wrench in the jack container in the trunk.
When storing the jack, in the container, it must be
raised until the screw end is flush with the edge of
the jack.
3. Store the flat tire as far forward in the trunk as possible.
The compact spare is for temporary use only. Replace
the compact spare tire with a full-size tire as soon as
you can.
6-103

Black plate (104,1)Cadillac STS Owner Manual - 2011
Compact Spare Tire and Tools
Use the following diagram as a guide for storing the
compact spare tire and tools in the trunk:
A. Compact SpareTire Cover
B. Stow Rod Cap
C. Plastic Wing Nut
D. Retainer E. Jack Container Package
(With Wheel Wrench
and Jack)
F. Compact Spare Tire
G. Foam Support H. Bolt 1. Open the trunk. See
Trunk on page 3‑15.
2. Make sure the foam support (G) is in place in the trunk area.
3. Reinstall the compact spare tire (F) making sure to line up the wheel center hole with the bolt (H) and
place on the compartment floor.
4. Insert the jack container (E) with wheel wrench and jack into the center of the compact spare tire
making sure to line up the wheel nut hole with the
bolt (H) on the compartment floor.
5. Secure the tire and wheel with the retainer (D) and wing nut (C).
6. Cover the exposed bolt with the stow rod cap (B).
7. Reinstall the compact spare tire cover (A).
6-104

Black plate (105,1)Cadillac STS Owner Manual - 2011
Compact Spare Tire
{WARNING:
Driving with more than one compact spare tire at
a time could result in loss of braking and handling.
This could lead to a crash and you or others could
be injured. Use only one compact spare tire at
a time.
Although the compact spare tire was fully inflated when
the vehicle was new, it can lose air after a time. Check
the inflation pressure regularly. It should be 60 psi
(420 kPa).
After installing the compact spare on the vehicle, you
should stop as soon as possible and make sure the
spare tire is correctly inflated. The compact spare
is made to perform well at speeds up to 65 mph
(105 km/h) for distances up to 3,000 miles (5 000 km),
so you can finish your trip and have the full-size tire repaired or replaced where you want. You must
calibrate the tire inflation monitor system after installing
or removing the compact spare. See
Tire Pressure
Monitor System
on page 6‑60. The system may not
work correctly when the compact spare is installed on
the vehicle. Of course, it's best to replace the spare with
a full-size tire as soon as you can. The spare will last
longer and be in good shape in case you need it again.
Notice: When the compact spare is installed, do not
take the vehicle through an automatic car wash with
guide rails. The compact spare can get caught on
the rails which can damage the tire, wheel and other
parts of the vehicle.
Do not use the compact spare on other vehicles.
And do not mix the compact spare tire or wheel with
other wheels or tires. They will not fit. Keep the spare
tire and its wheel together.
Notice: Tire chains will not fit the compact spare.
Using them can damage the vehicle and can
damage the chains too. Do not use tire chains on
the compact spare.
6-105

Black plate (112,1)Cadillac STS Owner Manual - 2011
Aluminum or Chrome-Plated Wheels
and Trim
The vehicle may have either aluminum or
chrome-plated wheels.
Keep the wheels clean using a soft clean cloth with mild
soap and water. Rinse with clean water. After rinsing
thoroughly, dry with a soft clean towel. A wax may then
be applied.
Notice:Chrome wheels and other chrome trim
may be damaged if the vehicle is not washed after
driving on roads that have been sprayed with
magnesium, calcium or sodium chloride. These
chlorides are used on roads for conditions such as
ice and dust. Always wash the vehicle's chrome
with soap and water after exposure.
Notice: Using strong soaps, chemicals, abrasive
polishes, cleaners, brushes, or cleaners that contain
acid on aluminum or chrome-plated wheels, could
damage the surface of the wheel(s). The repairs
would not be covered by the vehicle warranty. Use
only approved cleaners on aluminum or
chrome-plated wheels. The surface of these wheels is similar to the painted
surface of the vehicle. Do not use strong soaps,
chemicals, abrasive polishes, abrasive cleaners,
cleaners with acid, or abrasive cleaning brushes on
them because they could damage the surface. Do not
use chrome polish on aluminum wheels.
Notice:
Using chrome polish on aluminum wheels
could damage the wheels. The repairs would not be
covered by the vehicle warranty. Use chrome polish
on chrome wheels only.
Use chrome polish only on chrome-plated wheels, but
avoid any painted surface of the wheel, and buff off
immediately after application.
Notice: Driving the vehicle through an automatic
car wash that has silicone carbide tire cleaning
brushes, could damage the aluminum or
chrome-plated wheels. The repairs would not be
covered by the vehicle warranty. Never drive a
vehicle that has aluminum or chrome-plated wheels
through an automatic car wash that uses silicone
carbide tire cleaning brushes.
6-112