ignition CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine 4.CHECK RESTRAINTS CONTROL MODULE (RCM) POWER SUPPLY
• Turn ignition switch on.
• Check RCM power supply between terminal 5 and
terminal 6 in the RCM electrical connector J-001
terminal side.
Is the voltage less than 9 V?
Ye s>>Go to step 5.
No
>>Replace the RCM.
5.CHECK DTC
• With the X-431 scan tool, read RCM DTCs.
• Refer to DTC Confirmation Procedure.
Is DTC B1620 still present?
Ye s>>Replace the RCM.
No
>>The system is now operating properly.
Reassemble the vehicle and road test to verify the customers complaint is repaired.
DIAGNOSIS & TESTING
LTSMD140001
14
14–45Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Airbag System Disarming Procedure
Description
WARNING!
The steering column contains the driver’s airbag. The airbag system is a sensitive, complex electro-mechanical
unit. Before attempting to diagnose, remove or install the airbag system components, you must first disconnect
and isolate the negative battery (ground) cable. Then wait two minutes for the system capacitor to discharge.
Failure to do so could result in accidental deployment of the airbag and possible personal injury. The fasteners,
screws, and bolts, originally used for the airbag components, have special coatings and are specifically
designed for the airbag system. They must never be replaced with any substitutes. Anytime a new fastener is
needed, replace with the correct fasteners provided in the service package or fasteners listed in the parts books.
1. Turn the ignition off.
2. Disconnect and isolate the negative battery cable.
3. Wait two minutes for the system capacitor to discharge.
4. The airbag system can now be serviced safely.
Driver Side Airbag
Removal & Installation
1. Turn the ignition off.
2. Disconnect the negative battery cable.
WARNING!
Wait two minutes for the airbag system reserve capacitor to discharge before beginning any airbag system or
component service. Failure to do so may result in accidental airbag development, serious or fatal injury (See
Airbag System Disarming Procedure in Section 14 Restraints).
3. Remove the two driver side airbag retaining bolts (1).(Tighten: Driver side airbag retaining bolts to 10
N·m)
4. Remove the driver side airbag and disconnect the airbag squib electrical connector.
5. Installation is in the reverse order of removal.
LTSM140001
14–46Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Front Passenger Side Airbag
Removal & Installation
1. Turn the ignition off.
2. Disconnect the negative battery cable.
WARNING!
Wait two minutes for the airbag system reserve capacitor to discharge before beginning any airbag system or
component service. Failure to do so may result in accidental airbag development, serious or fatal injury (See
Airbag System Disarming Procedure in Section 14 Restraints).
3. Remove the two glove box mounting bolts (1).
ON-VEHICLE SERVICE
LTSM150086
14
14–47Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Restraints Control Module (RCM)
Removal & Installation
1. Turn the ignition off.
2. Disconnect the negative battery cable.
WARNING!
Wait two minutes for the airbag system reserve capacitor to discharge before beginning any airbag system or
component service. Failure to do so may result in accidental airbag development, serious or fatal injury (See
Airbag System Disarming Procedure in Section 14 Restraints).
3. Remove the center console (See Center Console Removal & Installation in Section 15 Body & Accessories).
4. Disconnect the Restraints Control Module (RCM)electrical connector (1).
5. Remove the RCM retaining bolts (2). (Tighten: RCM retaining bolts to 7-9 N·m)
6. Remove the RCM from the vehicle.
7. Installation is in the reverse order of the removal.
ON-VEHICLE SERVICE
LTSM140006
14
14–49Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Front Seat Belt and Pre-Tensioner
Removal & Installation
1. Turn the ignition off.
2. Disconnect the negative battery cable.
3. Remove the seat belt upper mounting bolt (1).
4. Remove the seat belt lower mounting bolt (1).
5. Remove the B-pillar lower trim panel.
LTSM150077
LTSM150076
14–52Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6. Remove the front seat belt pre-tensioner retainingbolt (1) and screw (2).
(Tighten: Front seat belt retaining bolt to 50 N·m)
7. Remove the front seat belt and pre-tensioner.
8. Installation is in the reverse order of removal.
Seat Belt Slider Track
Removal & Installation
1. Turn the ignition off.
2. Remove the seat belt upper mounting bolt (1).
3. Remove the B-pillar upper trim panel.
ON-VEHICLE SERVICE
LTSM140003
LTSM150077
14
14–53Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4. Remove the two bolts (1) and then remove theseat belt slider track.
(Tighten: Adjustable shoulder belt anchor bolts to
50 N·m)
5. Installation is in the reverse order of the removal.
Rear Seat Belt and Pre-Tensioner
Removal & Installation
1. Turn the ignition off.
2. Remove the rear seat belt mounting bolts (1). (Tighten: Rear seat belt mounting bolts to 50 N·m)
3. Remove the C-pillar (See C-pillar Trim Panel Remove & Installation in Section 15 Body & Acces-
sories).
ON-VEHICLE SERVICE
BESM140006
LTSM140005
14–54Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine AUDIO SYSTEM
Description
The audio system consists of the following components:
•Audio Unit
• Front Speakers
• Front Tweeters
• Rear Speakers
• Window Antenna (audio)
The audio system is standard factory-installed equipment. The system uses an ignition switched source of battery
current so that the system will operate when the ignition switch is in the LOCK/ACC/ON positions. The system will
also operate in the OFF position for one hour.
Operation
With the audio system on, radio signals are received by the window antenna, the audio unit then sends audio signals
to front speakers and rear speakers.
15–4Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DOOR LOCKS
Description
The power door locks allow the doors to be locked or unlocked electronically. The power door lock switch is located
on the front door trim panel. The power door locks can also be operated by the Remote Keyless Entry (RKE) trans-
mitter.
Operation
The power lock system receives non-switched battery current, so that the power locks remain operational, regardless
of the ignition switch position. The power lock system is controlled by BCM.
15
15–29Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Door Lock Switch
Removal & Installation
1. Turn the ignition switch off.
2. Remove the power window and door lock/unlockswitch bezel mounting screw (1).
3. Using a trim stick, pry out the power window and door lock/unlock switch assembly from the front door.
4. Disconnect the power window and door lock/unlock switch electrical connectors.
5. Remove the power window and door lock/unlock switch retaining screws to remove the power window and door lock/unlock switch.
6. Installation is in the reverse order of removal
Door Lock Assembly
Removal & Installation
NOTE :
The passenger door is shown, all other doors are similar.
1. Disconnect the negative battery cable.
2. Turn the ignition switch off.
3. Using a small trim stick, remove the pull handle cover (1) from the pull handle (2).
DOOR LOCKS
LTSM150097
LTSM150139
15
15–35Chery Automobile Co., Ltd.