hood open CHEVROLET CAMARO 1967 1.G Chassis Owner's Manual

CHASSIS SHEET METAL 11-15

FRONT FENDER TRIM

If fender spear molding is to be replaced without re-

moving fender from vehicle, proceed as follows:

1.
Perform Operations 2 and 5 only of Front Fender

Assembly—Removal.

2.
Pull rear* end of fender away from body far enough

to insert a short piece of 2 x 4 between lower rear

corner of fender and rocker panel extension.

3.
It should now be possible to gain access to first and

second retaining nuts forward of rear end of fender.

All other nuts can be reached from front wheel

opening.

SKIRT ASSEMBLY

Removal

1.
Remove hood and hinge assemblies as outlined in

this section.

2.
Remove grille and radiator support as outlined in

Section ia.

3.
Remove fender assembly as outlined in this section.

4.
Raise car from floor and place jack stands under

rocker panel extension.
5.
Remove suspension bumper support, shock absorber,

front spring and stabilizer link as outlined in Section

3.

6. If removing left skirt assembly, remove steering

gear mounting bolts, power steering hose clamp (if

so equipped) and outer (left) clutch cordon shaft

bracket (if so equipped).

7.
Remove tie rod ball stud from steering arm as out-

lined in Section 9.

8. Support engine and remove engine mount cushion as

outlined in Section 6.

9. Remove spring clip from brake line junction which

passes through skirt and remove junction from skirt

(see Section 5).

10.
Remove four bolts retaining front crossmember to

skirt.

11.
Remove four bolts retaining skirt assembly to dash

front brace. Remove 3 bolts retaining upper end of

skirt to dash (fig. 26); record shims removed.

12.
Remove skirt assembly with remaining suspension

parts attached as shown in Figure 27.

13.
Suspension parts may be detached as outlined in

Section 3.

Fig.
22 - Radiator Support Assembly

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-18

b.
Check and adjust front wheel alignment as out-

lined in Section 3.

c. Check and adjust headlamp aiming as outlined in

Section 12.

HOOD ASSEMBLY

Hood may be removed either with or without hinges.

To shorten aligning time, hood hinge plates may be lo-

cated by scribing a mark on hood and/or body which

outlines entire plate. See Maintenance and Adjustments -

Hood Hinge for hood adjustment procedure. Hood hinge

springs may be easily and safely removed and installed.

through the use of Tool J-9559 as follows:

1.
With hood opened only far enough to allow passage of

mechanic's arm between hood and fender, insert ends

of J-9559 (through bolt removed) between coils of

spring until barrel of tool contacts outer diameter

of spring.

2.
Open hood fully while still holding spring (with tool

installed) in hand; when hood is near fully opened

position, spring may be removed as shown in Figure

28.

3.
As soon as spring is removed, insert long bolt sup-

plied with J-9559 through holes in end of tool, pass-

ing it through spring, and install nut on bolt.

Spring may be removed from J-9559 or J-9559 may be

installed in a new spring by the following method:

1.
Place a closed 6 or 8 inch "C" clamp in a vise or

fasten it to a heavy bench top (bench should be fas-

tened to floor).

2.
Hook one end of spring in clamp and the other end

in hook of a hoist as shown in Figure 29.

3.
Stretch the spring enough to allow insertion of

J-9559. Install through bolt if spring is not to be

installed on hinge at once.

HOOD CATCH AMD LOCK (Fig. 19)

Removal

1.
Remove catch assembly as follows:

a. Remove screws retaining catch assembly to radi-

ator support.

b.
Remove screws retaining catch assembly to catch

support assembly.

c* Remove screws retaining catch assembly to grille

upper bar.

2.
Before removing hood lock plate from hood, locate

position on hood by scribing around base of lock

plate. Remove screws retaining lock plate to hood

and remove lock plate from vehicle.

Installation

1.
Install both catch and lock assemblies in reverse

order of removal procedure.

2.
Align as outlined under Maintenance and Adjust-

ments - Hood Catch.

HOOD TRIM

Crown Molding

Hood crown molding is retained by clips installed on

underside of hood. Clips may be removed by carefully

pressing them off molding mounting studs with screw

driver.
When installing a new molding, force clips onto mount-

ing studs as far as possible and then clench clips with

long-nosed pliers to eliminate gap between molding and

hood, as shown in Figure 30.

Emblem

The hood emblem is retained by four nuts which are

accessible from under the hood.

COWL VENT GRILLE

The cowl vent grille replacement procedure for Chevy

U is the same as for Chevrolet and Chevelle. Refer to

Chevrolet and Chevelle Cowl Vent Grille replacement

procedure and see Figure 16.

FRONT END ASSEMBLY

The Chevy n front end body design allows for removal

of the entire front end of the vehicle without disassembly

of front suspension of sheet metal. One man may remove

and transport the front end assembly using only a floor

jack placed under the crossmember and the vehicle front

wheels. Figure 31 illustrates the assembly in process

of removal with jack stand in position under rocker panel.

Proceed with removal
as.
follows:

Removal

1.
Remove hood assembly as outlined in this section.

2.
Remove engine assembly as outlined in Section 6.

On 4 cylinder models, replace crossmember.

3.
Raise car from floor and install jack stands as

shown in Figure 31.

4.
Remove pitman arm from steering gear as outlined

in Section 9.

5.
Remove steering gear mounting bolts from skirt

assembly.

6. Remove 4 bolts securing each skirt assembly to

lower dash brace.

7.
Remove fender-to-rocker extension mounting screws

and record shimming.

8. Remove brake hydraulic line and fuel line from right

hand skirt.

9. Position floor jack or equivalent under front cross-

member.

10.
Remove hydraulic line from main cylinder.

11.
Remove fender-to-cowl mounting screws and record

shimming.

12.
Remove upper skirt-to-dash mounting screws and

record shimming.

13.
Remove front end from vehicle as shown in Figure

31.

Inspection

If car has been involved in a collision, it is advisable

to carefully inspect cowl and dash area for damage. Pay

particular attention to welds, cage nuts, weld nuts and

skirt mounting surfaces. Cage and weld nuts may be

repaired by outright replacement (the best method), or

by the installation of spiral thread inserts. If the spiral

inserts are used, follow the instructions furnished by the

manufacturer. -

Installation

%, position front end assembly at upper dash mounts

and lower dash support, align screw holes with drift

punch and install all mounting screws and bolts

loosely; do not tighten until all screws and bolts are

started. Replace original shimming.

CHEVROLET CHASSIS SERVICE MANUAL

CHASSIS SHEET METAL 11-20

GENERAL DESCRIPTION

The Camaro sheet metal components are much the

same as other Chevrolet passenger models as shown in

Figure 32. The front end design is such that servicing

of the fenders and skirts is most efficiently performed
by removing the fender and skirt as an assembly. Refer

to Section 14 for bumper service procedures, Section 13

for radiator and grille, and Section 1A for air condition-

ing components.

MAINTENANCE AND ADJUSTMENTS

HOOD ADJUSTMENT

The Camaro hood is adjusted in the conventional man-

ner, by adjustment of the hood bumpers and hinges. The

two hood bumpers are located on each side at the top of

the radiator support. Do not attempt hood latch adjust-

ments until the hinges and bumpers are correctly ad-

justed. Latch adjustments are made so that effort re-

quired to open and close the hood is reasonable, and

hood alignment obtained by hinge and bumper adjust-

ment is maintained when the hood is closed. Note that

the hood latch is not designed to correct basic hood mis-

alignment.

HOOD HINGE (Fig. 33)

NOTE: The body mounted portion of the hood

hinges are slotted to provide up and down move-

ment. The hood mounted end is slotted to pro-

vide forward and rearward movement.

1.
Scribe a. line around the entire. hinge plate to be

repositioned.

2.
Loosen the appropriate screws and shift the position

of the hood into correct alignment using the scribe

marks to check amount of movement. Check align-

ment by tightening screws and closing the hood.

HOOD BUMPERS

Adjust hood bumpers so that hood top surface is flush

with fender and header panel top surfaces. See Figure

34 for correct sheet metal adjustment dimensions.

HOOD CATCH AND LOCK (Fig. 35)

Adjust hood lock bolt so that top surface of hood is

flush with top surface'of header panel. The distance that

the lock bolt protrudes out of the lock plate should be

adjusted so that the hood bumpers are slightly com-

pressed by the fully latched hood, and effort required

to release the hood catch is reasonable. Close the hood

and insure catch engages securely.

FENDERS

Fenders are adjustable with shims at the cowl and

rocker panel. To add or remove shims, loosen bolts
Fig. 33 - Hood Hinge - Camaro

at shim locations (fig. 36) and carefully apply force with

pry bar to provide clearance for shim removal or in-

stallation.

SHEET METAL

For proper operation of doors and hood, and for pre-

sentable appearance, adjust front sheet metal to the di-

mensions shown in Figure 34.

COMPONENT PART REPLACEMENT

NOTE: When replacing sheet metal compo-

nents on Camaro, note position and attachment

of all seals and dust shielding and replace if

necessary.

BATTERY TRAY

Removal

1.
Disconnect battery cables and remove battery from

vehicle.

2.
Remove screws securing battery tray to fender skirt

and radiator support.

3.
Remove battery tray from vehicle.
Installation

Install battery tray following removal procedure in

reverse order.

RADIATOR SUPPORT

Removal

1.
Raise hood, disconnect battery cables, and remove

battery.

2.
Remove front bumper (Section 14).

3.
Remove grille and related components (Section 13).

4.
Disconnect horns, horn relay, voltage regulator,

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-5

Fig.
8—Turning Level Adjusting Screw to Calibrate Aimer

HEADLAMP PANEL TRAVEL ADJUSTMENT

Corvette (Fig. 9)

The headlamp panel travel is limited by two adjusting

screws which are located on the arms of the shaft

mounted stop.
Fig.
9—Headlamp Panel Travel Adjusting Screw

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Adjusting screw (A) limits headlamp panel travel in

open position - adjust this screw so that mounting

face of panel is within 2 degrees of vertical in the

fully open position.

NOTE: Each headlamp operates independently

of the other, therefore individual adjustment is

required for each panel.

3.
Adjusting screw (B) limits headlamp panel travel in

closed position - adjust this screw so that panel is

flush to upper body panel in the fully closed position.

4.
Lock both screws by tightening lock nut against stop.

5.
Remove safety bolt as installed in Step 1 and close

the hood.

SERVICE OPERATIONS

FRONT LIGHTING

HEADLAMP REPLACEMENT (Figs. 10 and 13)

1.
On Corvette and Camaro Rally Sport models, rotate

the headlamp panel to the open position.

2.
Remove headlamp bezel retaining screws and remove

bezel. On Chevrolet, Chevelle and Camaro models

lift bezel to disengage retaining tabs from slots in

filler panel.

3.
On Chevy n models remove three retaining ring at-

taching screws. On other models disengage spring

from the retaining ring and remove two attaching

screws.

4.
Remove retaining ring, disconnect sealed beam unit

at wiring connector and remove the unit.

5.
Attach connector to replacement unit and position

unit in place making sure the number molded into the

lens face is at the top.

NOTE: In the dual headlamp installation the

inboard unit (NO. 1) takes a double connector, the
outboard unit (No. 2) takes a triple connector

plug.

6. Position retaining ring into place and install the re-

taining ring attaching screws and spring (as

applicable).

7.
Check operation of unit and install the headlamp

bezel.

PARKING LAMP REPLACEMENT

Bulb

1.
Remove two lens retaining screws and disengage lens

from housing.

2.
Replace bulb, check operation of lamp, reinstall lens

and retaining screws.

Lamp Housing

Chevrolet, Chevelle and Chevy II (Figs. 10 and 11)

1.
Disconnect lamp wire assembly in-line connector

from wiring harness.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-6

\ \

CHEVROLET
CHEVELLE

CHEVY II
CAMARO

Fig.
10 - Headlamp Assemblies (Exc. Corvette)

1.
2.
Remove two bolts retaining housing assembly in Corvette (Fig. 12)

bumper and remove housing.

3.
Remove lens retaining screws, lens and bulb from

housing assembly and transfer to new housing unit.

4.
Connect lamp wiring assembly to harness assembly,

housing and check operation of lamp.

5. Position lamp assembly in place and.install retaining

bolts.

Camaro (Fig. 10)

1.
Raise hood.

2.
Disconnect wiring harness at rear of lamp socket.

3.
Remove attaching nut and disconnect ground wire at

sheet metal connection.

4.
Remove retaining nuts and housing from grille

opening.

5. Transfer lens and bulb to new unit.

6. To install, position lamp housing to grille opening

and install retaining nuts.

7. Connect ground wire to attaching point and install

retaining nut.

8. Connect wiring harness to lamp socket and check

operation of lamp.
Raise hood and disconnect harness connector from

lamp unit skirt-mounted
connector;
then
remove'lamp

unit connector from underside of skirt.

Working at the forward portion of the wheel well, re-

move the two lamp assembly retaining nuts and re-

move the lamp assembly and support from the

vehicle.

Route the lamp assembly lead wires through fender

cutout and position support over lead wires.

Position lamp unit studs through support and install

retaining nuts, making sure that the studs are

horizontal.

Connect harness to lamp unit skirt-mounted connec-

tor and close vehicle hood.

FENDER LAMP SERVICE (Fig. 11)

Chevrolet 16600 Models

1.
Disconnect parking lamp wiring from forward har-

ness connector.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-8

is inserted through radiator support opening.

Remove two screws retaining lamp assembly to

lower sheet metal.

Remove three screws retaining lamp assembly to

lender.

To replace lamp assembly, reverse removal proce-

dure and check operation of the unit.
is aligned with flat on pivot shaft. Install stop lock

bolt and torque bolt to 45-60 in, lbs. Make sure that

side-to-side panel alignment is not changed when in-

stalling and tightening the stop.

CAUTION: Do not exceed specified torque

when tightening stop lock bolt.

HEADLAMP PANEL REPLACEMENT-CORVETTE

Refer to Figure 13 for Panel Mounting details.

1.
Remove engine compartment hood as outlined in

Section 1.

2.
Actuate headlamp panel to the open position.

NOTE:
In the event headlamp motor is inop-

erative, manual positioning of the panel can be

accomplished by turning the knurled knob at in-

board end of motor. As an assist in manual

operation of panel, apply light hand pressure to

panel in desired direction of rotation.

3.
Remove positive lead from battery terminal.

4.
Remove headlamp bezel retaining screws and bezel.

5. Remove the sealed beam housing unit as an assem-

bly - disconnect sealed beam leads at harness con-

nector and remove connector from sealed beam

leads;
remove the housing-to-panel retaining screws

and remove housing unit and wiring from panel.

6. Remove motor from panel pivot shaft - see motor

removal procedure. Then remove the panel stop

from panel inboard pivot shaft, and disconnect switch

lead wires from panel, support-mounted motor

switch.

7. Remove the panel retaining bolt access hole plugs

from inside the panel then rotate panel as required

and remove the retaining bolts and slide supports

from ends of panel pivot shaft. Remove bearing, felt

seal, retainer and washer from inboard pivot shaft.

8. Remove panel from its location by alternately disen-

gaging pivots from their retaining slots and with-

drawing unit forward through opening in body (fig.

14).

9. Loosen alien screw in spacer and disassemble parts

from the panel outboard pivot shaft.

10.
Install washer, retainer, felt seal, bearing and

spacer, in that order, to panel outboard pivot shaft.

Do not tighten spacer on shaft at this time.

11.
Position panel in body opening and index panel pivot

shafts in retaining slots; then loosely install support

retaining bolts.

12.
Install washer, retainer, felt seal, bearing and sup-

port, in that order, to panel inboard pivot shaft, and

loosely install support retaining bolts. -

13.
Check side-to-side alignment of panel, making sure

that there is no panel-to-body contact; position

spacer snugly against bearing; then tighten spacer

seat screw to 30-50 in. lbs.

14.
Install stop on panel inboard shaft so that it rests

against bearing, being sure that index mark on stop
15.
Check and align panel to body as follows:

a. Tighten panel pivot support bolts snugly but still

allowing panel to" be moved by applying hand

pressure.

b.
Position panel to the closed position and align

with body so that all surfaces are flush.

c. With the panel in the closed position the outboard

access hole is aligned with the forward bolt head.

Tighten this bolt with the panel in the closed

position - access to bolt head can be obtained by

working through opening between the hood and

body.

d. Rotate panel to obtain access to each bolt head

and torque bolts to 100-140 in. lbs.

e. Connect switch lead wires to support-mounted

limit switch.

16.
Install seaLed beam housing unit and at the same time

position sealed beam lead wires through panel out-

board pivot shaft. Install housing unit retaining

screws and install lead wires in connector, making

sure to match colors between harness and connector.

17.
Install motor assembly - see motor replacement

procedure.

18.
Connect positive lead to battery terminal.

19.
Adjust headlamp panel as outlined under "Headlamp

Panel Travel Adjustment".

20.
Adjust headlamp aiming as outlined under "Headlamp

Adjustment".

21.
Install headlamp bezel and engine compartment

hood - refer to Section 1 for hood installation.

Fig.
14
- Headlamp Panel Removal (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-9

Fig.
15 - Headlamp Panel Actuating Motor Mounting (Corvette)'

HEADLAMP PANEL MOTOR-CORVETTE (Fig. 15)

Removal

1.
Raise hood and as a safety precaution install a bolt

through the hole in the hood support - secure bolt

with a nut.

2.
Remove positive lead from battery terminal.

3.
Disconnect motor lead wire and position it out of the

way.

4.
Turn the knurled knob at inboard end of motor until

the gear seems to turrj freely - turn the knob in one

direction until a definite drag is experienced, then

rotate knob approximately six complete turns in the

opposite direction.

NOTE:
The above step is necessary to produce

a no-load condition on the drive gear and to per-

mit separation of motor from the panel pivot

shaft.

5. Remove the retainer from groove in motor locating

stud then remove the motor-to-support retaining

screw and remove motor assembly from the vehicle.

Installation

1.
Rotate motor and headlamp panel as required to align

slot in motor with headlamp panel pivot shaft, and

install motor on shaft so that the bracket is aligned

with the locating stud.

NOTE:
It may be necessary to turn knurled

knob on end of motor to permit alignment of

motor with shaft.
Slide motor onto shaft until it seats against shaft

shoulder; then install retainer in groove on locating

stud.

Install motor-to-support retaining screw making

sure ground wire is installed between screw head and

bracket.

Connect motor lead wires, making sure that contacts

are clean and that connection is secure.

Connect positive lead battery terminal, remove bolt

from hood support, close hood and check operation of

headlamp panel.

HEADLAMP MOTOR REPLACEMENT-

CAMARO (Fig. 16)

1.
Disconnect battery ground cable and when working on

right headlamp unit, remove battery from vehicle to

gain access to housing retaining bolts.

2.
Remove bezel retaining screws and bezel.

3.
Remove headlamp cover retaining screws and cover

from door assembly.

4.
Manually open door assembly (push door toward cen-

ter of vehicle) and disconnect limit switch

connections.

5. Remove four screws retaining assembly to radiator

support (note location and number of shims, if any).

6. Rotate assembly toward center of vehicle until rear

of unit is exposed, then disconnect wiring connectors

at headlamp and motor assemblies.

7. Rotate assembly until headlamp is facing downward

and carefully remove the assembly from the vehicle

opening.

8. Remove nut attaching motor assembly to pivot arm.

9. Remove two nuts and bolts retaining motor assembly

to base plate and remove motor assembly.

CHEVROLET CHASSIS SERVICE MANUAL

ELECTRICAL-BODY AND CHASSIS 12-57

15.
Connect positive lead to battery terminal, lower hood

and test wiper and washer assembly for proper

operation.

WIPER TRANSMISSION

REMOVAL AND INSTALLATION

1.
Remove wiper block and arm assembly from trans-

mission.

2.
Remove glove box door and compartment assembly.

Refer to Section 1 for removal procedures.

3.
Remove three transmission-td-cowl retaining

screws.

4.
Remove wiper transmission retaining clip and re-

move transmission from crank arm. Then remove

transmission through the glove box opening.

5.
Reverse removal procedure to install wiper trans-

mission.

Fig.
94 - Wiper and Trans Installed

WIPER ASSEMBLY REPAIRS

The overhaul procedures for the wiper are broken down

into three major areas: The motor section, gear box

section and washer pump section. Each section may be

serviced independently of the other.

MOTOR SECTION

Disassembly

1.
Remove the two motor tie bolts.

2.
Remove the armature end-play adjusting screw (fig.

91).

3.
Strike the steel case lightly with a mallet to partiaUy

loosen it from the die casting housing and motor

field.

4.
Insert a tool through the armature adjusting screw

opening and push against the end of the armature

shaft to back off the case. This will retain the ar-

mature commutator in position between the brushes

until ready to separate the armature from the case.

5.
To separate armature from case while still retaining

the brush springs and brushes in place fashion a

spring similar to that shown in Figure 95 and insert

behind the brush leads as shown.
Fig.
95 - Retaining Armature Brushes

6. Pull the armature out of the case and remove the felt

washer, thrust plate, and rubber thrust disc from the

case assembly bearing as required.

7.
The field windings are pressed into the gear housing

and further disassembly is not recommended; how-

ever, the field leads may be unsoldered from the

brush holders to remove the case.

8. Clean and inspect all parts.

Inspect both the field and armature for damage

due to overheating such as unsoldered electrical

connections.

Check that brush leads are firmly attached both

to the brushes and their connections at the brush

holders.

Check brushes for wear. If brushes are worn to

within 3/16" of brush lead, or pigtail, they should be

replaced.

Check contacts of circuit breaker shown at top of

Figure 95. Clean as required or file lightly to re-

move irregularities.

Inspect all leads from the brush and circuit

breaker plate for worn insulation or tjreaks.

If it was determined by inspection that brush re-

placement was required, proceed as follows:

a. Remove retainer installed during disassembly and

remove brush springs.

b.
Place a hot soldering iron against*brush lead con-

nection on brush holders, remove old bushes, and

nection on brush holders, remove old brushes,

and install new brushes.

c. To reinstall brushes in holders, compress spring

within holder and hold fully compressed with a

thin instrument inserted through the slot in the

brush holder. Then push brush into holder with

lead upward to project through slot in holder, hold

CHEVROLET CHASSIS SERVICE MANUAL

SECTION 13

RADIATOR AND GRILLE

INDEX

Page Page

General Description 13-1 Repairs 13-4

Radiator and Shroud-All Vehicles (Except Corvette) . . . . 13-1 Installation 13-4

Removal 13-1 Grille Assembly - Chevy II 13-4

Installation 13-1 Removal . 13-4

Radiator and Fan Shroud - Corvette . . . . 13-1 Repairs 13-5

Fan Shroud Replacement 13-1 Installation . 13-5

Aluminum Radiator 13-1 Grille Assembly - Corvette 13-5

Copper Radiator . 13-1 Removal . . . . 13-5

Grille Assembly - Chevrolet 13-2 Installation ....*... 13-5

Removal 13-2 Grille Assembly - Caxnaro 13-5

Repairs 13-3 Removal 13-5

Installation 13-3 Repairs . 13-6

Grille Assembly - Chevelle 13-3 Installation . . 13-6

Removal 13-.Q

GENERAL DESCRIPTION

Radiator assemblies are attached by cap screws either the radiator and shroud are basically the same for each

to the radiator support or radiator shroud, depending on vehicle,

the engine installation of each vehicle. The Camaro fan

Shroud is mounted in two bottom slots and secured by one NOTE: Refer to the Fisher Body Service Man-

bolt at the top. Removal and installation procedures for ual for Body, Section IX for Sheet Metal, Section

14 for Bumpers, and Section 1A for Air Condi-

tioning information when required.

SERVICE OPERATIONS

RADIATOR
AND
SHROUD—ALL VEHICLES
NOTE: Reach upper two shroud bolts from top,

(EXCEPT CORVETTE)
between hood and radiator support. Reach lower

4 by reaching around front edge of open hood.

Removal

1.
Drain radiator. 4.- Remove shroud carefully (tilt rearward, then lift up

2.
Disconnect inlet and outlet radiator hoses, and Pow- to clear fan blades).

erglide cooler lines if vehicle is so equipped. 5. Reverse procedure to install, fill cooling system and

3.
Remove radiator and shroud attaching screws and lift check for leaks.

radiator and shroud out of vehicle.

Aluminum Radiator

Installation

NOTE:
Refer to Figures 1 through 5 for radi- Removal and Installation

ator fan and shroud assembled positions for each 1. Remove shroud as previously outlined.

vehicle. Reverse removal procedures, fill cool- 2. Disconnect lower raciiator hose at either end.

ing system and check for leaks. 3. Remove radiator upper mount bracket bolts and

bracket, then lift radiator from vehicle.

RADIATOR AND FAN SHROUD-CORVETTE 4. Reverse procedure to install.

Fan Shroud Replacement (Fig. 4) Copper Radiator

1.
Drain radiator and open hood. (Install a bolt in hole

of hood support bracket for safety purposes.) Removal and Installation

2.
Disconnect upper radiator hose and supply tank hose 1. Remove hood panel assembly after scribing bracket

at radiator connection. location.

3.
Remove shroud bolts. 2. Drain radiator and disconnect radiator hoses.

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS 26

LAMP USAGE (Cont'd.)
CANDLE

POWER

1

6

4

2

3

2

2

3

2

3

15

15
BULB

NUMBER

1445

212

67

1893

1816

194

1895

1816

257

1816

1003

93
Seat Separator-Compartment Lamp . . . . .

-Courtesy Lamp •

License Plate Lamp . .

Radio Dial Lamp

Chevrolet, Chevelle, Chevy n & Camaro

Corvette

Brake Alarm Lamp

. Chevrolet & Camaro . . .... . .

Chevelle & Chevy n . . . . .'. ;v . . . .

Corvette . . . . . . . .

Headlamp Mqtor Warning Lamp (Flashing) .

Clock Lamp (Corvette) .''> ....

Luggage Compartment Lamp. . ... . . . •

Underhood

FUSES AND CIRCUIT BREAKER

A circuit breaker in the light control switch protects

the headlamp circuit, thus eliminating one fuse. A

separate circuit breaker protects the power window,

seat and top circuits. On Corvettes the headlamp motor
circuit is also protected by a separate circuit breaker.

Where current load is too heavy, the circuit breaker

rapidly opens and closes, protecting the circuit until

the cause is found and eliminated.

louses located in the Fuse Panel under the instrument panel are:

Wiper (Chevrolet, Chevelle, and "F" Car) 3AF/AGC 20 Amp.

Back-up Lamp and Gauges. . . 3AG/AGC 10 Amp.

Heater - Air Conditioning 3AG/AGC 25 Amp.

Radio 3AG/AGC 10 Amp.

Radio - Wiper (Chevy II and Corvette) 3AG/AGC 20 Amp.

Instrument Lamps 3AG/AGC . 4 Amp.

Stop and Tail Lamps ........ t 3AG/AGC 20 Amp.

Clock, Lighter, Courtesy Lamps, and Hazard Warning 3AG/AGC 20 Amp.

In-Line Fuses:

Air Conditioning High Blower Speed Fuse located in wire running

from horn relay to A/C Relay

Comforton and Four Season SAE 30 Amp.

Universal & All Weather (Chevy H) SAE 20 Amp.

Fusible Links: ,

Pigtail lead at battery positive cable (except Corvette) 14 gage brown wire

Molded splice at Solenoid "Bat" terminal (Corvette only) 14 gage brown wire

Molded Splice Located at the horn relay 16 gage black wire

Molded splice in Voltage Regulator #3 terminal wire 20 gage orange wire

Molded splice in Ammeter circuit (Both sides of meter) 20 gage orange wire

CHEVROLET CHASSIS SERVICE MANUAL