light CHEVROLET CAMARO 1967 1.G Chassis Owner's Manual

FRONT SUSPENSION 3-12

2.
Remove forward nut, retainer and rubber bushing

from front end of strut rod.

3.
Remove two nuts from strut rod to lower control arm

bolts and remove bolts and washers.

4.
Withdraw strut rod from bracket.

5. Remove remaining rubber bushing, retainer, sleeve

and nut from strut rod.

6. Inspect rubber bushings for aging and replace if

necessary. *•

Installation

1.
Screw rear nu$ on forward end of rod and position it

approximately 3/4" from end of threads. Install

rear retainer, sleeve and bushing on rod so raised

pilot diameter faces forward.

2.
Insert strut rod in bracket so pilot diameter on bush-

ing pilots in hole in bracket. Install forward bushing

on sleeve so raised pilot diameter faces rear to

enter hole in bracket, then install forward retainer

and nut on rod.

3.
Attach strut rod to top of lower control arm with two

bolts,
washers and nuts.

4.
Lower vehicle to floor, check caster and camber

angles and adjust where necessary. Torque nuts as

shown in Specifications.

FRONT SPRING

Chevrolet

Removal

1.
With an open end wrench hold the shock absorber

upper stem from turning, and then remove the upper

stem retaining nut, retainer and rubber grommet.
I IVi" rVi"i

\>. j ii

>
I

5'4

s

WOOD
BLOCK
USED

WITH
CHEVROLET
ONLY

Fig.
19
- Spring Removal Tools - Chevrolet, Chevelle and Comoro

2.
With the car supported by the frame so that the con-

trol arms hang free, remove the wheel and tire as-

sembly (replace one wheel nut to retain the brake

drum),
shock absorber, stabilizer bar to lower con-

trol arm link, strut rod to lower control arm attach-

ing, nuts, bolts and lock washers and tie rod end.

3.
Scribe the position of the inner pivot camber adjust-

ing cam bolt and then remove the nut, lock washer

and outer cam.

4.
Install a steel bar (fabricated as shown in Figure 19)

through the shock abosrber mounting hole in the

lower control arm so that the notch seats over the

bottom spring coil and the bar extends inboard and

under the inner bushing. Fit a 5" wood block (See

Figure 19) between the bar and the bushing as shown

in Figure 20.

5.
With suitable jack or hoist, lift up slightly on the end

of the bar to remove the tension from the inner pivot

cam bolt, which can then be removed.

Fig.
18-Strut Rod

Pig. 20 - Front Spring Removal - Chevrolet

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION ,3-13

6. Carefully lower the inner end of the control arm.

Tension on the spring will be removed before the

spring can be removed from the vehicle.

7.
Remove the spring.

Installation

1.
With the suspension set up as in Step 2 of the disas-

sembly procedure, insert a block of wood between the

upper control arm and the spring tower to keep the

arm up out of the way.

2.
Set the spring in place on the crossmember after

checking on proper positioning necessary.

3.
Install the steel bar and wood block as shown in Fig-

ure 20 and lift the control arm up until the inner

pivot cam bolt can be installed. ,

4.
Install the outer cam and loosely install the lock

washer and nut

5.
Set the cam bolt on the mark scribed during the re-

moval procedure and hold in this position while tight-

ening the nut (See specifications at the end of this

book).

6. Replace the strut rod to lower control arm nuts,

bolts and lock washers, the stabilizer bar link, the

shock absorber, the tie rod end, and the wheel and

tire.

7.
Lower vehicle to floor and install the shock absorber

upper stem retaining nut retainer and grommet.

8. Check the camber adjustment.

Chevelle and Camaro

Removal

1.
With an open end wrench hold the shock absorber up-

per stem from turning, and then, remove the upper

stem retaining nut, retainer and rubber grommet.

2.
With the car supported by the frame so that the con-

trol arms hang free, remove the wheel and tire as-

sembly (replace one wheel nut to retain the brake

drum),
shock absorber, and stabilizer bar to lower

control arm link.
4.

5.
Fig.
21 - Front Spring Removal - Chevelle & Camaro

Place a steel bar (fabricated as shown in Figure 19)

through the shock absorber mounting hole in the

lower control arm so that the notch seats over the

bottom spring coil and the bar extends outboard be-

yond the end of the control arm and slightly toward

the front of the car.

With a suitable jack or hoist lift up slightly on the

end of the bar.

Remove the lower ball stud cotter pin and attaching

nut and remove the ball stud from the knuckle.

ALTERNATE METHOD

Fig.
22 - Removing or Installing Front Coil Spring - Corvette (Typical)

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-14

Fig.
23 - Installing Spring Compressor - Chevy II

CAUTION: Use extreme care not to damage

the seal during this operation.

6. Lower control arm as shown in Figure 21, until

spring can be removed.

Installation

1.
Properly position the spring on the arm and with the

steel bar in place, as shown in.Figure 21, lift the

arm up until the ball stud may be installed in the

knuckle. Install the nut and cotter pin.

NOTE:
^A block of wood between the upper con-

trol' arm and the frame will simplify this

operation.

2.
Replace the stabilizer bar link, shock absorber and

wheel and tire.

3.
Lower vehicle to floor and install the shock absorber

upper stem retaining nut, retainer and grommet.
Fig.
25 - Removing Spring and Seal Assembly - Chevy 11

ChevyiI

Removal

1.
Raise vehicle and remove wheel and tire.

2.
Support lower control arm with adjustable jackstand

and raise slightly from full rebound position.

3.
Remove shock absorber as outlined under Shock

Absorber -- Removal in this section (delete Step 1).

Fig.
24 - Compressing Front Spring - Chevy
Fig.
26 - Spring Seat - Exploded View - Chevy II

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-15

4.
Insert Spring Compressor J-
6874-
4-
5 with Adapters

J-6874-8-9 into upp^r spring tower so that lower

MU"
bolt fits into shock absorber mounting holes in

spring seat (fig. 23). Secure the two lower studs to

the spring seat with nuts.

5.
Fit the tool upper pilot to top of spring and compress

spring by tightening upper nut (fig. 24). Compress

spring until screw is bottomed out.

6. Remove lower spring seat retaining nuts, lift spring

and seat assembly from control arm and guide it

down and out through fender skirt (fig. 25).

Spring Seat Replacement (Fig. 26)

1.
Release spring tension and disconnect spring com-

pressor from spring seat.

2.
Install new spring seat to spring compressor.

Installation

1.
If spring is to be replaced, install new spring into

tool and compress spring until screw is bottomed

out.

NOTE: Spring coil ends must be against spring

stops in upper and lower seats.

2.
Lift spring and tool assembly into place and position

so that the upper spring stop is inboard.

NOTE: Locating tab on upper spring seat may

be flattened before reinstalling spring.

3.
Install lower spring seat to control arm and torque

nuts as shown in the Specifications.

4.
Loosen spring compressor until spring is properly

seated in upper spring tower and remove.

5.
Install shock abosrber as outlined under Shock Ab-

sorber—Installation in this section.

Corvette

Removal

1.
With car on suitable hoist or jack, (support vehicle

by frame so control arms may swing free) remove

wheel and tire assembly, stabilizer bar and shock

absorber. Loosen the lower ball joint to steering

knuckle nut, and the' two lower control arm cross

shaft bushing bolts.

2.
Place Tool J-6874-1 across top of sixth coil (ap-

prox.),
then loosely secure Tool J-6874-2 to the up-

per shoe, with attaching capscrews and lock washers.

The upper shoe "V" notch and lower shoe raised land

should contact spring.

3.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly.

4.
Position spacers under shock absorber mounting hole

and against bottom of lower control arm. Install

special bearing washer and Tool J-6874-5. Locate

bearing against spacer and large washer against

bearing. Feed screw up through large washer bear-

ing and spacer and thread into Tool J-6874 and

tighten snugly (fig. 22).

5.
Center shoe assembly on spring and tighten screw

until a very slight compression is placed on spring

(fig. '22). Then firmly tighten down the two cap-

screws securing the upper and lower shoes to lock

these shoes to spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower, then remove the

lower ball joint to steering knuckle nut (fig. 22).
NOTE: It may be necessary to assist the

spring out of the spring tower with a pry bar or

a similar tool.

7.
Disconnect the lower ball joint from the steering

knuckle and lower the control arm with the com-

pressed spring. Immediately release compression

on spring by backing off long screw. Release spring

and tool and withdraw spring.

CAUTION: The spring force under compres-

sion is very large. Exercise every safety pre-

caution when performing this operation to see

that individuals and materials subject to damage

are removed from the path of the spring when

the control arm is being lowered. Also, the

compressed spring
be relaxed immedi-

ately after lowering the control arm to reduce

the time of exposure to the large compressive

force.

Installation

1.
Position spring with closely coiled end up. Place

Tool J-6874-1 across the top of the sixth coil (ap-

prox.) then loosely secure Tool J-6874-2 to the

upper shoe with attaching capscrews and lock wash-

ers.
The upper shoe MV" notch and lower shoe

raised land should contact spring.

2.
Insert Tool J-6874 up through center of spring and

attach to upper and lower shoe assembly with bolt

and nut.

3.
Set spring in its seat on the lower control arm.

4.
Position spacers centrally under shock absorber

mounting hole and against bottom of lower control

arm. Install bearing, large washer and Tool

J-6874-5.
Locate bearing against spacer and large

washer against bearing. Feed the screw up through

large washer, bearing and spacer and thread into

yoke rod. Tighten snugly, but do not start to draw

down yet

5.
Center the shoe assembly on the spring and tighten

the lag screw until a very slight compression is

placed on spring, then firmly tighten down the two

capscrews securing the upper and lower shoes. This

will lock the shoes to the coil spring.

6. Turn head of screw until spring is compressed just

enough to clear the spring tower.

NOTE: It may be necessary to assist the

spring into the spring tower with a pry bar or

similar tool.

7.
Immediately install the lower ball joint into steering

knuckle and secure in place with attaching nut.

8. Release compression on spring and at the same time

use a drift to guide the coil spring into its proper

seat. End of coils must be 3/8" from coil stops in

spring seat.

9. Tighten the lower ball joint to steering knuckle nut

and lock with cotter key.

10.
Install shock absorber and stabilizer bar.

11.
Install wheel, tire and drum assembly.

12.
Remove car from hoist or jack stands.

13.
Tighten the two lower control cross shaft bushing

bolts to 45-55 lbs. ft. torque.

NOTE: If a suitable adjustable jack-stand is

CHEVROLET CHASSIS SERVICE MANUAL

FRONT SUSPENSION 3-21

Chevy II

Removal

1.
Support control arm on Tool J-7 574-4 and insert

Spacer J-9514 (fig. 34).

2,
Press bushing out with Tool J-9226 and Handle

J-7079-2 (fig. 34).

Installation

With Spacer J-9514 still in control arm, invert control

arm and press in new bushing with Tool, J-7474-2 and

Handle J-7079-2 until bushing is fully seated.

CAUTION: It should be noted that control arm

bushing diameters are unequal and bushing must

be pressed into position through larger diameter

only.

CROSS SHAFT AND/ON BUSHINGS

Corvette

Removal

1.
Remove bolt, lock washer and collar from each end

of cross shaft.

2.
Thread a 7/16 x 20 capscrew (furnished with Tool

J-5888) to the bottom of the threads in one end of the

cross shaft.

3.
Support control arm in an arbor press on Tool

J-5888-3,
as shown in Figure 35.

NOTE:
Be certain bushing flange does not

contact support.

4.
Press on cap screw until bushing is free of control

arm. Discard bushing.

5. Remove cap screw from cross shaft. Insert it in

other end of shaft. Invert control arm on support.

Again be certain bushing flange does not contact

support.

6. Press on cap screw until bushing is free of control

arm. Discard bushing.

Installation

1.
With cross shaft in control arm and Tool J-7052-1

in position, place control arm on Tool J-5888-3.

Hand start bushing into control arm and over end of

cross shaft.

NOTE:
The end of the shaft with the two bolt

holes should be toward front of control arm.

2.
Install Tool J-7052-5 over bushing. Be certain

three-piece spacer is not over-lapping bushing holes

in control arm.

3.
Press bushing into control arm until flange contacts

control arm (fig. 36).

4.
Invert arm in press and repeat the process on the

other bushing. After installation, cross shaft should

be free enough to be rotated by hand.

5. Install collar, lock washer and cap screw in each end

of cross shaft. Tighten to torque shown in Specifica-

tions after spring installation.
UPPER CONTROL ARM SPHERICAL JOINT

Chevrolet, Chevelle, Comoro and Corvette

Inspection

The upper spherical joint is checked for wear by

checking the torque required to rotate the ball stud in the

assembly. After performing the first four steps under

"Replacement" below, install a stud nut on the stud and

measure the torque required to turn the stud in the as-

sembly with a torque wrench. Specified torque for a new

joint is 9 lbs. ft. If torque readings are excessively

high or low, replace the ball joint. If excessive wear is

indicated in upper joint, both upper and lower joints

should be replaced.

NOTE:
This inspection does not necessitate

upper control arm removal.

Replacement

1.
Support the vehicle weight at the outer end of the

lower control arm.

2.
Remove the wheel and tire assembly.

3.
Remove cotter pin and nut from upper control arm

ball stud.

4.
Remove the stud from knuckle.

5. Cut off the ball joint rivets with a chisel.

6. Install new joint and retain in place with the special

nuts and bolts supplied.

7. Reassemble ball stud to the steering knuckle.

Chevy II

Inspection

The following on-the-vehicle check is to determine ball

joint wear.

NOTE:
The upper ball joint is a loose fit when

not connected to the steering knuckle. Wear may

be checked without disassembling the ball stud

by
using'
the following procedure:

1.
While vehicle weight is still on front wheels, insert

upper control arm support as shown in Figure 14.

2.
Raise vehicle and allow wheel and tire to hang free.

3.
Measure distance from tip of ball stud to top surface

of control arm.

4.
Place adjustable jackstand under tire and raise

slightly to take up ball joint looseness.

5. Repeat Step 3 and if the difference in measurements

exceeds 3/32", the joint is excessively worn and

should be replaced.

Replacement

1.
With vehicle weight still on front wheels, install

spacer between upper control arm and frame side

rail (fig. 15). Raise vehicle.

2.
Remove wheel and tire.

3.
Disconnect stabilizer link (if present) and strut rod

at lower control arm.

4.
Remove cotter pin and nut from upper ball joint stud.

5. Break ball stud loose. Drop lower control arm,

steering knuckle and brake assembly with an adjust-

able jackstand until upper control arm ball joint is

easily accessible.

6. Using a large chisel, cut off the three ball joint re-

taining plate rivet heads. It may be necessary to

drill out rivet heads before chiseling.

CHEVROLET CHASSIS SERVICE MANUAL

SECTION
4

REAR SUSPENSION
AND
DRIVE LINE

CONTENTS
OF
THIS SECTION

Page

Rear Suspension
4-1

Drive Line.
. 4-26

Rear Axle ......
4-26
Propeller Shaft
and
Universal Joints

Special Tools
4-37

4-43

REAR SUSPENSION

INDEX

General Description
4-1

Chevrolet
4-1

Chevelle
4-1

Chevy
n and
Camaro
. . . . . 4-2

Corvette
. . . . . . 4-3

Maintenance
and
Adjustments ...............
4-4

Riding Height Check (Chevrolet, Camaro,

Chevelle
and
Chevy
II) 4-5

Wheel Alignment (Corvette)
4-5

Wheel Bearing Adjustment (Corvette)
4-6

Component Parts Replacement (Chevrolet, Camaro,

Chevelle
and
Chevy
JJ) 4-7

Coil Spring
4-7

Chevrolet
4-7

Removal
4-7

Installation
4-7

Chevelle
4-8

Removal
4-8

4-8

Installation
.

Leaf Spring, Spring Seat Pads, Spring
Eye

Bushings
4-9

Chevy
H 4-9

Removal
4-9

Installation
4-9

Camaro
4-10

Removal
4-10

Installation
4-11

Shock Absorber
4-11

Chevrolet
and
Chevelle
. 4-11

Removal
4-11

Installation
. . 4-12

Chevy
II 4-12

Removal
4-12

Installation
4-rl2

Camaro
4-12

Removal
. 4-12

Installation
4-12

Control
Arm . . 4-12

Chevrolet Upper
4-12

Removal
. 4-12
Page

Bushing Replacement
. 4-13

Installation
4-14

Chevrolet Lower
4-14

Removal
4-14

Bushing Replacement
4-14

Installation
. 4-15

Chevelle Upper
and
Lower.
. 4-15

Removal
4-15

Bushing Replacement
4-15

Installation
4-17

Rear Suspension
Tie Rod
(Chevrolet)
. . .
......
. . . 4-17

Removal
4-17

Bushing Replacement
4-17

Installation
4-17

Component Parts Replacement (Corvette)
. . 4-17

Wheel Spindle
and
Support
4-17

Removal
4-17

Repairs
', . 4-17

Installation
4-18

Differential Carrier Support Bracket Replacement.
. 4-20

Shock Absorber
4-20

Removal
4-20

Installation
* .... 4-20

Strut
Rod and
Bracket
4-20

Removal
4-20

Repairs
4-21

Installation
4-21

Spring
4-21

Removal
4-21

Repairs
4-22

Installation
4-22

Torque Control
Arm 4-23

Removal
4-23

Repairs
. 4-23

Installation
4-24

Suspension Crossmember
4-24

Removal
4-24

Repairs—Isolation Mount
4-25

Installation
4-25

Stabilizer Shaft Replacement
4-25

GENERAL DESCRIPTION

CHEVROLET

The link type rear suspension (fig. 1) has two lower

control arms which maintain proper axle to frame re-

lationship and also take the acceleration, drive and

braking forces. A single upper control arm on light-

duty models (or two upper control arms on heavy-duty

models and all station wagons) limits axle rotation when

drive, acceleration or braking forces are applied. Lateral

movement of the axle is restricted by the axle-to-frame

tie rod. Two full coil springs and two direct, double
acting shock absorbers are provided for additional ride

control.

CHEVELLE

The rear suspension (fig. 2) is of the four-link design

utilizing axle mounted, full coil springs and direct,

double-acting shock absorbers.

Two rubber-bushed lower control arms, stretching

slightly outboard from axle-mounted brackets to frame

side member mounted brackets, maintain fore and aft

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-7

tioned vertically in the torque arm before ap-

plying pressure to the puller screw.

5.
Remove shim and bearing spacer from spindle

support.

6. Note size of shim used. If dial indicator reading

was more than
.008",
select a shim thinner by the

amount needed to bring end play within limits. If

dial indicator reading was less than
.001",
select a

shim thicker by the amount needed to bring end play

within limits.

NOTE: Shims are available in thicknesses from

.097"
to .148" in increments of
.003".

EXAMPLE: Bearing end play reading obtained

on dial indicator was
.011",
.003" over limit.

Bearing shim removed from spindle measures

.145".
New shim installed measures .139", .006"

smaller. End play is now decreased by .006" and

is
.005",
which is within the .001" to .008" limit.

7.
After determining shim thickness, install bearing

spacer and shim on spindle. Position spindle in

spindle support.

8. Press inner bearing race and roller assembly on

spindle as follows.

a. Position Tool J-4731 over spindle and against

bearing inner race.

b.
Position washer and spindle nut on spindle and

proceed to tighten nut until bearing is forced on

spindle sufficiently to allow spindle drive flange

to be installed (fig. 13). Remove spindle nut,

washer and Tool
J-4731.
Discard nut and use a

new one for final assembly.

9. Position drive flange over spindle, making sure

flange is aligned with spindle splines. Install washer
Fig.
13—Installing Drive Spindle to Support (Corvette)

and nut on spindle then tighten nut to specifications

and install cotter pin. If specified torque does not

permit cotter pin insertion, tighten nut to next flat.

10.
Seat spindle support outer seal in bore by using

screw driver, or other suitable tool, to press against

metal portion of seal.

11.
Install brake disc and caliper. Refer to Section 5

for details of brake disc and caliper installation.

12.
Install axle drive shaft, wheel and tire assembly,

adjust camber cam to original position and torque

all components to specifications.

COMPONENT PARTS REPLACEMENT

(Chevrolet, Chevelle, Chevy II and Camaro)

COIL SPRING

Chevrolet

Removal

To remove either or both rear coil springs proceed

as follows.

1.
Raise rear of vehicle and place jack stands under

frame. Support vehicle weight at rear, using either

a jack or post of twin-post hoist under axle.

2.
Remove both rear wheels from vehicle.

3.
With the car supported as in Step 1, so that the rear

springs are compressed by weight of vehicle; per-

form the following:

a. Disconnect both rear shock absorbers from the

anchor pin lower attachment.

b.
Loosen the upper control arm(s) rear pivot bolt

(do not remove the nut).

C. Loosen both the left and the right lower control

arm rear attachment (do not disconnect from axle

brackets).

d. Remove the rear suspension tie rod from the

stud on the axle tube.

4.
At the lower seat of both rear coil springs, slightly

loosen the nut on the bolt that retains the spring and

seat to the control arm. When the nut has been

backed off the maximum permissible, all threads of
the nut should still be engaged on the bolt.

CAUTION: Under ,no condition should the nut,

at this time, be removed from the bolt in the

seat of either spring.

5.
Slowly lower the support (jack or hoist post) that has

been in place under the rear axle, thereby allowing

the axle to swing down, carrying the springs out of

their upper seat and providing access for spring

removal.

6. Remove the lower seat attaching parts from each

spring, then remove the springs from the vehicle

(fig. 14).

Installation

1.
Position the springs in their upper seat so that end

of top coil is 3/8" ± 1/8" from end of stop. Install

the lower seat parts on the control arm, with the nut

finger tight on the spring retainer bolt.

NOTE: Omit the lock washer under the special

high carbon bolt, so that sufficient bolt thread

will be available to start the nut. The lock

washers will be installed later (in Step 4).

2.
By alternately raising the axle slightly and then

re-snugging the nut on each spring lower seat bolt,

move the axle upward until vehicle weight is fully

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-16

J-21474-5 J-21474-1

J-21058-8 /__* A r-j-21474-2

Fig.
37-Control Arm Bushing Removal (Chevelle)

However, the lower control arm bushings are of a dif-

ferent rubber material and are not interchangeable with

the upper bushings. Replacement procedures are in-

dicated below.

1,
Replace the control arm installed bushings as

follows:

a. Position control arm in a vise, or other suitable

holding device, so that clamping action is against

closed section of control arm.

b.
Place Puller Screw J-21058-15 through Puller

Adapter J-21474-2. Position puller screw through

small end of bushing then install Receiver

J-21474-5. Thrust Bearing and Nut J-21058-8

(in that order) onto puller screw. Install Spacer

J-21474-1 between sides of control arm and over

bushing so that spacer follows contour of bushing.

Refer to Figure 37 for installation of removal

tools.

c. Turn Nut J-21058-8 to withdraw bushing, making

sure Remover Adapter J-21474-2 is centered

and will clear hole in control arm.

d. Disassemble puller tools and position Installer

Adapter J-21474-2 on flanged end of new bushing.

Position Puller Screw J-21058-15 through in-

staller adapter and bushing; then place assembly

through hole in control arm.

NOTE:
Bushings are installed in one direction

only - flanged end of bushing seats against rolled

cutout side of control arm.

e. Install Receiver J-21474-5, Thrust Bearing, and

J-21058-15 J-21474-1
Fig.
39—Carrier Mounted Suspension Bushing

Removal (Light-Duty) (Chevelle)

Nut J-21058-8 (in that order) onto puller screw.

Install Spacer J-21474-1 between sides of control

arm and, over bushing so that spacer follows

contour of bushing. Refer to Figure 38 for in-

stalled view of tools.

f. Turn Iftit J-21058-8 to pull bushing into control

arm. Check position of bushing when installing

to make sure bushing is properly aligned. Seat

flanged end of bushing firmly against control

arm, but do not apply unnecessary force after

bushing is seated - to do so will distort control

arm.

2.
Replace the carrier mounted, upper control arm rear

bushing using the following procedure.

Light-Duty Carrier

a. Position Puller Adapter J-21474-2 on Puller

Screw J-21058-15 then place puller screw through

small end of bushing.

b.
Install Receiver J-21830-4, Bridge J-21830-7,

Thrust Bearing, and Nut J-21058-8 (in that order)

onto puller screw. Refer to Figure 39 for in-

stalled view of tools.

Fig.
38—Control Arm Bushing Installation (Chevelle)
Fag.
40—Carrier Mounted Suspension Bushing

Installation (Light-Duty) (Chevelle)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-21

Fig.
54—Marking Camber Cam and Bracket (Corvette)

bracket, so they may be reassembled in same loca-

tion (fig. 54).

5.
Loosen camber bolt and nut. Remove four bolts se-

curing strut rod bracket to carrier and lower

bracket.

6. Remove cam bolt nut and cam and bolt assembly.

Pull strut down out of bracket and remove bushing

caps.

7.
Inspect strut rod bushings for wear and replace

where necessary. Replace strut rod if it is bent or

damaged in any way.

Repairs

1.
With strut rod bushing centered over Tool J-7877-2

and with strut rod supported horizontally, press or

drive bushing from rod, using Tools J-7877-i and

J-7079-2 as shown in Figure 55.

2.
With strut rod end centered over Tool J-7877-2 and

rod supported horizontally, press or drive bushing

into arm using Tools J-7877-3 and J-7079-2 as

shown in Figure 55. Tool J-7877-3 should bottom

on strut rod when bushing is fully installed.

Installation

1.
Place bushing caps over inboard bushing and slide

rod into bracket. Install cam and bolt assembly and

adjust cam to line up with mark on bracket. Tighten

nut but do not torque at this point.
SPRING
LINK BOLT

SPRING
CUSHION

SPRING

CUSHION
CENTER

CLAMP

PLATE

J-7877-3

J-7877-1

STRUT ROD 11 s* ^#3 STRUT ROD

BUSHING
Fig.
56—Spring Mounting (Corvette)

2.
Raise bracket and assemble to carrier lower mount-

ing surface. Torque bolts to specifications.

3.
Raise outboard end of strut rod into spindle support

fork and insert strut rod shaft into fork so that flat

on shaft lines up with corresponding flat in spindle

fork. Install retaining nut, but do not torque.

4.
Place shock absorber lower eye and bushing over

strut shaft, install washer and nut and torque to

specifications.

5.
Lower vehicle to floor and torque camber cam nut

and strut rod shaft nut to specifications. Then in-

stall cotter pin through rod bolt.

6. Check rear wheel camber and adjust where

necessary.

SPRING (Fig. 56)

Removal

1.
Raise rear of vehicle and support on frame slightly

forward of torque control arm pivot points. Remove

wheels and tires.

Fig.
55—Strut Rod Bushing Replacement
Fig.
57—Chain Installation (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

REAR SUSPENSION AND DRIVE LINE 4-24

4

i*
5

Fig.
65—Removing Bushings (Corvette)

4.
Lightly oil new bushing diameters (not rubber por-

tion) and start bushings squarely in arm.

5. Install Tool J-7055-1 as shown in Figure 66 and

press bushings into place.

6. When bushings are fully installed, place special

plate over flared portion of new bushing retainer

and insert retainer into bushing.

7. Out of 5/8" thick steel plate 1-1/2" wide make flar-

ing tool support to the dimensions shown in Figure

67 and drill clearance holes as shown for 2
—
1/2"

bolts.

8. Place fabricated back-up plate on flared end of bush-

ing retainer and assembly Tool J-8111-23 to plate

with 2-1/2" bolts 5" long. Make sure threaded hole

in J-8111-23 is centered over unflared end of bushing

retainer and that chambered retainer plate is cen-

tered over retainer tube.

9. Lightly oil pointed end of J-8880-5 screw and thread

into J-
8111-23
until pointed "end contacts bushing

retainer. Continue threading J-8111-23 until retainer

is flared (fig. 68).

Installation

1.
Place torque arm in frame opening.

2.
Place toe-in shims in original position on both sides

of torque arm, install pivot bolt and tighten but do

not torque at this point.
Fig.
67—Flaring Tool Back-Up Plate (Corvette)

3.
Raise axle drive shaft into position and install to

drive flange. Torque bolts to specifications.

4.
Raise strut rod into position and insert strut rod

shaft so that flat lines up with flat in spindle sup-

port fork. Install nut and torque to specifications.

5. Install shock absorber lower eye and tighten nut

to specifications.

6. Connect spring end as outlined under Spring-

Bistallation, Steps 3-6'.

NOTE:
If vehicle is so equipped, connect sta-

bilizer shaft to torque arm - refer to "Sta-

bilizer Shaft Replacement".

7. Install brake disc and caliper, wheel and tire and

lower vehicle. Tighten torque arm pivot bolt. Bleed

brakes as outlined in Section 5-Brakes.

SUSPENSION CROSSMEMBER

Removal

1.
Disconnect and remove spring as outlined under

Spring-Removal.

2.
Remove differential carrier assembly as outlined

under Differential Carrier-Removal in this section.

3.
Support crossmember, remove bolts securing

crossmember isolation mounts to frame and lower

crossmember (fig. 69).

Fig.
66—Installing Bushings (Corvette)
Fig.
68—Flaring Retainer (Corvette)

CHEVROLET CHASSIS SERVICE MANUAL