ABS CHEVROLET CAMARO 1967 1.G Chassis Manual PDF

ACCESSORIES 15-11

12 VOLTS D.C.
ELECTRIC BRAKE

RELEASE

IGNITION

SWITCH

ENGINE

VACUUM

TRANSDUCER

Fig.
11 - Vacuum and Electrical Diagram

AUTOMATIC LEVEL CONTROL

INDEX

Page

General Description . . 15-11

System Checks and Adjustments 15-13

Service Operation . 15-15

GENERAL DESCRIPTION

A pneumatic level control system that automatically

maintains correct rear trim height of a car under varying

load conditions, the optional automatic level control is

used only in conjunction with the Superlift Shock Absorber

option.

The Superlift Shock Absorber option alone, consists of

the two shock absorbers with pressure lines to a "Tee"

where a ill valve is located, the shocks are inflated

with (or deflated of) compressed air (at any gas station)

to obtain the vehicle level desired with any given load

change.

The automatic leveling system is added to the Superlift

Shock Absorbers and supplies its own compressed air.

The system (fig. 13) consists of a vacuum operated air

compressor with pressure regulator,
and
integral storage

tank, vacuum line to engine, air intake filter, air lines,

and a height control valve.

The COMPRESSOR is a two-stage, vacuum actuated

type, requiring no lubrication. Vacuum supply is taken

from engine carburetor base. High pressure air is
supplied to the reservoir tank by the second stage of

the two-stage compressor. The first stage intake stroke

draws air at atmospheric pressure through a oneway

check valve located in the end of the first stage housing

under the first ^tagei housing cover. On the first stage

compression stroke, the intake valve is closed and the

oneway check valve in the second stage end of the piston

is opened. This allows the air from the first stage

cylinder to flow through the hollow piston into the second

stage cylinder for jhigh pressure compression. The

second stage compression stroke closes the check valve

in the piston and opeijis the check valve in the end of the

second stage housing.

The intake and compression strokes are controlled by a

sliding distributor valive that is actuated through an arm

that is tripped by the piston as it nears the end of each

stroke. Each time the arm actuates the distributor

valve, a different set of holes are covered in the first

stage housing. The distributor valve controls the flow of

intake manifold vacuum and air under atmospheric pres-

CHEVROLET CHASSIS SERVICE MANUAL

ACCESSORIES 15-12

VACUUM

(WIT

P

VACUUM Llh

, AIR SUPPt

LINES

t

SUPERLIFT F

SHOCK ABSO
OPERATED AIR COMPRESSOR

H STORAGE TANK AND

RESSURE REGULATORJV

\A

4E FROM ENG«NE^"^
/ \-HEIGHT CONTROL

•^-Z n VALVE (WITH TIME

^* DELAY MECHANISM)

EAR II

RBERS

Fig.
12 - Automatic Level Control Schematic

sure,
alternatley to opposite sides of the compressor

diaphragm.

As the compressor cycles, the reservoir air pressure

gradually increases causing a back pressure on the sec-

ond stage piston until it equals the push of pressure

against the diaphragm- At this point, a balanced condi-

tion is reached and the unit stops operating. After res-

ervoir pressure drops due to system air usage, the com-

pressor again begins to cycle and replenish the

reservoir.

Pressure balance will depend upon the prevailing mani-

fold vacuum and atmospheric pressure. Both are af-

fected by altitude above or below sea level. Balance

pressure will vary from approximately 150 to 275 psi.

NOTE: After completion of work on this sys-

tem or when servicing other parts of the car and

the system is deflated, inflate the reservoir to

140 psi or maximum pressure available through

the compressor service valve.

The PRESSURE REGULATOR VALVE is preset and

limits the reservoir outlet pressure to approximately 125

psi to avoid damage to the height control valve and Super-

lift shocks.

The HEIGHT CONTROL VALVE, which is mounted on

the frame, senses rear car height through a link attached

to the right rear upper control arm. When load is added

to the car, the overtravel lever is forced up causing an

internal lever to open the intake valve, when this valve

is open high pressure air is admitted to the Superlift

shocks. As the car raises to level, the intake valve shuts

off.

When load is removed from the car, the overtravel

lever is forced down causing the internal arm to open the

exhaust valve. As the car lowers to the level position,

the exhaust valve shuts off.

A four to eighteen second time delay mechanism, which

is built into the height control valve, prevents air trans-

fer due to normal ride movements. The overtravel

lever, which pivots around the control valve shaft, rides

off the flat side of the control valve shaft and does not

have time to. react to the rapid changes or normal ride

motions.
During changes due to loading, the time delay mecha-

nism will allow the overtravel shaft to open either the in-

take or exhaust' valve as required, since this is not a

rapid movement.

The SUPERLIFT shock absorber is essentially a con-

ventional hydraulic unit with a. pliable nylon reinforced

neoprene boot acting as an air chamber.

The unit will extend when inflated and retract when de-

flated by the control valve.

An eight to fifteen psi air pressure is maintained in the

Superlift at all times to minimize boot friction- This is

accomplished by a check valve in the exhaust fitting on

the control valve. Neither shock absorber function nor

conventional ride motions thru rear coil springs is im-

paired in the event of accidental air pressure loss. .

A combination of steel tubing and reinforced rubber

hose is used for air lines throughout the system.

-SUPERLIFT

PORT

STATION WAGON

& SEDAN

INTAKE

PORT
HAUST

PORT

Fig. 13 - Height Control Valve

AIR CHAMBER
BOOT

AIR DOME AIR PISTON

Fig. 14- Superlift Absorber

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS
2

RIDING HEIGHT MEASUREMENT*

Chevrolet
All Biscayne
and Bel Air 2 and 4
Doors,

All Impala
and
Caprice
4
Doors
and

All Station Wagons
. . . .

All Impala
and
Caprice
2
Doors
. . . . .
5-1/8"
± 1/2"

5-3/8"
± 1/2"

Chevelle
All Sedans

SS Coupe
and
Convertible

El Camino
and
Station W*
1-3/811
± 1/2"

1-1/8"
± 1/2"

..
2" ± 1/2"

Chevy
u
All
4 and 6
Cylinder Standard
2 and 4
Doors,

All Station Wagons,
and 6
Cylinder Nova
4
Door

All
8
Cylinder Standard
2 and 4
Doors,
All

Nova
2
Doors
and 8
Cylinder Nova
4
Door
. . .
3-3/4'

3-1/4'
±
1/2'

±
1/2'

Corvette
With
327 or 427
Engine
. . . .

327 Engine with
A/C or 427
Engine with
A/C,
P.S.,.and
P.B

Convertible with
327
Engine, Hardtop,
A/C, P.S., P.B., and
Powerglide

427 Engine with Optional Suspension
.
2-1/2"

.
2"

1-1/2"

1-1/2"
±
1/2"

±1/2"

±
1/2"

±
1/2"

Camaro
With
230
Engine
..... . . .

With
250
Engine
.... ...

With
283 - 327 and
350 Engine
2-3/4"

2-7/8"

2-5/8"
± 1/2"

± 1/2"

± 1/2"

•Must be within 1/2" from side to side

BOLT TORQUES

TORQUES

Spherical Joint

Upper Stud
Nut

Lower Stud
Nut

Stud
to
Control

Arm Nuts (Service)

Lower Forging
Nut

Steering
Arm
Attaching Nuts

Shock Absorber

Upper Shaft
Nut

Lower Attachment

Bracket
to
Spring Tower

Stabilizer
Bar

Frame Bracket Bolts

Link Nuts

Strut
Rod

Rod
to Arm Nut

Adjustment
Nut

Front Spring

Spring Seat
to
Control

Arm Nuts

Lower Control
Arm

Inner Pivot Nuts

Upper Control Arm

Attaching Nuts

Collar Bolts

Brake Anchor Pin

Drum Brakes

Brake Anchor Bolt

Disk Brakes

Lower Control Arm

Cross Shaft Bolts

Front

Rear .

Wheel Stud Nuts
Chevrolet

50 ft. lbs.

80 ft lbs.

25 ft. lbs.

40 ft. lbs.

50 ft. lbs.

8 ft. lbs.

15 ft. lbs.

—

15 ft lbs.

8 ft. lbs.

70 ft lbs.

80 ft lbs.

115 ft lbs.

75 ft lbs.

45 ft lbs.

130 ft lbs.

—

65 ft lbs.
Chevelle

50 ft lbs.

80 ft lbs.

25 ft. lbs.

—

85 ft lbs.

8 ft lbs.

20 ft lbs.

—

15 ft lbs.

8 ft lbs.

—

80 ft lbs.

50 ft. lbs.

45 ft. lbs.

130 ft lbs.

—

65 ft lbs.
Chevy H

45 ft lbs.

45 ft lbs.

25 ft lbs.

—

65 ft. lbs.

8 ft lbs.

9 ft lbs.

9 ft. lbs.

9 ft. lbs.

10 ft. lbs.

45 ft lbs.

80 ft lbs.

30 ft lbs.

65 ft lbs.

50 ft. lbs.

50 ft lbs.

130 ft lbs.

_

—

65 ft lbs.
Corvette

45 ft lbs.

20 ft lbs.

20 ft lbs.

—

20 ft lbs.

10 ft lbs.

—

10 ft lbs.

10 ft. lbs.

—

95 ft lbs.

35 ft lbs.

40 ft lbs.

75 ft lbs..

70 ft lbs.

135 ft lbs.

75 ft lbs.
Camaro

50 ft lbs.

65 ft lbs.

25 ft lbs.

—

85 ft lbs.

8 ft lbs.

20 ft lbs.

.
—

15 ft. lbs.

8 ft._lbs.

_

85 ft lbs.

50 ft lbs.

45 ft lbs.

130 ft lbs.

_

—

65 ft lbs.

CHEVROLET CHASSIS SERVICE MANUAL

SPECIFICATIONS 3

REAR SUSPENSION

REAR AXLE

SECTION 4

CHEVROLET, CAMARO, CHEVELLE AND CHEVY II

Gear Backlash . . (.005"-.008" preferred) .003"-.010"

Pinion Bearing Preload (in. lbs.)

New 20-30

Used . 5-15

Lubricant Capacity

Large Carrier 4-1/2 pints

Small Carrier 3-1/2 pints

Bolt Torques (Ft Lbs.)

Carrier Cover 20

Ring Gear 50

Differential Bearing Caps 55

Filler Plug . . 20

Differential Pinion Lock . 20
CORVETTE

Gear Backlash . (.
005"-,
008"
preferred). . .003"-.010"

Pinion Bearing Preload (in. lbs.)

New 20-25

Used 5-15

Lubricant Capacity 3-3/4 pints

Bolt Torques (Ft Lbs.)

Carrier Cover 50

Ring Gear . 50

Differential Bearing Caps . 55

Filler Plug 20

Differential Pinion Lock 20

Type

Heavy Duty Axle

Light Duty Axle

Bolt Torque (ft lbs.)

Spring Retainer

Control Arm Upper

Front Bracket

Upper Bushings

Lower Bushings

Shock Absorber

Upper Nut

Upper Bracket

Lower Nut

Spring Shackle

Front

Rear

Tie Rod

Attaching Nuts

Stud to Axle Bracket

Universal Joint

Companion Flange

Transmission Yoke

Wheel Stud Nuts

Axle Drive Shaft

to Spindle

to Yoke
Chevrolet

4-Link
System

3-Link
System

25

55

70

110

15

65

65

110

15

65
Chevelle

4-Link
System

80

80

12

65

15

65
Chevy H

Semi-Elliptic

Tapered

Single Leaf

40

10

10

50

55

50

15

65
Camaro*

Semi-Elliptic

Tapered

Single Leaf

50

8

10

45

100

50

15

65
Corvette

Independent

Three-Link

System

65

50

35

15

15

75

75

15

@ Station Wagon all
4-Link
System

CHEVROLET a
SfRVK