lock CHEVROLET CAMARO 1994 4.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine Features and Controls
I‘
Remote Hatch Release (Option)
Press the switch in your glove box to
unlock the
hatch from inside your vehicle.
If you have an automatic transmission,
your shift lever
must be in “P’ (Park) or
“N” (Neutral) to use the switch. If you
have a manual transmission and the
ignition switch is in “Run”, you must set
the parking brake before you can use the
switch.
The switch only works when the ignition
switch
is in “Run” or “Acc”, or when
RAP is present. (See “Retained
Accessory Power”
in the Index.)
NOTICE:
If you put things in the hatchback
area, be sure they won’t break the
glass when you close
it. Never slam
the hatch down. You could break the
glass or damage the defogger grid (if
equipped),
... 52

Downloaded from www.Manualslib.com manuals search engine Theft
Vehicle theft is big business, especially in
some cities. Although your Chevrolet has
a number of theft-deterrent features, we
know that nothing we put on it can make
it impossible to steal. However, there
are
ways you can help.
Key in the ignition: If you walk away
from your vehicle with the keys inside,
it’s an easy target for joy riders or
professional thieves
- so don’t do it.
When you park your Chevrolet and open
the driver’s door, you’ll hear a tone
reminding you to remove your key from
the ignition and take it with
you. Always
do this. Your steering wheel will be
locked, and
so will your ignition. If you
have an automatic transmission, taking
your key out also locks your transmission.
And remember
to lock the doors.
Parking at Night: Park in a lighted spot,
close all windows and lock your vehicle.
Remember
to keep your valuables out of
sight. Put them in a storage area, or take
them with you.
Parking Lots: If you park in a lot where
Someone will be watching your vehicle,
it’s best to lock it up and take your keys.
But what if you have to leave your
ignition key? What if you have to leave
something valuable in your vehicle?
0 Put your valuables in a storage area,
like your glove box.
0 Lock the glove box.
0 Lock all the doors except the driver’s.
Then take the door key with you.
PASS-Key@ZZ
Your vehicle is equipped with the
PASS-Key@II (Personalized Automotive
Security System) theft-deterrent system.
PASS-Key@II is a passive theft-deterrent
system. This means you don’t have
to do
anything different to arm or disarm the
system. It works when you insert
or
remove the key from the ignition.
PASS-Key@II uses a resistor pellet in
the ignition key that matches a decoder
in your vehicle.
53.

Downloaded from www.Manualslib.com manuals search engine Features and Controls
When the PASS-KeyW system senses
that someone is using the wrong key, it
shuts down the vehicle’s starter and fuel
systems. For about three minutes,
the
starter won’t work and fuel won’t go to
the engine. If someone tries to start your
vehicle again or uses another
key during
this time, the vehicle will not start. This
discourages someone from randomly
trying different keys with different
resistor pellets
in an attempt to make a
match.
SECURITY
~
The ignition key must be clean and dry
before it’s inserted
in the ignition or the
engine may not start. If the engine does
not start and the
“SECURITY” light stays
on when you
try to start the vehicle, the
key may be dirty or wet. Turn the
ignition off.
Clean and dry the key. Wait about three
minutes and try again. The security light
will remain on during this time. If the
starter still won’t work, and the key
appears to be clean and dry, wait about
three minutes and try another ignition key.
At this time, you may also want to check
the fuses (see “Fuses and Circuit
Breakers”
in the Index). If the starter
won’t work with the other key, your
vehicle needs service.
If your vehicle does start,
the first ignition key may be
faulty. See your Chevrolet dealer or a
locksmith who can service the
PASS-KeyaII.
If you accidentally use a key that has a
damaged or missing resistor pellet, the
starter won’t work and the security light
will flash. But you don’t have to wait
three minutes before trying another
ignition key.
See your Chevrolet dealer or a locksmith
who can service the PASS-Key@II to have
a new key made.
If you’re ever driving and the
“SECURITY” light comes on and stays
on, you will be able to restart your engine
if you turn it off. Your PASS-Key@II
system, however, is not working properly
and must be serviced by your Chevrolet
dealer. Your vehicle is not protected by
the PASS-KeyW system.
If you lose or damage a PASS-Key@II
ignition key, see your Chevrolet
dealer or a locksmith who can service
PASS-Key@II
to have a new key made.
In an emergency, call the Chevrolet
Roadside Assistance Program on
1 -800-CHEV-USA (1 -800-243-8872).
... 54

Downloaded from www.Manualslib.com manuals search engine New Vehicle
“Break-In”
NOTICE:
Your modern Chevrolet doesn’t need
an elaborate “break-in.” But it will
perform better
in the long run if you
follow these guidelines:
Keep your speed at
55 mph (88
km/h) or less for the first 500
miles (804 km).
Don’t drive at any one speed
-
fast or slow - for the first 500
miles (804 km). Don’t make
full-throttle starts.
Avoid making hard stops for the
first
200 miles (322 km) or so.
During this time your new brake
linings aren’t yet broken
in. Hard
stops with new linings can mean
premature wear and earlier
replacement. Follow this
“breaking-in” guideline every
time
you get new brake linings.
D
I Ignition Switch
Vith the ignition key in the ignition
witch,
you can turn the switch to five
lositions:
KC (A): Position in which you can
lperate your electrical power accessories.
’ress
in the ignition switch as you turn
?e top
of it toward you.
,OCK (B): The only position in which
ou can remove the key. This locks your
teering wheel, ignition and automatic
7ansmission.
f you have an automatic transmission, the
znition switch can’t be turned to
LOCK” unless the shift lever is
in the
“P” (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories.
Use this position if your
vehicle must be pushed or towed.
A
warning tone will sound if you open the
driver’s door when the ignition
is in “Off’
and the key is
in the ignition.
Run (D): Position to which the switch
returns after
you start your engine and
release the switch. The switch stays
in the
“Run” position when the engine is
running.
But even when the engine is not
running,
you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “ACC” and “Run’’ allow
you to
operate your electrical accessories, such
as the radio and ventilation fan.
55. .

Downloaded from www.Manualslib.com manuals search engine Features and Controls
Key Release Button: If you have a
manual transmission, your ignition lock
has a key release button.
You must press
the button before
you can take your key
out
of the ignition lock.
NOTICE:
If your key seems stuck in “Lock”
and you can’t turn
it, be sure it is all
the way in. If it is, then turn the steer-
ing wheel left and right while you
turn the key hard. But turn the key
only with your hand. Using
a tool to
force it could break the key or the
ignition switch. If none
of this works,
then
your vehicle needs service.
Retained Accessory Power (RAP)
If you have power door locks, your
vehicle has a feature called Retained
Accessory Power (RAP). With RAP your
power door locks, electric mirrors, power
windows, audio system and remote hatch
release
will continue to work up to 10
minutes after the ignition key is turned to
“Off’ and neither door
is opened.
If
a door is opened, the audio system and
power windows will shut off. The power
door locks, electric mirrors and remote
hatch release
will work until you shut the
door. Once you have shut the door, these
accessories
will continue to work for
approximately
35 seconds. After this
time you will not be able to use these
accessories until the next time you open
a door or
turn on the ignition.
... 56

Downloaded from www.Manualslib.com manuals search engine Engine Coolant Heater
(Engine Block Heater)
(OPTION)
In very cold weather, 0°F (- 1 8 "Cj or
colder, the engine coolant heater can help.
You'll get easier starting and better fuel
economy during engine warm-up.
Usually, the coolant heater should be
plugged
in a minimum of four hours prior
to starting your vehicle.
To use the coolant heater:
1. Turn off the engine.
2. Open the hood and unwrap the
electrical cord.
3. Plug it into a normal, grounded
110-volt outlet.
NOTICE:
After you've used the coolant heater,
be sure
to store the cord as it was
before, to keep
it away from moving
engine parts.
If you don't, it could be
damaged.
How long should you keep the coolant
heater plugged in? The answer depends
on the weather, the kind
of oil you have,
and some other things. Instead
of trying to
list everything here, we ask that
you
contact a Chevrolet dealer in the area
where you'll be parking your vehicle. The
dealer can give
you the best advice for
that particular area.
59. .

Downloaded from www.Manualslib.com manuals search engine Features and Controls
Automatic Transmission
rhere are several different positions for
Tour shift lever.
B P (Park)
rhis locks your rear wheels. It’s the best
losition to use when you start your
:ngine because your vehicle can’t move
:asily. Ensure the shift
lever
is fully in “P’
:Park) range before starting the engine.
Your Chevrolet has a brake-transmission
shift interlock.
You have to fully apuly
your regular brakes before
you can shift
From
“P’ (Park) when the ignition key is
In the “Run” position. If you cannot shift
]ut of
“P’ (Park), ease pressure on the
shift lever
- push the shift lever all the
way into
“P’ (Park) and also release the
shift lever button on floor shift console
models as you maintain brake application.
I‘hen move the shift lever into the gear
you wish. (Press the shift lever button
before moving the shift lever on floor
shift console models.) See “Shifting out
Df “P’ (Park)” in this part.
. ..60

Downloaded from www.Manualslib.com manuals search engine Features and Controls
a
a
0
0
0
2 (Second Gear) - Press the clutch
pedal as you let up on the accelerator
pedal and shift into
“2.” Then, slowly
let up on the clutch pedal as you
press the accelerator pedal.
3,4,5 and 6 (Third, Fourth, Fifth
and Sixth Gears)
- Shift into “3,”
“4,” “5” and “6” the same way you do
for
“2.” Slowly let up on the clutch
pedal
as you press the accelerator
pedal.
To Stop - Let up on the accelerator
pedal and press the brake pedal. Just
before the vehicle stops, press
the
clutch pedal and the brake pedal, and
shift to “Neutral.”
Neutral - Use this position when
you start or idle your engine.
R (Reverse) - To back up, press
down the clutch pedal and shift into
“R.” Let
up on the clutch pedal slowly
while pressing the accelerator pedal.
If you shift from
“6” into “R,” the
shift lever must be first placed in the
“Neutral” position centered between
“2” and “3” prior to shifting into “R.”
Your six-speed manual transmission has a
feature that allows you to safely shift into
“R’ (Reverse) while the vehicle is rolling
(at less than
5 mph). You will be
“locked-out”
if you try to shift into “R’
(Reverse) while your vehicle is moving
faster than
5 mph.
If
you have turned your ignition off and
wish to park your vehicle
in Reverse, you
will have to move the shift lever quickly
to the right, “crashing” through the high
load spring and then into gear.
SKIP SHIFT
Skip Shift Light (5.7L LT1 Engine)
When this light comes on, you can only
shift from “1” (First) to
“4” (Fourth) gear
instead of
“1” (First) to “2” (Second)
gear. This helps you
to get the best
possible fuel economy.
This light will come on under these
conditions:
0 The engine coolant temperature is
0 You are going 15-20 mph
0 You are at 35% throttle or less.
greater than
170°F
(77”C),
(24-32 km/h), and
... 64

Downloaded from www.Manualslib.com manuals search engine Features and Controls
1. Hold the brake pedal down with your
right foot and set the parking brake.
2. Move the shift lever into “P’ (Park)
position like this:
Hold in the button on the lever,
and push the lever all the
way
toward the front of your vehicle.
3. Move the ignition key to “LOCK.”
4. Remove the key and take it with you.
If you can walk away from your
vehicle with
the ignition key in your
hand, your vehicle is in “P” (Park).
Leaving Your Vehicle with the
Engine Running
(AUTOMATIC TRANSMISSION)
If you have to leave your vehicle with the
engine running, be sure your vehicle is
in
“P’ (Park) and your parking brake is
firmly set before you leave it. After
you’ve moved the shift lever into the
“P’
(Park) position, hold the regular brake
pedal down. Then, see
if you can move
the shift lever away from “P” (Park)
without first pushing the button. If you can,
it means
that the shift lever wasn’t
fully locked into “P’ (Park).
Torque f Ock (AUTOMATIC
TRANS#lSSlON)
If you are parking on a hill and you don’t
shift your transmission into “P” (Park)
properly, the weight of the vehicle may
put too much force on the parking pawl in
the transmission.
You may find it difficult
to pull the shift lever out of “P” (Park).
This is called “torque lock.”
To prevent
torque lock, set
the parking brake and
then shift into “P” (Park) properly before
you leave the driver’s seat. To find out
how, see “Shifting Into “P” (Park)” in
the Index.
When you are ready to drive, move the
shift lever out of “P” (Park)
BEFORE
you release the parking brake.
If “torque lock” does occur, you may
need to have another vehicle push yours
a little uphill to take some of the pressure
From the transmission,
so you can pull the
shift lever out of “P” (Park).
... 68

Downloaded from www.Manualslib.com manuals search engine Shifting out of P (Park)
[AUTOMATIC TRANSMISSION)
Your Chevrolet has a brake-transmission
shift interlock.
You have to fully apply
your regular brake before
you can shift
from
“P’ (Park) when the ignition is in
the
“Run” position. See “Automatic
Transmission” in the Index.
If you cannot shift out of “P’ (Park), ease
pressure on the shift lever
- push the
shift lever all the way into
“P’ (Park) and
release the shift lever button
as you
maintain brake application. Then press the
shift lever button and move the shift
lever into the gear you wish.
If you ever hold the brake pedal down but
still can’t shift out of “P” (Park), try this:
1. Turn the key to ‘bOff.”
2. Apply and hold the brake until the end
3. Shift to “N” (Neutral).
4. Start the vehicle and then shift to the
drive gear
you want.
of Step 4.
5. Have the vehicle fixed as soon as you
can.
Parking Your Vehicle
(MANUAL TRANSMISSION)
Before you get out of your vehicle, put
your
manual transmission in “R”
(Reverse) and firmly apply the parking
brake.
If your vehicle is equipped to tow a trailer,
see “Towing a Trailer”
in the Index.
69 ...