CHEVROLET CAMARO SS 2010 Owners Manual

Speedometer
The speedometer shows the
vehicle’s speed in both kilometers
per hour (km/h) and miles per
hour (mph).
Odometer
The odometer shows how far the
vehicle has been driven, in
either kilometers or miles.
This vehicle has a tamper-resistant
odometer. If the vehicle needs a
new odometer installed, the new
one is set to the mileage of the old
odometer. If this is not possible, it is
set at zero and a label is put on the
driver’s door to show the old mileage
reading.
Trip Odometer
The trip odometer shows how far the
vehicle has been driven since the trip
odometer was last set to zero.
Set the odometer using the Driver
Information Center (DIC).To set the trip odometer to zero,
press and hold the SET button while
the trip odometer display is showing.
Tachometer
The tachometer displays the
engine speed in revolutions per
minute (rpm).
Fuel Gage
When the ignition is on, the fuel
gage shows about how much fuel
the vehicle has left in the fuel tank.
An arrow on the fuel gage
indicates which side of the vehicle
the fuel door is located.
The gage indicates empty before
the vehicle is out of fuel, to show
that the vehicle’s fuel tank should be
filled soon. United States
Canada
Instruments and Controls 4-11

When the fuel tank is low on fuel,
a Fuel Level Low message will
appear on the Driver Information
Center (DIC). For more information
seeFuel System Messages on
page 4-33.
Here are some situations that can
occur with the fuel gage. None of
these indicate a problem with
the fuel gage.
•At the gas station, the fuel pump
shuts off before the gage
reads full.
•It takes a little more or less fuel to
fill up than the fuel gage indicated.
For example, the gage may have
indicated the tank was half full,
but it actually took a little more or
less than half the tank’s capacity
to fill the tank.
•The pointer on the fuel gage is on
empty when the ignition is off.
Engine Oil
Pressure Gage
The oil pressure gage, located in
front of the shifter, shows the engine
oil pressure in psi (pounds per
square inch) when the engine is
running. Canadian vehicles indicate
pressure in kPa (kilopascals).
Oil pressure may vary with engine
speed, outside temperature and oil
viscosity, but readings above the low
pressure zone indicate the normal
operating range. When the oil
pressure reaches the low pressure
zone, a message appears in the
Driver Information Center (DIC). United States
Canada
4-12 Instruments and Controls

SeeEngine Oil Messages on
page 4-32andEngine Oil on
page 9-10for more information.
{WARNING
Do not keep driving if the oil
pressure is low. The engine can
become so hot that it catches fire.
Someone could be burned.
Check the oil as soon as possible
and have the vehicle serviced.
Notice:Lack of proper engine oil
maintenance can damage the
engine. The repairs would not be
covered by the vehicle warranty.
Always follow the maintenance
schedule in this manual for
changing engine oil.
A reading in the low pressure zone
can be caused by a dangerously
low oil level or some other problem
causing low oil pressure. Check
the oil as soon as possible.
Engine Oil
Temperature Gage
This gage, located in front of the
shifter, shows the engine oil
temperature.
If the gage pointer moves into the
red area, it means that the engine oil
has overheated. If the vehicle has
been operated under normal driving
conditions, pull off the road, stop
the vehicle and turn off the engine
as soon as possible.
SeeEngine Oil on page 9-10for
more information. United States
Canada
Instruments and Controls 4-13

Engine Coolant
Temperature Gage
This gage shows the engine coolant
temperature.
If the gage pointer moves towards
the H, the engine is too hot.
This reading indicates the same
thing as the warning message.
It means that the engine coolant has
overheated. If the vehicle has been
operating under normal driving
conditions, pull off the road, stop the
vehicle, and turn off the engine as
soon as possible. SeeEngine
Overheating on page 9-24for more
information.
Transmission
Temperature Gage
United States
Canada
United States
4-14 Instruments and Controls

This gage, located in front of the
shifter, shows the transmission
oil temperature when the ignition is
on. If the gage is reading in the
red area and/or a message appears
in the DIC, the vehicle must be
stopped and the cause checked.
One possible cause is a low level in
the transmission.For information on the DIC
messages seeTransmission
Messages on page 4-36.
Notice:If the vehicle is driven
with the transmission temperature
gage above the normal operating
range, the transmission can be
damaged. This could lead to
costly repairs that would not be
covered by the vehicle warranty.
Do not drive the vehicle while the
transmission temperature gage
reading is above normal. See your
dealer/retailer for service.
Voltmeter Gage
This gage, located in front of the
shifter, shows the battery’s state of
charge in DC volts.
When the engine is running, but the
ignition is on, this gage shows
the condition of the charging system.
The vehicle’s charging system
regulates voltage based on the state
of charge of the battery. It is normal
for the voltmeter to fluctuate. Canada
United States Version Shown,
Canada Similar
Instruments and Controls 4-15

Readings between the low and high
warning zones indicate the normal
operating range.
Readings in the low warning zone
can occur when a large number of
electrical accessories are operating
in the vehicle and the engine is left
idling for an extended period.
If there is a problem with the battery
charging system, a message
appears in the Driver Information
Center (DIC) and/or the charging
system light comes on. SeeBattery
Voltage and Charging Messages
on page 4-30andCharging System
Light on page 4-19for more
information.
However, readings in either warning
zone can indicate a possible
problem in the electrical system.
Have the vehicle serviced as soon
as possible.Safety Belt Reminders
Driver Safety Belt Reminder
Light
There is a driver safety belt reminder
light on the instrument panel cluster.
When the engine is started this light
and a chime come on and stay
on for several seconds to remind
drivers to fasten their safety belts.
The light also begins to flash.
This cycle repeats if the driver
remains unbuckled and the vehicle
is moving.
If the driver safety belt is already
buckled, neither the light nor chime
come on.
Passenger Safety Belt
Reminder Light
The passenger safety belt reminder
light is located on the overhead
console.
When the engine is started, this
light and the chime come on
and stay on for several seconds to
remind the passenger to fasten
their safety belt. The light also
begins to flash.
This cycle repeats if the passenger
remains unbuckled and the vehicle
is moving.
4-16 Instruments and Controls

If the passenger safety belt is
buckled, neither the chime nor the
light comes on.
The front passenger safety belt
warning light and chime may turn
on if an object is put on the
seat such as a briefcase, handbag,
grocery bag, laptop or other
electronic device. To turn off the
warning light and or chime, remove
the object from the seat or buckle
the safety belt
Airbag Readiness Light
This light shows if there is an
electrical problem. The system
check includes the airbag sensor,
the pretensioners, the airbag
modules, the wiring and the crash
sensing and diagnostic module.For more information on the airbag
system, seeAirbag System on
page 2-21.
The airbag readiness light comes on
and stays on for several seconds
when the vehicle is started. Then the
light goes out.
If it stays on after the vehicle has
been started or comes on while
driving, the airbag system may not
work properly. Have the vehicle
serviced right away.
{WARNING
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inflate in a
crash, or they could even inflate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
Instruments and Controls 4-17

Passenger Airbag Status
Indicator
The vehicle has a passenger
sensing system. SeePassenger
Sensing System on page 2-28
for important safety information.
The overhead console has a
passenger airbag status indicator.When the vehicle is started, the
passenger airbag status indicator
will light ON and OFF, or the symbol
for on and off, for several seconds
as a system check. If you are
using remote start to start your
vehicle from a distance, if equipped,
you may not see the system
check. Then, after several seconds,
the status indicator will light either
ON or OFF, or either the on or
off symbol to let you know the status
of the right front passenger frontal
airbag.
If the word ON or the on symbol is
lit on the passenger airbag status
indicator, it means that the right front
passenger frontal airbag is enabled
(may inflate).If the word OFF or the off symbol is
lit on the passenger airbag status
indicator, it means that the
passenger sensing system has
turned off the right front passenger
frontal airbag.
If, after several seconds, both status
indicator lights remain on, or if
there are no lights at all, there may
be a problem with the lights or
the passenger sensing system.
See your dealer/retailer for service.
{WARNING
If the airbag readiness light ever
comes on and stays on, it means
that something may be wrong with
the airbag system. To help avoid
injury to yourself or others, have
the vehicle serviced right away.
SeeAirbag Readiness Light on
page 4-17for more information,
including important safety
information. United States
Canada
4-18 Instruments and Controls

Charging System Light
The charging system light comes on
briefly when the ignition is turned
on but the engine is not running,
as a check to show the light is
working. It should go out when the
engine is started.
If the light stays on, or comes on
while driving, there may be a
problem with the electrical charging
system. Have it checked by your
dealer/retailer. Driving while this light
is on could drain the battery.
When this light comes on, the Driver
Information Center (DIC) also
displays a message.
SeeBattery Voltage and Charging
Messages on page 4-30.If a short distance must be driven
with the light on, be sure to turn off
all accessories, such as the radio
and air conditioner.
Malfunction
Indicator Lamp
Check Engine Light
A computer system called OBD II
(On-Board Diagnostics-Second
Generation) monitors operation of
the fuel, ignition, and emission
control systems. It ensures that
emissions are at acceptable levels
for the life of the vehicle, helping
to produce a cleaner environment.
This light comes on when the
ignition is on, but the engine is not
running, as a check to show itis working. If it does not, have
the vehicle serviced by your
dealer/retailer.
If the check engine light comes on
and stays on, while the engine
is running, this indicates that there
is an OBD II problem and service
is required.
Malfunctions often are indicated by
the system before any problem
is apparent. Being aware of the light
can prevent more serious damage
to the vehicle. This system assists
the service technician in correctly
diagnosing any malfunction.
Notice:If the vehicle is
continually driven with this light
on, after a while, the emission
controls might not work as well,
the vehicle’s fuel economy might
not be as good, and the engine
might not run as smoothly.
This could lead to costly repairs
that might not be covered by the
vehicle warranty.
Instruments and Controls 4-19

Notice:Modications made
to the engine, transmission,
exhaust, intake, or fuel system of
the vehicle or the replacement
of the original tires with other
than those of the same Tire
Performance Criteria (TPC) can
affect the vehicle’s emission
controls and can cause this light
to come on. Modications to
these systems could lead to
costly repairs not covered by
the vehicle warranty. This could
also result in a failure to
pass a required Emission
Inspection/Maintenance test.
SeeAccessories and
Modifications on page 9-3.This light comes on during a
malfunction in one of two ways:
Light Flashing:A misfire condition
has been detected. A misfire
increases vehicle emissions and
could damage the emission control
system on the vehicle. Diagnosis
and service might be required.
The following can prevent more
serious damage to the vehicle:
•Reduce vehicle speed.
•Avoid hard accelerations.
•Avoid steep uphill grades.
If the light continues to flash,
when it is safe to do so, stop the
vehicle. Find a safe place to
park the vehicle. Turn the engine
off, wait at least 10 seconds,
and restart the engine. If the light
is still flashing, follow the previous
steps and see your dealer/retailer
for service as soon as possible.Light On Steady:An emission
control system malfunction has been
detected on the vehicle. Diagnosis
and service might be required.
An emission system malfunction
might be corrected by:
•Make sure the fuel cap is fully
installed. SeeFilling the Tank
on page 8-46. The diagnostic
system can determine if the
fuel cap has been left off or
improperly installed. A loose or
missing fuel cap allows fuel
to evaporate into the atmosphere.
A few driving trips with the cap
properly installed should turn
the light off.
•If the vehicle has been driven
through a deep puddle of water,
the vehicle’s electrical system
might be wet. The condition is
usually corrected when the
electrical system dries out.
A few driving trips should turn
the light off.
4-20 Instruments and Controls