wiring CHEVROLET SILVERADO 2017 3.G Owners Manual
[x] Cancel search | Manufacturer: CHEVROLET, Model Year: 2017, Model line: SILVERADO, Model: CHEVROLET SILVERADO 2017 3.GPages: 509, PDF Size: 8.87 MB
Page 88 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Seats and Restraints 87
{Warning
For up to 10 seconds after the
vehicle is turned off and the
battery is disconnected, an airbag
can still inflate during improper
service. You can be injured if you
are close to an airbag when it
inflates. Avoid yellow connectors.
They are probably part of the
airbag system. Be sure to follow
proper service procedures, and
make sure the person performing
work for you is qualified to do so.
Adding Equipment to the
Airbag-Equipped Vehicle
Adding accessories that change thevehicle's frame, bumper system,height, front end, or side sheetmetal, may keep the airbag systemfrom working properly. Theoperation of the airbag system canalso be affected by changing anyparts of the front seats, safety belts,the airbag sensing and diagnosticmodule, steering wheel, instrumentpanel, any of the airbag modules,
ceiling headliner or pillar garnishtrim, overhead console, frontsensors, side impact sensors,or airbag wiring.
Yo u r d e a l e r a n d t h e s e r v i c e m a n u a lhave information about the locationof the airbag sensors, sensing anddiagnostic module, and airbagwiring.
In addition, the vehicle may have apassenger sensing system for thefront outboard passenger position,which includes sensors that are partof the passenger seat. Thepassenger sensing system may notoperate properly if the original seattrim is replaced with non-GMcovers, upholstery, or trim; or withGM covers, upholstery, or trimdesigned for a different vehicle. Anyobject, such as an aftermarket seatheater or a comfort-enhancing pador device, installed under or on topof the seat fabric, could alsointerfere with the operation of thepassenger sensing system. Thiscould either prevent properdeployment of the passengerairbag(s) or prevent the passengersensing system from properly
turning off the passenger airbag(s).SeePassenger SensingSystem082.
If the vehicle has rollover roof-railairbags, seeDifferent Size Tiresand Wheels0416for additionalimportant information.
If a snow plow is added to thevehicle, the airbags should still workproperly. The airbag systems weredesigned to work properly under awide range of conditions, includingsnow plowing with vehicles thathave the optional snow plow preppackage (RPO VYU). Do notchange or defeat the snow plow's“tripping mechanism.”If you do, itcan damage the snow plow and thevehicle, and may cause an airbagdeployment.
If you have to modify your vehiclebecause you have a disability andyou have questions about whetherthe modifications will affect thevehicle's airbag system, or if youhave questions about whether theairbag system will be affected if thevehicle is modified for any other
Page 136 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Instruments and Controls 135
Passenger Safety Belt
Reminder Light
There may be a passenger safetybelt reminder light near thepassenger airbag status indicator.SeePassenger SensingSystem082.
For vehicles equipped with thepassenger safety belt reminder light,when the vehicle is started this lightflashes and a chime may come onto remind passengers to fasten theirsafety belt. Then the light stays onsolid until the belt is buckled. Thiscycle continues several times if thepassenger remains or becomesunbuckled while the vehicle ismoving.
If the passenger safety belt isbuckled, neither the chime nor thelight comes on.
The front passenger safety beltreminder light and chime may turnon if an object is put on the seatsuch as a briefcase, handbag,grocery bag, laptop, or otherelectronic device. To turn off thereminder light and/or chime, removethe object from the seat or bucklethe safety belt.
Airbag Readiness Light
This light shows if there is anelectrical problem with the airbagsystem. The system check includesthe airbag sensor(s), passengersensing system (if equipped), thepretensioners, the airbag modules,the wiring, and the crash sensingand diagnostic module. For moreinformation on the airbag system,seeAirbag System074.
The airbag readiness light comes onfor several seconds when thevehicle is started. If the light doesnot come on then, have it fixedimmediately.
{Warning
If the airbag readiness light stays
on after the vehicle is started or
comes on while driving, it means
the airbag system might not be
working properly. The airbags in
the vehicle might not inflate in a
crash, or they could even inflate
without a crash. To help avoid
injury, have the vehicle serviced
right away.
If there is a problem with the airbagsystem, a Driver Information Center(DIC) message may also come on.SeeAirbag SystemMessages0155.
Page 152 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Instruments and Controls 151
SERVICE BATTERY
CHARGING SYSTEM
On some vehicles, this messagedisplays if there is a problem withthe battery charging system. Undercertain conditions, the chargingsystem light may also turn on in theinstrument cluster. SeeChargingSystem Light0138.Drivingwiththisproblem could drain the battery.Turn off all unnecessaryaccessories. Have the electricalsystem checked as soon aspossible. See your dealer.
TRANSPORT MODE ON
This message is displayed when thevehicle is in transport mode. Somefeatures can be disabled while inthis mode, including RemoteKeyless Entry (RKE), remote start,and the vehicle alarm system. Takethe vehicle to your dealer for serviceto turn transport mode off.
Brake System Messages
BRAKE FLUID LOW
This message is displayed when thebrake fluid level is low. SeeBrakeFluid0377.
SERVICE BRAKE ASSIST
This message may be displayedwhen there is a problem with thebrake boost assist system. Whenthis message is displayed, the brakeboost assist motor might be heardoperating and you might noticepulsation in the brake pedal. This isnormal under these conditions. Takethe vehicle to your dealer forservice.
SERVICE TRAILER BRAKE
SYSTEM
On vehicles with the IntegratedTrailer Brake Control (ITBC) system,this message displays and a chimemay sound when there is a problemwith the ITBC system.
When this message displays, poweris no longer available to the trailerbrakes.
As soon as it is safe to do so,carefully pull your vehicle over tothe side of the road and turn theignition off. Check the wiringconnection to the trailer and turn theignition back on. If this message stilldisplays, either your vehicle or thetrailer needs service. See yourdealer.
See“Integrated Trailer BrakeControl System”underTo w i n gEquipment0335for moreinformation.
Compass Messages
Dashes may be displayed if thevehicle temporarily losescommunication with the GlobalPositioning System (GPS).
Door Ajar Messages
DOOR OPEN
This message displays and a chimemay sound if a door is not fullyclosed. Stop and turn off thevehicle, check the door for
Page 160 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Instruments and Controls 159
TRANSMISSION HOT IDLE
ENGINE
This message displays and a chimemay sound if the transmission fluidin the vehicle gets hot. Driving withthe transmission fluid temperaturehigh can cause damage to thevehicle. Stop the vehicle and let itidle to allow the transmission tocool. This message clears and thechime stops when the fluidtemperature reaches a safe level.
When towing, use Tow/Haul Modeto prevent damage to the engine ortransmission. SeeTo w / H a u lMode0282.
VEHICLE IN 4WD LOW
This message will display if the
vehicle is driven in 4nfor about
10 minutes above 72 km/h (45 mph).
Vehicle Reminder
Messages
CHECK TRAILER WIRING
On vehicles with the IntegratedTrailer Brake Control (ITBC) system,this message may display and achime may sound when one of thefollowing conditions exists:
.Atrailerwithelectricbrakesbecomes disconnected from thevehicle.
⇣If the disconnect occurs whilethe vehicle is stopped, thismessage clears itself after ashort time.
⇣If the disconnect occurs whilethe vehicle is moving, thismessage stays on until theignition is turned off.
.There is a short in the wiring tothe electric trailer brakes.
When this message displays, poweris no longer available to the trailerbrakes.
As soon as it is safe to do so,carefully pull the vehicle over to theside of the road and turn the ignitionoff. Check the wiring connection tothe trailer and turn the ignition backon. This message clears if the traileris reconnected. This message alsoclears if you acknowledge it. If thismessage still displays, either thevehicle or the trailer needs service.See your dealer.
See“Integrated Trailer BrakeControl System”underTo w i n gEquipment0335.
ICE POSSIBLE DRIVE
WITH CARE
This message displays when iceconditions are possible.
TRAILER CONNECTED
On vehicles with the IntegratedTrailer Brake Control (ITBC) system,this message displays briefly whenatrailerwithelectricorelectricoverhydraulic brakes is first connectedto the vehicle.
Page 177 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
176 Lighting
The lever returns to its startingposition whenever it is released.
If after signaling a turn or a lanechange the arrows flash rapidly ordo not come on, a signal bulb couldbe burned out. If equipped with LEDturn signals, see your dealer.
Replace any burned out bulbs. If abulb is not burned out, check thefuse. SeeFuses0390.
Turn Signal On Chime
If the turn signal is left on for morethan 1.2 km (0.75 mi), a chimesounds at each flash of the turnsignal. The message TURNSIGNAL ON will also appear in theDriver Information Center (DIC). Toturn the chime and message off,move the turn signal lever to the offposition.
Fog Lamps
If equipped, the control is on thecenter of the exterior lamp control,to the left of the steering column.
The ignition must be in the ON/RUNposition for the fog lamps tocome on.
#:Press to turn the fog lamps onor off. A light will come on in theinstrument cluster.
When the fog lamps are turned on,the parking lamps automaticallyturn on.
When the headlamps are changedto high beam, the fog lamps go off.When the high-beam headlamps areturned off, the fog lamps will comeon again.
Some localities have laws thatrequire the headlamps to be on withthe fog lamps.
Auxiliary
Roof-Mounted Lamp
If equipped, this button includeswiring provisions for a dealer or aqualified service center to install anauxiliary roof lamp.
This button is on the overheadconsole.
When the wiring is connected to anauxiliary roof-mounted lamp,pressing the bottom of the buttonwill activate the lamp and illuminatean indicator light at the bottom of
Page 338 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 5/6/16
Driving and Operating 337
pickups. Trailer pin box extensionsand sliding fifth-wheel hitchassemblies can help this condition.There should be at least 15 cm (6 in)of clearance between the top of thepickup box and the bottom of thetrailer shelf that extends overthe box.
Safety Chains
Always attach chains between thevehicle and the trailer. Cross thesafety chains under the tongue ofthe trailer to help prevent the tonguefrom contacting the road if itbecomes separated from the hitch.Instructions about safety chainsmay be provided by the hitchmanufacturer or by the trailermanufacturer. If the trailer beingtowed weighs up to 2 271 kg(5,000 lb) with a factory-installedstep bumper, safety chains may beattached to the attaching points onthe bumper; otherwise, safetychains should be attached to holeson the trailer hitch platform. Alwaysleave just enough slack so thecombination can turn. Never allowsafety chains to drag on the ground.
Trailer Brakes
Aloadedtrailerthatweighsmorethan 900 kg (2,000 lb) must beequipped with its own brake system,with brakes working on all axles.Trailer braking equipmentconforming to Canadian StandardsAssociation (CSA) requirementCAN3-D313, or its equivalent, isrecommended.
State and local regulations may alsorequire the trailer to have its ownbraking system if loaded above acertain threshold.
Be sure to read and follow theinstructions for the trailer brakes sothey are installed, adjusted, andmaintained properly.
Do not tap into the vehicle'shydraulic brake system.
Auxiliary Battery
The auxiliary battery provision canbe used to supply electrical powerto additional equipment that may beadded, such as a slide-in camper.If equipped, this relay will be on thedriver side of the vehicle, next to theunderhood electrical center.
Be sure to follow the properinstallation instructions included withany electrical equipment that isinstalled.
Caution
Leaving electrical equipment on
for extended periods will drain the
battery. Always turn off electrical
equipment when not in use and
do not use equipment that
exceeds the maximum amperage
rating of 30 amps for the auxiliary
battery provision.
Trailer Wiring Harness
The vehicle is equipped with one ofthe following wiring harnesses fortowing a trailer or hauling a slide-incamper.
Basic Trailer Wiring
All regular, double cab, and crewcab pickups have a seven-wiretrailer towing harness.
Page 339 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 5/6/16
338 Driving and Operating
Use only a round, seven-wireconnector with flat blade terminalsmeeting SAE J2863 specificationsfor proper electrical connectivity.
For vehicles not equipped withheavy-duty trailering, the harness issecured to the vehicle's framebehind the spare tire mount. Theharness requires the installation of atrailer connector, which is availablethrough your dealer.
Heavy-Duty Trailer Wiring HarnessPackage
For vehicles equipped withheavy-duty trailering, the harnessconnector is mounted in the bumper.
For vehicles with the fifth wheel/gooseneck trailer package, theharness connector is mounted onthe inside of the pickup bed behindthe rear wheel.
The seven-wire harness containsthe following trailer circuits:
.Green/Violet: Right Stop/TurnSignal
.Ye l l o w / G r a y : L e f t S t o p / T u r nSignal
.Gray/Brown: Taillamps/ParkingLamps
.White: Ground
.White/Green: Back-up Lamps
.Red/Green: Battery Feed
.Dark Blue: Trailer Brake
To h e l p c h a r g e a r e m o t e(non-vehicle) battery, press the Tow/Haul Mode button at the end of theshift lever. If the trailer is too light forTo w / H a u l M o d e , t u r n o n t h eheadlamps to help charge thebattery.
Camper/Fifth-Wheel Trailer WiringPackage
For vehicles without the fifth wheel/gooseneck tralier package,seven-wire camper harness is underthe rear bumper, attached to theframe near the rear crossmember.Aconnectormustbeaddedtothewiring harness that connects to thecamper.
The harness contains the followingcamper/trailer circuits:
.Green/Violet: Right Stop/TurnSignal
.Ye l l o w / G r a y : L e f t S t o p / T u r nSignal
.Gray/Brown: Taillamps/ParkingLamps
Page 340 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Driving and Operating 339
.White: Ground
.White/Green: Back-up Lamps
.Red/Green: Battery Feed
.Dark Blue: Trailer Brake
If the vehicle is equipped with theheavy-duty trailering option, see“Heavy-Duty Trailer Wiring HarnessPackage”earlier in this section.
When the camper-wiring harness isordered without the heavy-dutytrailering package, a seven-wireharness with a seven-pin connectoris at the rear of the vehicle and istied to the vehicle's frame.
Electric Brake Control Wiring
Provisions
These wiring provisions areincluded with the vehicle as part ofthe trailer wiring package. Theseprovisions are for an electric brakecontroller.
The harness should be installed byyour dealer or a qualified servicecenter.
Tow/Haul Mode
Pressing this button at the end ofthe shift lever turns on and off theTo w / H a u l M o d e .
This indicator light on the instrumentcluster comes on when the Tow/Haul Mode is on.
To w / H a u l i s a f e a t u r e t h a t a s s i s t swhen pulling a heavy trailer or alarge or heavy load. SeeTo w / H a u lMode0282.
To w / H a u l i s d e s i g n e d t o b e m o s teffective when the vehicle andtrailer combined weight is at least75% of the vehicle's GrossCombined Weight Rating (GCWR).See“Weight of the Trailer”underTr a i l e r To w i n g0318.Tow/Haulismost useful under the followingdriving conditions:
.When pulling a heavy trailer or alarge or heavy load throughrolling terrain.
.When pulling a heavy trailer or alarge or heavy load instop-and-go traffic.
.When pulling a heavy trailer or alarge or heavy load in busyparking lots where improved lowspeed control of the vehicle isdesired.
Operating the vehicle in Tow/Haulwhen lightly loaded or with no trailerat all will not cause damage.However, there is no benefit to the
Page 342 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
Driving and Operating 341
Trailer Brake Control Panel
1. Manual Trailer Brake ApplyLever
2. Trailer Gain AdjustmentButtons
The ITBC system has a controlpanel on the instrument panel to theleft of the steering column. SeeInstrument Panel06.Thecontrolpanel allows adjustment to theamount of output, referred to asTrailer Gain, available to the trailerbrakes and allows manualapplication of the trailer brakes. TheTrailer Brake Control Panel is usedalong with the Trailer Brake Display
Page on the Driver InformationCenter (DIC) to adjust and displaypower output to the trailer brakes.
Trailer Brake DIC Display Page
The ITBC system displaysmessages in the DIC.
The display page indicates TrailerGain setting, power output to thetrailer brakes, trailer connection, andsystem operational status.
To d i s p l a y t h e T r a i l e r B r a k e D i s p l a yPage, do any of the following:
.Scroll through the DIC menupages.
.Press a Trailer Gain button.If the Trailer Brake Display Pageis not currently displayed, pressaTrailerGainbuttontorecallthecurrent Trailer Gain setting.Each press and release of thegain buttons will then change theTrailer Gain setting.
.Activate the Manual TrailerBrake Apply Lever.
TRAILER GAIN: This setting can beadjusted from 0.0 to 10.0 with eitheratrailerconnectedordisconnected.
To a d j u s t t h e T r a i l e r G a i n , p r e s s o n eof the Trailer Gain Adjustmentbuttons. Press and hold a gainbutton to continuously adjust theTrailer Gain. To turn the output tothe trailer off, adjust the Trailer Gainsetting to 0.0 (zero).
TRAILER OUTPUT: This displaysanytime a trailer with electric brakesis connected. Output to the trailerbrakes is based on the amount ofvehicle braking present and relativeto the Trailer Gain setting. Output isdisplayed from 0 to 100% for eachgain setting.
The Trailer Output will indicate“------”on the Trailer BrakeDisplay Page whenever thefollowing occur:
.No trailer is connected.
.Atrailerwithoutelectricbrakesis connected (no DIC messagewill display).
.Atrailerwithelectricbrakeshasbecome disconnected (aCHECK TRAILER WIRINGmessage will also display onthe DIC).
Page 343 of 509
Chevrolet Silverado Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-9956065) - 2017 - CRC - 4/29/16
342 Driving and Operating
.There is a fault present in thewiring to the trailer brakes (aCHECK TRAILER WIRINGmessage will also display onthe DIC).
.The ITBC system is not workingdue to a fault (a SERVICETRAILER BRAKE SYSTEMmessage will also display inthe DIC).
Manual Trailer Brake Apply
The Manual Trailer Brake ApplyLever is used to apply the trailer’selectric brakes independent of thevehicle’sbrakes.Slidingthelevertothe left will apply only the trailerbrakes. Use this lever to adjustTrailer Gain to properly adjust thepower output to the trailer brakes.
The trailer's and the vehicle's brakelamps will come on when eithervehicle brakes or manual trailerbrakes are applied.
Trailer Gain Adjustment Procedure
Trailer Gain should be set for aspecific trailering condition and mustbe adjusted anytime vehicle loading,trailer loading, or road surfaceconditions change.
{Warning
Trailer brakes that are
over-gained or under-gained may
not stop the vehicle and the trailer
as intended and can result in a
crash. Always follow the
instructions to set the Trailer Gain
for the proper trailer stopping
performance.
Use the following to adjust TrailerGain for each towing condition:
1. Drive the vehicle with the trailerattached on a level roadsurface representative of thetowing condition and free oftraffic at about 32 to 40 km/h(20 to 25 mph) and fully applythe Manual Trailer Brake ApplyLever.
Adjusting Trailer Gain atspeeds lower than 32 to40 km/h (20 to 25 mph) mayresult in an incorrect gainsetting.
2. Adjust the Trailer Gain, usingthe Trailer Gain AdjustmentButtons, to just below the pointof trailer wheel lock-up,indicated by trailer wheelsqueal or tire smoke when atrailer wheel locks.
Trailer wheel lock-up may notoccur if towing a heavily loadedtrailer. In this case, adjust theTrailer Gain to the highestallowable setting for the towingcondition.
3. Readjust Trailer Gain anytimevehicle loading, trailer loading,or road surface conditionschange or if trailer wheellock-up is noticed at any timewhile towing.