key CHRYSLER CARAVAN 2000 Manual Online

TEST NTC-10BCHECKING THE FUEL HEATER AND THE CRANKCASE VENT HEATER
Perform TEST NTC-10A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST
NTC-10B. TURN IGNITION OFF.
REPLACE FUSE #16.
NO
TURN IGNITION ON IS THE FUSE OPEN? TEST COMPLETE.*
AND INSPECT FUSE
#16.
YES
CONNECT A JUMPER
REMOVE FUEL HEATER WIRE ACROSS FUEL
RELAY. HEATER RELAY
CAVITIES 30 & 87
(IN PDC). FIG. 1
REPLACE FUSE #6 NO REPLACE THE FUEL
IS THE FUSE OPEN? HEATER RELAY.*
TURN IGNITION ON.
YES
KEY OFF. REPLACE FUSE #16 AND
TURN IGNITION ON. NO REPLACE THE FUEL
DISCONNECT THE IS THE FUSE OPEN? HEATER.*
FUEL HEATER INSPECT FUSE #16.
HARNESS CONNECTOR.
YES
KEY OFF. REPLACE FUSE #16 AND
DISCONNECT THE TURN IGNITION ON. NO REPLACE THE
CRANKCASE VENT IS THE FUSE OPEN? CRANKCASE VENT
HEATER HARNESS INSPECT FUSE #16. HEATER.*
CONNECTOR.
YES
REPAIR THE FUEL
HEATER RELAY
OUTPUT CIRCUIT FOR
A SHORT TO
GROUND.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
351
ProCarManuals.com

TEST NTC-11ACONTINUED - CHECKING RADIATOR FAN OPERATION
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST NTC-11A
CONTINUED FROM
THE PREVIOUS TURN IGNITION OFF.
PAGE.
KEY ON. REPAIR SHORT TO
REMOVE RAD FAN DOES THE LEFT SIDE YES GROUND IN RAD FAN
RELAY #1.** USING THE DRB, RAD FAN CYCLE ON GROUND CKT. BETWEEN
ACTUATE LOW SPEED AND OFF? LEFT SIDE RAD FAN
RAD FAN. AND RELAY #1*
NO
KEY OFF. USE AN BETWEEN RAD FAN
OHMMETER IN THE RELAY #1 TERMINALS IS THE RESISTANCE YES REPLACE THE RAD
FOLLOWING STEPS. 30 AND 87. BELOW 5.0 OHMS? FAN RELAY #1.*
MEASURE THE
RESISTANCE... FIG.1
NO
DISCONNECT THE MEASURE RESISTANCE REPAIR THE SHORT
RIGHT SIDE RAD FAN BETWEEN RAD FAN IS THE RESISTANCE YES TO GROUND IN THE
HARNESS RELAY #1 HARNESS BELOW 5.0 OHMS? RAD FAN RELAY #3
CONNECTOR.** CONNECTOR CAVITY 5 OUTPUT CIRCUIT.*
AND GROUND. FIG.2
NO
REPLACE THE RIGHT
SIDE RADIATOR
FAN.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
355
ProCarManuals.com

TEST NTC-11DCHECKING RADIATOR FAN OPERATION
Perform TEST NTC-11A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST STOP LOW SPEED FAN
NTC-11D. ACTUATION.
KEY OFF.
SUBSTITUTE THE RAD PERFORM THE DO BOTH FANS CYCLE YES REPLACE THE
FAN #1 RELAY WITH "LOW SPEED FAN" ON AND OFF? INITIAL RAD FAN #1
A KNOWN GOOD ACTUATOR TEST. RELAY.*
RELAY.
NO
DISCONNECT THE
DISCONNECT RAD FAN LEFT SIDE FAN
#1 RELAY HARNESS MOTOR HARNESS
CONNECTOR.** CONNECTOR.**
USING AN OHMMETER, REPAIR THE SHORT
MEASURE THE GROUND IS THE RESISTANCE YES TO GROUND BETWEEN
CKT AT CAVITY 8 TO BELOW 10.0 OHMS? THE LEFT SIDE
GROUND. MOTOR AND RAD FAN
FIG.1 #1 REKAY.
NO
DISCONNECT THE USING AN OHMMETER, REPAIR THE RIGHT
RIGHT SIDE FAN MEASURE CAVITY 5 IS THE RESISTANCE YES SIDE FAN SUPPLY
MOTOR HARNESS TO GROUND. BELOW 10.0 OHMS? CIRCUIT FOR A
CONNECTOR.** SHORT TO GROUND.*
FIG.1
NO
CHECK RIGHT SIDE IS ANYTHING
FAN MOTOR FOR PREVENTING THE FAN YES REPAIR AS
BINDING OR DEBRIS MOTOR FROM NECESSARY.
WHICH MAY PREVENT TURNING?
FAN OPERATION.
NO
REPLACE THE RIGHT
SIDE FAN MOTOR.*
N
O
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
365
ProCarManuals.com

TEST SC-1ACHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST KEY ON. WITH THE
SC-1A. DRB, SELECT
"SENSOR DISPLAY".
PRESS EACH OF THE PRESSING EACH SWITCH DID EACH SWITCH
CRUISE SWITCH SHOULD RESULT IN A PROVIDE THE NO PERFORM TEST
BUTTONS WHILE VOLTAGE INPUT SHOWN CORRECT VOLTAGE SC-2A.
OBSERVING CRUISE IN FIG.1. INPUT.
SWITCH VOLTS.
YES
WITH THE DRB, DID THE DRB INDICATE
MONITOR THE WHILE PRESSING AND THE CORRECT CHANGE NO PERFORM TEST
PRIMARY AND RELEASING THE OF STATE FROM SC-3A.
SECONDARY BRAKE BRAKE PEDAL. "RELEASED" TO
SWITCH INPUT... "PRESSED".
YES
DID THE DRB INDICATE
WITH THE DRB, WHILE PRESSING AND THE CORRECT CHANGE NO PERFORM TEST
MONITOR THE CLUTCH RELEASING THE OF STATE FROM SC-4A.
SWITCH INPUT. CLUTCH PEDAL. "RELEASED" TO
"PRESSED".
YES
WITH THE DRB,
MONITOR VEHICLE DOES THE DRB NO PERFORM TEST
SPEED WHILE DISPLAY ACCURATE SC-6A.
DRIVING THE VEHICLE SPEED?
VEHICLE.
YES
DRIVE VEHICLE AND ATTEMPT TO SET DID THE SPEED YES
GENERATE A SPEED SPEED CONTROL. CONTROL MAINTAIN TEST COMPLETED.*
ABOVE 35KM/H. SET VEHICLE SPEED?
NO
CONTINUE TEST
SC-1A ON THE
NEXT PAGE.
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
373
ProCarManuals.com

TEST SC-2ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
KEY OFF.
START TEST DISCONNECT THE
SC-2A. CLOCKSPRING
HARNESS
CONNECTOR.**
KEY ON. USING THE A JUMPER WIRE DID THE VOLTAGE
DRB, MONITOR THE ACROSS CLOCKSPRING CHANGE FROM YES REPLACE THE SPEED
CRUISE SWITCH HARNESS CONNECTOR APPROXIMATELY 5.0 CONTROL SWITCHES.*
VOLTAGE WHILE CAVITIES 3 AND 4. VOLTS TO 0 VOLTS?
CONNECTING... FIG.1
NO
KEY ON. PROBE THE REPAIR THE OPEN
USE A VOLTMETER IN CLOCKSPRING IS THE VOLTAGE YES SPEED CONTROL
THE FOLLOWING HARNESS CONNECTOR ABOVE 4.0 VOLTS? SWITCH GROUND
STEP. CAVITY 4. CIRCUIT.*
NO
KEY OFF. USING AN OHMMETER,
DISCONNECT THE ECM MEASURE THE SPEED IS THE RESISTANCE YES REPAIR THE OPEN
HARNESS CONTROL SWITCH ABOVE 5.0 OHMS? SPEED CONTROL
CONNECTORS.** CIRCUIT. SWITCH CIRCUIT.*
FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
377
ProCarManuals.com

TEST SC-3ACONTINUED - CHECKING SPEED CONTROL OPERATION
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
TEST SC-3A KEY OFF.
CONTINUED FROM
THE PREVIOUS DISCONNECT THE BRAKE
PAGE. LAMP SWITCH HARNESS
CONNECTOR.**
USING A VOLTMETER, REPAIR THE BRAKE
PROBE BRAKE LAMP IS THE VOLTAGE NO LAMP SWITCH FUSED
SWITCH HARNESS ABOVE 9.0 VOLTS? BATTERY SUPPLY
CONNECTOR CAVITY 6. CIRCUIT FOR AN
FIG.1 OPEN.*
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN BRAKE LAMP DISPLAY CHANGE YES ADJUST OR REPLACE
SWITCH HARNESS TURN IGNITION ON. FROM "RELEASED" TO THE BRAKE LAMP
CONNECTOR CAVITIES "PRESSED"? SWITCH.*
5 AND 6. FIG.1
NO
REMOVE THE JUMPER. AT THE BRAKE LAMP REPAIR THE PRIMARY
USING A VOLTMETER, SWITCH HARNESS IS THE VOLTAGE NO BRAKE SWITCH
MEASURE THE CONNECTOR CAVITY 5. BELOW 1.0 VOLT? SIGNAL CIRCUIT FOR
PRIMARY SWITCH A SHORT TO
SIGNAL CIRCUIT... FIG.1 VOLTAGE.*
YES
KEY OFF. USING AN OHMMETER, REPAIR THE PRIMARY
MEASURE RESISTANCE IS THE RESISTANCE NO BRAKE SWITCH
DISCONNECT THE ECM OF THE PRIMARY BRAKE BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
HARNESS SW SIGNAL CKT. AN OPEN.*
CONNECTORS.** FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
381
ProCarManuals.com

TEST SC-3BCHECKING SPEED CONTROL OPERATION
Perform TEST SC-3A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-3B. TURN IGNITION OFF.
DISCONNECT THE KEY ON. USING A
BRAKE LAMP SWITCH VOLTMETER, MEASURE IS THE VOLTAGE NO CONTINUE TEST
HARNESS VOLTAGE AT CAVITY 1. ABOVE 9.0 VOLTS? SC-3B ON THE
CONNECTOR.** NEXT PAGE.
FIG.1
YES
USING A JUMPER WHILE MONITORING DID THE DRB
WIRE, CONNECT THE DRB. DISPLAY CHANGE YES ADJUST OR REPLACE
BRAKE LAMP SWITCH FROM "PRESSED" TO THE BRAKE LAMP
CONNECTOR CAVITY 1 "RELEASED"? SWITCH.*
TO GROUND... FIG.1
NO
USING AN OHMMETER,REPAIR THE OPEN
MEASURE THE IS THE RESISTANCE YES SECONDARY BRAKE
RESISTANCE BETWEEN ABOVE 10.0 OHMS? LAMP SWITCH GROUND
CONNECTOR CAVITY 2CIRCUIT.*
AND GROUND. FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
383
ProCarManuals.com

TEST SC-4ACHECKING SPEED CONTROL OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
START TEST
SC-4A. TURN IGNITION OFF.
DISCONNECT THE USING AN OHMMETER, REPAIR OPEN IN
CLUTCH PEDAL MEASURE RESISTANCE IS THE RESISTANCE NO CLUTCH PEDAL
SWITCH HARNESS BETWEEN CLUTCH PEDAL BELOW 5.0 OHMS? SWITCH GROUND
CONNECTOR.** SW.CONNECTOR CAVITY CIRCUIT.*
2 AND GROUND. FIG.1
YES
KEY ON. WHILE THE CLUTCH PEDAL CHECK ADJUSTMENT OF
OBSERVING THE DRB, SWITCH HARNESS DID THE DRB CHANGE YES CLUTCH PEDAL SWITCH.
CONNECT A JUMPER CONNECTOR CAVITIES FROM "RELEASED" TO IF ADJUSTMENT IS OK,
WIRE ACROSS... 1 AND 2. "PRESSED"? REPLACE THE CLUTCH
FIG.1 PEDAL SWITCH.*
NO
KEY OFF. USING AN OHMMETER,
DISCONNECT THE ECM MEASURE THE IS THE RESISTANCE NO REPAIR OPEN CLUTCH
HARNESS RESISTANCE OF THE BELOW 5.0 OHMS? PEDAL SWITCH SENSE
CONNECTORS.** CLUTCH PEDAL SWITCH CIRCUIT.*
CIRCUIT. FIG.2
YES
ECM HARNESS REPAIR CLUTCH
USING AN OHMMETER CONNECTOR CAVITY IS THE RESISTANCE NO PEDAL SWITCH SENSE
MEASURE RESISTANCE 46 AND GROUND. ABOVE 5.0 OHMS? CIRCUIT FOR SHORT
BETWEEN... TO GROUND.*
FIG. 1
YES
REPLACE THE ENGINE
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
387
ProCarManuals.com

TEST SC-6ACHECKING CRUISE INDICATOR OPERATION
Perform TEST SC-1A Before Proceeding
*Perform Verification TEST VER-3A. **Check connectors - Clean / repair as necessary.
NOTE: PERFORM TEST
START TEST SC-1A TO VERIFY
SC-6A. PROPER CRUISE
SWITCH OPERATION
BEFORE CONTINUING.
TURN IGNITION ON. MONITOR CRUISE DOES LAMP STATE CHECK CRUISE LAMP
WITH THE DRB SELECT LAMP STATE WHILE CHANGE FROM "ON" YES BULB, REPLACE AS
"BODY" "MIC" PRESSING CRUISE TO "OFF" WHEN NECESSARY. IF OK,
"MONITOR DISPLAY" ON/OFF BUTTON PRESSING THE REPLACE THE
THEN "CCD BUS INFO". SEVERAL TIMES. BUTTON? INSTRUMENT CLUSTER.*
NO
KEY OFF. KEY ON. CONNECT A
DISCONNECT THE ECM JUMPER WIRE BETWEEN IS THE SPEED YES REPLACE THE ENGINE
HARNESS ECM HARNESS CONTROL LAMP ON? CONTROL MODULE.*
CONNECTORS.** CONNECTOR CAVITY 30
AND GROUND. FIG.1
NO
KEY OFF. USING AN OHMMETER, REPAIR SHORT TO
DISCONNECT THE BCM MEASURE RESISTANCE IS THE RESISTANCE YES GROUND ON THE
HARNESS BETWEEN ECM HARNESS BELOW 5.0 OHMS? SPEED CONTROL LAMP
CONNECTORS.** CONNECTOR CAVITY 30 CONTROL CIRCUIT.*
AND GROUND. FIG.1
NO
USING AN OHMMETER
MEASURE THE SPEED IS THE RESISTANCE YES REPAIR OPEN SPEED
CONTROL LAMP ABOVE 5.0 OHMS? CONTROL LAMP
CONTROL CIRCUIT. CONTROL CIRCUIT.*
FIG.2
NO
REPLACE THE BODY
CONTROL MODULE.*
S
P
E
E
D
C
O
N
T
R
O
L
T
E
S
T
S
391
ProCarManuals.com

TEST NS-SELNO START SELECTION MENU
NOTE:The battery must be fully charged before performing any test in this manual.
NOTE:If the engine will not crank or cranks but will not run, be sure to check the Sentry Key
Immobilizer Module (SKIM) for proper communication and trouble codes.
NOTE:With the DRB, attempt to read ECM trouble codes. If the DRB is unable to communicate with
the ECM, perform test NS-2A. If there are any trouble codes present they must be repaired before
continuing with the No Start Symptom diagnostics.
Below you will find a recommended procedure to correct a No Start Problem by symptom. They
should be performed in the order that they are listed.
Repairing a No Crank Condition..............................................NS-1A
Repairing a No Response Condition...........................................NS-2A
Repairing a No Start Condition................................................NS-3A
Repairing a Start and Stall Condition...........................................NS-4A
Checking the Engine Mechanical Systems......................................NS-5A
NOTE:A failed engine coolant temperature (ECT) sensor can cause a cranks but will not run or an
extended cranking before starting condition. This occurs when the ECT sensor calibration fails
(sensor indicates engine temp is warmer than actual engine temp) and the ECM cannot command
proper fuel quantity to the injection pump.
NOTE:For all component locations seeGeneral Information Section 4.0 in this manual.
N
O
S
T
A
R
T
T
E
S
T
S
392
ProCarManuals.com