wheel alignment CHRYSLER CARAVAN 2003 Owner's Guide

INSTALLATION
NOTE: If new hinge pins are to be used, verify that
the knurling on the hinge pin is aligned with the
knurling on in the door hinge prior to driving in the
pin. Also, verify that the hinge pin is fully seated to
the door hinge and a new retaining clip is installed.
(1) Support door on suitable lifting device.
(2) Position door to vehicle. Verify net pierce nub-
bin is engaged if reusing original hinges.
(3) Steady door on lifting device and install bolts
attaching upper hinge to door end frame. Tighten
bolts to 34 N´m (25 ft. lbs.) torque.
(4) Install bolts attaching door check strap to
A-pillar. Tighten bolts to 12 N´m (105 in. lbs.) torque.
(5) Install bolts attaching lower hinge to door end
frame. Tighten bolts to 34 N´m (25 ft. lbs.) torque.
Align door to achieve equal spacing to surrounding
body panels. Panels should be flush across all gaps.
(6) Connect door harness into body wiring harness.
(7) Connect positive lock slide on the side of the
wire connectors.
(8) Connect clips attaching door harness wire con-
nector to inner fender brace.
(9) Install front wheelhouse splash shield.
(10) Verify door operation and alignment. Adjust
as necessary.
Fig. 3 FRONT DOOR WIRE CONNECTORS
1 - LOCK TAB
2 - POSITIVE LOCK
3 - BODY HARNESS CONNECTOR
4 - FRONT FENDER
5 - DOOR HARNESS CONNECTOR
6 - BODY HARNESS
Fig. 4 FRONT DOOR - HINGE PIN REMOVAL
1 - FRONT DOOR
2 - CLIP
3 - A-PILLAR
4 - HINGE PIN
5 - CLIP
6 - DOOR CHECK STRAP
Fig. 5 FRONT DOOR - HINGE BOLT REMOVAL
1 - FRONT DOOR
2 - UPPER HINGE
3 - CHECK STRAP
4 - LOWER HINGE
23 - 16 DOOR - FRONTRS
DOOR (Continued)
ProCarManuals.com

(3) Align with paint breaks around bolt heads.
(4) Install bolts attaching ends of crossmember to
radiator closure panel (Fig. 14). Tighten bolts to 19
N´m (14 ft. lbs.) torque.
(5) Install bolts attaching radiator isolators to
crossmember.
(6) Install screw attaching coolant recovery bottle
to crossmember.
(7) Install bolt attaching air cleaner housing to
crossmember.
(8) Install engine air inlet resonator.
(9) Install radiator sight shield.
(10) Install hood prop rod.
(11) Align hood latch by placing latch over net
pierce tabs. If alignment is required, flatten tabs.
(12) Install bolts attaching hood latch to cross-
member. Tighten bolts to 13.5 N´m (10 ft. lbs.)
torque.
(13) Verify hood latch operation and hood align-
ment.
FRONT WHEELHOUSE
SPLASH SHIELD
REMOVAL
(1) Hoist and support vehicle on safety stands.
(Refer to LUBRICATION & MAINTENANCE/HOIST-
ING - STANDARD PROCEDURE).
(2) Remove front wheel.
(3) Remove push pin fasteners attaching splash
shield to frame rail forward of suspension.
(4) Remove push pin fasteners attaching splash
shield to frame rail rearward of suspension.
(5) Remove screws attaching wheelhouse splash
shield to front fender and front bumper fascia.
(6) Remove splash shield from vehicle (Fig. 15).
INSTALLATION
(1) Place splash shield in position on vehicle (Fig.
15).
(2) Install push pin fasteners attaching splash
shield to frame rail forward of suspension.
(3) Install push pin fasteners attaching splash
shield to frame rail rearward of suspension.
(4) Install screws attaching wheelhouse splash
shield to front fender.
(5) Install front wheel.
(6) Lower vehicle.
LUGGAGE RACK RISER
REMOVAL
(1) Remove two fasteners from the front riser.
Gently pull up on the luggage rack side rail and
detach the riser snap to remove riser from the rail
(Fig. 16).
(2) Repeat for the opposite side, if necessary.
(3) Remove front riser(s) from vehicle (Fig. 17).
Fig. 15 FRONT WHEELHOUSE SPLASH SHIELD
1 - FRONT FENDER WHEELHOUSE SPLASH SHIELD
2 - PUSH PIN FASTENERS
3 - ACCESSORY DRIVE SPLASH SHIELD
4 - SCREWS
Fig. 16 LUGGAGE RACK RISER COVER
1 - FRONT RISER COVER
2 - LOCK TABS
3 - LUGGAGE RACK SIDE RAIL
4 - FRONT RISER
23 - 54 EXTERIORRS
GRILLE OPENING REINFORCEMENT (Continued)
ProCarManuals.com

ABS FASTENER TORQUE,
SPECIFICATIONS......................5-79
ABSORBER - DESCRIPTION, SHOCK.......2-36
ABSORBER - INSTALLATION, SHOCK......2-38
ABSORBER - OPERATION, SHOCK........2-36
ABSORBER - REMOVAL, SHOCK..........2-36
ABSORBER (UPPER BUSHING) -
ASSEMBLY, SHOCK....................2-37
ABSORBER (UPPER BUSHING) -
DISASSEMBLY, SHOCK.................2-36
A/C COMPRESSOR - DESCRIPTION......24-63
A/C COMPRESSOR - OPERATION........24-63
A/C COOL DOWN TEST - DIAGNOSIS
AND TESTING........................24-4
A/C DISTRIBUTION DUCT -
INSTALLATION.......................24-53
A/C DISTRIBUTION DUCT - REMOVAL....24-53
A/C HEATER CONTROL - INSTALLATION....24-9
A/C HEATER CONTROL - REMOVAL.......24-9
A/C PERFORMANCE TEST - DIAGNOSIS
AND TESTING........................24-5
A/C PLUMBING - CAUTION.............24-61
A/C PLUMBING - WARNING............24-61
A/C PRESSURE TRANSDUCER -
DESCRIPTION.......................24-10
A/C PRESSURE TRANSDUCER -
DIAGNOSIS AND TESTING.............24-10
A/C PRESSURE TRANSDUCER -
INSTALLATION.......................24-11
A/C PRESSURE TRANSDUCER -
OPERATION.........................24-10
A/C PRESSURE TRANSDUCER -
REMOVAL..........................24-10
ACCELERATOR PEDAL - INSTALLATION . . . 14-24
ACCELERATOR PEDAL - REMOVAL.......14-23
ACCESSORY DRIVE BELT - DIAGNOSIS
AND TESTING.........................7-7
ACCESSORY DRIVE BELT TENSION,
SPECIFICATIONS.......................7-5
ACCESSORY RELAY - DESCRIPTION . . . 8W-97-2
ACCESSORY RELAY - DIAGNOSIS &
TESTING.........................8W-97-2
ACCESSORY RELAY - OPERATION.....8W-97-2
ACCUMULATOR - DESCRIPTION........21-188
ACCUMULATOR - OPERATION..........21-189
A/C-HEATER CONTROL - INSTALLATION . . . 24-29
A/C-HEATER CONTROL - REMOVAL......24-29
ACTUATOR - DESCRIPTION, BLEND
DOOR........................24-11,24-30
ACTUATOR - DESCRIPTION, ENGAGE.....8N-10
ACTUATOR - DESCRIPTION, LATCH......8N-14
ACTUATOR - DESCRIPTION, MODE
DOOR.............................24-24
ACTUATOR - DESCRIPTION,
RECIRCULATION DOOR................24-27
ACTUATOR - INSTALLATION, BLEND
DOOR........................24-12,24-31
ACTUATOR - INSTALLATION, ENGAGE....8N-11
ACTUATOR - INSTALLATION, LATCH.....8N-14
ACTUATOR - INSTALLATION, MODE
DOOR........................24-25,24-36
ACTUATOR - INSTALLATION,
RECIRCULATION DOOR................24-28
ACTUATOR - OPERATION, BLEND DOOR . . 24-11,
24-30
ACTUATOR - OPERATION, ENGAGE......8N-11
ACTUATOR - OPERATION, LATCH........8N-14
ACTUATOR - OPERATION, MODE DOOR . . . 24-24
ACTUATOR - OPERATION,
RECIRCULATION DOOR................24-27
ACTUATOR - REMOVAL, BLEND DOOR . . . 24-12,
24-31
ACTUATOR - REMOVAL, ENGAGE........8N-11
ACTUATOR - REMOVAL, LATCH.........8N-14
ACTUATOR - REMOVAL, MODE DOOR....24-25,
24-36
ACTUATOR - REMOVAL, RECIRCULATION
DOOR.............................24-27
ADAPTER - INSTALLATION, FRONT DISC
BRAKE CALIPER......................5-31
ADAPTER - INSTALLATION, OIL FILTER
. . . 9-139
ADAPTER - REMOVAL, FRONT DISC
BRAKE CALIPER
......................5-31
ADAPTER - REMOVAL, OIL FILTER
.......9-139
ADAPTIVE MEMORIES, OPERATION -
FUEL CORRECTION OR
................14-20
ADDING ADDITIONAL COOLANT -
STANDARD PROCEDURE
.................7-5ADDITIONAL COOLANT - STANDARD
PROCEDURE, ADDING...................7-5
ADHESIVE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-50
ADHESIVE ATTACHED - REMOVAL,
EXTERIOR NAME PLATES..............23-50
ADHESIVE LOCATIONS -
SPECIFICATIONS, STRUCTURAL........23-153
ADJUSTER-BORC-PILLAR -
INSTALLATION, SEAT BELT HEIGHT......8O-12
ADJUSTER-BORC-PILLAR -
REMOVAL, SEAT BELT HEIGHT..........8O-12
ADJUSTER - DIAGNOSIS AND TESTING,
DRUM BRAKE AUTOMATIC..............5-13
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK MANUAL................23-94
ADJUSTER - INSTALLATION, FRONT
SEAT TRACK POWER.................23-94
ADJUSTER - REMOVAL, FRONT SEAT
TRACK MANUAL.....................23-94
ADJUSTER - REMOVAL, FRONT SEAT
TRACK POWER......................23-94
ADJUSTER KNOB - INSTALLATION, SEAT
BELT HEIGHT.......................8O-13
ADJUSTER KNOB - REMOVAL, SEAT
BELT HEIGHT.......................8O-13
ADJUSTER NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING, HYDRAULIC
LASH...............................9-34
ADJUSTER TENSION RELEASE -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC....................5-58
ADJUSTER TENSION RESET -
STANDARD PROCEDURE, PARKING
BRAKE AUTOMATIC.....................5-59
ADJUSTERS - INSTALLATION,
HYDRAULIC LASH.....................9-34
ADJUSTERS - REMOVAL, HYDRAULIC
LASH...............................9-34
AERATION - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-3
AFTER AN AIRBAG DEPLOYMENT -
STANDARD PROCEDURE, SERVICE.......8O-3
AIR CLEANER ELEMENT - INSTALLATION . . 9-24,
9-98
AIR CLEANER ELEMENT - REMOVAL . . 9-24,9-98
AIR CLEANER HOUSING - INSTALLATION . . 9-24,
9-99
AIR CLEANER HOUSING - REMOVAL . . 9-24,9-99
AIR CONDITIONING LINES -
INSTALLATION, REAR................24-105
AIR CONDITIONING LINES - REMOVAL,
REAR.............................24-104
AIR CONTROL MOTOR - DESCRIPTION,
IDLE...............................14-28
AIR CONTROL MOTOR - INSTALLATION,
IDLE...............................14-29
AIR CONTROL MOTOR - OPERATION,
IDLE...............................14-28
AIR CONTROL MOTOR - REMOVAL, IDLE . . 14-29
AIR EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER..............23-56
AIR EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER..............23-57
AIR EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER..............23-56
AIR FILTER - DESCRIPTION............24-39
AIR FILTER - INSTALLATION............24-40
AIR FILTER - REMOVAL...............24-39
AIR GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH...............24-17
AIR GAP, SPECIFICATIONS - WHEEL
SPEED SENSOR.......................5-79
AIR INTAKE PIPE - INSTALLATION......24-113
AIR INTAKE PIPE - REMOVAL..........24-112
AIR OUTLETS - DESCRIPTION.....24-40,24-52
AIR OUTLETS - INSTALLATION..........24-52
AIR OUTLETS - REMOVAL.............24-52
AIR PRESSURE TESTS - DIAGNOSIS
AND TESTING, CLUTCH...............21-122
AIR TEMPERATURE SENSOR -
DESCRIPTION, INLET.................14-29
AIR TEMPERATURE SENSOR -
OPERATION, INLET
...................14-29
AIRBAG - DESCRIPTION, DRIVER
........8O-5
AIRBAG - DESCRIPTION, PASSENGER
.....8O-7
AIRBAG - DESCRIPTION, SEAT
..........8O-10
AIRBAG - INSTALLATION, DRIVER
........8O-6AIRBAG - INSTALLATION, PASSENGER....8O-9
AIRBAG - OPERATION, DRIVER..........8O-5
AIRBAG - OPERATION, PASSENGER.......8O-8
AIRBAG - OPERATION, SEAT...........8O-11
AIRBAG - REMOVAL, DRIVER............8O-5
AIRBAG - REMOVAL, PASSENGER........8O-8
AIRBAG CONTROL MODULE -
DESCRIPTION, SIDE IMPACT...........8O-17
AIRBAG CONTROL MODULE -
INSTALLATION, SIDE IMPACT...........8O-17
AIRBAG CONTROL MODULE -
OPERATION, SIDE IMPACT.............8O-17
AIRBAG CONTROL MODULE - REMOVAL,
SIDE IMPACT.......................8O-17
AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER AN........8O-3
AIRBAG SYSTEM - DIAGNOSIS AND
TESTING............................8O-2
AIRBAG TRIM COVER - INSTALLATION,
DRIVER.............................8O-7
AIRBAG TRIM COVER - REMOVAL,
DRIVER.............................8O-6
AIRBAGS - STANDARD PROCEDURE,
HANDLING..........................8O-3
AJAR SWITCH - EXPORT -
INSTALLATION, HOOD.................8Q-3
AJAR SWITCH - EXPORT - REMOVAL,
HOOD..............................8Q-3
ALIGNMENT - DESCRIPTION, WHEEL......2-46
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, FRONT FOG LAMP UNIT.....8L-9
ALIGNMENT - EXPORT - STANDARD
PROCEDURE, HEADLAMP UNIT.........8L-17
ALIGNMENT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT................8L-9
ALIGNMENT - STANDARD PROCEDURE,
FRONT WIPER ARM...................8R-8
ALIGNMENT - STANDARD PROCEDURE,
HEADLAMP UNIT.....................8L-17
ALIGNMENT - STANDARD PROCEDURE,
WHEEL.............................2-51
ALIGNMENT, SPECIFICATIONS - WHEEL....2-55
ALUMINUM WHEEL CARE - CLEANING . . . 22-18
AMBIENT TEMP SENSOR - DESCRIPTION . 8M-11
AMBIENT TEMP SENSOR - OPERATION . . 8M-11
AMBIENT TEMPERATURE SENSOR -
DIAGNOSIS AND TESTING.............8M-12
AMBIENT TEMPERATURE SENSOR
CIRCUIT - DIAGNOSIS AND TESTING....8M-12
AN AIRBAG DEPLOYMENT - STANDARD
PROCEDURE, SERVICE AFTER...........8O-3
ANTENNA - EXPORT - DESCRIPTION,
QUARTER GLASS INTEGRAL............8A-9
ANTENNA - EXPORT - DIAGNOSIS AND
TESTING, QUARTER GLASS INTEGRAL....8A-9
ANTENNA - EXPORT - OPERATION,
QUARTER GLASS INTEGRAL............8A-9
ANTENNA BODY AND CABLE -
DESCRIPTION........................8A-4
ANTENNA BODY AND CABLE -
DIAGNOSIS AND TESTING..............8A-4
ANTENNA BODY AND CABLE -
INSTALLATION.......................8A-6
ANTENNA BODY AND CABLE -
OPERATION..........................8A-4
ANTENNA BODY AND CABLE - REMOVAL . . 8A-5
ANTENNA CABLE - INSTALLATION,
INSTRUMENT PANEL..................8A-9
ANTENNA CABLE - REMOVAL,
INSTRUMENT PANEL..................8A-8
ANTENNA MODULE - EXPORT -
DESCRIPTION........................8A-6
ANTENNA MODULE - EXPORT -
DIAGNOSIS AND TESTING..............8A-7
ANTENNA MODULE - EXPORT -
INSTALLATION.......................8A-7
ANTENNA MODULE - EXPORT -
OPERATION..........................8A-6
ANTENNA MODULE - EXPORT -
REMOVAL
...........................8A-7
ANTILOCK BRAKE - DESCRIPTION,
CONTROLLER
........................8E-5
ANTILOCK BRAKE - INSTALLATION,
CONTROLLER
........................8E-6
ANTILOCK BRAKE - OPERATION,
CONTROLLER
........................8E-5
ANTILOCK BRAKE - REMOVAL,
CONTROLLER
........................8E-6
RSINDEX1
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

ANTILOCK BRAKE SYSTEM -
DESCRIPTION........................5-75
ANTILOCK BRAKE SYSTEM - OPERATION . . 5-76
ANTILOCK BRAKE SYSTEM BLEEDING -
STANDARD PROCEDURE................5-78
ANTILOCK BRAKE SYSTEM (EXPORT) -
DESCRIPTION........................5-75
A-PILLAR LOWER EXTENSION TRIM -
INSTALLATION.......................23-73
A-PILLAR LOWER EXTENSION TRIM -
REMOVAL..........................23-73
A-PILLAR TRIM - INSTALLATION........23-73
A-PILLAR TRIM - REMOVAL............23-73
A-PILLAR-HEADER, OR B-PILLAR -
INSTALLATION.......................23-17
A-PILLAR-HEADER, OR B-PILLAR -
REMOVAL..........................23-17
APPLIQUE - INSTALLATION.............23-14
APPLIQUE - REMOVAL................23-14
ARM - DESCRIPTION, LOWER CONTROL . . . 2-12
ARM - INSPECTION, LOWER CONTROL....2-14
ARM - INSTALLATION, LOWER CONTROL . . 2-15
ARM - INSTALLATION, REAR WIPER.....8R-14
ARM - INSTALLATION, TORQUE..........3-44
ARM - OPERATION, LOWER CONTROL.....2-12
ARM - REMOVAL, LOWER CONTROL......2-12
ARM - REMOVAL, REAR WIPER.........8R-14
ARM - REMOVAL, TORQUE..............3-44
ARM ALIGNMENT - STANDARD
PROCEDURE, FRONT WIPER............8R-8
ARM (REAR BUSHING - HYDRO) -
ASSEMBLY, LOWER CONTROL...........2-14
ARM (REAR BUSHING - HYDRO) -
DISASSEMBLY, LOWER CONTROL........2-14
ARM (REAR BUSHING - STANDARD) -
ASSEMBLY, LOWER CONTROL...........2-14
ARM (REAR BUSHING - STANDARD) -
DISASSEMBLY, LOWER CONTROL........2-13
ARMREST - INSTALLATION.............23-90
ARMREST - REMOVAL................23-90
ARMS - DESCRIPTION, ROCKER........9-109
ARMS - INSPECTION, ROCKER...........9-35
ARMS - INSTALLATION, FRONT WIPER....8R-9
ARMS - INSTALLATION, ROCKER.........9-35
ARMS - OPERATION, ROCKER..........9-109
ARMS - REMOVAL, FRONT WIPER........8R-9
ARMS - REMOVAL, ROCKER.............9-34
ARMS AND SHAFT - ASSEMBLY,
ROCKER............................9-109
ARMS AND SHAFT - DISASSEMBLY,
ROCKER............................9-109
ARMS AND SHAFT - INSTALLATION,
ROCKER............................9-110
ARMS AND SHAFT - REMOVAL, ROCKER . . 9-109
ASSIST HANDLE - INSTALLATION........23-73
ASSIST HANDLE - REMOVAL...........23-73
ASSIST STRAP - INSTALLATION, FRONT
SEATBACK..........................23-91
ASSIST STRAP - REMOVAL, FRONT
SEATBACK..........................23-91
ATC - OPERATION, THREE ZONE.........24-3
ATC - OPERATION, TWO ZONE.........24-106
ATTACHED - INSTALLATION, EXTERIOR
NAME PLATES - ADHESIVE.............23-50
ATTACHED - INSTALLATION, EXTERIOR
NAME PLATES - TAPE.................23-50
ATTACHED - REMOVAL, EXTERIOR NAME
PLATES - ADHESIVE..................23-50
ATTACHED - REMOVAL, EXTERIOR NAME
PLATES - TAPE ......................23-50
AUDIO - DIAGNOSIS AND TESTING.......8A-2
AUDIO/VIDEO - DESCRIPTION...........8A-1
AUDIO/VIDEO - OPERATION.............8A-2
AUTO SHUT DOWN RELAY -
DESCRIPTION.........................8I-3
AUTO SHUT DOWN RELAY - OPERATION . . . 8I-3
AUTOMATIC ADJUSTER - DIAGNOSIS
AND TESTING, DRUM BRAKE
............5-13
AUTOMATIC ADJUSTER TENSION
RELEASE - STANDARD PROCEDURE,
PARKING BRAKE
......................5-58
AUTOMATIC ADJUSTER TENSION RESET
- STANDARD PROCEDURE, PARKING
BRAKE
..............................5-59
AUTOMATIC DAY / NIGHT MIRROR -
DESCRIPTION
.......................8N-47
AUTOMATIC DAY / NIGHT MIRROR -
DIAGNOSIS AND TESTING
.............8N-47AUTOMATIC DAY / NIGHT MIRROR -
OPERATION.........................8N-47
AUTOMATIC TEMPERATURE CONTROL -
DESCRIPTION........................24-2
AUTOMATIC TRANSAXLE -
DESCRIPTION, 41TE.................21-117
AUTOMATIC TRANSAXLE - OPERATION,
41TE.............................21-119
AUTOMATIC TRANSAXLE, SPECIAL
TOOLS - 41TE......................21-183
AUTOSTICK SWITCH - DESCRIPTION....21-189
AUTOSTICK SWITCH - OPERATION......21-189
AWD - INSTALLATION..............2-39,2-44
AWD - INSTALLATION, REAR WHEEL
SPEED SENSOR.......................5-80
AWD - REMOVAL.................2-38,2-44
AWD - REMOVAL, REAR WHEEL SPEED
SENSOR............................5-80
AWD AND HEAVY DUTY - INSTALLATION . . . 2-35
AWD AND HEAVY DUTY - REMOVAL......2-35
AXLE SEALS - INSTALLATION...........21-61
AXLE SEALS - REMOVAL..............21-61
B OR C-PILLAR - INSTALLATION, SEAT
BELT HEIGHT ADJUSTER..............8O-12
B OR C-PILLAR - REMOVAL, SEAT BELT
HEIGHT ADJUSTER...................8O-12
BACK - INSTALLATION, BENCH SEAT....23-101
BACK - QUAD BUCKET - INSTALLATION,
BUCKET SEAT.......................23-97
BACK - QUAD BUCKET - REMOVAL,
BUCKET SEAT.........................23-97
BACK - REMOVAL, BENCH SEAT........23-101
BACK COVER - INSTALLATION, BENCH
SEAT .............................23-102
BACK COVER - REMOVAL, BENCH SEAT . . 23-102
BACK HINGE - REMOVAL, BENCH SEAT . . 23-100
BACK HINGE COVERS - QUAD BUCKET,
50/50 SPLIT, BENCH - INSTALLATION,
SEAT .............................23-100
BACK HINGE COVERS - QUAD BUCKET,
50/50 SPLIT, BENCH - REMOVAL, SEAT . . 23-100
BACKING PLATE - INSTALLATION,
STEERING COLUMN COVER............23-69
BACKING PLATE - REMOVAL, STEERING
COLUMN COVER.....................23-69
BACK-UP LAMP SWITCH -
INSTALLATION.......................21-62
BACK-UP LAMP SWITCH - REMOVAL.....21-62
BAG RETAINER - INSTALLATION,
PLASTIC GROCERY..................23-103
BAG RETAINER - REMOVAL, PLASTIC
GROCERY.........................23-103
BALANCE - STANDARD PROCEDURE,
TIRE AND WHEEL.....................22-5
BALANCE SHAFTS AND CARRIER
ASSEMBLY - DESCRIPTION.............9-69
BALANCE SHAFTS AND CARRIER
ASSEMBLY - INSTALLATION.............9-72
BALANCE SHAFTS AND CARRIER
ASSEMBLY - OPERATION...............9-69
BALANCE SHAFTS AND CARRIER
ASSEMBLY - REMOVAL.................9-69
BALL BEARING - INSTALLATION, END
COVER.............................21-10
BALL BEARING - REMOVAL, END COVER . . . 21-9
BALL JOINT - DESCRIPTION, LOWER......2-10
BALL JOINT - DIAGNOSIS AND TESTING,
LOWER.............................2-10
BALL JOINT - OPERATION, LOWER.......2-10
BALL JOINT SEAL BOOT - INSTALLATION . . 2-11
BALL JOINT SEAL BOOT - REMOVAL......2-11
BAR - DESCRIPTION, STABILIZER....2-16,2-43
BAR - DESCRIPTION, TRACK............2-44
BAR - INSPECTION, STABILIZER..........2-17
BAR - INSTALLATION, STABILIZER........2-17
BAR - INSTALLATION, TRACK............2-45
BAR - OPERATION, STABILIZER......2-16,2-44
BAR - OPERATION, TRACK..............2-44
BAR - REMOVAL, STABILIZER...........2-17
BAR - REMOVAL, TRACK...............2-44
BAR CUSHION - INSTALLATION,
STABILIZER
...........................2-4
BAR CUSHION - REMOVAL, STABILIZER
....2-4
BASE BRAKE BLEEDING - STANDARD
PROCEDURE
..........................5-7
BASE BRAKE SYSTEM - DIAGNOSIS AND
TESTING
.............................5-4
BASE BRAKE SYSTEM, SPECIAL TOOLS
....5-10BASE BRAKES - DESCRIPTION............5-3
BASE BRAKES - OPERATION..............5-3
BASE BRAKES (EXPORT) - DESCRIPTION . . . 5-3
BASE COAT/CLEARCOAT FINISH -
DESCRIPTION.......................23-84
BATTERY - DESCRIPTION...............8F-7
BATTERY - DIAGNOSIS AND TESTING.....8F-9
BATTERY - OPERATION.................8F-9
BATTERY - REMOVAL.................8F-15
BATTERY CABLE - DIAGNOSIS AND
TESTING...........................8F-16
BATTERY CABLES - DESCRIPTION.......8F-16
BATTERY CABLES - INSTALLATION.......8F-18
BATTERY CABLES - OPERATION.........8F-16
BATTERY CABLES - REMOVAL..........8F-18
BATTERY CHARGING - STANDARD
PROCEDURE, CONVENTIONAL..........8F-11
BATTERY CHARGING - STANDARD
PROCEDURE, SPIRAL PLATE............8F-10
BATTERY ELECTROLYTE LEVEL -
STANDARD PROCEDURE, CHECKING.....8F-14
BATTERY HOLDDOWN - DESCRIPTION....8F-15
BATTERY HOLDDOWN - INSTALLATION . . . 8F-16
BATTERY HOLDDOWN - OPERATION.....8F-15
BATTERY HOLDDOWN - REMOVAL.......8F-16
BATTERY REPLACEMENT - STANDARD
PROCEDURE........................8N-42
BATTERY, SPECIFICATIONS.............8N-43
BATTERY SYSTEM - CLEANING...........8F-5
BATTERY SYSTEM - DESCRIPTION........8F-1
BATTERY SYSTEM - DIAGNOSIS AND
TESTING............................8F-2
BATTERY SYSTEM - INSPECTION.........8F-5
BATTERY SYSTEM - OPERATION.........8F-2
BATTERY SYSTEM - SPECIFICATIONS......8F-6
BATTERY SYSTEM SPECIAL TOOLS,
SPECIAL TOOLS......................8F-7
BATTERY TEMPERATURE SENSOR -
DESCRIPTION.......................8F-23
BATTERY TEMPERATURE SENSOR -
OPERATION.........................8F-23
BATTERY TEMPERATURE SENSOR -
REMOVAL..........................8F-23
BATTERY TEMPERATURE SENSOR -
SPECIFICATIONS.....................8F-22
BATTERY TRAY - DESCRIPTION.........8F-18
BATTERY TRAY - INSTALLATION.........8F-19
BATTERY TRAY - OPERATION...........8F-19
BATTERY TRAY - REMOVAL............8F-19
BEARING - DESCRIPTION, HUB.......2-30,2-5
BEARING - DIAGNOSIS AND TESTING,
HUB.............................2-30,2-5
BEARING - INSTALLATION, CLUTCH
RELEASE LEVER.......................6-7
BEARING - INSTALLATION, END COVER
BALL..............................21-10
BEARING - INSTALLATION, HUB.......2-32,2-5
BEARING - OPERATION, HUB.........2-30,2-5
BEARING - REMOVAL, CLUTCH RELEASE
LEVER...............................6-6
BEARING - REMOVAL, END COVER BALL . . . 21-9
BEARING - REMOVAL, HUB..........2-31,2-5
BEARING CLEARANCE - STANDARD
PROCEDURE, MEASURING
CONNECTING ROD...................9-120
BEARING CLEARANCE USING
PLASTIGAGE - STANDARD
PROCEDURE, MEASURING..........9-12,9-84
BEARING FITTING - STANDARD
PROCEDURE, MAIN...................9-123
BEARING PRELOAD - ADJUSTMENT,
DIFFERENTIAL......................21-199
BEARINGS - INSTALLATION,
CRANKSHAFT MAIN..................9-124
BEARINGS - REMOVAL, CRANKSHAFT
MAIN..............................9-124
BEARINGS (IN BLOCK) - DESCRIPTION,
CAMSHAFT.........................9-115
BEARINGS (IN BLOCK) - INSPECTION,
CAMSHAFT.........................9-115
BEARINGS (IN BLOCK) - INSTALLATION,
CAMSHAFT
.........................9-115
BEARINGS (IN BLOCK) - OPERATION,
CAMSHAFT
.........................9-115
BEARINGS (IN BLOCK) - REMOVAL,
CAMSHAFT
.........................9-115
BELLCRANK - INSTALLATION
...........23-34
BELLCRANK - REMOVAL
...............23-34
2 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

FLANGE SHIM SELECTION,
ADJUSTMENTS - OUTPUT...............21-7
FLEX DRIVE - DESCRIPTION...........8N-36
FLEX DRIVE - INSTALLATION...........8N-37
FLEX DRIVE - OPERATION.............8N-36
FLEX DRIVE - REMOVAL...............8N-37
FLEX PLATE - INSTALLATION...........9-131
FLEX PLATE - REMOVAL...............9-131
FLEXIBLE FUEL ENGINE OIL -
DESCRIPTION.........................0-3
FLOOR CONSOLE TRAY - BRACKET
ASSEMBLY - INSTALLATION............23-82
FLOOR CONSOLE TRAY - BRACKET
ASSEMBLY - REMOVAL................23-82
FLOOR CONSOLE TRAY - INSTALLATION . . 23-81
FLOOR CONSOLE TRAY - REMOVAL......23-81
FLOOR DISTRIBUTION DUCTS -
INSTALLATION.......................24-49
FLOOR DISTRIBUTION DUCTS -
REMOVAL..........................24-48
FLOOR MATS - INSTALLATION, CARPETS . 23-75
FLOOR MATS - REMOVAL, CARPETS.....23-74
FLOW AND PRESSURE TEST -
DIAGNOSIS AND TESTING, POWER
STEERING SYSTEM....................19-1
FLOW CHECK - DIAGNOSIS AND
TESTING, COOLING SYSTEM.............7-3
FLUID - DESCRIPTION, TRANSMISSION.....0-4
FLUID AND FILTER SERVICE -
STANDARD PROCEDURE..............21-203
FLUID CAPACITIES - SPECIFICATIONS......0-6
FLUID CHANGE - STANDARD
PROCEDURE, DIFFERENTIAL
ASSEMBLY..........................3-40
FLUID CHANGE - STANDARD
PROCEDURE, OVERRUNNING CLUTCH
HOUSING............................3-41
FLUID CHANGE - STANDARD
PROCEDURE, PTU.....................21-5
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-32
FLUID COOLER - DESCRIPTION.........19-44
FLUID COOLER - INSTALLATION.........19-45
FLUID COOLER - OPERATION...........19-44
FLUID COOLER - REMOVAL............19-44
FLUID DRAIN AND FILL - STANDARD
PROCEDURE........................21-71
FLUID FILL/CHECK LOCATIONS -
DESCRIPTION.........................0-7
FLUID LEAK DIAGNOSIS, DIAGNOSIS
AND TESTING........................21-3
FLUID LEAKAGE - DIAGNOSIS AND
TESTING, TORQUE CONVERTER
HOUSING..........................21-123
FLUID LEVEL AND CONDITION CHECK,
STANDARD PROCEDURE..............21-201
FLUID LEVEL CHECK - STANDARD
PROCEDURE........................21-71
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, BRAKE...................5-32
FLUID LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING........19-44
FLUID LEVEL INSPECTION - STANDARD
PROCEDURE.........................21-4
FLUID LEVEL SWITCH - DESCRIPTION,
BRAKE
..............................5-10
FLUID LEVEL SWITCH - INSTALLATION,
BRAKE
..............................5-11
FLUID LEVEL SWITCH - INSTALLATION,
WASHER
...........................8R-16
FLUID LEVEL SWITCH - OPERATION,
BRAKE
..............................5-10
FLUID LEVEL SWITCH - REMOVAL,
BRAKE
..............................5-11
FLUID LEVEL SWITCH - REMOVAL,
WASHER
...........................8R-15
FLUID, SPECIFICATIONS - BRAKE
.........5-33
FLUSH MEASUREMENTS -
SPECIFICATIONS, GAP
................23-121
FLYWHEEL - INSTALLATION
.............6-12
FLYWHEEL - REMOVAL
.................6-12
FOG LAMP - DIAGNOSIS AND TESTING,
FRONT
..............................8L-7
FOG LAMP - EXPORT - DESCRIPTION,
REAR
..............................8L-22
FOG LAMP - EXPORT - INSTALLATION,
FRONT
..............................8L-9FOG LAMP - EXPORT - REMOVAL,
FRONT..............................8L-9
FOG LAMP - INSTALLATION, FRONT.......8L-9
FOG LAMP - REMOVAL, FRONT..........8L-9
FOG LAMP UNIT ALIGNMENT - EXPORT
- STANDARD PROCEDURE, FRONT........8L-9
FOG LAMP UNIT ALIGNMENT -
STANDARD PROCEDURE, FRONT.........8L-9
FOLDAWAY MIRROR SWITCH - EXPORT
- DESCRIPTION, POWER..............8N-48
FOLDAWAY MIRROR SWITCH - EXPORT
- INSTALLATION, POWER..............8N-49
FOLDAWAY MIRROR SWITCH - EXPORT
- OPERATION, POWER................8N-48
FOLDAWAY MIRROR SWITCH - EXPORT
- REMOVAL, POWER..................8N-48
FORK AND SHAFT - DESCRIPTION,
SHIFT.............................21-113
FORM-IN-PLACE GASKETS AND
SEALERS - STANDARD PROCEDURE . . 9-11,9-84
FRAME DIMENSIONS, SPECIFICATIONS....13-4
FRONT - DESCRIPTION, HALF SHAFT.......3-1
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL.......................9-127,9-40
FRONT - INSTALLATION, HALF SHAFT......3-4
FRONT - INSTALLATION, SEAT BELT &
RETRACTOR - OUTBOARD.............8O-13
FRONT - INSTALLATION, SPRING
MOUNTS............................2-42
FRONT - INSTALLATION, WHEEL
MOUNTING STUDS...................22-21
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL..........................9-127,9-40
FRONT - REMOVAL, HALF SHAFT..........3-2
FRONT - REMOVAL, SEAT BELT &
RETRACTOR - OUTBOARD.............8O-13
FRONT - REMOVAL, SPRING MOUNTS.....2-42
FRONT - REMOVAL, WHEEL MOUNTING
STUDS.............................22-20
FRONT - SPECIFICATIONS, HALF SHAFT . . . 3-15,
3-6
FRONT BRAKE ROTOR - INSTALLATION....5-54
FRONT BRAKE ROTOR - REMOVAL.......5-54
FRONT BUMPER REINFORCEMENT -
INSTALLATION........................13-2
FRONT BUMPER REINFORCEMENT -
REMOVAL...........................13-2
FRONT BUSHING - INSTALLATION, LEAF
SPRING.............................2-29
FRONT BUSHING - REMOVAL, LEAF
SPRING.............................2-28
FRONT CABLE - INSTALLATION..........5-64
FRONT CABLE - INSTALLATION,
PARKING BRAKE LEVER................5-66
FRONT CABLE - REMOVAL..............5-64
FRONT CABLE - REMOVAL, PARKING
BRAKE LEVER........................5-65
FRONT CONTROL MODULE -
DESCRIPTION........................8E-7
FRONT CONTROL MODULE - DIAGNOSIS
AND TESTING........................8E-7
FRONT CONTROL MODULE -
INSTALLATION........................8E-8
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE - REMOVAL....8E-8
FRONT CRADLE CROSSMEMBER -
DESCRIPTION........................13-9
FRONT CRADLE CROSSMEMBER
THREAD REPAIR - DESCRIPTION.........13-9
FRONT CROSSMEMBER MOUNT
BUSHINGS - INSTALLATION............13-12
FRONT CROSSMEMBER MOUNT
BUSHINGS - REMOVAL................13-12
FRONT DISC BRAKE CALIPER ADAPTER
- INSTALLATION......................5-31
FRONT DISC BRAKE CALIPER ADAPTER
- REMOVAL..........................5-31
FRONT DISC BRAKE CALIPER
(DISC/DISC BRAKES) - INSTALLATION
.....5-27
FRONT DISC BRAKE CALIPER
(DISC/DISC BRAKES) - REMOVAL
.........5-24
FRONT DISC BRAKE CALIPER
(DISC/DRUM BRAKES) -
INSTALLATION
........................5-27
FRONT DISC BRAKE CALIPER
(DISC/DRUM BRAKES) - REMOVAL
.......5-24
FRONT DISC BRAKE SHOES (DISC/DISC
BRAKES) - INSTALLATION
...............5-16FRONT DISC BRAKE SHOES (DISC/DISC
BRAKES) - REMOVAL..................5-14
FRONT DISC BRAKE SHOES (DISC/
DRUM BRAKES) - INSTALLATION.........5-17
FRONT DISC BRAKE SHOES (DISC/
DRUM BRAKES) - REMOVAL............5-15
FRONT DOOR GLASS RUN
WEATHERSTRIP - INSTALLATION.......23-110
FRONT DOOR GLASS RUN
WEATHERSTRIP - REMOVAL...........23-110
FRONT DOOR INNER BELT MOLDING -
INSTALLATION......................23-112
FRONT DOOR INNER BELT MOLDING -
REMOVAL.........................23-112
FRONT DOOR OUTER BELT MOLDING -
INSTALLATION......................23-110
FRONT DOOR OUTER BELT MOLDING -
REMOVAL.........................23-110
FRONT DOOR REAR OUTLET -
INSTALLATION.......................24-42
FRONT DOOR REAR OUTLET - REMOVAL . 24-41
FRONT DOOR WEATHERSTRIP -
INSTALLATION......................23-111
FRONT DOOR WEATHERSTRIP -
REMOVAL.........................23-111
FRONT FASCIA - INSTALLATION..........13-1
FRONT FASCIA - REMOVAL..............13-1
FRONT FENDER - INSTALLATION........23-51
FRONT FENDER - REMOVAL............23-51
FRONT FOG LAMP - DIAGNOSIS AND
TESTING............................8L-7
FRONT FOG LAMP - EXPORT -
INSTALLATION........................8L-9
FRONT FOG LAMP - EXPORT - REMOVAL . . 8L-9
FRONT FOG LAMP - INSTALLATION.......8L-9
FRONT FOG LAMP - REMOVAL...........8L-9
FRONT FOG LAMP UNIT ALIGNMENT -
EXPORT - STANDARD PROCEDURE.......8L-9
FRONT FOG LAMP UNIT ALIGNMENT -
STANDARD PROCEDURE................8L-9
FRONT INBOARD - INSTALLATION, SEAT
BELT BUCKLE.......................8O-11
FRONT INBOARD - REMOVAL, SEAT
BELT BUCKLE.......................8O-11
FRONT MOUNT - INSTALLATION....9-131,9-49
FRONT MOUNT - REMOVAL........9-131,9-49
FRONT POSITION LAMP - EXPORT -
INSTALLATION.......................8L-10
FRONT POSITION LAMP - EXPORT -
REMOVAL..........................8L-10
FRONT SEAT - INSTALLATION...........23-90
FRONT SEAT - REMOVAL..............23-90
FRONT SEAT CUSHION SIDE COVER -
INSTALLATION.......................23-93
FRONT SEAT CUSHION SIDE COVER -
REMOVAL..........................23-93
FRONT SEAT RISER - MANUAL TRACK -
INSTALLATION.......................23-93
FRONT SEAT RISER - MANUAL TRACK -
REMOVAL..........................23-93
FRONT SEAT TRACK - REAR COVER -
INSTALLATION.......................23-95
FRONT SEAT TRACK - REAR COVER -
REMOVAL..........................23-95
FRONT SEAT TRACK MANUAL
ADJUSTER - INSTALLATION............23-94
FRONT SEAT TRACK MANUAL
ADJUSTER - REMOVAL................23-94
FRONT SEAT TRACK POWER ADJUSTER
- INSTALLATION.....................23-94
FRONT SEAT TRACK POWER ADJUSTER
- REMOVAL.........................23-94
FRONT SEATBACK - INSTALLATION......23-91
FRONT SEATBACK - REMOVAL..........23-91
FRONT SEATBACK ASSIST STRAP -
INSTALLATION.......................23-91
FRONT SEATBACK ASSIST STRAP -
REMOVAL..........................23-91
FRONT SEATBACK COVER -
INSTALLATION.......................23-92
FRONT SEATBACK COVER - REMOVAL....23-92
FRONT SEATBACK PANEL -
INSTALLATION
.......................23-92
FRONT SEATBACK PANEL - REMOVAL
....23-91
FRONT SUSPENSION - DESCRIPTION
......2-2
FRONT SUSPENSION - OPERATION
........2-2
FRONT SUSPENSION FASTENER
TORQUE, SPECIFICATIONS
...............2-3
RSINDEX13
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

FRONT SUSPENSION, SPECIAL TOOLS.....2-3
FRONT WASHER PUMP MOTOR -
INSTALLATION.......................8R-8
FRONT WASHER PUMP MOTOR -
REMOVAL...........................8R-8
FRONT WHEEL SPEED SENSOR -
INSTALLATION........................5-80
FRONT WHEEL SPEED SENSOR -
REMOVAL...........................5-79
FRONT WHEELHOUSE SPLASH SHIELD -
INSTALLATION.......................23-54
FRONT WHEELHOUSE SPLASH SHIELD -
REMOVAL..........................23-54
FRONT WIPER ARM ALIGNMENT -
STANDARD PROCEDURE...............8R-8
FRONT WIPER ARMS - INSTALLATION....8R-9
FRONT WIPER ARMS - REMOVAL........8R-9
FRONT WIPER MOTOR - INSTALLATION . . . 8R-9
FRONT WIPER MOTOR - REMOVAL.......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS
AND TESTING........................8R-2
FRONT WIPER/WASHER SWITCH -
DIAGNOSIS AND TESTING..............8R-2
FRONT/QUAD SEAT CUSHION -
INSTALLATION.......................23-92
FRONT/QUAD SEAT CUSHION -
REMOVAL..........................23-92
FRONT-WHEEL-DRIVE - INSTALLATION....2-36
FRONT-WHEEL-DRIVE - REMOVAL........2-35
FUEL CORRECTION OR ADAPTIVE
MEMORIES, OPERATION...............14-20
FUEL DELIVERY SYSTEM - DIAGNOSIS
AND TESTING........................14-2
FUEL DOSING PUMP - DESCRIPTION....24-108
FUEL DOSING PUMP - INSTALLATION . . . 24-108
FUEL DOSING PUMP - OPERATION.....24-108
FUEL DOSING PUMP - REMOVAL.......24-108
FUEL ENGINE OIL - DESCRIPTION,
FLEXIBLE.............................0-3
FUEL FILL DOOR - INSTALLATION.......23-51
FUEL FILL DOOR - REMOVAL...........23-51
FUEL FILL DOOR BLOCKER LATCH -
INSTALLATION.......................23-52
FUEL FILL DOOR BLOCKER LATCH -
REMOVAL..........................23-52
FUEL FILL DOOR BLOCKER LATCH
STRIKER - INSTALLATION..............23-52
FUEL FILL DOOR BLOCKER LATCH
STRIKER - REMOVAL.................23-52
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - INSTALLATION.................23-53
FUEL FILL DOOR BLOCKER LOCKOUT
LINK - REMOVAL.....................23-52
FUEL FILLER CAP - DESCRIPTION.......25-12
FUEL FILLER CAP - OPERATION.........25-12
FUEL FILTER - INSTALLATION............14-4
FUEL FILTER - REMOVAL...............14-4
FUEL INJECTOR - DESCRIPTION.........14-26
FUEL INJECTOR - OPERATION..........14-26
FUEL LEVEL SENDING UNIT / SENSOR -
DESCRIPTION........................14-4
FUEL LEVEL SENDING UNIT / SENSOR -
INSTALLATION........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
OPERATION..........................14-5
FUEL LEVEL SENDING UNIT / SENSOR -
REMOVAL...........................14-5
FUEL LINE - INSTALLATION...........24-110
FUEL LINE - REMOVAL...............24-109
FUEL LINES/HOSES AND CLAMPS -
DESCRIPTION........................14-6
FUEL PRESSURE REGULATOR -
INSTALLATION........................14-7
FUEL PRESSURE REGULATOR -
OPERATION..........................14-7
FUEL PRESSURE REGULATOR -
REMOVAL...........................14-7
FUEL PUMP - DESCRIPTION.............14-7
FUEL PUMP - OPERATION..............14-7
FUEL PUMP MODULE - DESCRIPTION.....14-8
FUEL PUMP MODULE - INSTALLATION....14-9
FUEL PUMP MODULE - OPERATION.......14-8
FUEL PUMP MODULE - REMOVAL
........14-8
FUEL PUMP RELAY - DESCRIPTION
......14-28
FUEL PUMP RELAY - OPERATION
........14-28
FUEL REQUIREMENTS - DESCRIPTION
......0-4
FUEL REQUIREMENTS - DIESEL ENGINE
- DESCRIPTION
........................0-6FUEL, SPECIAL TOOLS............14-23,14-3
FUEL SYSTEM PRESSURE RELEASE
PROCEDURE - STANDARD
PROCEDURE.........................14-2
FUEL SYSTEM PRESSURE,
SPECIFICATIONS......................14-3
FUEL TANK - DESCRIPTION............14-10
FUEL TANK - INSTALLATION............14-11
FUEL TANK - OPERATION..............14-10
FUEL TANK - REMOVAL...............14-11
FUEL TANK - STANDARD PROCEDURE,
DRAINING...........................14-2
FUEL TANK FILLER TUBE -
INSTALLATION.......................14-12
FUEL TANK FILLER TUBE - REMOVAL....14-12
FULL OPEN SWITCH - DESCRIPTION....8N-12,
8N-31
FULL OPEN SWITCH - INSTALLATION....8N-13
FULL OPEN SWITCH - OPERATION . 8N-12,8N-31
FULL OPEN SWITCH - REMOVAL........8N-13
FUNCTIONS - DESCRIPTION, CIRCUIT . . 8W-01-6
FUSE - DESCRIPTION, IOD...........8W-97-4
FUSE - INSTALLATION, IOD..........8W-97-5
FUSE - OPERATION, IOD.............8W-97-5
FUSE - REMOVAL, IOD..............8W-97-5
FUSES POWERING SEVERAL LOADS -
STANDARD PROCEDURE, TESTING
FOR A SHORT TO GROUND ON......8W-01-10
FWD - INSTALLATION..............2-41,2-44
FWD - INSTALLATION, REAR WHEEL
SPEED SENSOR.......................5-81
FWD - REMOVAL..................2-40,2-44
FWD - REMOVAL, REAR WHEEL SPEED
SENSOR............................5-81
GALLERY PLUGS - STANDARD
PROCEDURE, ENGINE CORE AND OIL . 9-10,9-86
GAP - STANDARD PROCEDURE,
COMPRESSOR CLUTCH AIR............24-17
GAP AND FLUSH MEASUREMENTS -
SPECIFICATIONS....................23-121
GAP, SPECIFICATIONS - WHEEL SPEED
SENSOR AIR.........................5-79
GAS - INSTALLATION, MODULAR
CLUTCH ASSY - 2.4L..................6-11
GAS - REMOVAL, MODULAR CLUTCH
ASSY - 2.4L..........................6-11
GASKET - DIAGNOSIS AND TESTING,
CYLINDER HEAD..................9-24,9-99
GASKET SURFACE PREPARATION -
STANDARD PROCEDURE, ENGINE....9-11,9-85
GASKETS AND SEALERS - STANDARD
PROCEDURE, FORM-IN-PLACE.......9-11,9-84
GEAR - DESCRIPTION.................19-26
GEAR - INSTALLATION, LHD............19-32
GEAR - INSTALLATION, RHD............19-33
GEAR & LINK ROD - DESCRIPTION, LIFT . 8N-16
GEAR & LINK ROD - INSTALLATION,
LIFT...............................8N-16
GEAR & LINK ROD - OPERATION, LIFT . . . 8N-16
GEAR & LINK ROD - REMOVAL, LIFT.....8N-16
GEAR - OPERATION...................19-27
GEAR - REMOVAL, LHD...............19-27
GEAR - REMOVAL, RHD...............19-31
GEAR END PLAY - ADJUSTMENT,
DIFFERENTIAL SIDE..................21-70
GEAR SHIFT CABLE - INSTALLATION....21-205
GEAR SHIFT CABLE - REMOVAL........21-204
GEAR SHIFT LEVER - INSTALLATION.....19-21
GEAR SHIFT LEVER - REMOVAL.........19-21
GEAR, SPECIAL TOOLS - POWER
STEERING..........................19-34
GEARSHIFT BOOT - INSTALLATION......21-73
GEARSHIFT BOOT - REMOVAL..........21-72
GEARSHIFT CABLE - CROSSOVER -
INSTALLATION.......................21-76
GEARSHIFT CABLE - CROSSOVER -
REMOVAL..........................21-73
GEARSHIFT CABLE - SELECTOR -
INSTALLATION.......................21-84
GEARSHIFT CABLE - SELECTOR -
REMOVAL..........................21-81
GEARSHIFT CABLE ADJUSTMENT,
ADJUSTMENTS
.....................21-206
GEARSHIFT KNOB - INSTALLATION
......21-87
GEARSHIFT KNOB - REMOVAL
..........21-87
GEARSHIFT MECHANISM -
INSTALLATION
.......................21-89
GEARSHIFT MECHANISM - REMOVAL
....21-87GEARTRAIN - DESCRIPTION,
PLANETARY........................21-232
GEARTRAIN - OPERATION, PLANETARY . . 21-232
GENERAL - WARNINGS.............8W-01-7
GENERAL DIAGNOSIS - DIAGNOSIS AND
TESTING, 41TE TRANSAXLE...........21-119
GENERATOR - DESCRIPTION...........8F-23
GENERATOR - OPERATION.............8F-23
GENERATOR DECOUPLER PULLEY -
DESCRIPTION.......................8F-25
GENERATOR DECOUPLER PULLEY -
DIAGNOSIS AND TESTING..............8F-25
GENERATOR DECOUPLER PULLEY -
INSTALLATION.......................8F-26
GENERATOR DECOUPLER PULLEY -
OPERATION.........................8F-25
GENERATOR DECOUPLER PULLEY -
REMOVAL..........................8F-26
GENERATOR, SPECIFICATIONS..........8F-22
GLASS - DESCRIPTION, HEATED.........8G-1
GLASS - INSTALLATION, DOOR.........23-17
GLASS - INSTALLATION, REAR DOOR . . . 23-108
GLASS - INSTALLATION, SIDE VIEW
MIRROR...........................23-58
GLASS - INSTALLATION, SLIDING DOOR . 23-107
GLASS - OPERATION, HEATED...........8G-1
GLASS - REMOVAL, DOOR.............23-17
GLASS - REMOVAL, REAR DOOR.......23-108
GLASS - REMOVAL, SIDE VIEW MIRROR . . 23-58
GLASS - REMOVAL, SLIDING DOOR.....23-107
GLASS INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER...............8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER.....8A-9
GLASS INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER.................8A-9
GLASS PANEL - INSTALLATION........23-117
GLASS PANEL - REMOVAL............23-117
GLASS PANEL ADJUSTMENT,
ADJUSTMENTS - SUNROOF...........23-117
GLASS RUN WEATHERSTRIP -
INSTALLATION, FRONT DOOR..........23-110
GLASS RUN WEATHERSTRIP -
REMOVAL, FRONT DOOR.............23-110
GLOVE BOX - INSTALLATION...........23-63
GLOVE BOX - REMOVAL...............23-63
GLOVE BOX LAMP SWITCH -
INSTALLATION.......................8L-26
GLOVE BOX LAMP SWITCH - REMOVAL . . 8L-26
GLOVE BOX LATCH - INSTALLATION.....23-63
GLOVE BOX LATCH - REMOVAL.........23-63
GLOVE BOX LATCH STRIKER -
INSTALLATION.......................23-64
GLOVE BOX LATCH STRIKER - REMOVAL . 23-64
GRID LINE AND TERMINAL REPAIR -
STANDARD PROCEDURE...............8G-3
GRID LINE REPAIR REAR - STANDARD
PROCEDURE.........................8G-2
GRILLE - INSTALLATION, COWL.........23-50
GRILLE - REMOVAL, COWL............23-49
GRILLE OPENING REINFORCEMENT -
INSTALLATION
.......................23-53
GRILLE OPENING REINFORCEMENT -
REMOVAL
..........................23-53
GROCERY BAG RETAINER -
INSTALLATION, PLASTIC
..............23-103
GROCERY BAG RETAINER - REMOVAL,
PLASTIC
..........................23-103
GROMMET REPLACEMENT - STANDARD
PROCEDURE, PUSH-PIN
...............8N-28
GROUND - OPERATION, PCM
...........8E-15
GROUND - STANDARD PROCEDURE,
TESTING FOR A SHORT TO
..........8W-01-9
GROUND AND SPLICE INFORMATION -
DESCRIPTION, CONNECTOR
..........8W-01-7
GROUND ON FUSES POWERING
SEVERAL LOADS - STANDARD
PROCEDURE, TESTING FOR A SHORT
TO
.............................8W-01-10
GUIDE - INSTALLATION, UNDER SEAT
STORAGE BIN
......................23-104
GUIDE - REMOVAL, UNDER SEAT
STORAGE BIN
......................23-104
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - ASSEMBLY, CALIPER
..........5-25
GUIDE PIN BUSHINGS (DISC/DISC
BRAKES) - DISASSEMBLY, CALIPER
.......5-24
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

MANUAL ADJUSTER - INSTALLATION,
FRONT SEAT TRACK..................23-94
MANUAL ADJUSTER - REMOVAL, FRONT
SEAT TRACK........................23-94
MANUAL THREE ZONE - DESCRIPTION....24-1
MANUAL THREE ZONE - OPERATION......24-3
MANUAL TRACK - INSTALLATION,
FRONT SEAT RISER...................23-93
MANUAL TRACK - REMOVAL, FRONT
SEAT RISER.........................23-93
MANUAL TRANSAXLE - ASSEMBLY, T850 . 21-42
MANUAL TRANSAXLE - DESCRIPTION,
T850..............................21-21
MANUAL TRANSAXLE - DISASSEMBLY,
T850..............................21-35
MANUAL TRANSAXLE - INSTALLATION,
T850..............................21-51
MANUAL TRANSAXLE - OPERATION,
T850..............................21-24
MANUAL TRANSAXLE - REMOVAL, T850 . . 21-31
MANUAL TRANSAXLE - SPECIFICATIONS,
T850..............................21-56
MANUFACTURER PLATE - DESCRIPTION . Intro.-11
MAP SENSOR - DESCRIPTION..........14-30
MAP SENSOR - OPERATION............14-30
MASTER CYLINDER - LHD -
INSTALLATION........................6-10
MASTER CYLINDER - LHD - REMOVAL.....6-9
MASTER CYLINDER - RHD -
INSTALLATION.........................6-9
MASTER CYLINDER - RHD - REMOVAL.......6-8
MASTER CYLINDER BLEEDING -
STANDARD PROCEDURE................5-35
MASTER CYLINDER (FLUID RESERVOIR)
- ASSEMBLY.........................5-38
MASTER CYLINDER (FLUID RESERVOIR)
- DISASSEMBLY......................5-37
MATCH MOUNTING - STANDARD
PROCEDURE, TIRE AND WHEEL..........22-7
MATS - INSTALLATION, CARPETS AND
FLOOR.............................23-75
MATS - REMOVAL, CARPETS AND
FLOOR.............................23-74
MEASUREMENT - STANDARD
PROCEDURE, CURB HEIGHT.............2-54
MEASUREMENTS - SPECIFICATIONS,
GAP AND FLUSH....................23-121
MEASURING BEARING CLEARANCE
USING PLASTIGAGE - STANDARD
PROCEDURE.....................9-12,9-84
MEASURING CAMSHAFT END PLAY -
STANDARD PROCEDURE................9-29
MEASURING CONNECTING ROD
BEARING CLEARANCE - STANDARD
PROCEDURE........................9-120
MEASURING CRANKSHAFT END PLAY -
STANDARD PROCEDURE...............9-125
MEASURING TIMING CHAIN WEAR -
STANDARD PROCEDURE...............9-153
MECHANICAL - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-6,9-80
MECHANISM - INSTALLATION,
GEARSHIFT.........................21-89
MECHANISM - REMOVAL, GEARSHIFT....21-87
MEMORIES, OPERATION - FUEL
CORRECTION OR ADAPTIVE............14-20
MEMORY SEAT/MIRROR MODULE -
DESCRIPTION.......................8E-10
MEMORY SEAT/MIRROR MODULE -
DIAGNOSIS AND TESTING
.............8E-10
MEMORY SEAT/MIRROR MODULE -
INSTALLATION
.......................8E-10
MEMORY SEAT/MIRROR MODULE -
OPERATION
.........................8E-10
MEMORY SEAT/MIRROR MODULE -
REMOVAL
..........................8E-10
MEMORY SET SWITCH - DESCRIPTION
. . . 8N-55
MEMORY SET SWITCH - INSTALLATION
. . 8N-56
MEMORY SET SWITCH - OPERATION
....8N-56
MEMORY SET SWITCH - REMOVAL
......8N-56
MEMORY SWITCH - DIAGNOSIS AND
TESTING
...........................8N-56
MEMORY SYSTEM - DESCRIPTION
......8N-51
MEMORY SYSTEM - DIAGNOSIS AND
TESTING
...........................8N-53
MEMORY SYSTEM - OPERATION
........8N-52
METRIC SYSTEM - DESCRIPTION
......Intro.-6MINI-TRIP COMPUTER - DIAGNOSIS
AND TESTING, COMPASS.............8M-10
MIRROR - DESCRIPTION, AUTOMATIC
DAY / NIGHT........................8N-47
MIRROR - DIAGNOSIS AND TESTING,
AUTOMATIC DAY / NIGHT..............8N-47
MIRROR - INSTALLATION, REAR VIEW . . . 23-80
MIRROR - INSTALLATION, SIDE VIEW....23-57
MIRROR - OPERATION, AUTOMATIC DAY
/ NIGHT............................8N-47
MIRROR - REMOVAL, REAR VIEW.......23-79
MIRROR - REMOVAL, SIDE VIEW........23-57
MIRROR - REMOVAL, SIDEVIEW........8N-49
MIRROR - STANDARD PROCEDURE,
HEATED.............................8G-6
MIRROR GLASS - INSTALLATION, SIDE
VIEW..............................23-58
MIRROR GLASS - REMOVAL, SIDE VIEW . . 23-58
MIRROR SWITCH - DESCRIPTION........8G-5
MIRROR SWITCH - EXPORT -
DESCRIPTION, POWER FOLDAWAY......8N-48
MIRROR SWITCH - EXPORT -
INSTALLATION, POWER FOLDAWAY......8N-49
MIRROR SWITCH - EXPORT -
OPERATION, POWER FOLDAWAY........8N-48
MIRROR SWITCH - EXPORT - REMOVAL,
POWER FOLDAWAY..................8N-48
MIRROR SWITCH - OPERATION..........8G-5
MIRROR TEST - DIAGNOSIS AND
TESTING, HEATED.....................8G-5
MIRRORS - DESCRIPTION, HEATED........8G-5
MIRRORS - DESCRIPTION, POWER......8N-45
MIRRORS - DIAGNOSIS AND TESTING,
POWER............................8N-46
MIRRORS - OPERATION, HEATED........8G-5
MIRRORS - OPERATION, POWER........8N-45
MISALIGNMENT - DIAGNOSIS AND
TESTING, DRIVE PLATE.................6-6
MODE DOOR ACTUATOR - DESCRIPTION . . 24-24
MODE DOOR ACTUATOR -
INSTALLATION..................24-25,24-36
MODE DOOR ACTUATOR - OPERATION . . . 24-24
MODE DOOR ACTUATOR - REMOVAL....24-25,
24-36
MODE, OPERATION - DRB IIITS TAT E
DISPLAY TEST........................25-9
MODES OF OPERATION - OPERATION....14-18
MODULAR CLUTCH ASSY - 2.4L GAS -
INSTALLATION........................6-11
MODULAR CLUTCH ASSY - 2.4L GAS -
REMOVAL...........................6-11
MODULE - DESCRIPTION, BODY
CONTROL...........................8E-3
MODULE - DESCRIPTION, FRONT
CONTROL...........................8E-7
MODULE - DESCRIPTION, FUEL PUMP....14-8
MODULE - DESCRIPTION, HEATED SEAT . . . 8E-8
MODULE - DESCRIPTION, INTEGRATED
POWER..........................8W-97-3
MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER . . 24-25,24-37
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT
........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR
...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY
.............8N-43
MODULE - EXPORT - DESCRIPTION,
ANTENNA
...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA
...................8A-7MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA...........................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-4
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER . 24-26,24-38
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-18
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP........14-8
MODULE - OPERATION, HEATED SEAT.....8E-9
MODULE - OPERATION, INTEGRATED
POWER..........................8W-97-3
MODULE - OPERATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - OPERATION, POWER....24-26,24-37
MODULE - OPERATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - OPERATION, REAR
DRIVELINE...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - OPERATION, SIDE IMPACT
AIRBAG CONTROL...................8O-17
MODULE - OPERATION, SLIDING DOOR
CONTROL..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL..........................8E-20
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-4
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER.....24-26,24-37
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY
.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - REMOVAL, SIDE IMPACT
AIRBAG CONTROL
...................8O-17
MODULE - REMOVAL, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - REMOVAL, WIPER
...........8R-18
MODULE - SPECIFICATIONS, REAR
DRIVELINE
...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT
.........................23-86
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE
...............8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE
.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE
.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT
..................23-112
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT
..................23-110
MOLDING - INSTALLATION, ROOF JOINT
. . 23-57
20 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

UNDER SEAT STORAGE BIN LOCK/LATCH
- REMOVAL........................23-104
UNDERBODY LINES - DESCRIPTION.....24-103
UNDERBODY LINES - OPERATION......24-103
UNIT - DESCRIPTION, LOWER DRIVE....8N-32
UNIT - DESCRIPTION, POWER
TRANSFER...........................21-1
UNIT - EXPORT - INSTALLATION,
HEADLAMP.........................8L-20
UNIT - EXPORT - REMOVAL, HEADLAMP . . 8L-20
UNIT - INSTALLATION, CENTER HIGH
MOUNTED STOP LAMP.................8L-7
UNIT - INSTALLATION, HEATER........24-111
UNIT - INSTALLATION, LOWER DRIVE....8N-33
UNIT - INSTALLATION, TAIL LAMP.......8L-23
UNIT - OPERATION, LOWER DRIVE......8N-32
UNIT - OPERATION, POWER TRANSFER....21-3
UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP LAMP.................8L-6
UNIT - REMOVAL, HEATER............24-111
UNIT - REMOVAL, LOWER DRIVE.......8N-33
UNIT - REMOVAL, TAIL LAMP...........8L-23
UNIT / SENSOR - DESCRIPTION, FUEL
LEVEL SENDING......................14-4
UNIT / SENSOR - INSTALLATION, FUEL
LEVEL SENDING......................14-5
UNIT / SENSOR - OPERATION, FUEL
LEVEL SENDING......................14-5
UNIT / SENSOR - REMOVAL, FUEL
LEVEL SENDING........................14-5
UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, FRONT FOG
LAMP...............................8L-9
UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, HEADLAMP....8L-17
UNIT ALIGNMENT - STANDARD
PROCEDURE, FRONT FOG LAMP.........8L-9
UNIT ALIGNMENT - STANDARD
PROCEDURE, HEADLAMP..............8L-17
UNIT, SPECIAL TOOLS - SDP POWER
TRANSFER...........................21-8
UNIT TRACK & RACK - DESCRIPTION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - INSTALLATION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - OPERATION,
LOWER DRIVE......................8N-34
UNIT TRACK & RACK - REMOVAL,
LOWER DRIVE......................8N-34
UNIVERSAL TRANSMITTER -
DESCRIPTION.......................8M-10
UNIVERSAL TRANSMITTER - DIAGNOSIS
AND TESTING.......................8M-10
UNIVERSAL TRANSMITTER - OPERATION . 8M-10
UPPER - INSPECTION, INTAKE
MANIFOLD...........................9-59
UPPER - INSTALLATION, INTAKE
MANIFOLD...........................9-59
UPPER - INSTALLATION, SHROUD.......19-23
UPPER - REMOVAL, INTAKE MANIFOLD....9-58
UPPER - REMOVAL, SHROUD...........19-23
UPPER HINGE - INSTALLATION.........23-35
UPPER HINGE - REMOVAL.............23-35
UPPER INTAKE MANIFOLD -
INSTALLATION.......................9-147
UPPER INTAKE MANIFOLD - REMOVAL . . . 9-145
UPPER TRIM - INSTALLATION, B-PILLAR
. . 23-74
UPPER TRIM - REMOVAL, B-PILLAR
.....23-74
UPSTOP SWITCH - INSTALLATION,
CLUTCH PEDAL
.......................6-16
UPSTOP SWITCH - REMOVAL, CLUTCH
PEDAL
..............................6-15
UPSTREAM 1/1 - 2.4L - INSTALLATION
. . . 14-33
UPSTREAM 1/1 - 2.4L - REMOVAL
.......14-33
UPSTREAM 1/1 - 3.3/3.8L -
INSTALLATION
.......................14-34
UPSTREAM 1/1 - 3.3/3.8L - REMOVAL
....14-33
USAGE - DESCRIPTION, FASTENER
.....Intro.-5
USE WIRING DIAGRAMS -
DESCRIPTION, HOW TO
.............8W-01-1
USING PLASTIGAGE - STANDARD
PROCEDURE, MEASURING BEARING
CLEARANCE
.....................9-12,9-84
VAC LEAK DETECTION ASSY -
INSTALLATION, NATURAL
..............25-13
VAC LEAK DETECTION ASSY -
REMOVAL, NATURAL
..................25-13VACUUM PORT REPAIR - STANDARD
PROCEDURE, INTAKE MANIFOLD........9-145
VACUUM RESERVOIR - DESCRIPTION.....8P-6
VACUUM RESERVOIR - INSTALLATION....8P-6
VACUUM RESERVOIR - OPERATION.......8P-6
VACUUM RESERVOIR - REMOVAL........8P-6
VALVE - DESCRIPTION................25-22
VALVE - DESCRIPTION, EXPANSION . 24-72,24-96
VALVE - DESCRIPTION, PCV............25-16
VALVE - DIAGNOSIS AND TESTING,
EXPANSION....................24-72,24-97
VALVE - INSTALLATION, EXPANSION.....24-74,
24-98
VALVE - INSTALLATION, OIL PRESSURE
RELIEF.............................9-141
VALVE - OPERATION..................25-22
VALVE - OPERATION, EXPANSION . . 24-72,24-97
VALVE - OPERATION, PCV..............25-16
VALVE - REMOVAL, EXPANSION....24-73,24-97
VALVE - REMOVAL, OIL PRESSURE
RELIEF.............................9-141
VALVE BODY - ASSEMBLY............21-257
VALVE BODY - DESCRIPTION..........21-250
VALVE BODY - DISASSEMBLY..........21-252
VALVE BODY - INSTALLATION..........21-262
VALVE BODY - OPERATION............21-250
VALVE BODY - REMOVAL.............21-251
VALVE (HEIGHT SENSING) -
DESCRIPTION, PROPORTIONING.........5-48
VALVE (HEIGHT SENSING) - DIAGNOSIS
AND TESTING, PROPORTIONING.........5-49
VALVE (HEIGHT SENSING) -
INSTALLATION, PROPORTIONING.........5-51
VALVE (HEIGHT SENSING) - OPERATION,
PROPORTIONING.....................5-48
VALVE (HEIGHT SENSING) - REMOVAL,
PROPORTIONING.....................5-50
VALVE SEATS - STANDARD PROCEDURE,
REFACING VALVES...................9-104
VALVE SPRINGS - DESCRIPTION........9-106
VALVE SPRINGS - OPERATION..........9-106
VALVE STEM SEALS - DESCRIPTION.....9-111
VALVE STEM SEALS - INSTALLATION.....9-112
VALVE STEM SEALS - REMOVAL........9-112
VALVE TIMING VERIFICATION -
STANDARD PROCEDURE...............9-153
VALVES - OPERATION, HYDRAULIC
CIRCUITS............................5-83
VALVES & SEATS - CLEANING,
INTAKE/EXHAUST................9-105,9-32
VALVES & SEATS - DESCRIPTION,
INTAKE/EXHAUST................9-104,9-32
VALVES & SEATS - INSPECTION,
INTAKE/EXHAUST....................9-105
VALVES & SEATS - INSTALLATION,
INTAKE/EXHAUST....................9-106
VALVES & SEATS - OPERATION,
INTAKE/EXHAUST....................9-104
VALVES & SEATS - REMOVAL,
INTAKE/EXHAUST....................9-105
VALVES AND VALVE SEATS - STANDARD
PROCEDURE, REFACING...............9-104
VANITY LAMP - INSTALLATION.........8L-28
VANITY LAMP - REMOVAL.............8L-28
VAPOR CANISTER - DESCRIPTION
.......25-18
VAPOR CANISTER - OPERATION
.........25-18
VARIABLE BRAKE PROPORTIONING -
DESCRIPTION, ELECTRONIC
.............5-75
VARIABLE BRAKE PROPORTIONING -
OPERATION, ELECTRONIC
...............5-77
VARIATION ADJUSTMENT - STANDARD
PROCEDURE, COMPASS
...............8M-5
VECI LABEL - DESCRIPTION
..........Intro.-11
VEHICLE DOES NOT FILL - DIAGNOSIS
AND TESTING
.......................25-16
VEHICLE EMISSION CONTROL
INFORMATION LABEL - DESCRIPTION
.....25-1
VEHICLE IDENTIFICATION -
DESCRIPTION
........................23-1
VEHICLE IDENTIFICATION NUMBER -
DESCRIPTION
......................Intro.-9
VEHICLE INFO CENTER - DESCRIPTION,
ELECTRONIC
........................8M-6
VEHICLE INFO CENTER - INSTALLATION,
ELECTRONIC
........................8M-9
VEHICLE INFO CENTER - OPERATION,
ELECTRONIC
........................8M-7VEHICLE INFO CENTER - REMOVAL,
ELECTRONIC........................8M-9
VEHICLE INFORMATION CENTER -
DIAGNOSIS AND TESTING,
ELECTRONIC........................8M-7
VEHICLE INFORMATION CENTER
PROGRAMMING - STANDARD
PROCEDURE, ELECTRONIC.............8M-7
VEHICLE SAFETY CERTIFICATION LABEL
- DESCRIPTION....................Intro.-11
VEHICLE SPEED SENSOR -
INSTALLATION......................21-115
VEHICLE SPEED SENSOR - REMOVAL . . . 21-115
VEHICLE THEFT SECURITY -
DESCRIPTION........................8Q-1
VEHICLE THEFT SECURITY - OPERATION . . 8Q-1
VEHICLE THEFT SECURITY SYSTEM -
DIAGNOSIS AND TESTING..............8Q-3
VENT WINDOW MOTOR - DIAGNOSIS
AND TESTING.......................8N-63
VENT WINDOW MOTOR - INSTALLATION . . 8N-64
VENT WINDOW MOTOR - REMOVAL.....8N-63
VERIFICATION - STANDARD
PROCEDURE, VALVE TIMING...........9-153
VIBRATION - DIAGNOSIS AND TESTING,
TIRE AND WHEEL.....................22-1
VIBRATION DAMPER - INSTALLATION....9-130,
9-47
VIBRATION DAMPER - REMOVAL....9-130,9-47
VIDEO SCREEN - DESCRIPTION.........8A-16
VIDEO SCREEN - INSTALLATION........8A-16
VIDEO SCREEN - OPERATION............8A-16
VIDEO SCREEN - REMOVAL............8A-16
VIEW MIRROR - INSTALLATION, REAR . . . 23-80
VIEW MIRROR - INSTALLATION, SIDE....23-57
VIEW MIRROR - REMOVAL, REAR.......23-79
VIEW MIRROR - REMOVAL, SIDE........23-57
VIEW MIRROR GLASS - INSTALLATION,
SIDE..............................23-58
VIEW MIRROR GLASS - REMOVAL, SIDE . . 23-58
VISCOUS COUPLER - DESCRIPTION.......3-41
VISCOUS COUPLER - OPERATION........3-42
VISOR - INSTALLATION, SUN...........23-81
VISOR - REMOVAL, SUN...............23-81
VISOR SUPPORT - INSTALLATION, SUN . . . 23-81
VISOR SUPPORT - REMOVAL, SUN......23-81
VOLT SUPPLY - PCM OUTPUT -
OPERATION, 5.......................8E-15
VOLTAGE DROP - STANDARD
PROCEDURE, TESTING FOR A.......8W-01-10
VOLTAGE POTENTIAL - STANDARD
PROCEDURE, TESTING OF...........8W-01-9
VOLTAGE REGULATOR - DESCRIPTION....8F-27
VOLTAGE REGULATOR - OPERATION.....8F-27
VOLTAGE TEST - STANDARD
PROCEDURE, OPEN-CIRCUIT...........8F-13
VTSS/SKIS INDICATOR LAMP -
DESCRIPTION........................8Q-5
VTSS/SKIS INDICATOR LAMP -
OPERATION..........................8Q-5
WARNING - INSTALLATION............23-106
WARNING - INSTALLATION.............19-13
WARNING - REMOVAL...............23-105
WARNING - REMOVAL................19-12
WARNING - SAFETY PRECAUTIONS AND
WARNINGS..........................23-1
WARNING - WARNING................24-61
WARNING - WARNINGS AND CAUTIONS . . 19-10,
19-27
WARNING - WINDSHIELD SAFETY
PRECAUTIONS......................23-105
WARNING, A/C PLUMBING.............24-61
WARNING, CHIME/BUZZER..............8B-1
WARNING, DESCRIPTION................5-4
WARNING, DESCRIPTION..............19-37
WARNING, LAMPS/LIGHTING -
EXTERIOR...........................8L-4
WARNING, RESTRAINTS................8O-2
WARNING, WARNING.................24-61
WARNINGS AND CAUTIONS, WARNING
. . 19-10,
19-27
WARNINGS, GENERAL
..............8W-01-7
WARNINGS, WARNING - SAFETY
PRECAUTIONS
........................23-1
WASHER FLUID LEVEL SWITCH -
INSTALLATION
......................8R-16
WASHER FLUID LEVEL SWITCH -
REMOVAL
..........................8R-15
RSINDEX35
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com

WASHER HOSE - EXPORT -
INSTALLATION, HEADLAMP............8R-12
WASHER HOSE - EXPORT - REMOVAL,
HEADLAMP.........................8R-12
WASHER HOSES - INSTALLATION.......8R-16
WASHER HOSES - REMOVAL...........8R-16
WASHER PUMP MOTOR - EXPORT -
INSTALLATION, HEADLAMP............8R-13
WASHER PUMP MOTOR - EXPORT -
REMOVAL, HEADLAMP................8R-12
WASHER PUMP MOTOR -
INSTALLATION, FRONT.................8R-8
WASHER PUMP MOTOR -
INSTALLATION, REAR.................8R-14
WASHER PUMP MOTOR - REMOVAL,
FRONT..............................8R-8
WASHER PUMP MOTOR - REMOVAL,
REAR..............................8R-13
WASHER RESERVOIR - INSTALLATION . . . 8R-17
WASHER RESERVOIR - REMOVAL.......8R-16
WASHER SYSTEM - DIAGNOSIS AND
TESTING............................8R-4
WASHERS - EXPORT - DESCRIPTION,
HEADLAMP.........................8R-10
WASHERS - EXPORT - DIAGNOSIS AND
TESTING, HEADLAMP.................8R-10
WASHERS - EXPORT - INSTALLATION,
HEADLAMP.........................8R-12
WASHERS - EXPORT - OPERATION,
HEADLAMP.........................8R-10
WASHERS - EXPORT - REMOVAL,
HEADLAMP.........................8R-12
WATER CHANNEL - INSTALLATION......23-118
WATER CHANNEL - REMOVAL.........23-118
WATER LEAKS - DIAGNOSIS AND
TESTING............................23-2
WATER PUMP - 2.4L - CLEANING........7-32
WATER PUMP - 2.4L - DESCRIPTION......7-31
WATER PUMP - 2.4L - INSPECTION.......7-32
WATER PUMP - 2.4L - INSTALLATION.....7-32
WATER PUMP - 2.4L - REMOVAL.........7-31
WATER PUMP - 3.3/3.8L - CLEANING.....7-34
WATER PUMP - 3.3/3.8L - DESCRIPTION . . . 7-33
WATER PUMP - 3.3/3.8L - INSPECTION....7-34
WATER PUMP - 3.3/3.8L -
INSTALLATION........................7-34
WATER PUMP - 3.3/3.8L - REMOVAL......7-33
WATER PUMP INLET TUBE - 2.4L -
DESCRIPTION........................7-35
WATER PUMP INLET TUBE - 2.4L -
INSTALLATION........................7-35
WATER PUMP INLET TUBE - 2.4L -
REMOVAL...........................7-35
WATER PUMP INLET TUBE - 3.3/3.8L -
INSTALLATION........................7-36
WATER PUMP INLET TUBE - 3.3/3.8L -
REMOVAL...........................7-36
WATERSHIELD - INSTALLATION.........23-21
WATERSHIELD - REMOVAL.............23-21
WEAR - STANDARD PROCEDURE,
MEASURING TIMING CHAIN............9-153
WEAR INDICATORS - DIAGNOSIS AND
TESTING, TREAD.....................22-16
WEAR PATTERNS - DIAGNOSIS AND
TESTING, TIRE......................22-16
WEATHERSTRIP - INSTALLATION, FRONT
DOOR............................23-111
WEATHERSTRIP - INSTALLATION, FRONT
DOOR GLASS RUN..................23-110
WEATHERSTRIP - INSTALLATION,
SLIDING DOOR.....................23-112
WEATHERSTRIP - REMOVAL, FRONT
DOOR............................23-111
WEATHERSTRIP - REMOVAL, FRONT
DOOR GLASS RUN..................23-110
WEATHERSTRIP - REMOVAL, SLIDING
DOOR............................23-112WELD LOCATIONS - SPECIFICATIONS . . . 23-161
WHEEL - DESCRIPTION...............22-18
WHEEL - INSPECTION, TONE............5-82
WHEEL - INSTALLATION, STEERING......19-24
WHEEL - REMOVAL, STEERING.........19-23
WHEEL ALIGNMENT - DESCRIPTION......2-46
WHEEL ALIGNMENT - STANDARD
PROCEDURE.........................2-51
WHEEL ALIGNMENT, SPECIFICATIONS.....2-55
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- INSTALLATION, TIRE.................22-8
WHEEL ASSEMBLY (ALUMINUM WHEEL)
- REMOVAL, TIRE.....................22-7
WHEEL ASSEMBLY (STEEL WHEEL) -
INSTALLATION, TIRE...................22-8
WHEEL ASSEMBLY (STEEL WHEEL) -
REMOVAL, TIRE......................22-8
WHEEL BALANCE - STANDARD
PROCEDURE, TIRE....................22-5
WHEEL CARE - CLEANING, ALUMINUM . . . 22-18
WHEEL COVER - DESCRIPTION.........22-19
WHEEL COVER - INSTALLATION.........22-19
WHEEL COVER - REMOVAL............22-19
WHEEL CYLINDERS - INSPECTION........5-57
WHEEL CYLINDERS - INSTALLATION......5-57
WHEEL CYLINDERS - REMOVAL..........5-57
WHEEL INSPECTION - DIAGNOSIS AND
TESTING...........................22-18
WHEEL MATCH MOUNTING - STANDARD
PROCEDURE, TIRE....................22-7
WHEEL MOUNTING STUDS - FRONT -
INSTALLATION.......................22-21
WHEEL MOUNTING STUDS - FRONT -
REMOVAL..........................22-20
WHEEL MOUNTING STUDS - REAR -
INSTALLATION.......................22-22
WHEEL MOUNTING STUDS - REAR -
REMOVAL..........................22-21
WHEEL ROTATION - STANDARD
PROCEDURE, TIRE....................22-7
WHEEL RUNOUT, SPECIFICATIONS -
TONE...............................5-79
WHEEL, SPECIFICATIONS..............22-19
WHEEL SPEED SENSOR - AWD -
INSTALLATION, REAR..................5-80
WHEEL SPEED SENSOR - AWD -
REMOVAL, REAR......................5-80
WHEEL SPEED SENSOR - FWD -
INSTALLATION, REAR..................5-81
WHEEL SPEED SENSOR - FWD -
REMOVAL, REAR......................5-81
WHEEL SPEED SENSOR -
INSTALLATION, FRONT.................5-80
WHEEL SPEED SENSOR - REMOVAL,
FRONT..............................5-79
WHEEL SPEED SENSOR AIR GAP,
SPECIFICATIONS......................5-79
WHEEL VIBRATION - DIAGNOSIS AND
TESTING, TIRE.......................22-1
WHEELHOUSE SPLASH SHIELD -
INSTALLATION, FRONT................23-54
WHEELHOUSE SPLASH SHIELD -
REMOVAL, FRONT....................23-54
WIND DEFLECTOR - INSTALLATION.....23-118
WIND DEFLECTOR - REMOVAL.........23-118
WIND NOISE - DIAGNOSIS AND TESTING . . 23-3
WINDOW - INSTALLATION, QUARTER . . . 23-108
WINDOW - REMOVAL, QUARTER.......23-108
WINDOW CRANK - INSTALLATION.......23-21
WINDOW CRANK - REMOVAL...........23-21
WINDOW DEFOGGER SWITCH -
DESCRIPTION, REAR..................8G-2
WINDOW DEFOGGER SWITCH -
OPERATION, REAR....................8G-2
WINDOW MOTOR - DIAGNOSIS AND
TESTING, VENT......................8N-63
WINDOW MOTOR - INSTALLATION, VENT . 8N-64WINDOW MOTOR - REMOVAL..........8N-64
WINDOW MOTOR - REMOVAL, VENT.....8N-63
WINDOW REGULATOR - MANUAL -
INSTALLATION.......................23-23
WINDOW REGULATOR - MANUAL -
REMOVAL..........................23-23
WINDOW REGULATOR - POWER -
INSTALLATION.......................23-22
WINDOW REGULATOR - POWER -
REMOVAL..........................23-22
WINDOW SWITCH - DIAGNOSIS AND
TESTING...........................8N-64
WINDOW SWITCH - INSTALLATION......8N-65
WINDOW SWITCH - REMOVAL..........8N-65
WINDOWS - DESCRIPTION, POWER.....8N-62
WINDOWS - DIAGNOSIS AND TESTING,
POWER............................8N-62
WINDOWS - OPERATION, POWER.......8N-62
WINDSHIELD - DESCRIPTION..........23-105
WINDSHIELD SAFETY PRECAUTIONS,
WARNING.........................23-105
WIPER ARM - INSTALLATION, REAR.....8R-14
WIPER ARM - REMOVAL, REAR.........8R-14
WIPER ARM ALIGNMENT - STANDARD
PROCEDURE, FRONT..................8R-8
WIPER ARMS - INSTALLATION, FRONT....8R-9
WIPER ARMS - REMOVAL, FRONT........8R-9
WIPER BLADES - CLEANING...........8R-17
WIPER BLADES - INSTALLATION........8R-17
WIPER BLADES - REMOVAL............8R-17
WIPER LINKAGE - INSTALLATION.......8R-18
WIPER LINKAGE - REMOVAL...........8R-17
WIPER MODULE - INSTALLATION.......8R-18
WIPER MODULE - REMOVAL...........8R-18
WIPER MOTOR - INSTALLATION, FRONT . . . 8R-9
WIPER MOTOR - INSTALLATION, REAR . . . 8R-15
WIPER MOTOR - REMOVAL, FRONT......8R-9
WIPER MOTOR - REMOVAL, REAR......8R-14
WIPER SYSTEM - DIAGNOSIS AND
TESTING, FRONT.....................8R-2
WIPER SYSTEM - DIAGNOSIS AND
TESTING, REAR......................8R-4
WIPERS/WASHERS - DESCRIPTION.......8R-1
WIPERS/WASHERS - OPERATION........8R-2
WIPER/WASHER SWITCH -
DESCRIPTION, REAR.................8R-15
WIPER/WASHER SWITCH - DIAGNOSIS
AND TESTING, FRONT.................8R-2
WIPER/WASHER SWITCH - OPERATION,
REAR..............................8R-15
WIRE SPLICING - STANDARD
PROCEDURE.....................8W-01-15
WIRING - INSTALLATION,
SUPPLEMENTAL DIESEL HEATER.......24-112
WIRING - REMOVAL, SUPPLEMENTAL
DIESEL HEATER.....................24-112
WIRING DIAGRAMS - DESCRIPTION,
HOW TO USE .....................8W-01-1
WIRING HARNESS - DESCRIPTION......8N-35
WIRING HARNESS - DIAGNOSIS AND
TESTING.........................8W-01-7
WIRING HARNESS - INSTALLATION......8N-36
WIRING HARNESS - OPERATION........8N-35
WIRING HARNESS - REMOVAL.........8N-35
WIRING/TERMINAL, SPECIAL TOOLS . . 8W-01-10
WORN THREADS - STANDARD
PROCEDURE, REPAIR OF DAMAGED
OR
.............................9-10,9-86
ZONE - DESCRIPTION, DUAL
............24-1
ZONE - DESCRIPTION, MANUAL THREE
....24-1
ZONE - DESCRIPTION, SINGLE
...........24-1
ZONE - OPERATION, DUAL
..............24-3
ZONE - OPERATION, MANUAL THREE
.....24-3
ZONE ATC - OPERATION, THREE
.........24-3
ZONE ATC - OPERATION, TWO
.........24-106
36 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
ProCarManuals.com