engine CHRYSLER VOYAGER 2000 Diagnostic Manual

Symptom:
* CHECKING SPEED CONTROL OPERATION
POSSIBLE CAUSES
BRAKE SWITCH DEFECTIVE
GROUND CIRCUIT OPEN
S/C BRAKE SWITCH OUTPUT CIRCUIT SHORTED TO GROUND
SPEED CONTROL BRAKE SWITCH OUTPUT SUPPLY CKT OPEN
SPEED CONTROL ON/OFF/SET SWITCH DEFECTIVE
SPEED CONTROL POWER SUPPLY CIRCUIT OPEN
SPEED CONTROL POWER SUPPLY CIRCUIT SHORTED/GROUND
SPEED CONTROL SERVO CONNECTOR OBSERVABLE DEFECT
SPEED CONTROL SWITCH DEFECTIVE
CLOCK SPRING DEFECTIVE
SPEED CONTROL SERVO DEFECTIVE
SPEED CONTROL THROTTLE CABLE DEFECTIVE
SPEED CONTROL VACUUM SUPPLY LEAKS OR RESTRICTED
PCM DEFECTIVE (SPEED CONTROL OPERATION)
VACUUM RESERVOIR DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, monitor the Speed Control Switch inputs.
While observing display, press the Speed Control ON/OFF switch.
Does the DRB show S/C ON/OFF switch9ON9?All
Ye s®Go To 2
No®Refer to symptom SPEED CONTROL ON/OFF SWITCH in the
SPEED CONTROL category.
2 Ignition On, Engine Not Running
Press the S/C ON/OFF button to select S/C ªON.º
With the DRB, monitor the Speed Control Switch inputs.
While observing the DRB, press the ACCEL/RESUME/CANCEL and DECEL
switches several times.
Do all of the Switches toggle correctly between pressed and released?All
Ye s®Go To 3
No®Go To 25
266
SPEED CONTROL
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition On, Engine Not Running
Press the S/C ON/OFF button to select S/C ªON.º
With the DRB, monitor the Speed Control Switch inputs.
While observing display, press the Set Switch several times.
Does the DRB show the Set Switch pressed and released?All
Ye s®Go To 4
No®Replace the Speed Control On/Off/Set Switch.
Perform Powertrain Verification Test VER-4A.
4 Ignition On, Engine Not Running
With the DRB, monitor the Speed Control Switch inputs.
While observing display, press the Brake Pedal several times.
Does the DRB show Brake Switch Status change between pressed and released?All
Ye s®Go To 5
No®Refer to symptom SPEED CONTROL BRAKE SWITCH OUT-
PUT in the SPEED CONTROL category.
5 Ignition On, Engine Not Running
With the DRB, monitor the Speed Control Switch inputs.
While observing the display, move the Gear Selector to Drive.
Does the DRB show the Park/Neutral Switch in D/R?All
Ye s®Go To 6
No®Refer to symptom CHECKING PARK/NEUTRAL POS SWITCH
in the SPEED CONTROL category.
6 Ignition Off
Disconnect the Speed Control Servo Connector.
Note: Check connectors - Clean/repair as necessary.
Turn the Ignition on and the S/C on.
Using a Voltmeter measure voltage of the S/C Brake Switch Output Ckt at Servo
Conn.
Is the voltage above 10 volts?All
Ye s®Go To 7
No®Go To 14
7 Ignition Off
Start engine, allow to idle 1 minute.
Turn Engine off, (Ignition on).
With the DRB, actuate the Speed Control Servo Solenoids.
Does the Throttle open and close?All
Ye s®Refer to symptom SPEED CONTROL DENIED MESSAGE in the
SPEED CONTROL category.
No®Go To 8
8 Ignition Off
Inspect the Speed Control Throttle Cable.
Is the Cable disconnected or damaged?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-4A.
No®Go To 9
267
SPEED CONTROL
* CHECKING SPEED CONTROL OPERATION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
9 Ignition Off
Disconnect the Vacuum Supply to the Speed Control Servo.
Attach a Vacuum Gauge to the disconnected hose.
Start engine.
Does the Vacuum Gauge read Manifold Vacuum?All
Ye s®Go To 10
No®Repair the Vacuum Supply for a leak or restriction.
Perform Powertrain Verification Test VER-4A.
10 Ignition Off
Disconnect the Speed Control Servo Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter measure the Ground Circuit from Servo Connector to gnd.
Is the resistance below 5.0 ohms?All
Ye s®Go To 11
No®Repair the open Ground Circuit.
Perform Powertrain Verification Test VER-4A.
11 Ignition Off
Disconnect the Speed Control Servo Connector.
Note: Check connectors - Clean/repair as necessary.
Is any Terminal damaged, pushed out or miswired?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-4A.
No®Go To 12
12 Disconnect the vacuum supply from the Speed Control Servo.
Attach a vacuum gauge to the vacuum hose.
Start the Engine, allow to idle for 1 minute.
Turn engine off.
Observe Vacuum Gauge for 10 seconds.
Does the Vacuum hold for at least 10 seconds?All
Ye s®Go To 13
No®Replace the Vacuum Reservoir.
Perform Powertrain Verification Test VER-4A.
13 If there are no potential causes remaining, the S/C Servo is assumed to be defective.
View repair options.All
Repair
Replace the Speed Control Servo.
Perform Powertrain Verification Test VER-4A.
14 Ignition Off
Disconnect the Speed Control Servo Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter measure the Ground Circuit from Servo Connector to gnd.
Is the resistance below 5.0 ohms?All
Ye s®Go To 15
No®Repair the open Ground Circuit.
Perform Powertrain Verification Test VER-4A.
268
SPEED CONTROL
* CHECKING SPEED CONTROL OPERATION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
25 Ignition On.
With the DRB Select ªInputs/Outputsº, monitor the S/C Switch.
Press and hold each switch to see change in the parameter.
Does the parameter change for each switch?All
Ye s®Go To 26
No®Replace the S/C Switch.
Perform Powertrain Verification Test VER-4A.
26 Ignition On, Engine Not Running
With the DRB, monitor the Speed Control Switch inputs.
While observing display, press the Set Switch several times.
Does the DRB show the Set Switch pressed and released?All
Ye s®Go To 27
No®Replace the Speed Control On/Off/Set Switch.
Perform Powertrain Verification Test VER-4A.
27 If there are no potential causes remaining, the Clock Spring is assumed to be
defective.
View repair options.All
Repair
Replace Clock Spring.
Perform Powertrain Verification Test VER-4A.
271
SPEED CONTROL
* CHECKING SPEED CONTROL OPERATION ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
9 Ignition Off.
Connect the DRB to a functional Data Link Connector on another vehicle.
Turn the ignition on.
With the DRB, attempt to read trouble codes.
Did the DRB display ªNo Responseº?All
Ye s®Go To 10
No®Replace the initial vehicle's Powertrain Control Module.
Perform Powertrain Verification Test VER-1A.
10 Ignition Off.
Substitute another DRB Adapter Cable.
Ignition on, Engine not running.
With the DRB, attempt to read trouble codes.
Did the DRB display ªNo Responseº?All
Ye s®Go To 11
No®Replace the DRB Adapter Cable.
Perform Powertrain Verification Test VER-1A.
11 If there are no potential causes remaining, the Diagnostic Readout Box is assumed to
be defective.
View repair options.All
Repair
Have the DRB repaired or replaced.
Perform Powertrain Verification Test VER-1A.
12 Ignition Off.
Disconnect the TP Sensor Connector.
Note: Check connector-Clean/repair as necessary.
Turn the ignition on.
With a voltage, measure the Throttle Position Sensor 5±volt Supply circuit.
Is the voltage above 6.0 volts?All
Ye s®Repair the open grounds at the Powertrain Control Module
Cavities 10 and 50.
Perform the Powertrain Verification Test VER-1A
No®Go To 13
13 Ignition Off.
Disconnect the Powertrain Control Module.
Note: Check connector-Clean/repair as necessary.
Turn the ignition on.
With a voltmeter, measure Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 14
No®Repair the open Fused Ignition Switch Output Circuit (check
Ignition Switch Fuse in PDC).
Perform Powertrain Verification Test VER-1A.
274
STARTING
*(NO RESPONSE(CONDITION ÐContinued
ProCarManuals.com

Symptom:
* CHECKING THE CAM AND CRANK SENSORS
POSSIBLE CAUSES
SECONDARY INDICATORS PRESENT
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
Note: Address all trouble codes before continuing.
Note: Ensure PCM Connectors are secure.
With the DRB, read the secondary indicators while cranking the engine.
Were there any secondary indicators present while cranking the engine?All
Ye s®Refer to Symptom list for further diagnostic test.
No®Go To 2
2 Ignition On, Engine Not Running
With the DRB in Input/Output display, monitor the current CMP and CKP states.
Crank the engine for at least 15 seconds.
Does the DRB show current CKP state9present9while cranking?All
Ye s®Go To 3
No®Refer to symptom P-0340 NO CRANK REFERENCE SIGNAL AT
PCM in the DRIVEABILITY category.
3 Ignition On, Engine Not Running
With the DRB in Input/Output display, monitor the current CMP and CKP states.
Crank the engine for at least 15 seconds.
Does the DRB show current CMP state9present9while cranking?All
Ye s®Refer to symptom * CHECKING THE SECONDARY IGNITION
SYSTEM in the STARTING category.
No®Refer to symptom P-0340 NO CAM SIGNAL AT PCM in the
DRIVEABILITY category.
276
STARTING
ProCarManuals.com

Symptom:
* CHECKING THE ENGINE MECHANICAL SYSTEMS
POSSIBLE CAUSES
ENGINE COMPRESSION OUT OF SPECIFICATION
VALVE TIMING OUT OF SPECIFICATION
POWERTRAIN CONTROL MODULE DEFECTIVE
CLEAN SPARK PLUGS
SPARK PLUG CABLES POSITIONED INCORRECTLY
TEST ACTION APPLICABILITY
1 Turn Ignition off.
Inspect Spark Plug Cables for correct placement.
Are all Spark Plug Cables positioned correctly?All
Ye s®Go To 2
No®Reinstall Spark Plug Cables as necessary.
2 Turn Ignition off.
Remove all Spark Plugs and inspect the tips for wet fuel.
Are the Spark Plug tips wet?All
Ye s®Clean the spark plugs.
No®Go To 3
3 Turn Ignition off.
Using service information procedures, check Engine compression.
Is Engine compression within specifications?All
Ye s®Go To 4
No®Repair the Engine as necessary.
Perform Verification Test VER-1A.
4 Turn Ignition off.
Using service information procedures, check Engine Valve timing.
Is Valve timing within specifications?All
Ye s®Go To 5
No®Repair Valve timing as necessary.
Perform Verification Test VER-1A.
5 If there are no potential causes or DTCs remaining, the Powertrain Control Module
is assumed to be defective.
View repair options.All
Repair
Replace the Powertrain Control Module.
Perform Powertrain Verification Test VER-1A.
277
STARTING
ProCarManuals.com

TEST ACTION APPLICABILITY
1Note: Ensure the SKIM has proper communication and that there are no
SKIM DTC's present before continuing.
Ignition Off.
Ensure the Throttle Cables are not holding the Throttle open.
Is the Throttle held open?ENGINE - 3.0L V6
Ye s®Repair condition that holds the Throttle Body open.
Perform Powertrain Verification Test VER-1A.
No®Go To 2
2 Ignition On, Engine Not Running
With the DRB, actuate the Fuel System and check for Fuel Pump operation at the
Fuel Tank.
Is the Fuel Pump operating?ENGINE - 3.0L V6
Ye s®Go To 3
No®Go To 13
3 Ignition On, Engine Not Running
With DRB, read Throttle Position Sensor voltage.
Is the voltage above 1.5 volts?ENGINE - 3.0L V6
Ye s®Disconnect the TP Sensor Conn. Replace Throttle Position Sensor.
Perform Powertrain Verification Test VER-1A.
No®Go To 4
4 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Relieve Fuel pressure.
Install a Fuel Pressure Gauge to the Fuel Rail.
Note: The Fuel Tank must be at least 1/4 full for the following tests.
Ignition On, Engine Not Running.
With the DRB, actuate the Fuel System.
Read the Fuel Pressure Gauge.
Fuel pressure should be 43 to 53 psi for Gasoline.
Is the Fuel pressure above the specification ?ENGINE - 3.0L V6
Ye s®Go To 5
No®Go To 8
5 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Filter for a restriction.
Is there a restriction?ENGINE - 3.0L V6
Ye s®Replace the Fuel Filter.
Perform Powertrain Verification Test VER-1A.
No®Go To 6
279
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
6 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Filter for a restriction.
Is there a restriction?ENGINE - 3.0L V6
Ye s®Go To 7
No®Replace the Fuel Pressure Regulator.
Perform Powertrain Verification Test VER-1A.
7 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release the Fuel pressure.
Inspect Fuel Return Tube for restriction between fuel Filter and Fuel Pump Module.
Is there a restriction?ENGINE - 3.0L V6
Ye s®Replace restricted Fuel Tube.
Perform Powertrain Verification Test VER-1A.
No®Test Complete.
8 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Relieve Fuel pressure.
Tee-In a Fuel Pressure Gauge into the Fuel Hose using tool #6433.
Note: The Fuel Tank must be at least 1/4 full for the following tests.
Ignition On, Engine Not Running.
With the DRB, actuate the Fuel System.
Read the Fuel Pressure Gauge.
Fuel pressure should be 43 to 53 psi for Gasoline.
Is the Fuel pressure below the specification ?ENGINE - 3.0L V6
Ye s®Go To 9
No®Test Complete.
9 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove adapter 6631 and reinstall Fuel Line.
Install adapter 6631 between Fuel Pump and Fuel Filter.
Connect Fuel Pressure Gauge to adapter 6631.
Key on.
With the DRB, actuate Fuel System.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 3.0L V6
Ye s®Replace the Fuel Filter.
Perform Powertrain Verification Test VER-1A.
No®Go To 10
280
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
10 Ignition Off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pump Module.
Inspect the Fuel Pump Inlet Strainer.
Is the Inlet Strainer plugged?ENGINE - 3.0L V6
Ye s®Replace the Fuel Inlet Strainer.
Perform Powertrain Verification Test VER-1A.
No®Go To 11
11 Record the Fuel Pressure Gauge reading.
Ignition key off.
Warning: The Fuel System must be opened and may be under high pressure.
Release Fuel pressure.
Remove the Fuel Pressure Gauge.
Remove Fuel Pressure Gauge Adapter 6433 and reconnect Fuel Line to Fuel Rail.
Install adapter 6631 between Fuel Filter Outlet and Chassis Fuel Supply Tube.
Connect Fuel Pressure Gauge to adapter 6631.
Ignition On, Engine Not Running.
With DRB, actuate the ASD Fuel System.
Record the Fuel Pressure Gauge reading.
Compare this reading with the previous reading.
Is the fuel pressure at least 2 psi higher than the previous reading?ENGINE - 3.0L V6
Ye s®Repair restriction in Chassis Fuel Supply Line between Fuel
Filter and Fuel Rail.
Perform Powertrain Verification Test VER-1A.
No®Go To 12
12 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.ENGINE - 3.0L V6
Repair
Replace Fuel Pump Module.
Perform Powertrain Verification Test VER-1A.
13 Ignition On, Engine Not Running
With DRB, read Throttle Position Sensor voltage.
Is the voltage above 1.5 volts?ENGINE - 3.0L V6
Ye s®Disconnect the TP Sensor Conn. Replace Throttle Position Sensor.
Perform Powertrain Verification Test VER-1A.
No®Go To 14
14 Ignition Off.
Disconnect the Fuel Pump Harness Connector.
Note: Check connectors - Clean/repair as necessary.
Caution: It is critical that the Fuel Pump Connector has a clean and tight
connection.
With an Ohmmeter, measure the Fuel Pump Ground Circuit.
Is the resistance below 5.0 ohms?ENGINE - 3.0L V6
Ye s®Go To 15
No®Repair the open Fuel Pump Ground Circuit.
Perform Powertrain Verification Test VER-1A.
281
STARTING
* CHECKING THE FUEL SYSTEM ÐContinued
ProCarManuals.com