remote control CHRYSLER VOYAGER 2004 Repair Manual
[x] Cancel search | Manufacturer: CHRYSLER, Model Year: 2004, Model line: VOYAGER, Model: CHRYSLER VOYAGER 2004Pages: 2585, PDF Size: 62.54 MB
Page 2439 of 2585
(5) Pull the air filter straight down and out of the
HVAC housing (Fig. 2).
INSTALLATION
(1) Note the ªAirflowº directional arrow imprinted
on the foam seal around the frame of the air filter.
This arrow should always be oriented towards the
center of the vehicle.
(2) With the air filter ªAirflowº arrow properly ori-
ented, carefully slide the filter fully upward into the
HVAC housing through the air filter opening.
(3) With the latch still positioned against its
opened stop, reinstall the air filter door onto the
lower HVAC housing air filter opening.
(4) Slide the air filter door latch toward the front
of the vehicle until it hits the closed stop on the door.
AIR OUTLETS
DESCRIPTION
Based upon the system mode selected, conditioned
air can exit the front HVAC housing through one or a
combination of the four main housing outlets: defrost,
demist, panel, or floor. Once the conditioned air exits
the unit housing, it is directed through molded plas-
tic ducts to the various outlets in the vehicle interior.
These outlets and their locations are as follows:
²Defroster Outlet- A single, centrally mounted
outlet delivers air for defrosting the large windshield.
Because outlet vanes are not needed to direct flow, a
simple, integral grid is molded into the center of the
instrument panel top cover to prevent objects from
falling into the duct. If the defroster outlet is faultyor damaged, the instrument panel top cover must be
replaced.
²Demister Outlets- There are two side window
demisters that aid in defogging and defrosting the
front door windows. One demister outlet is located at
each outboard end of the instrument panel top pad,
near the belt line at the A-pillars. The demister out-
lets can be removed from the top pad individually for
service replacement.
²Instrument Panel Outlets- There are five
panel outlets in the instrument panel, one located
near each outboard end of the instrument panel fac-
ing the rear of the vehicle, and three located near the
top of the instrument panel center bezel. On models
with manual temperature control, all five of these
outlets are fully adjustable. On models with Auto-
matic Temperature Control (ATC) system, the center
outlet in the center bezel has fixed vanes because it
also houses the remote infrared temperature sensors
for the front seat positions. The outboard outlets can
be removed individually for service replacement. The
center bezel outlets are serviced as a gang of three
outlets and, on models with ATC, also includes the
infrared sensors.
²Front Door Rear Outlets- A fully adjustable
outlet located at the rear of each front door trim
panel supplies only cooled air to the intermediate
seat passengers. Air is supplied to these outlets from
the instrument panel through ducts in the doors that
use molded seals at the instrument panel to prevent
air leakage. The door ducts are integral to the front
door trim panels. These outlets also incorporate a red
reflector to improve the safety and visibility of an
opened front door to traffic approaching the vehicle
from the rear at night. These outlets can be removed
from the door trim panels for service replacement.
²Front Floor Outlets- There are two front floor
outlets, one located above each side of the floor panel
center tunnel below the instrument panel. These out-
lets are integral to the front HVAC distribution hous-
ing.
²Rear Floor Outlets- Wide rear floor outlets
located under each front seat have integral, fixed
directional dividers to distribute heated air across
the floor for intermediate seat passengers. These out-
lets are integral to the floor distribution ducts routed
under the front floor carpet from an outlet nozzle on
the bottom of the front HVAC distribution housing.
REMOVAL
REMOVAL - CENTER BEZEL OUTLETS
The three outlets located near the top of the
instrument panel center bezel are serviced only as a
set of all three outlets. If the vehicle is equipped with
the optional automatic temperature control (ATC)
Fig. 2 Air Filter Door - Typical
1 - AIR FILTER DOOR
2-LATCH
3 - CLOSED STOP
4 - LOWER HVAC HOUSING
5 - OPENED STOP
24 - 44 DISTRIBUTION - FRONTRS
AIR FILTER (Continued)
Page 2441 of 2585
(2) Engage the retainer features on the top of the
outlet housing with their receptacles at the top of the
center bezel, then roll the bottom of the outlet hous-
ing downwards towards the center bezel.
(3) Install the three screws that secure the bottom
of the outlet housing to the center bezel. Tighten the
screws to 2 N´m (17 in. lbs.).
(4) If the vehicle is equipped with the optional
ATC system, reconnect the ATC remote infrared tem-
perature sensor jumper harness to the sensor connec-
tor receptacle located on the bottom of the center
outlet housing.
(5) Reinstall the center bezel onto the instrument
panel (Refer to 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL - INSTAL-
LATION).
(6) Reconnect the battery negative cable.
INSTALLATION - DEMISTER OUTLET
(1) Position the demister outlet over the demister
duct opening in the instrument panel top pad.
(2) Using hand pressure, press the demister outlet
firmly and evenly into the instrument panel top pad
opening until the snap features on the outlet are
fully engaged.
INSTALLATION - INSTRUMENT PANEL OUTLET
(1) Position the instrument panel outlet into the
panel duct opening in the instrument panel top pad.
(2) Using hand pressure, press the instrument
panel outlet firmly and evenly into the instrument
panel top pad opening until the snap features on the
outlet are fully engaged.
BLOWER MOTOR
DESCRIPTION
The blower motor is a 12-volt, Direct Current (DC)
motor with a squirrel cage-type blower wheel that is
secured to the blower motor shaft (Fig. 6). The
blower motor and wheel are located near the passen-
ger side end of the HVAC housing in the passenger
compartment below the instrument panel. The
blower motor and blower motor wheel are factory bal-
anced and cannot be adjusted or repaired. If faulty or
damaged, the blower motor and blower wheel must
be replaced as an assembly.
OPERATION
On models equipped with the manual heater-A/C
system, the blower motor will operate whenever the
ignition switch is in the On position and the blower
control switch is in any position except Off. On mod-
els equipped with the Automatic Temperature Con-
trol (ATC) system, the blower motor will operate
whenever the ignition switch is in the On position
and the A/C-heater control power is turned on.
The blower motor receives battery current when-
ever the front blower motor relay is energized. The
front blower motor relay output circuit is protected
by a fuse in the Integrated Power Module (IPM)
located in the engine compartment near the battery.
In the manual heater-A/C system, the blower motor
speed is controlled by regulating the path to ground
through the blower control switch and the blower
motor resistor. In the ATC system, the blower motor
speed is controlled by an electronic blower motor
power module, which uses a pulse width modulated
input from the ATC module and feedback from the
Fig. 5 Instrument Panel Outlet - Left Side Shown
1 - INSTRUMENT PANEL TOP PAD
2 - INSTRUMENT PANEL OUTLET
3 - TRIM STICK
Fig. 6 Blower Motor
1 - BLOWER MOTOR
2 - RUBBER GROMMET
3 - BLOWER MOTOR CONNECTOR
4 - MOUNTING TABS
24 - 46 DISTRIBUTION - FRONTRS
AIR OUTLETS (Continued)
Page 2556 of 2585
ENGINE OIL LEVEL CHECK, STANDARD
PROCEDURE.........................9-53
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING.......................9-136
ENGINE OIL PRESSURE - DIAGNOSIS
AND TESTING, CHECKING...............9-52
ENGINE, SPECIAL TOOLS - 2.4L..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L.......9-95
ENGINE, SPECIFICATIONS - 3.3/3.8L . . 9-91,9s-11
ENGINE SPEED SENSOR - DESCRIPTION . . 14-26
ENGINE SPEED SENSOR - OPERATION....14-26
ENGINES - DESCRIPTION, ENGINE OIL -
DIESEL..............................0-6
ENGINES - DIAGNOSIS AND TESTING,
SYSTEM CHARGE LEVEL TEST -
GASOLINE..........................24-67
ENGINES - EXPORT - DESCRIPTION,
DIESEL.............................0-24
ENTRY MODULE - DESCRIPTION,
REMOTE KEYLESS...................8N-43
ENTRY MODULE - DESCRIPTION,
SENTRY KEY REMOTE.................8Q-3
ENTRY MODULE - DIAGNOSIS AND
TESTING, REMOTE KEYLESS...........8N-43
ENTRY MODULE - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-5
ENTRY MODULE - INSTALLATION,
REMOTE KEYLESS...................8N-44
ENTRY MODULE - INSTALLATION,
SENTRY KEY REMOTE.................8Q-6
ENTRY MODULE - OPERATION, REMOTE
KEYLESS...........................8N-43
ENTRY MODULE - OPERATION, SENTRY
KEY REMOTE........................8Q-4
ENTRY MODULE - REMOVAL, REMOTE
KEYLESS...........................8N-44
ENTRY MODULE - REMOVAL, SENTRY
KEY REMOTE........................8Q-5
ENTRY SYSTEM - DIAGNOSIS AND
TESTING, SENTRY KEY REMOTE.........8Q-3
ENTRY TRANSMITTER - DIAGNOSIS AND
TESTING, KEYLESS..............8N-42,8N-5
ENTRY TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE, REMOTE
KEYLESS............................8N-5
EQUIPMENT - STANDARD PROCEDURE,
REFRIGERANT SYSTEM SERVICE........24-70
ERASING TRANSMITTER CODES -
STANDARD PROCEDURE..............8M-11
EVACUATE - STANDARD PROCEDURE,
REFRIGERANT SYSTEM...............24-72
EVAP CANISTER - INSTALLATION, REAR . . 25-20
EVAP CANISTER - REMOVAL, REAR......25-19
EVAPORATION CONTROL SYSTEM -
OPERATION.........................25-10
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-97
EVAPORATOR - INSTALLATION, A/C......24-80
EVAPORATOR - INSTALLATION, REAR
A/C................................24-99
EVAPORATOR - OPERATION, A/C . . . 24-80,24-97
EVAPORATOR - REMOVAL, A/C..........24-80
EVAPORATOR - REMOVAL, REAR A/C.....24-97
EVAPORATOR LINE EXTENSION -
INSTALLATION, REAR A/C..............24-99
EVAPORATOR LINE EXTENSION -
REMOVAL, A/C......................24-98
EVAPORATOR TEMPERATURE SENSOR -
DESCRIPTION.......................24-27
EVAPORATOR TEMPERATURE SENSOR -
OPERATION.........................24-28
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-12
EVAP/PURGE SOLENOID - INSTALLATION . 25-12
EVAP/PURGE SOLENOID - OPERATION....25-12
EVAP/PURGE SOLENOID - REMOVAL.....25-12
EXCESSIVE EXHAUST SYSTEM NOISE -
DIAGNOSIS AND TESTING..............11-2
EXHAUST MANIFOLD - CLEANING........9-61
EXHAUST MANIFOLD - INSPECTION.......9-61
EXHAUST MANIFOLD - INSTALLATION.....9-61
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-152
EXHAUST MANIFOLD - LEFT -
INSPECTION
........................9-152
EXHAUST MANIFOLD - LEFT -
INSTALLATION
.......................9-152
EXHAUST MANIFOLD - LEFT - REMOVAL
. . 9-152
EXHAUST MANIFOLD - REMOVAL
.........9-61
EXHAUST MANIFOLD - RIGHT -
CLEANING
..........................9-151EXHAUST MANIFOLD - RIGHT -
INSPECTION........................9-151
EXHAUST MANIFOLD - RIGHT -
INSTALLATION.......................9-151
EXHAUST MANIFOLD - RIGHT -
REMOVAL..........................9-150
EXHAUST SYSTEM - DESCRIPTION.......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS
AND TESTING, EXCESSIVE..............11-2
EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING.............11-2
EXHAUST SYSTEM, SPECIAL TOOLS......11-4
EXHAUST TUBE - INSTALLATION.......24-115
EXHAUST TUBE - REMOVAL...........24-114
EXHAUSTER - DESCRIPTION, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXHAUSTER - INSTALLATION, REAR
QUARTER PANEL/FENDER AIR..........23-58
EXHAUSTER - REMOVAL, REAR
QUARTER PANEL/FENDER AIR..........23-57
EXPANSION VALVE - DESCRIPTION......24-81
EXPANSION VALVE - DESCRIPTION, A/C . . 24-99
EXPANSION VALVE - DIAGNOSIS AND
TESTING..........................24-100
EXPANSION VALVE - DIAGNOSIS AND
TESTING, A/C.......................24-81
EXPANSION VALVE - INSTALLATION......24-82
EXPANSION VALVE - INSTALLATION, A/C . 24-100
EXPANSION VALVE - OPERATION........24-81
EXPANSION VALVE - OPERATION, A/C....24-99
EXPANSION VALVE - REMOVAL.........24-82
EXPANSION VALVE - REMOVAL, A/C.....24-100
EXPORT - BRAKE ROTOR..........5-55,5s-58
EXPORT - DESCRIPTION...........5-58,5s-60
EXPORT - DESCRIPTION................0-15
EXPORT - DESCRIPTION................2-10
EXPORT - DESCRIPTION, ANTENNA
MODULE............................8A-6
EXPORT - DESCRIPTION, DIESEL
ENGINES............................0-24
EXPORT - DESCRIPTION, DOOR
CYLINDER LOCK SWITCH...............8N-3
EXPORT - DESCRIPTION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - DESCRIPTION, QUARTER
GLASS INTEGRAL ANTENNA.............8A-9
EXPORT - DIAGNOSIS AND TESTING,
ANTENNA MODULE....................8A-7
EXPORT - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK SWITCH.........8N-3
EXPORT - DIAGNOSIS AND TESTING,
QUARTER GLASS INTEGRAL ANTENNA....8A-9
EXPORT - INSTALLATION...............2-11
EXPORT - INSTALLATION, ANTENNA
MODULE............................8A-7
EXPORT - INSTALLATION, DOOR
CYLINDER LOCK SWITCH...............8N-4
EXPORT - INSTALLATION, HEADLAMP
UNIT..............................8L-17
EXPORT - INSTALLATION, HOOD AJAR
SWITCH............................8Q-3
EXPORT - INSTALLATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-49
EXPORT - OPERATION, ANTENNA
MODULE............................8A-6
EXPORT - OPERATION, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - OPERATION, POWER
FOLDAWAY MIRROR SWITCH..........8N-48
EXPORT - OPERATION, QUARTER GLASS
INTEGRAL ANTENNA...................8A-9
EXPORT - REMOVAL...................2-11
EXPORT - REMOVAL, ANTENNA MODULE . . 8A-7
EXPORT - REMOVAL, DOOR CYLINDER
LOCK SWITCH........................8N-3
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR
SWITCH............................8Q-3
EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR SWITCH
..........8N-48
EXPORT - STANDARD PROCEDURE,
FRONT FOG LAMP UNIT ALIGNMENT
......8L-9
EXPORT - STANDARD PROCEDURE,
HEADLAMP UNIT ALIGNMENT
..........8L-14
EXTENSION - INSTALLATION, REAR A/C
EVAPORATOR LINE
...................24-99
EXTENSION - REMOVAL, A/C
EVAPORATOR LINE
...................24-98EXTENSION TRIM - INSTALLATION,
A-PILLAR LOWER....................23-74
EXTENSION TRIM - REMOVAL, A-PILLAR
LOWER............................23-74
EXTERIOR - DESCRIPTION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - OPERATION, LAMPS/
LIGHTING...........................8L-2
EXTERIOR - WARNING, LAMPS/
LIGHTING...........................8L-3
EXTERIOR HANDLE - INSTALLATION.....23-22,
23-40
EXTERIOR HANDLE - REMOVAL....23-21,23-40
EXTERIOR HANDLE SWITCH -
DESCRIPTION.......................8N-11
EXTERIOR HANDLE SWITCH -
INSTALLATION......................8N-12
EXTERIOR HANDLE SWITCH -
OPERATION.........................8N-11
EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-11
EXTERIOR LAMPS, SPECIFICATIONS......8L-3
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - ADHESIVE
ATTACHED - REMOVAL................23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - INSTALLATION............23-51
EXTERIOR NAME PLATES - TAPE
ATTACHED - REMOVAL................23-51
FACTOR SETTING - STANDARD
PROCEDURE, PINION............8E-15,8E-23
FAILED PARK SWITCH - DIAGNOSIS AND
TESTING..............................8R-2
FAN - DESCRIPTION, RADIATOR..........7-28
FAN - INSTALLATION, RADIATOR.........7-30
FAN - OPERATION, RADIATOR...........7-29
FAN - REMOVAL, RADIATOR.............7-30
FAN MOTOR - DIAGNOSIS AND
TESTING, RADIATOR...................7-29
FAN RELAY - DESCRIPTION, RADIATOR....7-30
FAN RELAY - INSTALLATION, RADIATOR . . . 7-30
FAN RELAY - OPERATION, RADIATOR......7-30
FAN RELAY - REMOVAL, RADIATOR.......7-30
FASCIA - INSTALLATION, FRONT.........13-1
FASCIA - INSTALLATION, REAR..........13-2
FASCIA - REMOVAL, FRONT.............13-1
FASCIA - REMOVAL, REAR..............13-2
FASCIA - SCUFF PAD - INSTALLATION,
REAR...............................13-4
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-2
FASTENER TORQUE, SPECIFICATIONS -
ABS ................................5-79
FASTENER TORQUE, SPECIFICATIONS -
BRAKE...........................5-9,5s-8
FASTENER TORQUE, SPECIFICATIONS -
FRONT SUSPENSION...................2-3
FASTENER TORQUE, SPECIFICATIONS -
POWER STEERING....................19-9
FASTENER TORQUE, SPECIFICATIONS -
REAR SUSPENSION...................2-28
FASTENER USAGE - DESCRIPTION......Intro.-5
FEED CIRCUIT RESISTANCE TEST -
DIAGNOSIS AND TESTING.........8F-32,8F-34
FEED CIRCUIT TEST - DIAGNOSIS AND
TESTING
......................8F-33,8F-35
FENDER - INSTALLATION, FRONT
........23-52
FENDER - REMOVAL, FRONT
...........23-52
FILL - DIAGNOSIS AND TESTING,
VEHICLE DOES NOT
..................25-16
FILL - STANDARD PROCEDURE, FLUID
DRAIN
.............................21-71
FILL DOOR - INSTALLATION, FUEL
.......23-52
FILL DOOR - REMOVAL, FUEL
..........23-52
FILL DOOR BLOCKER LATCH -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LATCH STRIKER -
INSTALLATION, FUEL
.................23-53
FILL DOOR BLOCKER LATCH STRIKER -
REMOVAL, FUEL
.....................23-53
FILL DOOR BLOCKER LOCKOUT LINK -
INSTALLATION, FUEL
.................23-54
FILL DOOR BLOCKER LOCKOUT LINK -
REMOVAL, FUEL
.....................23-53
RSINDEX13
Description Group-Page Description Group-Page Description Group-Page
Page 2561 of 2585
INBOARD - 50/50 BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-13
INBOARD - INSTALLATION, SEAT BELT
BUCKLE - FRONT....................8O-12
INBOARD - QUAD BUCKET -
INSTALLATION, SEAT BELT BUCKLE -
FIRST ROW.........................8O-12
INBOARD - QUAD BUCKET - REMOVAL,
SEAT BELT BUCKLE - FIRST ROW.......8O-12
INBOARD - REMOVAL, SEAT BELT
BUCKLE - FRONT....................8O-12
INDICATOR LAMP - DESCRIPTION,
VTSS/SKIS..........................8Q-7
INDICATOR LAMP - OPERATION,
VTSS/SKIS..........................8Q-8
INDICATORS - DIAGNOSIS AND
TESTING, TREAD WEAR..........22-16,22s-8
INFLATION PRESSURES - STANDARD
PROCEDURE, TIRE..............22-16,22s-8
INFO CENTER - DESCRIPTION,
ELECTRONIC VEHICLE.................8M-6
INFO CENTER - INSTALLATION,
ELECTRONIC VEHICLE.................8M-9
INFO CENTER - OPERATION,
ELECTRONIC VEHICLE.................8M-7
INFO CENTER - REMOVAL, ELECTRONIC
VEHICLE............................8M-9
INFRARED TEMPERATURE SENSOR -
DESCRIPTION.......................24-29
INFRARED TEMPERATURE SENSOR -
OPERATION.........................24-29
INITIAL OPERATION - STANDARD
PROCEDURE, POWER STEERING
PUMP.............................19-37
INJECTION SYSTEM - OPERATION.......14-18
INJECTOR - DESCRIPTION, FUEL........14-26
INJECTOR - OPERATION, FUEL..........14-26
INLET AIR TEMPERATURE SENSOR -
DESCRIPTION.......................14-30
INLET FILTER - INSTALLATION..........14-13
INLET FILTER - REMOVAL..............14-13
INLET HOSE - INSTALLATION, HEATER....24-86
INLET HOSE - REMOVAL, HEATER.......24-85
INLET TUBE - 2.4L - DESCRIPTION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - INSTALLATION,
WATER PUMP........................7-35
INLET TUBE - 2.4L - REMOVAL, WATER
PUMP..............................7-35
INLET TUBE - 3.3/3.8L - INSTALLATION,
WATER PUMP........................7-36
INLET TUBE - 3.3/3.8L - REMOVAL,
WATER PUMP........................7-36
INNER - INSTALLATION, CV BOOT.........3-6
INNER - REMOVAL, CV BOOT.............3-6
INNER BELT MOLDING - INSTALLATION,
FRONT DOOR......................23-115
INNER BELT MOLDING - REMOVAL,
FRONT DOOR......................23-115
INNER SEAL - INSTALLATION, HALF
SHAFT.............................21-12
INNER SEAL - REMOVAL, HALF SHAFT . . . 21-12
INNER/OUTER - INSTALLATION, CV
BOOT...............................3-17
INNER/OUTER - REMOVAL, CV BOOT......3-15
INPUT - DESCRIPTION, SPEED SENSOR . 21-239,
21s-140
INPUT - INSTALLATION, SPEED
SENSOR....................21-240,21s-141
INPUT - OPERATION, DATA BUS
COMMUNICATION RECEIVE - PCM.......8E-15
INPUT - OPERATION, IGNITION SENSE -
PCM...............................8E-15
INPUT - OPERATION, SENSOR RETURN -
PCM...............................8E-15
INPUT - OPERATION, SPEED SENSOR . . . 21-240,
21s-140
INPUT - REMOVAL, SPEED SENSOR....21-240,
21s-141
INPUT CLUTCH ASSEMBLY - ASSEMBLY . 21-216,
21s-116
INPUT CLUTCH ASSEMBLY -
DISASSEMBLY...............21-208,21s-107
INPUT FLANGE SEAL - INSTALLATION
.....3-45
INPUT FLANGE SEAL - REMOVAL
.........3-44
INPUT SHAFT - ASSEMBLY
........21-96,21s-5
INPUT SHAFT - DESCRIPTION
.....21-93,21s-1
INPUT SHAFT - DISASSEMBLY
.....21-93,21s-1INPUT SHAFT COVER SEAL -
INSTALLATION.......................21-14
INPUT SHAFT COVER SEAL - REMOVAL . . . 21-13
INPUT SHAFT END SEAL -
INSTALLATION.......................21-16
INPUT SHAFT END SEAL - REMOVAL.....21-15
INPUT SHAFT SEAL - INSTALLATION.....21-18
INPUT SHAFT SEAL - REMOVAL.........21-17
INSIDE HANDLE ACTUATOR -
INSTALLATION.......................23-27
INSIDE HANDLE ACTUATOR - REMOVAL . . 23-27
INSIDE HANDLE CABLE - INSTALLATION . . 23-38
INSIDE HANDLE CABLE - REMOVAL......23-37
INSIDE LATCH HANDLE - INSTALLATION . . 23-34
INSIDE LATCH HANDLE - REMOVAL......23-34
INSPECT, INSPECTION...............21-114
INSTRUMENT CLUSTER - DESCRIPTION . . . 8J-1
INSTRUMENT CLUSTER - OPERATION.....8J-1
INSTRUMENT PANEL - INSTALLATION,
LOWER............................23-69
INSTRUMENT PANEL - REMOVAL,
LOWER............................23-69
INSTRUMENT PANEL ANTENNA CABLE -
INSTALLATION.......................8A-9
INSTRUMENT PANEL ANTENNA CABLE -
REMOVAL...........................8A-8
INSTRUMENT PANEL ASSEMBLY -
INSTALLATION.......................23-66
INSTRUMENT PANEL ASSEMBLY -
REMOVAL............................23-65
INSTRUMENT PANEL CENTER BEZEL -
INSTALLATION.......................23-68
INSTRUMENT PANEL CENTER BEZEL -
REMOVAL..........................23-68
INSTRUMENT PANEL DEMISTER DUCTS
- INSTALLATION.....................24-55
INSTRUMENT PANEL DEMISTER DUCTS
- REMOVAL.........................24-55
INSTRUMENT PANEL DUCTS -
INSTALLATION.......................24-55
INSTRUMENT PANEL DUCTS - REMOVAL . 24-55
INSTRUMENT PANEL END CAP -
INSTALLATION.......................23-68
INSTRUMENT PANEL END CAP -
REMOVAL..........................23-68
INSTRUMENT PANEL OUTLET -
INSTALLATION.......................24-46
INSTRUMENT PANEL OUTLET -
REMOVAL..........................24-45
INSTRUMENT PANEL TOP COVER -
INSTALLATION.......................23-69
INSTRUMENT PANEL TOP COVER -
REMOVAL..........................23-68
INSTRUMENT PANEL TOP PAD
ASSEMBLY - INSTALLATION............23-72
INSTRUMENT PANEL TOP PAD
ASSEMBLY - REMOVAL................23-71
INTAKE MANIFOLD - DESCRIPTION . . 9-144,9-58
INTAKE MANIFOLD - INSTALLATION,
LOWER............................9-149
INTAKE MANIFOLD - INSTALLATION,
UPPER.............................9-147
INTAKE MANIFOLD - LOWER -
CLEANING..........................9-148
INTAKE MANIFOLD - LOWER -
INSPECTION....................9-148,9-60
INTAKE MANIFOLD - LOWER -
INSTALLATION........................9-60
INTAKE MANIFOLD - LOWER - REMOVAL . . 9-60
INTAKE MANIFOLD - REMOVAL, LOWER . . 9-148
INTAKE MANIFOLD - REMOVAL, UPPER . . . 9-145
INTAKE MANIFOLD - UPPER -
INSPECTION.........................9-59
INTAKE MANIFOLD - UPPER -
INSTALLATION........................9-59
INTAKE MANIFOLD - UPPER - REMOVAL . . . 9-58
INTAKE MANIFOLD LEAKS - DIAGNOSIS
AND TESTING...................9-145,9-58
INTAKE MANIFOLD VACUUM PORT
REPAIR - STANDARD PROCEDURE.......9-145
INTAKE PIPE - INSTALLATION, AIR
......24-114
INTAKE PIPE - REMOVAL, AIR
.........24-113
INTAKE/EXHAUST VALVES & SEATS -
CLEANING
.................9-105,9-32,9s-22
INTAKE/EXHAUST VALVES & SEATS -
DESCRIPTION
..............9-104,9-32,9s-21
INTAKE/EXHAUST VALVES & SEATS -
INSPECTION
...................9-105,9s-22INTAKE/EXHAUST VALVES & SEATS -
INSTALLATION..................9-106,9s-23
INTAKE/EXHAUST VALVES & SEATS -
OPERATION....................9-104,9s-21
INTAKE/EXHAUST VALVES & SEATS -
REMOVAL.....................9-105,9s-22
INTEGRAL ANTENNA - EXPORT -
DESCRIPTION, QUARTER GLASS.........8A-9
INTEGRAL ANTENNA - EXPORT -
DIAGNOSIS AND TESTING, QUARTER
GLASS..............................8A-9
INTEGRAL ANTENNA - EXPORT -
OPERATION, QUARTER GLASS...........8A-9
INTEGRATED POWER MODULE -
DESCRIPTION.....................8W-97-2
INTEGRATED POWER MODULE -
INSTALLATION....................8W-97-3
INTEGRATED POWER MODULE -
OPERATION.......................8W-97-2
INTEGRATED POWER MODULE -
REMOVAL........................8W-97-2
INTERACTIVE SPEED CONTROL (4
SPEED EATX ONLY) - OPERATION........8P-2
INTERFACE (PCI) BUS, OPERATION -
PROGRAMMABLE COMMUNICATIONS....14-21
INTERIOR LAMPS, SPECIFICATIONS......8L-20
INTERLOCK - DESCRIPTION, IGNITION....19-17
INTERLOCK SOLENOID - DESCRIPTION,
SHIFT......................21-233,21s-133
INTERLOCK SOLENOID - DIAGNOSIS
AND TESTING, BRAKE/TRANSMISSION
SHIFT......................21-235,21s-135
INTERLOCK SOLENOID - INSTALLATION,
SHIFT.......................21-236,21s-136
INTERLOCK SOLENOID - OPERATION,
SHIFT......................21-233,21s-134
INTERLOCK SOLENOID - REMOVAL,
SHIFT......................21-235,21s-135
INTERLOCK SWITCH - INSTALLATION,
CLUTCH PEDAL.......................6-14
INTERLOCK SWITCH - REMOVAL,
CLUTCH PEDAL.......................6-13
INTERMEDIATE SHAFT - ASSEMBLY....21-107,
21s-17
INTERMEDIATE SHAFT - DESCRIPTION . . 21-100,
21s-9
INTERMEDIATE SHAFT - DISASSEMBLY . 21-100,
21s-10
INTERNATIONAL SYMBOLS -
DESCRIPTION......................Intro.-5
INTERNATIONAL SYMBOLS -
DESCRIPTION.........................0-1
INTRODUCTION - DIAGNOSIS AND
TESTING, ENGINE DIAGNOSIS........9-3,9-76
IOD FUSE - DESCRIPTION...........8W-97-3
IOD FUSE - OPERATION.............8W-97-3
JOINT - DESCRIPTION, LOWER BALL......2-10
JOINT - DIAGNOSIS AND TESTING,
LOWER BALL........................2-10
JOINT - OPERATION, LOWER BALL.......2-10
JOINT MOLDING - INSTALLATION, ROOF . . 23-58
JOINT MOLDING - REMOVAL, ROOF......23-58
JOUNCE BUMPER - DESCRIPTION........2-36
JOUNCE BUMPER - OPERATION..........2-36
JUMP STARTING - STANDARD
PROCEDURE.........................0-27
JUNCTION BLOCK - DESCRIPTION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - INSTALLATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - OPERATION,
NON-ABS.......................5-33,5s-32
JUNCTION BLOCK - REMOVAL, NON-ABS . . 5-33,
5s-32
KEY - DESCRIPTION, TRANSPONDER.....8Q-6
KEY - OPERATION, TRANSPONDER.......8Q-6
KEY IMMOBILIZER MODULE -
DESCRIPTION, SENTRY................8E-18
KEY IMMOBILIZER MODULE -
INSTALLATION, SENTRY
...............8E-19
KEY IMMOBILIZER MODULE -
OPERATION, SENTRY
.................8E-18
KEY IMMOBILIZER MODULE - REMOVAL,
SENTRY
............................8E-18
KEY REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY
................8Q-3
KEY REMOTE ENTRY MODULE -
DIAGNOSIS AND TESTING, SENTRY
.......8Q-5
18 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
Page 2562 of 2585
KEY REMOTE ENTRY MODULE -
INSTALLATION, SENTRY................8Q-6
KEY REMOTE ENTRY MODULE -
OPERATION, SENTRY..................8Q-4
KEY REMOTE ENTRY MODULE -
REMOVAL, SENTRY...................8Q-5
KEY REMOTE ENTRY SYSTEM -
DIAGNOSIS AND TESTING, SENTRY.......8Q-3
KEYLESS ENTRY MODULE -
DESCRIPTION, REMOTE...............8N-43
KEYLESS ENTRY MODULE - DIAGNOSIS
AND TESTING, REMOTE...............8N-43
KEYLESS ENTRY MODULE -
INSTALLATION, REMOTE..............8N-44
KEYLESS ENTRY MODULE - OPERATION,
REMOTE...........................8N-43
KEYLESS ENTRY MODULE - REMOVAL,
REMOTE...........................8N-44
KEYLESS ENTRY TRANSMITTER -
DIAGNOSIS AND TESTING.........8N-42,8N-5
KEYLESS ENTRY TRANSMITTER
PROGRAMMING - STANDARD
PROCEDURE, REMOTE.................8N-5
KEY/LOCK CYLINDER - DESCRIPTION....19-20
KEY/LOCK CYLINDER - INSTALLATION....19-20
KEY/LOCK CYLINDER - OPERATION......19-20
KEY/LOCK CYLINDER - REMOVAL.......19-20
KNOB - INSTALLATION, GEARSHIFT......21-87
KNOB - INSTALLATION, SEAT BELT
HEIGHT ADJUSTER...................8O-14
KNOB - REMOVAL, GEARSHIFT..........21-87
KNOB - REMOVAL, SEAT BELT HEIGHT
ADJUSTER.........................8O-14
KNOCK SENSOR - DESCRIPTION..........8I-8
KNOCK SENSOR - OPERATION...........8I-8
KNUCKLE - DESCRIPTION................2-6
KNUCKLE - INSPECTION, STEERING........2-9
KNUCKLE - INSTALLATION, STEERING......2-9
KNUCKLE - OPERATION.................2-7
KNUCKLE - REMOVAL, STEERING.........2-7
LABEL - DESCRIPTION, E-MARK......Intro.-11
LABEL - DESCRIPTION, VECI.........Intro.-11
LABEL - DESCRIPTION, VEHICLE
CERTIFICATION....................Intro.-11
LABEL - DESCRIPTION, VEHICLE
EMISSION CONTROL INFORMATION.......25-1
LAMP - DESCRIPTION, VTSS/SKIS
INDICATOR..........................8Q-7
LAMP - DIAGNOSIS AND TESTING,
FRONT FOG..........................8L-7
LAMP - INSTALLATION, CENTER
CONSOLE...........................8L-21
LAMP - INSTALLATION, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - INSTALLATION, COURTESY......8L-21
LAMP - INSTALLATION, DOME/CARGO....8L-22
LAMP - INSTALLATION, FRONT FOG.......8L-8
LAMP - INSTALLATION, LICENSE........8L-17
LAMP - INSTALLATION, LIFTGATE.......8L-22
LAMP - INSTALLATION, PARK/TURN
SIGNAL............................8L-18
LAMP - INSTALLATION, READING........8L-23
LAMP - INSTALLATION, TAIL...........8L-19
LAMP - INSTALLATION, VANITY.........8L-24
LAMP - OPERATION, VTSS/SKIS
INDICATOR..........................8Q-8
LAMP - REMOVAL, CENTER CONSOLE....8L-21
LAMP - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP - REMOVAL, COURTESY..........8L-21
LAMP - REMOVAL, DOME/CARGO.......8L-22
LAMP - REMOVAL, FRONT FOG..........8L-8
LAMP - REMOVAL, LICENSE............8L-17
LAMP - REMOVAL, LIFTGATE...........8L-22
LAMP - REMOVAL, PARK/TURN SIGNAL . . 8L-18
LAMP - REMOVAL, READING...........8L-23
LAMP - REMOVAL, TAIL...............8L-18
LAMP - REMOVAL, VANITY.............8L-24
LAMP REPLACEMENT - STANDARD
PROCEDURE, MODULE................8M-3
LAMP REPLACEMENT - STANDARD
PROCEDURE, READING/COURTESY
.......8M-3
LAMP SWITCH - DESCRIPTION, BRAKE
....8L-4
LAMP SWITCH - DIAGNOSIS AND
TESTING, BRAKE
......................8L-4
LAMP SWITCH - INSTALLATION,
BACK-UP
...........................21-62
LAMP SWITCH - INSTALLATION, BRAKE
. . . 8L-5LAMP SWITCH - INSTALLATION, CENTER
CONSOLE...........................8L-21
LAMP SWITCH - INSTALLATION, GLOVE
BOX ...............................8L-22
LAMP SWITCH - OPERATION, BRAKE......8L-4
LAMP SWITCH - REMOVAL, BACK-UP....21-62
LAMP SWITCH - REMOVAL, BRAKE.......8L-5
LAMP SWITCH - REMOVAL, CENTER
CONSOLE...........................8L-21
LAMP SWITCH - REMOVAL, GLOVE BOX . . 8L-22
LAMP UNIT - INSTALLATION, CENTER
HIGH MOUNTED STOP.................8L-6
LAMP UNIT - INSTALLATION, TAIL.......8L-19
LAMP UNIT - REMOVAL, CENTER HIGH
MOUNTED STOP......................8L-6
LAMP UNIT - REMOVAL, TAIL...........8L-19
LAMP UNIT ALIGNMENT - EXPORT -
STANDARD PROCEDURE, FRONT FOG.....8L-9
LAMP UNIT ALIGNMENT - STANDARD
PROCEDURE, FRONT FOG...............8L-9
LAMPS - INSTALLATION, CLUSTER
ILLUMINATION......................8L-21
LAMPS - REMOVAL, CLUSTER
ILLUMINATION......................8L-21
LAMPS, SPECIFICATIONS - EXTERIOR.....8L-3
LAMPS, SPECIFICATIONS - INTERIOR....8L-20
LAMPS/LIGHTING - EXTERIOR -
DESCRIPTION........................8L-2
LAMPS/LIGHTING - EXTERIOR -
OPERATION..........................8L-2
LAMPS/LIGHTING - EXTERIOR -
WARNING...........................8L-3
LASH ADJUSTER NOISE DIAGNOSIS -
DIAGNOSIS AND TESTING, HYDRAULIC....9-34
LASH ADJUSTERS - INSTALLATION,
HYDRAULIC..........................9-34
LASH ADJUSTERS - REMOVAL,
HYDRAULIC..........................9-34
LATCH - DESCRIPTION...........8N-13,8N-29
LATCH - INSTALLATION.....23-18,23-41,23-61
LATCH - INSTALLATION..........8N-14,8N-29
LATCH - INSTALLATION, FUEL FILL
DOOR BLOCKER.....................23-53
LATCH - INSTALLATION, GLOVE BOX.....23-64
LATCH - INSTALLATION, HOLD OPEN.....23-25
LATCH / LOCK ASSEMBLY -
INSTALLATION.......................23-27
LATCH / LOCK ASSEMBLY - REMOVAL....23-26
LATCH - OPERATION............8N-13,8N-29
LATCH - REMOVAL.........23-18,23-41,23-61
LATCH - REMOVAL..............8N-13,8N-29
LATCH - REMOVAL, FUEL FILL DOOR
BLOCKER...........................23-53
LATCH - REMOVAL, GLOVE BOX.........23-64
LATCH - REMOVAL, HOLD OPEN........23-25
LATCH ACTUATOR - DESCRIPTION......8N-14
LATCH ACTUATOR - INSTALLATION......8N-14
LATCH ACTUATOR - OPERATION........8N-14
LATCH ACTUATOR - REMOVAL..........8N-14
LATCH CABLE - INSTALLATION, HOLD
OPEN..............................23-38
LATCH CABLE - REMOVAL, HOLD OPEN . . . 23-38
LATCH HANDLE - INSTALLATION, INSIDE . . 23-34
LATCH HANDLE - REMOVAL, INSIDE.....23-34
LATCH LOCKING LINK - INSTALLATION,
SEAT RISER........................23-106
LATCH LOCKING LINK - REMOVAL, SEAT
RISER
............................23-106
LATCH RELEASE CABLE - INSTALLATION
. . 23-62
LATCH RELEASE CABLE - REMOVAL
.....23-61
LATCH STRIKER - INSTALLATION
. . 23-19,23-41,
23-62
LATCH STRIKER - INSTALLATION, FUEL
FILL DOOR BLOCKER
.................23-53
LATCH STRIKER - INSTALLATION, GLOVE
BOX
...............................23-64
LATCH STRIKER - INSTALLATION, HOLD
OPEN
..............................23-26
LATCH STRIKER - INSTALLATION, REAR
. . 23-29
LATCH STRIKER - REMOVAL
. 23-19,23-41,23-62
LATCH STRIKER - REMOVAL, FUEL FILL
DOOR BLOCKER
.....................23-53
LATCH STRIKER - REMOVAL, GLOVE
BOX
...............................23-64
LATCH STRIKER - REMOVAL, HOLD
OPEN
..............................23-26
LATCH STRIKER - REMOVAL, REAR
......23-29LEAD - DIAGNOSIS AND TESTING,
TIRE/VEHICLE..................22-14,22s-6
LEAF SPRING FRONT BUSHING -
INSTALLATION........................2-30
LEAF SPRING FRONT BUSHING -
REMOVAL...........................2-29
LEAK DETECTION ASSY - INSTALLATION,
NATURAL VAC.......................25-13
LEAK DETECTION ASSY - REMOVAL,
NATURAL VAC.......................25-13
LEAK DETECTION PUMP - INSTALLATION . 25-13
LEAK DETECTION PUMP - REMOVAL.....25-13
LEAK DIAGNOSIS, DIAGNOSIS AND
TESTING - FLUID......................21-3
LEAK INSPECTION - DIAGNOSIS AND
TESTING, ENGINE OIL...............9-8,9-82
LEAK REPAIRING - STANDARD
PROCEDURE, TIRE..............22-17,22s-9
LEAK TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM.....................7-2
LEAKAGE - DIAGNOSIS AND TESTING,
TORQUE CONVERTER HOUSING FLUID . . 21-123,
21s-31
LEAKAGE TEST - DIAGNOSIS AND
TESTING, CYLINDER COMBUSTION
PRESSURE.......................9-83,9-9
LEAKS - DIAGNOSIS AND TESTING,
INTAKE MANIFOLD...............9-145,9-58
LEAKS - DIAGNOSIS AND TESTING,
REFRIGERANT SYSTEM...............24-66
LEAKS - DIAGNOSIS AND TESTING,
WATER .............................23-1
LEARN CYCLE - STANDARD
PROCEDURE, POWER DOOR.............8N-28
LEARN CYCLE - STANDARD
PROCEDURE, POWER LIFTGATE..........8N-9
LEARN PROCEDURE - STANDARD
PROCEDURE, QUICK.............8E-16,8E-23
LEFT - CLEANING, EXHAUST MANIFOLD . . 9-152
LEFT - INSPECTION, EXHAUST
MANIFOLD..........................9-152
LEFT - INSTALLATION, CYLINDER HEAD
COVER.............................9-103
LEFT - INSTALLATION, EXHAUST
MANIFOLD..........................9-152
LEFT - REMOVAL, CYLINDER HEAD
COVER.............................9-103
LEFT - REMOVAL, EXHAUST MANIFOLD . . . 9-152
LEFT B-PILLAR SWITCH - DESCRIPTION . . 8N-32
LEFT B-PILLAR SWITCH - INSTALLATION . 8N-32
LEFT B-PILLAR SWITCH - OPERATION....8N-32
LEFT B-PILLAR SWITCH - REMOVAL.....8N-32
LEFT D-PILLAR TRIM PANEL -
INSTALLATION.......................23-78
LEFT D-PILLAR TRIM PANEL - REMOVAL . 23-78
LEFT MOUNT - INSTALLATION......9-133,9-50
LEFT MOUNT - REMOVAL..........9-133,9-49
LEFT OUTBOARD - INSTALLATION, SEAT
BELT & RETRACTOR - SECOND ROW....8O-17
LEFT OUTBOARD - REMOVAL, SEAT
BELT & RETRACTOR - SECOND ROW....8O-17
LEFT QUARTER TRIM PANEL -
INSTALLATION.......................23-80
LEFT QUARTER TRIM PANEL - REMOVAL
. 23-80
LENS - INSTALLATION, CLUSTER
........8J-10
LENS - REMOVAL, CLUSTER
............8J-10
LEVEL - STANDARD PROCEDURE,
CHECKING BATTERY ELECTROLYTE
......8F-14
LEVEL - STANDARD PROCEDURE,
REFRIGERANT OIL
...................24-93
LEVEL AND CONDITION CHECK,
STANDARD PROCEDURE - FLUID
......21-201,
21s-102
LEVEL CHECK - STANDARD
PROCEDURE, COOLANT
.................7-5
LEVEL CHECK - STANDARD
PROCEDURE, ENGINE OIL
..............9-137
LEVEL CHECK - STANDARD
PROCEDURE, FLUID
..................21-71
LEVEL CHECK, STANDARD PROCEDURE
- ENGINE OIL
........................9-53
LEVEL CHECKING - STANDARD
PROCEDURE, BRAKE FLUID
........5-32,5s-31
LEVEL CHECKING - STANDARD
PROCEDURE, POWER STEERING FLUID
. . . 19-44
LEVEL INSPECTION - STANDARD
PROCEDURE, FLUID
...................21-4
RSINDEX19
Description Group-Page Description Group-Page Description Group-Page
Page 2565 of 2585
MODULE - DESCRIPTION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - DESCRIPTION, POWER
LIFTGATE CONTROL..................8E-10
MODULE - DESCRIPTION, REAR
DRIVELINE...........................3-23
MODULE - DESCRIPTION, REMOTE
KEYLESS ENTRY.....................8N-43
MODULE - DESCRIPTION, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - DESCRIPTION, SENTRY KEY
REMOTE ENTRY......................8Q-3
MODULE - DESCRIPTION, SLIDING
DOOR CONTROL.....................8E-19
MODULE - DESCRIPTION,
TRANSMISSION CONTROL.............8E-20
MODULE - DIAGNOSIS AND TESTING,
FRONT CONTROL.....................8E-7
MODULE - DIAGNOSIS AND TESTING,
HEATED SEAT ........................8E-9
MODULE - DIAGNOSIS AND TESTING,
MEMORY SEAT/MIRROR...............8E-10
MODULE - DIAGNOSIS AND TESTING,
REMOTE KEYLESS ENTRY.............8N-43
MODULE - DIAGNOSIS AND TESTING,
SENTRY KEY REMOTE ENTRY...........8Q-5
MODULE - EXPORT - DESCRIPTION,
ANTENNA...........................8A-6
MODULE - EXPORT - DIAGNOSIS AND
TESTING, ANTENNA...................8A-7
MODULE - EXPORT - INSTALLATION,
ANTENNA...........................8A-7
MODULE - EXPORT - OPERATION,
ANTENNA.............................8A-6
MODULE - EXPORT - REMOVAL,
ANTENNA...........................8A-7
MODULE - INSTALLATION, BODY
CONTROL............................8s-3
MODULE - INSTALLATION, BODY
CONTROL...........................8E-5
MODULE - INSTALLATION, FRONT
CONTROL...........................8E-8
MODULE - INSTALLATION, FUEL PUMP....14-9
MODULE - INSTALLATION, HEATED SEAT . . 8E-10
MODULE - INSTALLATION, INTEGRATED
POWER..........................8W-97-3
MODULE - INSTALLATION, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - INSTALLATION, POWER
LIFTGATE CONTROL..................8E-11
MODULE - INSTALLATION, REMOTE
KEYLESS ENTRY.....................8N-44
MODULE - INSTALLATION, SENTRY KEY
IMMOBILIZER.......................8E-19
MODULE - INSTALLATION, SENTRY KEY
REMOTE ENTRY......................8Q-6
MODULE - INSTALLATION, SLIDING
DOOR CONTROL.....................8E-20
MODULE - INSTALLATION, WIPER.......8R-15
MODULE - OPERATION, BODY CONTROL . . . 8s-1
MODULE - OPERATION, BODY CONTROL . . . 8E-3
MODULE - OPERATION, FRONT
CONTROL...........................8E-7
MODULE - OPERATION, FUEL PUMP
......14-8
MODULE - OPERATION, HEATED SEAT
.....8E-9
MODULE - OPERATION, INTEGRATED
POWER
..........................8W-97-2
MODULE - OPERATION, MEMORY
SEAT/MIRROR
.......................8E-10
MODULE - OPERATION, POWER
LIFTGATE CONTROL
..................8E-11
MODULE - OPERATION, REAR
DRIVELINE
...........................3-23
MODULE - OPERATION, REMOTE
KEYLESS ENTRY
.....................8N-43
MODULE - OPERATION, SENTRY KEY
IMMOBILIZER
.......................8E-18
MODULE - OPERATION, SENTRY KEY
REMOTE ENTRY
......................8Q-4
MODULE - OPERATION, SLIDING DOOR
CONTROL
..........................8E-19
MODULE - OPERATION, TRANSMISSION
CONTROL
..........................8E-20
MODULE - REAR BLOWER MOTOR -
DESCRIPTION, POWER
................24-41
MODULE - REAR BLOWER MOTOR -
INSTALLATION, POWER
...............24-42MODULE - REAR BLOWER MOTOR -
OPERATION, POWER..................24-41
MODULE - REAR BLOWER MOTOR -
REMOVAL, POWER...................24-41
MODULE - REMOVAL, BODY CONTROL....8s-3
MODULE - REMOVAL, BODY CONTROL....8E-4
MODULE - REMOVAL, FRONT CONTROL . . . 8E-8
MODULE - REMOVAL, FUEL PUMP........14-8
MODULE - REMOVAL, HEATED SEAT......8E-9
MODULE - REMOVAL, INTEGRATED
POWER..........................8W-97-2
MODULE - REMOVAL, MEMORY
SEAT/MIRROR.......................8E-10
MODULE - REMOVAL, POWER LIFTGATE
CONTROL..........................8E-11
MODULE - REMOVAL, REMOTE KEYLESS
ENTRY.............................8N-44
MODULE - REMOVAL, SENTRY KEY
IMMOBILIZER.......................8E-18
MODULE - REMOVAL, SENTRY KEY
REMOTE ENTRY......................8Q-5
MODULE - REMOVAL, SLIDING DOOR
CONTROL..........................8E-19
MODULE - REMOVAL, WIPER...........8R-15
MODULE - SPECIFICATIONS, REAR
DRIVELINE...........................3-34
MODULE, BENCH SEAT - REMOVAL,
CHILD SEAT.........................23-87
MODULE FLUIDS - DESCRIPTION, AWD
REAR DRIVELINE......................0-6
MODULE LAMP REPLACEMENT -
STANDARD PROCEDURE.................8M-3
MODULE NOISE - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-24
MODULE OPERATION - DIAGNOSIS AND
TESTING, REAR DRIVELINE.............3-26
MOLDING - INSTALLATION, FRONT
DOOR INNER BELT..................23-115
MOLDING - INSTALLATION, FRONT
DOOR OUTER BELT..................23-113
MOLDING - INSTALLATION, ROOF JOINT . . 23-58
MOLDING - REMOVAL, FRONT DOOR
INNER BELT........................23-115
MOLDING - REMOVAL, FRONT DOOR
OUTER BELT.......................23-113
MOLDING - REMOVAL, ROOF JOINT......23-58
MOLDINGS - INSTALLATION, BODY SIDE . . 23-46
MOLDINGS - REMOVAL, BODY SIDE.....23-45
MONITORED COMPONENT -
DESCRIPTION........................25-1
MONITORED SYSTEMS - DESCRIPTION....25-6
MONITORING - DESCRIPTION, TIRE
PRESSURE.....................22-9,22s-1
MONITORING - OPERATION, TIRE
PRESSURE.....................22-9,22s-1
MOTOR - DESCRIPTION, BLOWER . . 24-46,24-57
MOTOR - DESCRIPTION, IDLE AIR
CONTROL..........................14-28
MOTOR - DESCRIPTION, LIFTGATE......8N-15
MOTOR - DESCRIPTION, POWER
MODULE - BLOWER..................24-31
MOTOR - DESCRIPTION, POWER
MODULE - REAR BLOWER.............24-41
MOTOR - DESCRIPTION, SLIDING DOOR . . 8N-30
MOTOR - DIAGNOSIS AND TESTING,
BLOWER...........................24-47
MOTOR - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
MOTOR - DIAGNOSIS AND TESTING,
RADIATOR FAN.......................7-29
MOTOR - DIAGNOSIS AND TESTING,
REAR BLOWER......................24-58
MOTOR - DIAGNOSIS AND TESTING,
VENT WINDOW......................8N-63
MOTOR - INSTALLATION, BLOWER . 24-49,24-58
MOTOR - INSTALLATION, FRONT
WASHER PUMP......................8R-8
MOTOR - INSTALLATION, FRONT WIPER . . . 8R-9
MOTOR - INSTALLATION, IDLE AIR
CONTROL..........................14-29
MOTOR - INSTALLATION, LIFTGATE
......8N-15
MOTOR - INSTALLATION, POWER
MODULE - BLOWER
..................24-32
MOTOR - INSTALLATION, POWER
MODULE - REAR BLOWER
.............24-42
MOTOR - INSTALLATION, REAR WASHER
PUMP
.............................8R-10
MOTOR - INSTALLATION, REAR WIPER
. . . 8R-11MOTOR - INSTALLATION, SLIDING DOOR . 8N-31
MOTOR - INSTALLATION, SLIDING DOOR
LOCK.........................8N-44,8N-6
MOTOR - INSTALLATION, SUNROOF.....23-121
MOTOR - INSTALLATION, VENT WINDOW . 8N-64
MOTOR - OPERATION, BLOWER....24-46,24-57
MOTOR - OPERATION, IDLE AIR
CONTROL..........................14-28
MOTOR - OPERATION, LIFTGATE........8N-15
MOTOR - OPERATION, POWER MODULE
- BLOWER..........................24-31
MOTOR - OPERATION, POWER MODULE
- REAR BLOWER.....................24-41
MOTOR - OPERATION, SLIDING DOOR . . . 8N-30
MOTOR - REMOVAL, BLOWER.....24-47,24-58
MOTOR - REMOVAL, FRONT WASHER
PUMP..............................8R-8
MOTOR - REMOVAL, FRONT WIPER......8R-9
MOTOR - REMOVAL, IDLE AIR CONTROL . . 14-29
MOTOR - REMOVAL, LIFTGATE.........8N-15
MOTOR - REMOVAL, POWER MODULE -
BLOWER...........................24-31
MOTOR - REMOVAL, POWER MODULE -
REAR BLOWER......................24-41
MOTOR - REMOVAL, REAR WASHER
PUMP.............................8R-10
MOTOR - REMOVAL, REAR WIPER......8R-11
MOTOR - REMOVAL, SLIDING DOOR.....8N-30
MOTOR - REMOVAL, SLIDING DOOR
LOCK...........................8N-44,8N-6
MOTOR - REMOVAL, SUNROOF........23-121
MOTOR - REMOVAL, VENT WINDOW.....8N-63
MOTOR - REMOVAL, WINDOW..........8N-64
MOTOR RELAY - DESCRIPTION,
BLOWER......................24-24,24-37
MOTOR RELAY - INSTALLATION,
BLOWER......................24-25,24-38
MOTOR RELAY - OPERATION, BLOWER . . 24-24,
24-37
MOTOR RELAY - REMOVAL, BLOWER....24-25,
24-38
MOTOR RESISTOR - DESCRIPTION,
BLOWER...........................24-38
MOTOR RESISTOR - INSTALLATION,
BLOWER...........................24-39
MOTOR RESISTOR - OPERATION,
BLOWER...........................24-38
MOTOR RESISTOR - REMOVAL,
BLOWER...........................24-39
MOTOR RESISTOR BLOCK -
DESCRIPTION, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, BLOWER...............24-26
MOTOR RESISTOR BLOCK - DIAGNOSIS
AND TESTING, REAR BLOWER..........24-38
MOTOR RESISTOR BLOCK -
INSTALLATION, BLOWER..............24-27
MOTOR RESISTOR BLOCK - OPERATION,
BLOWER...........................24-26
MOTOR RESISTOR BLOCK - REMOVAL,
BLOWER...........................24-26
MOUNT - INSTALLATION, FRONT....9-131,9-49
MOUNT - INSTALLATION, LEFT......9-133,9-50
MOUNT - INSTALLATION, REAR.....9-134,9-50
MOUNT - INSTALLATION, RIGHT....9-135,9-51
MOUNT - REMOVAL, FRONT........9-131,9-49
MOUNT - REMOVAL, LEFT.........9-133,9-49
MOUNT - REMOVAL, REAR.........9-133,9-50
MOUNT - REMOVAL, RIGHT........9-135,9-51
MOUNT BUSHINGS - INSTALLATION,
FRONT CROSSMEMBER...............13-12
MOUNT BUSHINGS - REMOVAL, FRONT
CROSSMEMBER.....................13-12
MOUNTED STOP LAMP - INSTALLATION,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP - REMOVAL,
CENTER HIGH........................8L-6
MOUNTED STOP LAMP UNIT -
INSTALLATION, CENTER HIGH...........8L-6
MOUNTED STOP LAMP UNIT -
REMOVAL, CENTER HIGH
...............8L-6
MOUNTING - DESCRIPTION, ENGINE
. 9-131,9-48
MOUNTING - STANDARD PROCEDURE,
TIRE AND WHEEL MATCH
...............22-7
MOUNTING BRACKET - 2.4L ENGINE -
INSTALLATION, A/C COMPRESSOR
.......24-76
MOUNTING BRACKET - 2.4L ENGINE -
REMOVAL, A/C COMPRESSOR
..........24-75
22 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
Page 2571 of 2585
RECOVERY CONTAINER - DESCRIPTION,
COOLANT............................7-19
RECOVERY CONTAINER - INSTALLATION,
COOLANT............................7-20
RECOVERY CONTAINER - OPERATION,
COOLANT............................7-19
RECOVERY CONTAINER - REMOVAL,
COOLANT............................7-20
RECOVERY SYSTEM - DIAGNOSIS AND
TESTING, COOLANT...................7-20
REFACING VALVES AND VALVE SEATS -
STANDARD PROCEDURE..........9-104,9s-21
REFERENCES - DESCRIPTION, TORQUE . . Intro.-8
REFRIGERANT - DESCRIPTION..........24-92
REFRIGERANT - OPERATION............24-92
REFRIGERANT LINE - DESCRIPTION......24-65
REFRIGERANT LINES - INSTALLATION,
UNDERBODY.......................24-111
REFRIGERANT LINES - OPERATION......24-65
REFRIGERANT LINES - REMOVAL,
UNDERBODY.......................24-110
REFRIGERANT OIL - DESCRIPTION......24-92
REFRIGERANT OIL - OPERATION........24-92
REFRIGERANT OIL LEVEL - STANDARD
PROCEDURE........................24-93
REFRIGERANT RECOVERY - STANDARD
PROCEDURE........................24-71
REFRIGERANT SYSTEM CHARGE -
STANDARD PROCEDURE...............24-72
REFRIGERANT SYSTEM EVACUATE -
STANDARD PROCEDURE...............24-72
REFRIGERANT SYSTEM LEAKS -
DIAGNOSIS AND TESTING.............24-66
REFRIGERANT SYSTEM SERVICE
EQUIPMENT - STANDARD PROCEDURE . . . 24-70
REGULATOR - DESCRIPTION, VOLTAGE . . . 8F-27,
8F-29
REGULATOR - INSTALLATION, FUEL
PRESSURE..........................14-7
REGULATOR - MANUAL - INSTALLATION,
WINDOW...........................23-23
REGULATOR - MANUAL - REMOVAL,
WINDOW...........................23-22
REGULATOR - OPERATION, FUEL
PRESSURE..........................14-7
REGULATOR - OPERATION, VOLTAGE....8F-27,
8F-29
REGULATOR - POWER - INSTALLATION,
WINDOW...........................23-22
REGULATOR - POWER - REMOVAL,
WINDOW...........................23-22
REGULATOR - REMOVAL, FUEL
PRESSURE..........................14-7
REINFORCEMENT - INSTALLATION,
FRONT BUMPER......................13-2
REINFORCEMENT - INSTALLATION,
GRILLE OPENING....................23-54
REINFORCEMENT - INSTALLATION, REAR
BUMPER............................13-3
REINFORCEMENT - REMOVAL, FRONT
BUMPER............................13-2
REINFORCEMENT - REMOVAL, GRILLE
OPENING...........................23-54
REINFORCEMENT - REMOVAL, REAR
BUMPER............................13-3
RELAY - DESCRIPTION, A/C
COMPRESSOR CLUTCH
...............24-19
RELAY - DESCRIPTION, AUTO SHUT
DOWN
..............................8I-3
RELAY - DESCRIPTION, BLOWER
MOTOR
.......................24-24,24-37
RELAY - DESCRIPTION, FUEL PUMP
.....14-28
RELAY - DESCRIPTION, RADIATOR FAN
....7-30
RELAY - DESCRIPTION, REAR WINDOW
DEFOGGER
..........................8G-3
RELAY - DESCRIPTION, TRANSMISSION
CONTROL
...................21-247,21s-150
RELAY - INSTALLATION, A/C
COMPRESSOR CLUTCH
...............24-20
RELAY - INSTALLATION, BLOWER
MOTOR
.......................24-25,24-38
RELAY - INSTALLATION, RADIATOR FAN
. . . 7-30
RELAY - INSTALLATION, REAR WINDOW
DEFOGGER
..........................8G-3
RELAY - OPERATION, A/C COMPRESSOR
CLUTCH
............................24-19
RELAY - OPERATION, AUTO SHUT DOWN
. . . 8I-3RELAY - OPERATION, BLOWER MOTOR . . 24-24,
24-37
RELAY - OPERATION, FUEL PUMP.......14-28
RELAY - OPERATION, RADIATOR FAN......7-30
RELAY - OPERATION, REAR WINDOW
DEFOGGER..........................8G-3
RELAY - OPERATION, TRANSMISSION
CONTROL...................21-248,21s-150
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-20
RELAY - REMOVAL, BLOWER MOTOR....24-25,
24-38
RELAY - REMOVAL, RADIATOR FAN.......7-30
RELAY - REMOVAL, REAR WINDOW
DEFOGGER..........................8G-3
RELEASE - STANDARD PROCEDURE,
PARKING BRAKE AUTOMATIC
ADJUSTER TENSION..............5-58,5s-61
RELEASE CABLE - INSTALLATION, LATCH . 23-62
RELEASE CABLE - REMOVAL, LATCH.....23-61
RELEASE LEVER AND BEARING -
INSTALLATION, CLUTCH.................6-7
RELEASE LEVER AND BEARING -
REMOVAL, CLUTCH.....................6-6
RELEASE PROCEDURE - STANDARD
PROCEDURE, FUEL SYSTEM
PRESSURE..........................14-2
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-73
RELIEF VALVE - INSTALLATION, OIL
PRESSURE.........................9-141
RELIEF VALVE - OPERATION, HIGH
PRESSURE...........................24-73
RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-141
REMOTE ENTRY MODULE -
DESCRIPTION, SENTRY KEY.............8Q-3
REMOTE ENTRY MODULE - DIAGNOSIS
AND TESTING, SENTRY KEY.............8Q-5
REMOTE ENTRY MODULE -
INSTALLATION, SENTRY KEY............8Q-6
REMOTE ENTRY MODULE - OPERATION,
SENTRY KEY.........................8Q-4
REMOTE ENTRY MODULE - REMOVAL,
SENTRY KEY.........................8Q-5
REMOTE ENTRY SYSTEM - DIAGNOSIS
AND TESTING, SENTRY KEY.............8Q-3
REMOTE KEYLESS ENTRY MODULE -
DESCRIPTION.......................8N-43
REMOTE KEYLESS ENTRY MODULE -
DIAGNOSIS AND TESTING.............8N-43
REMOTE KEYLESS ENTRY MODULE -
INSTALLATION......................8N-44
REMOTE KEYLESS ENTRY MODULE -
OPERATION.........................8N-43
REMOTE KEYLESS ENTRY MODULE -
REMOVAL..........................8N-44
REMOTE KEYLESS ENTRY
TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-5
REMOTE SWITCH - DIAGNOSIS AND
TESTING...........................8N-49
REMOTE SWITCH - INSTALLATION......8N-49
REMOTE SWITCH - REMOVAL..........8N-49
REMOTE SWITCHES - DESCRIPTION.....8A-12
REMOTE SWITCHES - DIAGNOSIS AND
TESTING...........................8A-12
REMOTE SWITCHES - INSTALLATION.....8A-14
REMOTE SWITCHES - OPERATION.......8A-12
REMOTE SWITCHES - REMOVAL........8A-13
REPAIR - DESCRIPTION, FRONT CRADLE
CROSSMEMBER THREAD...............13-9
REPAIR - DESCRIPTION, THREADED
HOLE.............................Intro.-5
REPAIR - STANDARD PROCEDURE, GRID
LINE AND TERMINAL..................8G-4
REPAIR - STANDARD PROCEDURE,
INTAKE MANIFOLD VACUUM PORT......9-145
REPAIR - STANDARD PROCEDURE,
MANIFOLD STRIPPED THREAD
..........9-145
REPAIR - STANDARD PROCEDURE,
PLASTIC BODY PANEL
.................23-3
REPAIR OF DAMAGED OR WORN
THREADS - STANDARD PROCEDURE
. . 9-10,9-86
REPAIRING - STANDARD PROCEDURE,
TIRE LEAK
.....................22-17,22s-9
REQUIREMENTS - DESCRIPTION,
ENGINE COOLING SYSTEM
..............24-1REQUIREMENTS - DESCRIPTION, FUEL.....0-4
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-6
RESERVOIR - DESCRIPTION, VACUUM....8P-6
RESERVOIR - INSTALLATION, VACUUM....8P-6
RESERVOIR - INSTALLATION, WASHER . . . 8R-13
RESERVOIR - OPERATION, VACUUM......8P-6
RESERVOIR - REMOVAL, VACUUM........8P-6
RESERVOIR - REMOVAL, WASHER......8R-13
RESET - STANDARD PROCEDURE,
PARKING BRAKE AUTOMATIC
ADJUSTER TENSION..............5-59,5s-61
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-2
RESISTANCE TEST - DIAGNOSIS AND
TESTING, FEED CIRCUIT..........8F-32,8F-34
RESISTOR - DESCRIPTION, BLOWER
MOTOR............................24-38
RESISTOR - INSTALLATION, BLOWER
MOTOR............................24-39
RESISTOR - OPERATION, BLOWER
MOTOR............................24-38
RESISTOR - REMOVAL, BLOWER
MOTOR............................24-39
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-26
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR............24-26
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, REAR BLOWER MOTOR.......24-38
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR......................24-27
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR....................24-26
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR............................24-26
RESONATOR - INSTALLATION............11-9
RESONATOR - REMOVAL...............11-9
RESTRAINT ANCHOR - DESCRIPTION,
CHILD..............................8O-4
RESTRAINT ANCHOR - OPERATION,
CHILD..............................8O-4
RESTRAINT CONTROLLER -
DESCRIPTION, OCCUPANT..............8O-8
RESTRAINT CONTROLLER -
INSTALLATION, OCCUPANT.............8O-8
RESTRAINT CONTROLLER - OPERATION,
OCCUPANT..........................8O-8
RESTRAINT CONTROLLER - REMOVAL,
OCCUPANT..........................8O-8
RESTRAINTS - DESCRIPTION............8O-2
RESTRAINTS - OPERATION.............8O-2
RESTRAINTS - WARNING...............8O-2
RESTRICTION CHECK - DIAGNOSIS AND
TESTING, EXHAUST SYSTEM............11-2
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL..........9-129
RETAINER - INSTALLATION, PLASTIC
GROCERY BAG
.....................23-105
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL
......................9-129
RETAINER - REMOVAL, PLASTIC
GROCERY BAG
.....................23-104
RETRACTOR - FIRST ROW - OUTBOARD
- INSTALLATION, SEAT BELT
...........8O-14
RETRACTOR - FIRST ROW - OUTBOARD
- REMOVAL, SEAT BELT
...............8O-14
RETRACTOR - OUTBOARD - FRONT -
INSTALLATION, SEAT BELT
.............8O-14
RETRACTOR - OUTBOARD - FRONT -
REMOVAL, SEAT BELT
................8O-14
RETRACTOR - SECOND ROW - LEFT
OUTBOARD - INSTALLATION, SEAT
BELT
..............................8O-17
RETRACTOR - SECOND ROW - LEFT
OUTBOARD - REMOVAL, SEAT BELT
.....8O-17
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - INSTALLATION, SEAT
BELT
..............................8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD - REMOVAL, SEAT BELT
.....8O-15
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
INSTALLATION, SEAT BELT
.............8O-16
RETRACTOR - SECOND ROW - RIGHT
OUTBOARD WITH REAR HVAC - LWB -
REMOVAL, SEAT BELT
................8O-16
28 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
Page 2577 of 2585
STRIKER - REMOVAL, LATCH . 23-19,23-41,23-62
STRIKER - REMOVAL, REAR LATCH......23-29
STRIPPED THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD..............9-145
STRUCTURAL ADHESIVE LOCATIONS -
SPECIFICATIONS....................23-156
STRUCTURAL COLLAR - INSTALLATION....9-48
STRUCTURAL COLLAR - REMOVAL.......9-47
STRUT ASSEMBLY - ASSEMBLY..........2-23
STRUT ASSEMBLY - DESCRIPTION.......2-19
STRUT ASSEMBLY - DIAGNOSIS AND
TESTING............................2-20
STRUT ASSEMBLY - DISASSEMBLY.......2-21
STRUT ASSEMBLY - INSTALLATION.......2-25
STRUT ASSEMBLY - OPERATION.........2-20
STRUT ASSEMBLY - REMOVAL...........2-21
STUDS - FRONT - INSTALLATION,
WHEEL MOUNTING...................22-21
STUDS - FRONT - REMOVAL, WHEEL
MOUNTING.........................22-20
STUDS - REAR - INSTALLATION, WHEEL
MOUNTING.........................22-22
STUDS - REAR - REMOVAL, WHEEL
MOUNTING.........................22-21
SUCTION LINE - INSTALLATION . . . 24-107,24-95
SUCTION LINE - REMOVAL.......24-106,24-94
SUN VISOR - INSTALLATION...........23-82
SUN VISOR - REMOVAL...............23-82
SUN VISOR SUPPORT - INSTALLATION.....23-83
SUN VISOR SUPPORT - REMOVAL.......23-83
SUNROOF - DESCRIPTION............23-116
SUNROOF - DIAGNOSIS AND TESTING . . . 23-116
SUNROOF ASSEMBLY - INSTALLATION . . 23-120
SUNROOF ASSEMBLY - REMOVAL......23-120
SUNROOF GLASS PANEL ADJUSTMENT,
ADJUSTMENTS.....................23-120
SUNROOF MOTOR - INSTALLATION.....23-121
SUNROOF MOTOR - REMOVAL.........23-121
SUNROOF SWITCH - INSTALLATION.....23-123
SUNROOF SWITCH - REMOVAL........23-123
SUNSHADE - INSTALLATION...........23-121
SUNSHADE - REMOVAL..............23-120
SUPPLEMENTAL CABIN HEATER -
DIAGNOSIS AND TESTING, DIESEL......24-113
SUPPLEMENTAL DIESEL HEATER
WIRING - INSTALLATION.............24-119
SUPPLEMENTAL DIESEL HEATER
WIRING - REMOVAL.................24-119
SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT ..............................8E-15
SUPPLY - PCM OUTPUT - SBEC
CONTROLLER - OPERATION, 8-VOLT.....8E-15
SUPPORT - INSTALLATION, LUMBAR....23-106
SUPPORT - INSTALLATION, SUN VISOR . . . 23-83
SUPPORT - REMOVAL, LUMBAR.......23-106
SUPPORT - REMOVAL, SUN VISOR......23-83
SUPPORT CYLINDER - INSTALLATION....23-43
SUPPORT CYLINDER - REMOVAL........23-43
SUPPORT PLATE - DRUM BRAKE -
INSTALLATION...................5-56,5s-58
SUPPORT PLATE - DRUM BRAKE -
REMOVAL......................5-56,5s-58
SUPPRESSION COMPONENTS -
DESCRIPTION, RADIO NOISE...........8A-11
SUPPRESSION COMPONENTS -
OPERATION, RADIO NOISE.............8A-12
SURFACE PREPARATION - STANDARD
PROCEDURE, ENGINE GASKET.......9-11,9-85
SUSPENSION - DESCRIPTION, FRONT......2-2
SUSPENSION - DESCRIPTION, REAR
......2-27
SUSPENSION - OPERATION, FRONT
........2-2
SUSPENSION - OPERATION, REAR
........2-28
SUSPENSION AND STEERING -
DIAGNOSIS AND TESTING
..............2-50
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - FRONT
................2-3
SUSPENSION FASTENER TORQUE,
SPECIFICATIONS - REAR
................2-28
SUSPENSION, SPECIAL TOOLS - FRONT
....2-3
SUSPENSION, SPECIAL TOOLS - REAR
....2-28
SWITCH - DESCRIPTION
................8P-6
SWITCH - DESCRIPTION, AUTOSTICK
. . . 21-189
SWITCH - DESCRIPTION, BRAKE FLUID
LEVEL
..........................5-10,5s-9
SWITCH - DESCRIPTION, BRAKE LAMP
....8L-4
SWITCH - DESCRIPTION, DOOR
CYLINDER LOCK
.....................8N-40SWITCH - DESCRIPTION, DRIVER
HEATED SEAT ........................8G-8
SWITCH - DESCRIPTION, DRIVER SEAT . . 8N-10,
8N-53
SWITCH - DESCRIPTION, EXTERIOR
HANDLE...........................8N-11
SWITCH - DESCRIPTION, FULL OPEN....8N-12,
8N-31
SWITCH - DESCRIPTION, HORN..........8H-5
SWITCH - DESCRIPTION, LEFT B-PILLAR . 8N-32
SWITCH - DESCRIPTION, MEMORY SET . . 8N-12,
8N-55
SWITCH - DESCRIPTION, OIL PRESSURE . 9-141
SWITCH - DESCRIPTION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - DESCRIPTION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - DESCRIPTION, REAR
WINDOW DEFOGGER..................8G-4
SWITCH - DESCRIPTION, REAR
WIPER/WASHER.....................8R-11
SWITCH - DESCRIPTION, RIGHT
B-PILLAR..........................8N-32
SWITCH - DIAGNOSIS AND TESTING,
BRAKE LAMP........................8L-4
SWITCH - DIAGNOSIS AND TESTING,
DOOR CYLINDER LOCK...............8N-40
SWITCH - DIAGNOSIS AND TESTING,
DOOR LOCK....................8N-4,8N-41
SWITCH - DIAGNOSIS AND TESTING,
DRIVER HEATED SEAT.................8G-9
SWITCH - DIAGNOSIS AND TESTING,
DRIVER SEAT...................8N-11,8N-54
SWITCH - DIAGNOSIS AND TESTING,
FAILED PARK........................8R-2
SWITCH - DIAGNOSIS AND TESTING,
FRONT WIPER/WASHER................8R-2
SWITCH - DIAGNOSIS AND TESTING,
HEADLAMP.........................8L-12
SWITCH - DIAGNOSIS AND TESTING,
MEMORY.....................8N-13,8N-56
SWITCH - DIAGNOSIS AND TESTING,
MULTI-FUNCTION....................8L-18
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER HEATED SEAT.............8G-13
SWITCH - DIAGNOSIS AND TESTING,
PASSENGER SEAT..............8N-14,8N-57
SWITCH - DIAGNOSIS AND TESTING,
REMOTE...........................8N-49
SWITCH - DIAGNOSIS AND TESTING,
TRACTION CONTROL...................5-82
SWITCH - DIAGNOSIS AND TESTING,
WINDOW...........................8N-64
SWITCH - EXPORT - DESCRIPTION,
DOOR CYLINDER LOCK................8N-3
SWITCH - EXPORT - DESCRIPTION,
POWER FOLDAWAY MIRROR...........8N-48
SWITCH - EXPORT - DIAGNOSIS AND
TESTING, DOOR CYLINDER LOCK........8N-3
SWITCH - EXPORT - INSTALLATION,
DOOR CYLINDER LOCK................8N-4
SWITCH - EXPORT - INSTALLATION,
HOOD AJAR.........................8Q-3
SWITCH - EXPORT - INSTALLATION,
POWER FOLDAWAY MIRROR
...........8N-49
SWITCH - EXPORT - OPERATION, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - OPERATION,
POWER FOLDAWAY MIRROR
...........8N-48
SWITCH - EXPORT - REMOVAL, DOOR
CYLINDER LOCK
......................8N-3
SWITCH - EXPORT - REMOVAL, HOOD
AJAR
...............................8Q-3
SWITCH - EXPORT - REMOVAL, POWER
FOLDAWAY MIRROR
..................8N-48
SWITCH - INSTALLATION
...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE
PEDALS
............................5s-10
SWITCH - INSTALLATION, BACK-UP
LAMP
..............................21-62
SWITCH - INSTALLATION, BRAKE FLUID
LEVEL
.........................5-11,5s-10
SWITCH - INSTALLATION, BRAKE LAMP
. . . 8L-5
SWITCH - INSTALLATION, CENTER
CONSOLE LAMP
.....................8L-21
SWITCH - INSTALLATION, CLUTCH
PEDAL INTERLOCK
....................6-14SWITCH - INSTALLATION, CLUTCH
PEDAL UPSTOP.......................6-16
SWITCH - INSTALLATION, DOOR
CYLINDER LOCK.....................8N-41
SWITCH - INSTALLATION, DOOR LOCK....8N-4,
8N-42
SWITCH - INSTALLATION, DRIVER
HEATED SEAT .......................8G-10
SWITCH - INSTALLATION, DRIVER SEAT . . 8N-12,
8N-55
SWITCH - INSTALLATION, EXTERIOR
HANDLE...........................8N-12
SWITCH - INSTALLATION, FULL OPEN....8N-13
SWITCH - INSTALLATION, GLOVE BOX
LAMP..............................8L-22
SWITCH - INSTALLATION, HEADLAMP....8L-13
SWITCH - INSTALLATION, IGNITION......19-16
SWITCH - INSTALLATION, LEFT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, MEMORY SET . 8N-13,
8N-56
SWITCH - INSTALLATION, MULTI-
FUNCTION..........................8L-18
SWITCH - INSTALLATION, OIL
PRESSURE.....................9-141,9-54
SWITCH - INSTALLATION, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - INSTALLATION, PASSENGER
SEAT.........................8N-15,8N-57
SWITCH - INSTALLATION, REMOTE......8N-49
SWITCH - INSTALLATION, RIGHT
B-PILLAR..........................8N-32
SWITCH - INSTALLATION, SUNROOF....23-123
SWITCH - INSTALLATION, WASHER
FLUID LEVEL........................8R-12
SWITCH - INSTALLATION, WINDOW.....8N-65
SWITCH - OPERATION.................8P-6
SWITCH - OPERATION, AUTOSTICK.....21-189
SWITCH - OPERATION, BRAKE FLUID
LEVEL..........................5-10,5s-9
SWITCH - OPERATION, BRAKE LAMP......8L-4
SWITCH - OPERATION, DOOR CYLINDER
LOCK..............................8N-40
SWITCH - OPERATION, DRIVER HEATED
SEAT ...............................8G-8
SWITCH - OPERATION, DRIVER SEAT....8N-11,
8N-54
SWITCH - OPERATION, EXTERIOR
HANDLE...........................8N-11
SWITCH - OPERATION, FULL OPEN . 8N-12,8N-31
SWITCH - OPERATION, LEFT B-PILLAR . . . 8N-32
SWITCH - OPERATION, MEMORY SET . . . 8N-13,
8N-56
SWITCH - OPERATION, OIL PRESSURE . . . 9-141
SWITCH - OPERATION, PASSENGER
HEATED SEAT .......................8G-12
SWITCH - OPERATION, PASSENGER
SEAT.........................8N-13,8N-56
SWITCH - OPERATION, REAR WINDOW
DEFOGGER..........................8G-4
SWITCH - OPERATION, REAR WIPER/
WASHER...........................8R-11
SWITCH - OPERATION, RIGHT B-PILLAR . . 8N-32
SWITCH - REMOVAL...................8P-6
SWITCH - REMOVAL, ADJUSTABLE
PEDALS............................5s-10
SWITCH - REMOVAL, BACK-UP LAMP....21-62
SWITCH - REMOVAL, BRAKE FLUID
LEVEL.........................5-11,5s-10
SWITCH - REMOVAL, BRAKE LAMP.......8L-5
SWITCH - REMOVAL, CENTER CONSOLE
LAMP..............................8L-21
SWITCH - REMOVAL, CLUTCH PEDAL
INTERLOCK..........................6-13
SWITCH - REMOVAL, CLUTCH PEDAL
UPSTOP.............................6-15
SWITCH - REMOVAL, DOOR CYLINDER
LOCK..............................8N-41
SWITCH - REMOVAL, DOOR LOCK . . 8N-4,8N-42
SWITCH - REMOVAL, DRIVER HEATED
SEAT ..............................8G-10
SWITCH - REMOVAL, DRIVER SEAT.....8N-12,
8N-55
SWITCH - REMOVAL, EXTERIOR HANDLE
. 8N-11
SWITCH - REMOVAL, FULL OPEN
.......8N-13
SWITCH - REMOVAL, GLOVE BOX LAMP
. . 8L-22
SWITCH - REMOVAL, HEADLAMP
........8L-13
SWITCH - REMOVAL, IGNITION
.........19-14
34 INDEXRS
Description Group-Page Description Group-Page Description Group-Page
Page 2578 of 2585
SWITCH - REMOVAL, LEFT B-PILLAR....8N-32
SWITCH - REMOVAL, MEMORY SET.....8N-13,
8N-56
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE....9-141,
9-54
SWITCH - REMOVAL, PASSENGER
HEATED SEAT .......................8G-14
SWITCH - REMOVAL, PASSENGER SEAT . . 8N-14,
8N-57
SWITCH - REMOVAL, REMOTE..........8N-49
SWITCH - REMOVAL, RIGHT B-PILLAR . . . 8N-32
SWITCH - REMOVAL, SUNROOF........23-123
SWITCH - REMOVAL, WASHER FLUID
LEVEL.............................8R-12
SWITCH - REMOVAL, WINDOW.........8N-65
SWITCH ASSY - DESCRIPTION,
SOLENOID/PRESSURE.........21-237,21s-137
SWITCH ASSY - INSTALLATION,
SOLENOID/PRESSURE.........21-239,21s-139
SWITCH ASSY - OPERATION, SOLENOID/
PRESSURE..................21-237,21s-137
SWITCH ASSY - REMOVAL, SOLENOID/
PRESSURE..................21-238,21s-138
SWITCHES - DESCRIPTION, REMOTE.....8A-12
SWITCHES - DIAGNOSIS AND TESTING,
REMOTE...........................8A-12
SWITCHES - INSTALLATION, REMOTE....8A-14
SWITCHES - OPERATION, REMOTE......8A-12
SWITCHES - REMOVAL, REMOTE........8A-13
SYMBOLS - DESCRIPTION,
INTERNATIONAL....................Intro.-5
SYMBOLS - DESCRIPTION,
INTERNATIONAL.......................0-1
SYNCHRONIZER - DESCRIPTION.......21-114
SYNCHRONIZER - DISASSEMBLY.......21-114
SYNCHRONIZING CABLE ADJUSTMENT,
INSTALLATION.................23-102,23-88
T850 MANUAL TRANSAXLE - ASSEMBLY . . 21-42
T850 MANUAL TRANSAXLE -
DESCRIPTION.......................21-21
T850 MANUAL TRANSAXLE -
DISASSEMBLY.......................21-35
T850 MANUAL TRANSAXLE -
INSTALLATION.......................21-51
T850 MANUAL TRANSAXLE -
OPERATION.........................21-24
T850 MANUAL TRANSAXLE - REMOVAL . . 21-31
T850 MANUAL TRANSAXLE -
SPECIFICATIONS.....................21-56
T850 TRANSAXLE - SPECIAL TOOLS.......6-6
T850 TRANSAXLE - SPECIAL TOOLS.....21-58
TABLE, SPECIFICATIONS -
SPECIFICATIONS.................8N-29,8N-9
TAIL LAMP - INSTALLATION............8L-19
TAIL LAMP - REMOVAL................8L-18
TAIL LAMP UNIT - INSTALLATION.......8L-19
TAIL LAMP UNIT - REMOVAL...........8L-19
TANK - DESCRIPTION, FUEL............14-10
TANK - INSTALLATION, FUEL...........14-12
TANK - OPERATION, FUEL..............14-11
TANK - REMOVAL, FUEL...............14-11
TANK - STANDARD PROCEDURE,
DRAINING FUEL......................14-2
TANK FILLER TUBE - INSTALLATION,
FUEL..............................14-13
TANK FILLER TUBE - REMOVAL, FUEL....14-12
TAPE ATTACHED - INSTALLATION,
EXTERIOR NAME PLATES..............23-51
TAPE ATTACHED - REMOVAL, EXTERIOR
NAME PLATES.......................23-51
TASK MANAGER - DESCRIPTION........25-24
TASK MANAGER - OPERATION..........25-24
TD - INSTALLATION, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-12
TD - REMOVAL, CLUTCH DISC AND
PRESSURE PLATE - 2.5L...............6-11
TEMP SENSOR - DESCRIPTION,
AMBIENT..........................8M-11
TEMP SENSOR - OPERATION, AMBIENT
. . 8M-11
TEMPERATURE CONTROL (ATC) -
INSTALLATION, AUTOMATIC
............24-29
TEMPERATURE CONTROL (ATC) -
REMOVAL, AUTOMATIC
................24-28
TEMPERATURE CONTROL (MTC) -
INSTALLATION, MANUAL
..............24-29
TEMPERATURE CONTROL (MTC) -
REMOVAL, MANUAL
..................24-29TEMPERATURE CONTROL SYSTEM -
OPERATION, AUTOMATIC.............24-112
TEMPERATURE CONTROL SYSTEM -
OPERATION, MANUAL................24-112
TEMPERATURE SENSOR - 2.4L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 2.4L -
INSTALLATION, ENGINE COOLANT........7-21
TEMPERATURE SENSOR - 2.4L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - 3.3/3.8L -
DESCRIPTION, ENGINE COOLANT.........7-21
TEMPERATURE SENSOR - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-22
TEMPERATURE SENSOR - 3.3/3.8L -
REMOVAL, ENGINE COOLANT............7-21
TEMPERATURE SENSOR - DESCRIPTION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - DESCRIPTION,
EVAPORATOR.......................24-27
TEMPERATURE SENSOR - DESCRIPTION,
INFRARED..........................24-29
TEMPERATURE SENSOR - DESCRIPTION,
INLET AIR..........................14-30
TEMPERATURE SENSOR - DIAGNOSIS
AND TESTING, AMBIENT..............8M-12
TEMPERATURE SENSOR - OPERATION,
BATTERY...........................8F-23
TEMPERATURE SENSOR - OPERATION,
EVAPORATOR.......................24-28
TEMPERATURE SENSOR - OPERATION,
INFRARED..........................24-29
TEMPERATURE SENSOR - REMOVAL,
BATTERY.............................8F-23
TEMPERATURE SENSOR -
SPECIFICATIONS, BATTERY.............8F-22
TEMPERATURE SENSOR CIRCUIT -
DIAGNOSIS AND TESTING, AMBIENT....8M-12
TENSION - STANDARD PROCEDURE,
CHECKING POWER STEERING BELT........7-8
TENSION RELEASE - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-58,5s-61
TENSION RESET - STANDARD
PROCEDURE, PARKING BRAKE
AUTOMATIC ADJUSTER............5-59,5s-61
TENSION, SPECIFICATIONS -
ACCESSORY DRIVE BELT................7-5
TENSIONER - 2.4L - INSTALLATION,
BELT ...............................7-10
TENSIONER - 2.4L - REMOVAL, BELT......7-10
TENSIONER - 3.3/3.8L - INSTALLATION,
BELT ...............................7-12
TENSIONER - 3.3/3.8L - REMOVAL, BELT . . . 7-12
TENSIONER - DESCRIPTION, SEAT BELT . . 8O-17
TENSIONER - OPERATION, SEAT BELT....8O-17
TENSIONER & PULLEY - INSTALLATION,
TIMING BELT.........................9-69
TENSIONER & PULLEY - REMOVAL,
TIMING BELT.........................9-68
TERMINAL - INSTALLATION.........8W-01-14
TERMINAL - REMOVAL.............8W-01-14
TERMINAL REPAIR - STANDARD
PROCEDURE, GRID LINE...............8G-4
TEST - 2.5L DIESEL - DIAGNOSIS AND
TESTING, SYSTEM CHARGE LEVEL......24-68
TEST - DIAGNOSIS AND TESTING, A/C
COOL DOWN.........................24-6
TEST - DIAGNOSIS AND TESTING, A/C
PERFORMANCE.......................24-7
TEST - DIAGNOSIS AND TESTING,
CONTROL CIRCUIT..............8F-30,8F-32
TEST - DIAGNOSIS AND TESTING,
COOLING SYSTEM LEAK.................7-2
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMBUSTION PRESSURE
LEAKAGE.........................9-83,9-9
TEST - DIAGNOSIS AND TESTING,
CYLINDER COMPRESSION PRESSURE
. . 9-83,9-9
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT
.......................8F-33,8F-35
TEST - DIAGNOSIS AND TESTING, FEED
CIRCUIT RESISTANCE
............8F-32,8F-34
TEST - DIAGNOSIS AND TESTING,
HEATER PERFORMANCE
...............24-10
TEST - DIAGNOSIS AND TESTING,
POWER STEERING SYSTEM FLOW
AND PRESSURE
......................19-1TEST - DIAGNOSIS AND TESTING, ROAD . . . 8P-3
TEST - DIAGNOSIS AND TESTING,
ROAD.......................21-119,21s-27
TEST - DIAGNOSIS AND TESTING,
STARTING SYSTEM..............8F-28,8F-30
TEST - GASOLINE ENGINES -
DIAGNOSIS AND TESTING, SYSTEM
CHARGE LEVEL......................24-67
TEST - STANDARD PROCEDURE,
IGNITION-OFF DRAW..................8F-13
TEST - STANDARD PROCEDURE,
OPEN-CIRCUIT VOLTAGE...............8F-13
TEST MODE, OPERATION - DRB IIIT
STATE DISPLAY.......................25-9
TESTS - DIAGNOSIS AND TESTING,
CLUTCH AIR PRESSURE........21-122,21s-30
TESTS - DIAGNOSIS AND TESTING,
HYDRAULIC PRESSURE........21-120,21s-28
THEFT SECURITY - DESCRIPTION,
VEHICLE............................8Q-1
THEFT SECURITY - OPERATION, VEHICLE . . 8Q-1
THEFT SECURITY SYSTEM - DIAGNOSIS
AND TESTING, VEHICLE................8Q-3
THERMOSTAT - 2.4L - INSTALLATION,
ENGINE COOLANT.....................7-23
THERMOSTAT - 2.4L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - 3.3/3.8L -
INSTALLATION, ENGINE COOLANT........7-24
THERMOSTAT - 3.3/3.8L - REMOVAL,
ENGINE COOLANT.....................7-23
THERMOSTAT - DESCRIPTION, ENGINE
COOLANT............................7-22
THERMOSTAT - DIAGNOSIS AND
TESTING, ENGINE COOLANT.............7-23
THERMOSTAT - OPERATION, ENGINE
COOLANT............................7-22
THERMOWRAP - DESCRIPTION.........8F-19
THERMOWRAP - INSTALLATION.........8F-19
THERMOWRAP - OPERATION...........8F-19
THERMOWRAP - REMOVAL............8F-19
THIRD ROW - INSTALLATION, BENCH
SEAT RISER........................23-101
THIRD ROW - REMOVAL, BENCH SEAT
RISER............................23-101
THREAD REPAIR - DESCRIPTION, FRONT
CRADLE CROSSMEMBER...............13-9
THREAD REPAIR - STANDARD
PROCEDURE, MANIFOLD STRIPPED......9-145
THREADED HOLE REPAIR -
DESCRIPTION......................Intro.-5
THREADS - STANDARD PROCEDURE,
REPAIR OF DAMAGED OR WORN.....9-10,9-86
THREE PASSENGER BENCH -
INSTALLATION, SEAT BELT BUCKLE -
SECOND ROW.......................8O-15
THREE PASSENGER BENCH - REMOVAL,
SEAT BELT BUCKLE - SECOND ROW.....8O-15
THREE ZONE - DESCRIPTION,
AUTOMATIC..........................24-3
THREE ZONE - DESCRIPTION, MANUAL....24-2
THREE ZONE - OPERATION, MANUAL.....24-5
THREE ZONE ATC - OPERATION..........24-5
THROTTLE BODY - DESCRIPTION........14-35
THROTTLE BODY - INSTALLATION.......14-35
THROTTLE BODY - OPERATION.........14-35
THROTTLE BODY - REMOVAL...........14-35
THROTTLE CONTROL CABLE -
INSTALLATION.......................14-36
THROTTLE CONTROL CABLE - REMOVAL . . 14-35
THROTTLE POSITION SENSOR -
DESCRIPTION.......................14-36
THROTTLE POSITION SENSOR -
OPERATION.........................14-36
TIE ROD - INSTALLATION, OUTER.......19-34
TIE ROD - REMOVAL, OUTER...........19-34
TIMING BELT - INSTALLATION...........9-65
TIMING BELT - REMOVAL...............9-63
TIMING BELT COVER(S) - INSTALLATION . . . 9-62
TIMING BELT COVER(S) - REMOVAL
......9-61
TIMING BELT TENSIONER & PULLEY -
INSTALLATION
........................9-69
TIMING BELT TENSIONER & PULLEY -
REMOVAL
...........................9-68
TIMING CHAIN AND CAMSHAFT
SPROCKET - INSTALLATION
............9-157
TIMING CHAIN AND CAMSHAFT
SPROCKET - REMOVAL
................9-156
RSINDEX35
Description Group-Page Description Group-Page Description Group-Page