CITROEN C CROSSER DAG 2009 Workshop Manual

C O M F O R T
II
54
Returning the second row to the normal position

1. Lower the seat pulling simultane-
ously on the releasing strap
A lo-
cated at the rear of the cushion and
supporting the seat with your hand.
Force may be necessary to carry out these operations.
On vehicles fi tted with a third row, the rear of the cushio n of the second row is fi tted with a low light B .
When the releasing strap is pulled, the light comes on for approximately 10 seconds to light the fl oor at the base of t he
third row.
2. Press on the cushion to put it in
place until it engages.
3. Pull the seat back upright pulling si-
multaneously on the releasing strap
located at the rear of the seat back.

4. After putting the seat back back in
place, push the seat and the seat
back lightly to ensure that they are
secured correctly.

C O M F O R T
II
55
“Lowered seats” configuration

1. Remove the head restraints from the front seats.

2. Raise the rear armrest and remove the load space cover.

3. Move the rear seats as far back as possible.

4. Move the front seats as far forward as possible and tilt their s eat backs fully.

5. Tilt the seat back of the rear seats.
To return the seats to their normal position, carry out these o perations in reverse order.

C O M F O R T
II
56
REAR BENCH SEAT (ROW 3)
The rear bench seat can be folded. It
retracts into a location in the fl oor of the
vehicle. The label on the bench seat back illus-
trates the various steps to be followed
when unfolding and folding the rear
bench seat.
1. Open the tailgate and the lower tail-
gate (refer to the “Access section”).

2. Pull the cover A from the rear and
fi x it to the seat back using the press
stud of the band B .
Unfolding the bench seat
For comfort, it is advisable to fold the
bench seat when its is not is use.

C O M F O R T
II
57

3. Pull the black strap
C located at the
centre of the seat back to raise the
seat back.
4. Pull the black strap
D to release the
bench seat cushion.
5. Tilt the bench seat rearwards.

6. Raise the head restraints. 7. Lift and push the bench seat assem-
bly forwards until it locks.
Undo the press stud of band B to re-
lease the cover.

C O M F O R T
II
58

1. Open the tailgate and the lower tail-
gate (refer to the “Access” section).

2. Lift the cover A and fi x it to the seat
back using the press stud of the
band
B .
3. Unlock the head restraints by sliding
the controls
C and fold them onto
the seat back.
4. Pull the grey strap
D and bring the
bench seat towards you. Press on
the bench seat to lock it.

5. Tilt and push the bench seat for-
wards.
6. Pull the black strap E located at the
centre of the seat back to fold the
seat back.
Undo the press stud of the band B to
put the cover back in place.
Folding the bench seat

C O M F O R T
II
59
EXTERIOR MIRRORS
Electric folding / unfolding
- from inside, with the ignition switch in the “ON” or “ACC” position

 by pressing the control C .
- from inside, with the ignition switch in the “LOCK” position:

 by pressing the control C, within
30 seconds.
- from outside using the remote control:

 by pressing the “closed padlock”
button briefl y 3 times to fold
them,

 by pressing the “open padlock”
button briefl y 3 times to unfold
them.
Adjustment
The mirrors can be adjusted when the
ignition switch is in the “ON” or “ACC”
position.

 Move control
A to the right or to
the left to select the corresponding
mirror.

 Direct control
B in all four direc-
tions to adjust the mirror.
When adjustment is complete, return
control A to the central position. If you switch the engine off then re-
start it with the mirrors folded, they
will unfold automatically when the
vehicle reaches 20 mph (30 km/h).
If the mirrors have been folded man-
ually or electrically after starting the
engine, they are not unfolded auto-
matically.
In this case:

 Press the control C to unfold
them. If you have folded the mirrors
using the control
C , you must
use this control to unfold them,
otherwise the mirrors will not be
locked correctly.

The folding and unfolding of the exte-
rior mirrors can be confi gured via the
colour display “Equipment” menu or
deactivated by a CITROËN dealer.
The mirrors can also be folded manually.

C O M F O R T
II
60
INTERIOR MIRROR
Adjust the mirror by moving it up or
down and/or to the left or right.
The interior mirror has two positions:
- day (normal),
- night (anti-dazzle).
To change from one to the other, push
or pull the lever on the lower edge of
the mirror.
MANUAL STEERING WHEEL
HEIGHT ADJUSTMENT

 Pull the locking lever downwards
(position B ) while supporting the
steering wheel.

 Adjust the steering wheel to the re-
quired height.

 Lock the steering wheel by push-
ing the lever upwards (position A ). The sun visors fold forwards, and to the
side when they are unhooked.
They are fi tted with a courtesy mirror
and a ticket holder.
As a safety precaution, it is
imperative that these opera-
tions are carried out while the
vehicle is stationary.

C O M F O R T
II
62
FRONT INTERIOR LAYOUT

1. Spectacles storage.

2. Storage compartment.

3. Upper glove box with
air conditioning.

4. Lower glove box with lock.

5. Lighter
12 volt socket (120 W max).

6. Armrest with storage compartments
12 volt socket (120 W max).

7. Cup holder.

8. Removable ashtray.

9. Bottle holder.

10. Enclosed storage compartment.

11. Cup holder.

C O M F O R T
II
63
Upper glove box with
air conditioning
Storage box
Press the front part of the lid to open.
To close, fold down the lid until it locks. Press button
A on the lid to open it.
To close it, push the lid up.
It is fi tted with a ventilation nozzle which
can be closed by means of a dial, dis-
tributing conditioned air at the same
temperature as the vents in the passen-
ger compartment.
In cold weather, it is advisable to close
this vent to conserve the ambient air in-
side the passenger compartment.
Spectacles storage
Press the cover to open it.
To close it, push the cover until it locks.

C O M F O R T
II
64
Lower glove box
This is fi tted with a lock.
To unlock it, turn the key to the left.
To open it, pull the handle A .
To close it, push the lid up.
To lock it, turn the key to the right.
It is fi tted with a pen holder and a card
holder.
It is lit on opening when the lights stalk
is activated. Lighter
12 volt socket (120 W max)
When the ignition switch is in the “ON”
or “ACC” position, press the lighter.
After a moment you hear a click when
the lighter pops out.
When the lighter socket is used to con-
nect electrical equipment, ensure that
this equipment operates correctly with
a voltage of 12 volts and has an electri-
cal power of 120 W maximum.
The prolonged use of electri-
cal equipment without running
the engine may discharge the
battery. Armrest with storage compartments
12 volt socket (120 W max)
Upper storage compartment
Pull the right-hand lever to open the
storage compartment lid, which serves
as an armrest.
To close, fold down the lid until it locks.