Citroen C3 PICASSO DAG 2008.5 1.G Owner's Manual
Manufacturer: CITROEN, Model Year: 2008.5, Model line: C3 PICASSO DAG, Model: Citroen C3 PICASSO DAG 2008.5 1.GPages: 207, PDF Size: 11.01 MB
Page 141 of 207
128
PRACTICAL INFORMATION
Engine compartment fuses
The fuse box is placed in the engine
compartment near the battery (left-hand
s i d e ) .
Access to the fuses
U n c l i p t h e c o v e r .
Change the fuse (see correspond-
i n g p a r a g r a p h ) .
W h e n y o u h a v e fi n i s h e d , c l o s e t h e
cover carefully to guarantee the
s e a l i n g o f t h e f u s e b o x . Fuse table
Fuse N° Rating Functions
F1 20 A Engine control unit supply, cooling fan unit control,
m u l t i f u n c t i o n e n g i n e c o n t r o l m a i n r e l a y .
F2 15 A H o r n .
F3 10 A F r o n t / r e a r w a s h - w i p e .
F4 20 A D a y t i m e r u n n i n g l a m p s .
F5 15 A D i e s e l h e a t e r ( d i e s e l e n g i n e ) , f u e l p u m p ( p e t r o l
engine)
F6 10 A ABS/ESP control unit, ABS/ESP cut-off relay,
s e c o n d a r y s t o p s w i t c h .
F7 10 A E l e c t r i c a l p o w e r s t e e r i n g .
F8 25 A S t a r t e r c o n t r o l .
F9 10 A S w i t c h i n g a n d p r o t e c t i o n u n i t ( D i e s e l ) .
F10 30 A D i e s e l e n g i n e i n j e c t i o n p u m p v a l v e , i n j e c t o r s a n d
ignition coils (petrol engine)
F11 40 A A i r c o n d i t i o n i n g b l o w e r .
Page 142 of 207
129
PRACTICAL INFORMATION
Fuse N° Rating Functions
F12 30 A W i n d s c r e e n w i p e r s s l o w / f a s t s p e e d .
F13 40 A B u i l t - i n s y s t e m s i n t e r f a c e s u p p l y ( i g n i t i o n p o s i t i v e ) .
F14 30 A V a l v e t r o n i c s u p p l y ( p e t r o l ) .
F15 10 A R i g h t - h a n d m a i n b e a m h e a d l a m p .
F16 10 A L e f t - h a n d m a i n b e a m h e a d l a m p .
F17 15 A L e f t - h a n d d i p p e d h e a d l a m p .
F18 15 A R i g h t - h a n d d i p p e d h e a d l a m p .
F19 15 A Multifunction engine control supply (petrol engine),
a i r c o o l i n g s o l e n o i d v a l v e s ( D i e s e l ) .
F20 10 A Multifunction engine control supply (petrol engine),
T u r b o p r e s s u r e r e g u l a t i o n v a l v e ( D i e s e l ) , e n g i n e
c o o l a n t l e v e l d e t e c t o r ( D i e s e l ) .
F21 5 A Fan assembly control supply, APC, ABS ESP
r e l a y s .
Page 143 of 207
130
PRACTICAL INFORMATION
Table of maxi-fuses
Fuse N° Rating
Functions
MF1 * 60 A F a n a s s e m b l y .
MF2 * 30 A A B S / E S P c o n t r o l u n i t .
MF3 * 30 A A B S / E S P c o n t r o l u n i t .
MF4 * 60 A B u i l t - i n S y s t e m s I n t e r f a c e ( B S I ) s u p p l y .
MF5 * 60 A B u i l t - i n S y s t e m s I n t e r f a c e ( B S I ) s u p p l y .
MF6 * - N o t u s e d .
MF7 * - P a s s e n g e r c o m p a r t m e n t f u s e b o x .
MF8 * - N o t u s e d .
* T h e m a x i - f u s e s p r o v i d e a d d i t i o n a l p r o t e c t i o n f o r t h e e l e c t r i c a l s y s t e m s . A l l w o r k o n t h e m a x i - f u s e s m u s t b e c a r r i e d o u t b y a
C I T R O Ë N d e a l e r .
Page 144 of 207
131
PRACTICAL INFORMATION
BATTERY
Procedure for charging your battery
w h e n i t i s fl a t o r f o r s t a r t i n g t h e e n g i n e
u s i n g a n o t h e r b a t t e r y .
Access to the battery Starting using another battery
Connect the red cable to the posi-
t i v e t e r m i n a l ( + ) o f t h e fl a t b a t t e r y A ,
then to the positive terminal (+) of
the slave battery B .
Connect one end of the green or
black cable to the negative terminal
(-) of the slave battery B .
Connect the other end of the green
or black cable to the negative termi-
n a l ( - ) o f t h e fl a t b a t t e r y A .
S t a r t t h e s l a v e v e h i c l e .
Operate the starter of the broken
down vehicle and let the engine
r u n .
Wait until the engine returns to idle
a n d d i s c o n n e c t t h e c a b l e s .
The battery is located under the bon-
n e t .
To gain access to it:
open the bonnet using the interior
lever, then the exterior lever,
secure the bonnet strut,
remove the plastic cover to gain ac-
cess to the two terminals,
unclip the fuse box to remove the
b a t t e r y , i f n e c e s s a r y .
Page 145 of 207
i
!
!
132
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
sulphate (whitish or greenish deposit),
r e m o v e t h e m a n d c l e a n t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
t e m s . H o w e v e r , i f s l i g h t d i f fi c u l t i e s
are encountered following this op-
e r a t i o n , c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 146 of 207
i
!
!
132
PRACTICAL INFORMATION D o n o t d i s c o n n e c t t h e t e r m i n a l s
w h i l e t h e e n g i n e i s r u n n i n g .
D o n o t c h a r g e t h e b a t t e r i e s w i t h o u t
d i s c o n n e c t i n g t h e t e r m i n a l s fi r s t .
The batteries contain harmful sub-
stances such as sulphuric acid and
l e a d . T h e y m u s t b e d i s p o s e d o f i n
accordance with regulations and
must not, in any circumstances, be
d i s c a r d e d w i t h h o u s e h o l d w a s t e .
Take used remote control batteries
and vehicle batteries to a special
c o l l e c t i o n p o i n t .
Charging the battery using a
battery charger
D i s c o n n e c t t h e b a t t e r y f r o m t h e v e -
h i c l e .
Follow the instructions for use pro-
vided by the manufacturer of the
c h a r g e r .
Reconnect starting with the nega-
t i v e t e r m i n a l ( - ) .
Check that the terminals and connec-
t o r s a r e c l e a n . I f t h e y a r e c o v e r e d w i t h
sulphate (whitish or greenish deposit),
r e m o v e t h e m a n d c l e a n t h e m .
At the risk of discharging the bat-
tery, the deactivated functions can
b e r e a c t i v a t e d m a n u a l l y .
System which manages the use of cer-
tain functions in relation to the level of
c h a r g e r e m a i n i n g i n t h e b a t t e r y .
When the vehicle is being driven, the
load reduction function temporarily deac-
tivates certain functions, such as the air
c o n d i t i o n i n g , t h e r e a r s c r e e n d e - i c i n g . . .
The deactivated functions are reacti-
vated automatically as soon as condi-
t i o n s p e r m i t .
It is advisable to disconnect the
battery if the vehicle is to be left un-
u s e d f o r m o r e t h a n o n e m o n t h . Before disconnecting the battery
Wait 2 minutes after switching off
the ignition before disconnecting
t h e b a t t e r y .
Close the windows and the doors
b e f o r e d i s c o n n e c t i n g t h e b a t t e r y .
Following reconnection of the
battery
Following reconnection of the bat-
tery, switch on the ignition and wait
1 minute before starting to permit
initialisation of the electronic sys-
t e m s . H o w e v e r , i f s l i g h t d i f fi c u l t i e s
are encountered following this op-
e r a t i o n , c o n t a c t a C I T R O Ë N d e a l e r .
Referring to the corresponding sec-
tion, you must yourself reinitialise:
- the remote control key,
- the GPS satellite navigation
s y s t e m .
Page 147 of 207
i
!
133
PRACTICAL INFORMATION
A fl a t b a t t e r y p r e v e n t s t h e e n g i n e
from starting (refer to the corre-
s p o n d i n g p a r a g r a p h ) .
If the telephone is being used at
the same time with the MyWay audio
navigation, it will be interrupted after
1 0 m i n u t e s .
ENERGY ECONOMY MODE
System which manages the duration of
use of certain functions to conserve a
s u f fi c i e n t l e v e l o f c h a r g e i n t h e b a t t e r y .
After the engine has stopped, you can
still use functions such as the audio
e q u i p m e n t , w i n d s c r e e n w i p e r s , d i p p e d
h e a d l a m p s , c o u r t e s y l i g h t s , e t c . f o r a
maximum combined duration of thirty
m i n u t e s . Exiting economy mode
These functions are reactivated auto-
m a t i c a l l y n e x t t i m e t h e v e h i c l e i s d r i v e n .
In order to resume the use of these
functions immediately, start the en-
g i n e a n d l e t i t r u n f o r a f e w m i n u t e s .
The time available to you will then be
double the duration for which the en-
g i n e i s l e f t r u n n i n g . H o w e v e r , t h i s p e r i o d
w i l l a l w a y s b e b e t w e e n fi v e a n d t h i r t y
m i n u t e s .
Switching to economy mode
Once the thirty minutes are over, a
message appears on the multi-function
display indicating that the vehicle has
switched to economy mode and the ac-
t i v e f u n c t i o n s a r e p u t o n s t a n d b y .
CHANGING A WIPER BLADE
Procedure for replacing a worn wiper
blade with a new one without the use
o f t o o l s .
Removing a front or rear wiper
blade
R a i s e t h e c o r r e s p o n d i n g w i p e r a r m .
U n c l i p t h e w i p e r b l a d e a n d r e m o v e i t .
Fitting a front or rear wiper blade
At the front, check the size of the
wiper blade as the shorter blade is
fi t t e d o n t h e r i g h t - h a n d s i d e o f t h e
v e h i c l e .
Put the corresponding new wiper
b l a d e i n p l a c e a n d c l i p i t .
F o l d d o w n t h e w i p e r a r m c a r e f u l l y .
Before removing a front wiper blade
Within one minute after switching off
the ignition, operate the wipers stalk
to position the wiper blades in the
v e r t i c a l p o s i t i o n .
This position must be used in order to
avoid damaging the wiper blade and the
b o n n e t .
After fitting a front wiper blade
S w i t c h o n t h e i g n i t i o n .
Operate the wipers stalk again to
p a r k t h e w i p e r b l a d e s .
Page 148 of 207
i!
134
PRACTICAL INFORMATION
TOWING THE VEHICLE
Access to the tools Towing your vehicle
On the front bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
P l a c e t h e g e a r l e v e r i n n e u t r a l .
On the rear bumper, unclip the cover
b y p r e s s i n g a t t h e b o t t o m .
S c r e w t h e t o w i n g e y e i n f u l l y .
I n s t a l l t h e t o w b a r .
Switch on the hazard warning lights
o n t h e t o w e d v e h i c l e .
Towing another vehicle
The towing eye is installed under the
b o o t fl o o r .
To gain access to it:
open the boot,
r e m o v e t h e m o v a b l e b o o t fl o o r ,
lift up the boot carpet,
remove the towing eye from the tool
h o l d e r . When towing with all four wheels on
t h e g r o u n d , a l w a y s u s e a t o w b a r .
When towing with only two wheels
on the ground, always use profes-
s i o n a l l i f t i n g e q u i p m e n t .
When towing with the engine off,
there is no longer any braking or
s t e e r i n g a s s i s t a n c e .
Failure to observe this special con-
dition could result in damage to
certain braking components and
the absence of braking assistance
t h e n e x t t i m e t h e e n g i n e i s s t a r t e d .
Procedure for having your vehicle towed
or for towing another vehicle using a re-
m o v a b l e t o w i n g e y e .
Page 149 of 207
i
i
135
PRACTICAL INFORMATION
TOWING A TRAILER, A CARAVAN, ETC.
Your vehicle is primarily designed for
transporting people and luggage, but it
m a y a l s o b e u s e d f o r t o w i n g a t r a i l e r . Driving advice
The maximum towing load on a long
slope depends on the gradient and the
o u t s i d e t e m p e r a t u r e .
In all cases, pay attention to the coolant
t e m p e r a t u r e .
Side wind
Take into account the increased
s e n s i t i v i t y t o s i d e w i n d .
Cooling
Towing a trailer on a slope increases
t h e t e m p e r a t u r e o f t h e c o o l a n t .
As the fan is electrically controlled, its
cooling capacity is not dependent on
t h e e n g i n e s p e e d .
To lower the engine speed, reduce
y o u r s p e e d . Braking
Towing a trailer increases the braking
d i s t a n c e .
Tyres
Check the tyre pressures of the towing
vehicle and of the trailer, observing the
r e c o m m e n d e d p r e s s u r e s .
Lights
Check the electrical signalling on
t h e t r a i l e r .
The rear parking assistance will
be deactivated automatically if an
o r i g i n a l C I T R O Ë N t o w b a r i s u s e d .
If the warning light and the
STOP warning light come
on, stop the vehicle and
switch off the engine as
s o o n a s p o s s i b l e .
Towbar suited to the attachment of a
trailer or caravan with additional signal-
l i n g a n d l i g h t i n g .
Distribution of loads
D i s t r i b u t e t h e l o a d i n t h e t r a i l e r s o
that the heaviest items are as close
as possible to the axle and the nose
weight approaches the maximum
p e r m i t t e d w i t h o u t e x c e e d i n g i t .
Air density decreases with altitude, thus
r e d u c i n g e n g i n e p e r f o r m a n c e . A b o v e
1 000 metres, the maximum towing load
must be reduced by 10 % and so on for
e v e r y 1 0 0 0 m e t r e s o f a l t i t u d e .
R e f e r t o t h e " T e c h n i c a l D a t a " s e c t i o n f o r
details of the weights and towing loads
w h i c h a p p l y t o y o u r v e h i c l e .
D r i v i n g w i t h a t r a i l e r s u b j e c t s t h e t o w i n g
v e h i c l e t o m o r e s i g n i fi c a n t s t r e s s a n d i t s
d r i v e r m u s t b e p a r t i c u l a r l y c a r e f u l .
We recommend the use of original
CITROËN towbars and their har-
nesses that have been tested and
approved from the design stage
o f y o u r v e h i c l e , a n d t h a t t h e fi t -
ting of the towbar is entrusted to a
C I T R O Ë N d e a l e r .
I f t h e t r a i l e r i s n o t fi t t e d b y a
CITROËN dealer, it is imperative
t h a t i t i s fi t t e d u s i n g t h e e l e c t r i c a l
p r e - e q u i p m e n t i n s t a l l e d a t t h e r e a r
of the vehicle, in accordance with
t h e m a n u f a c t u r e r ’ s i n s t r u c t i o n s .
Page 150 of 207
i
136
PRACTICAL INFORMATION
FITTING ROOF BARS
Maximum authorised weight on
t h e r o o f r a c k : 6 0 k g .
If the height exceeds 40 cm, adapt
the speed of the vehicle to the
p r o fi l e o f t h e r o a d t o a v o i d d a m -
a g i n g t h e r o o f b a r s a n d t h e fi x i n g s
o n t h e r o o f .
Be sure to refer to national legis-
lation in order to comply with the
regulations for transporting ob-
jects which are longer than the
v e h i c l e .
T o fi t l o n g i t u d i n a l a n d / o r t r a n s v e r s e r o o f
b a r s , v i s i t y o u r C I T R O Ë N d e a l e r .