warning Citroen C4 2005 2.G User Guide

Downloaded from www.Manualslib.com manuals search engine 156
ENGINE
B1BP2LSC
B1BP2LTC
AUXILIARY EQUIPMENT DRIVE BELT
Engines: KFU - NFU
Tools.
[1]Pliers for removing plastic pegs: 7504 -T
[2]Belt tension measuring instrument (SEEM) : 4122 -T
[3]Compression lever for dynamic tensioner: (-).0194.D
[4] Peg for dynamic tensioner roller of Ø 4 mm : (-) 0194.F
WARNING: (With or without air conditioning)
The auxiliaries drive belt cannot be re-used
with a manual tensioner roller.
The auxiliaries drive belt can be re-usedwith a dynamic tensioner roller.
Removing.
Raise and support the vehicle, front wheels hanging.
Disconnect the battery.
Remove the front RH wheel and the front RH splash-shield, using tool [1].
V
ehicle without air conditioning.Slacken bolts (2), screw (3)and the tensioning screw (1).
Push back the alternator towards the engine.
Remove the auxiliary equipment drive belt.
Refitting.
Refit the new auxiliary equipment drive belt.
Respect the following sequence: Crankshaft pinion, alternator pulley.
Position tool [2]on the belt.
Tighten the screw (1)to tension the belt to: 120 ± 4 SEEM units.
Tighten screw (3), bolts (2).
Remove tool [2].
Complete the refitting.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 156

Downloaded from www.Manualslib.com manuals search engine 162
ENGINEAUXILIARY EQUIPMENT DRIVE BELT
Engines: 6FZ - RFN
Without air conditioningWith air conditioning
Tool.
[1] Pliers for removing plastic pegs: 7504-T
Remove the belt.
Detension the belt (3)by turning the screw (2)of the tensioner roller (1)
(anti-clockwise).
The screw (2)
(WARNING: not left hand screw).
Remove the belt (3), while keeping the tensioner roller (1)tight.
Refit the belt.
Refit the belt (3), while keeping the tensioner roller (1)tight.
Release the tensioner roller (1).
B1BP23PCB1BP23QCB1BP23PCB1BP23RC
XSARA - XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 162

Downloaded from www.Manualslib.com manuals search engine 165
ENGINE
XSARA
AUXILIARY EQUIPMENT DRIVE BELT
Tools.
[1] Dynamic tensioner compression lever: (-).0188.Z
[2] Peg for dynamic tensioner roller: (-).0194.F
Removing.
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Remove:
- the front RH wheel.
- the sound insulation under the engine.
- the splash-shield.
WARNING: Mark the direction of fitting of the accessories belt if it is to be re-used.
Compress the dynamic tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Peg at «b». using tool [2].
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without
tight spots).
B1BP2VZD
Engines: 8HX - 8HZ
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 165

Downloaded from www.Manualslib.com manuals search engine 166
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Refitting.
WARNING: If the accessories belt is being re-used, respect the direction of fitting of the belt.
Refit the accessories belt.
Compress the tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Check that the belt is correctly positioned in the grooves of the different pulleys.
Complete the refitting in the opposite direction to removal.
Engines: 8HX - 8HZ
B1BP2VZD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 166

Downloaded from www.Manualslib.com manuals search engine 167
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Tools.
[1]Dynamic tensioner roller lever (DV6 TED4engine): (-).0194-E3
[1a]Dynamic tensioner roller lever (DV6 ATED4engine): (-).0194-E1
[1b]Lever extension (DV6 ATED4engine): (-).0194-E2
[2] Dynamic tensioner roller locking peg: (-).0194-F
IMPERATIVE: Respect the safety and cleanliness requirements specific to High pressure
Diesel injection (HDi) engine versions.
Markings on the dynamic tensioner roller.
«a»position «maximum wear»of the auxiliaries drive belt.
«b»Nominal position.
Removing.
WARNING: Mark the direction of fitting of the auxiliaries drive belt in the case of re-use of
the belt.
Compress the dynamic tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Peg using tool [2]at «d».
Keep the dynamic tensioner roller (1)compressed and remove the auxiliaries drive belt.
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 167

Downloaded from www.Manualslib.com manuals search engine 168
ENGINE
B1EP18UD
B1BP3ACD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HX - 9HY - 9HZ
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the auxiliaries drive belt.
Compress the tensioner roller (1)by acting at «c»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure that the auxiliaries drive belt is correctly positioned in the grooves
of the various pulleys.
Refit:
- The front RH wheel.
- The sound-deadening under the engine.
- Reconnect the battery.
IMPERATIVE: Carry out the operations that are necessary following a reconnection of the
battery
(see corresponding operation).
C4
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 168

Downloaded from www.Manualslib.com manuals search engine 169
ENGINE
B1BP2Z6D
B1BP2ZCD
AUXILIARY EQUIPMENT DRIVE BELT
Engines: 9HZ - 9HY
Tools.
[1]Dynamic tensioner compression lever: (-).0188.Z
[2]Peg for dynamic tensioner roller: (-).0194.F
Removing.
Remove the front RH wheel, the under-engine sounddeadening and the splash-shield.
V
ehicle with air conditioning.
WARNING: Mark the direction of fitting of the accessories drive belt, if it is to be re-used.
Compress the tensioner roller(1)by acting at «a»
(clockwise), using tool [1].
Peg at «b», using tool [2].
Remove the accessories drive belt.
IMPERATIVE: Check that the rollers (1) and (2) can turn freely
(without play and without tight
spots).
Refitting.
WARNING: Belt to be re-used, mark the direction of fitting of the belt.
Refit the accessories drive belt.
Compress the tensioner roller (1)by acting at «a»
(clockwise), using tool [1].
Remove tool [2].
IMPERATIVE: Make sure the belt is correctly positioned in the grooves of the various pulleys.
Complete the refitting in the opposite order to removal.
XSARA PICASSO
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 169

Downloaded from www.Manualslib.com manuals search engine 172
ENGINEXSARA
AUXILIARY EQUIPMENT DRIVE BELT
Power-assisted steering, without air conditioning
Tool.
[1] Belt tension measuring instrument: 4122-T
Removal.
WARNING: If the belt is to be reused, measure the tension before removal.
Loosen:
- the screw (1).
- the nut (2).
NOTE:The tensioner arm (3)must be against the alternator.
Remove the belt.
B1BP1SHD
Engine: WJY
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 172

Downloaded from www.Manualslib.com manuals search engine 173
ENGINE
AUXILIARY EQUIPMENT DRIVE BELT
Engine: WJY
Power-assisted steering, without air conditioning (continued)
XSARA
Refitting.
Refit the belt.
Place the tool [1]on belt at "f".
WARNING: Position tool [1] with the knob downwards.
Tighten the nut (2)to obtain a value of:
Reused belt:
- Keep the value taken at removal.
New belt:
- Tension should be 110 SEEMunits.
- Tighten the screw (1)to 9.5 m.daN.
- Check belt tension, using tool [1].
Tension should be 144 ± 3 SEEMunits.
- Remove the tool [1].
- Start the engine and run it for 10 seconds.
- Stop the engine.
- Place the tool [1]on the belt at "f".
- Tension should be 130 ± 4 SEEMunits.
- Remove the tool [1].
B1BP1SJD
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 173

Downloaded from www.Manualslib.com manuals search engine 176
ENGINEXSARA - XSARA PICASSO AUXILIARY EQUIPMENT DRIVE BELT
Engines: RHY - RHZ
Without air conditioning
B1BP1YKD
Tools.
[1] Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mmpeg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2
[4]Dynamic tensioner compression lever: (-).0188.Z
Removing.
Re-use of belt.
WARNING: Mark the direction the belt was fiited in case of re-use of the same belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Keep the tensioner roller (2)compressed and remove the belt.
No re-use of belt.
Compress the tensioner roller (2)by action at «a»
(in anti-clockwise direction), tool [4].
Peg using tool [2]at «b».
Keep the tensioner roller (2)compressed and remove the belt.
Loosen the screw (1).
Angl.-t2-page135-239-2005 9/01/06 10:14 Page 176