display Citroen C4 2016 2.G Workshop Manual

180
C4-2_en_Chap06_conduite_ed02-2015
SituationsConsequences
To   apply   the   electric   parking   brake:
F
 
i
mmobilise   the   vehicle   and   switch   off   the   ignition.
F
 
p
ull   the   control   for   at   least   5   seconds   or   until   application   is   complete.
F
 
s
witch   on   the   ignition   and   check   the   switching   on   of   the   electric   parking  
b

rake   warning   lamps.
The
  application   is   slower   than   during   normal   operation.
To
  release   the   electric   parking   brake:
F
 
s
witch   on   the   ignition.
F
 
p
ull   the   control   and   hold   it   for   approximately   3   seconds   then   release   it.
If
  the   braking   warning   lamp   is   flashing   or   if   the   warning   lamps   do   not   come  
o

n   with   the   ignition   on,   these   procedures   will   not   work.   Place   the   vehicle  
o

n   level   ground   and   have   it   checked   by   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
and possibly
flashing
Display
 
of
 
the
 
message
 
" Parking brake fault "
  and   of   the   following  
w

arning
 lam

ps: -
 
O
nly   the   automatic   application   on   switching   off   the   engine   and   automatic  
r

elease   on   acceleration   functions   are   available.
-
 
T
he   manual   application/release   of   the   electric   parking   brake   and   the  
e

mergency   braking   are   not   available.
and possibly
flashing
Battery
 
fault: -
 I

f   the   battery   warning   lamp   comes   on   you   must   stop   immediately   as   soon   as
 t

he   traffic   allows.   Stop   and   immobilise   your   vehicle   (if   necessary,   place   the
 t

wo   chocks   under   the   wheels).
-
 
A
pply   the   electric   parking   brake   before   switching   off   the   engine.
Driving

182
C4-2_en_Chap06_conduite_ed02-2015
Automatic gearbox
Gear selection gate
1. Gear  selector.
2. B utton " T" (snow) .
3.
B

utton " S" (spor t) .
4.
 P

osition   markings   for   the   gear   selector.P.
 Pa

rk.
-  
I
mmobilisation   of   the   vehicle,   parking   brake  
o

n   or   off.
-  
S
tarting   the   engine.
R.
 R
everse.
-  
R
eversing   manoeuvres,   vehicle   stationary,  
e

ngine   at   idle.
N.
 N
eutral.
-  
I
mmobilisation   of   the   vehicle,   parking   brake  
o

n.
-  
S
tarting   the   engine.
D.
 A
utomatic
 ope
ration.
M.+ / -
   M
anual   operation   with   sequential  
c

hanging   of   the   six   gears.
F  
P
ush   for wards   to   change   up   through   the  
g

ears.
or
F  P ull   backwards   to   change   down   through  
t

he   gears.
Gear selector positions
When you move the selector in the gate to select   a   position,   the   corresponding   indicator  
c

omes   on   in   the   instrument   panel.
P
 
Pa
rk
R
Reverse
N
Neutral
D
 
D
rive   (automatic   driving)
S

Sp
ort
 pro
gramme
T

S
now
 pro
gramme
1 to 6
   Gear   engaged   during   manual   operation
-
 
I
nvalid   value   during   manual   operation
Displays in the instrument
panelSix speed  automatic  gearbox  which  of fers  a  choice b
etween   the   comfort   of   fully   automatic   operation, e

nhanced   by   sport   and   snow   programmes,   and
 t

he   pleasure   of   manual   gear   changing.
Two
  driving   modes   are   offered:
-

a
utomatic operation for electronic
management
  of   the   gears   by   the   gearbox,  
w

ith a sport
 
programme   for   a   more  
d

ynamic   style   of   driving   and   a   snow
programme
  to   improve   driving   when  
t

raction is poor,
-

m
anual
 
operation   for   sequential   changing  
o

f   the   gears   by   the   driver.
Driving

183
C4-2_en_Chap06_conduite_ed02-2015
Moving off
If position N is engaged inadvertently while   driving,   allow   the   engine   to  
r

eturn   to   idle   then   engage   position   D to
accelerate. F

Sel
ect position D for automatic
 c
hanging
 o

f   the   six   gears.
The   gearbox   then   operates   in   auto-adaptive  
m

ode,   without   any   intervention   on   the   part  
o

f   the   driver.   It   continuously   selects   the   most  
s

uitable   gear   according   to   the   style   of   driving,  t
he profile of the road and the load in the
vehicle.
For
  maximum   acceleration   without   touching  
t

he selector, press the accelerator pedal down
fully
  (kick   down).   The   gearbox   changes   down  
a

utomatically   or   maintains   the   gear   selected  
u

ntil   the   maximum   engine   speed   is   reached.
On
  braking,   the   gearbox   changes   down  
a

utomatically   to   provide   effective   engine  
b

raking.
If you release the accelerator sharply, the
gearbox
  will   not   change   to   a   higher   gear   for  
s

afety   reasons.
When
  the   engine   is   running   at   idle,   with  
t

he   brakes   released,   if   position   R,
D
or
M   is   selected,   the   vehicle   moves  
e

ven   without   the   accelerator   being  
p

ressed.
Never leave children unsupervised in
the
  vehicle   when   the   engine   is   running.
When
  carrying   out   maintenance   with  
t

he   engine   running,   apply   the   parking  
b

rake   and   select   position   P.
Never select position N while the
vehicle
  is   moving.
Never select positions P or R unless the
vehicle
  is   completely   stationary.
If
  the   parking   brake   does   not   release  
a

utomatically,   check   that   the   front   doors  
a

re   fully   closed.
F
 
W

ith
 
your
 
foot
 
on
 
the
 
brake,
 
select
 
p

osition


P or N
.
F
 
S

tart
 
the
 
engine.
If this procedure is not followed, an audible
signal
 
is
 
heard,
 
accompanied
 
by
 
a
 
message
 
in
 
t

he
 
instrument
 
panel
 
screen.
F
 W
ith
 
the
 
engine
 
running,
 
press
 
the
 
brake
 ped
al.
F

Sel

ect position R , D or M.
Automatic operation
The parking brake is released manually, the v
ehicle   moves   off.
If
  the   parking   brake   is   on   and   automatic   mode  
i

s   activated,   accelerate   progressively.
If you do not press the brake pedal when trying   to   move   the   gear   selector   out o

f position P ,
  this   warning   lamp   or   this
 s

ymbol
 ap

pears
 in t
he
 in
strument
 pan
el
 a
ccompanied
 b

y
 
a
 
message,   flashing   of   the   P
 
symbol,   the   display   of
 a

 
message
  and   an   audible   signal.
F Check  that   the   display   in   the   instrument  p
anel   agrees   with   the   position   engaged.
F
 
G
radually   release   the   brake   pedal.
6
Driving

185
C4-2_en_Chap06_conduite_ed02-2015
Manual operation
D disappears and the gears engaged   appear   in   succession   on  
t

he   instrument   panel.
Invalid value during manual
operation
This symbol is displayed if a gear is   not   engaged   correctly   (selector  
b

etween   two   positions).
Stopping the vehicle
If the selector is not in position P ,
when   the   driver's   door   is   opened   or  
a

pproximately   45   seconds   after   the  
i

gnition   is   switched   off,   there   is   an  
a

udible   signal   and   a   message   appears.
F

R
eturn the selector to position P ;
 
t

he   audible   signal   stops   and   the  
m

essage
 d
isappears.
F

Sel

ect position M for sequential
 c

hanging
 o

f
 
the
 
six
 
gears.
F

P

ush the selector towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the selector towards the -
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 p
ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 t
emporarily
 
in
 
automatic
 
mode.
If
 
the
 
engine
 
speed
 
is
 
too
 
low
 
or
 
too
 
high,
 
the
 
g

ear
 
selected
 
flashes
 
for
 
a
 
few
 
seconds,
 
then
 
t

he
 
actual
 
gear
 
engaged
 
is
 
displayed.
When
 
the
 
vehicle
 
is
 
stationary
 
or
 
moving
 
v

ery
 
slowly,
 
the
 
gearbox
 
selects
 
gear
 
1
automatically.
It is not necessary to release the accelerator
when
 c

hanging
 g

ear.
It
 
is
 
possible
 
to
 
change
 
from
 
position
 
D
(automatic)
 
to
 
position
 
M
 
(manual)
 
at
 
any
 
time.
The
 
sport
 
and
 
snow
 
programmes
 
do
 
not
 
o

perate
 
in
 
manual
 
mode. Before
 
s
witching  
o
ff  
t
he  
e
ngine,  
p
ut  
t
he  
s
elector  
i

n position P or N   to   place   the   gearbox   in  
neu

tral.
In
 
both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle,   unless   it   is   programmed  
t

o
 
automatic   mode.
6
Driving

187
C4-2_en_Chap06_conduite_ed02-2015
Gear shift indicator*
Depending on the driving situation and your vehicle's   equipment,   the   system   may   advise  
y

ou   to   skip   one   (or   more)   gear(s).   You   can  
f

ollow   this   instruction   without   engaging   the  
i

ntermediate
 g
ears.
The
  gear   engagement   recommendations   must  
n

ot   be   considered   compulsory.   In   fact,   the  
c

onfiguration   of   the   road,   the   amount   of   traffic  
a

nd   safety   remain   determining   factors   when  
c

hoosing   the   best   gear.   Therefore,   the   driver  
r

emains   responsible   for   deciding   whether   or   not  
t

o   follow   the   advice   given   by   the   system.
This
  function   cannot   be   deactivated. -
 
Y
ou   press   the   accelerator   pedal.
Example:
-
 Y ou   are   in   third   gear.
-
 
T
he   system   may   suggest   that   you   engage  
a

  higher   gear.
The
  information   appears   in   the   instrument  
p

anel   in   the   form   of   an   arrow.
System
  which   reduces   fuel   consumption   by   recommending   the   most   appropriate   gear.
With   an   automatic   gearbox,   the   system   is   only  
a

ctive   in   manual   mode.
* Depending
  on   engine.
On
  vehicle   fitted   with   a   manual   gearbox,  
t

he   arrow   may   be   accompanied   by   the   gear  
re

commended. The
  system   adapts   its   gear   change  
r

ecommendation   according   to   the  
d

riving   conditions   (slope,   load, ...)   and  
t

he   demands   of   the   driver   (power,  
a

cceleration,   braking, ...).
The
  system   never   suggests:
-
 
e
ngaging   first   gear,
-
 enga

ging
 r
everse
 g
ear.
Operation
On BlueHDi Diesel 150 versions with
manual  gearbox,   the   system   may  
s

uggest   changing   into   neutral   so   that  
t

he   engine   can   go   into   standby   (STOP  
m

ode   with   Stop   &   Start),   in   certain  
d

riving   conditions.   In   this   case,   N is
displayed
  in   the   instrument   panel.
6
Driving

189
C4-2_en_Chap06_conduite_ed02-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate   the   system.
This
  is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   the   display   of   a  
m

essage.
Special cases: START invoked
automatically
The "ECO"  warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an automatic gearbox:
●
 
g

ear   selector   in   position   D or M, when
you
  release   the   brake   pedal,
●
 
o

r
 
gear   selector   in   position   N   and   brake  
p

edal   released,   when   you   place   the   gear  
s

elector in position D or M ,
●
 
o

r
 
when   you   engage   reverse   gear.For
  safety   reasons   or   to   ensure   smooth  o
peration,   START   mode   is   invoked  
a

utomatically
 w
hen:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15   mph  
(

25   km/h)   with   a   manual   gearbox   (3   km/h  
(

2   mph)   with   PureTech   130   petrol   and  
B

lueHDi   Diesel   115   and   120   versions)   or  
2 m

ph   (3   km/h)   with   an   automatic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case the "ECO"
 

warning   lamp  
f

lashes   for   few   seconds,   then   goes  
o

f f.
This operation is perfectly normal.
With
  a   manual   gearbox   in   STOP   mode,  
i

f
 
a
  gear   is   engaged   without   fully  
d

epressing   the   clutch   pedal,   a   warning  
l

amp   comes   on   or   an   alert   message  
i

s
 
displayed   asking   you   to   depress   the  
c

lutch   pedal   to   restart   the   engine. If
  the   system   has   been   deactivated  
i

n   STOP   mode,   the   engine   restarts  
i

mmediately.
6
Driving

190
C4-2_en_Chap06_conduite_ed02-2015
Maintenance
In the event of a malfunction with the system, the "ECO OFF"   switch   warning   lamp   flashes,  
t

hen   comes   on   continuously.
have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
This system requires the use of a 12 V battery of   specific   technology   and   characteristics  
(

reference   numbers   available   from   a   CITROËN  
d

ealer   or   a   qualified   workshop).
Fitting
  a   battery   not   listed   by   CITROËN would  
i

ntroduces   the   risk   of   faults   with   the   system.
Before
  doing   any   work   under   the  
b

onnet, deactivate the Stop & Start
system   to   avoid   the   risk   of   injury   related  
t

o   an   automatic   change   to   START  
m

ode.
The   Stop   &   Start   system   makes   use   of  
a

n   advanced   technology.   All   work   on  
t

his   type   of   battery   must   only   be   carried  
o

ut   by   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
t

he
 
vehicle
 
may
 
stall.
 
All
 
of
 
the
 
i

nstrument
 
panel
 
warning
 
lamps
 
come
 
o

n.
Depending
 
on
 
version,
 
an
 
alert
 
m

essage
 
may
 
also
 
be
 
displayed
 
asking
 
y

ou
 
to
 
put
 
the
 
gear
 
lever
 
into
 
position
 
N
and
 
put
 
your
 
foot
 
on
 
the
 
brake
 
pedal.
It is then necessary to switch off the
ignition,
 
then
 
restart
 
the
 
engine
 
using
 
t

he
 
key
 
or
 
the
 
"START/STOP"
 
button.
Reactivation
The system is reactivated automatically a t   every   new   start   using   the   key   or   the  
"

START/STOP"   button.
Press the "ECO OFF"
  switch   again.
The
 
system   is   active   again;   this   is   confirmed  
b

y
 
the
  switch   warning   lamp   going   off   and   the  
d

isplay   of   a   message.
Driving

193
C4-2_en_Chap06_conduite_ed02-2015
The flashing and then fixed illumination   of   the   under-inflation w

arning   lamp   accompanied   by   the
 i

llumination   of   the   service   warning
 l

amp   indicates   a   fault   with   the   system.
Operating fault
The alert is given by the fixed illumination   of   this   warning   lamp,  
a

ccompanied   by   an   audible   signal,  
a

nd   depending   on   equipment,   the  
d

isplay   of   a   message.
Under-inflation alert
In the event of a problem on one of the tyres, the   symbol   or   the   message   appears,   according  
t

o   equipment,   to   identify   it.
F
 
R
educe   speed,   avoid   sudden   steering  
m

ovements   or   harsh   brake   applications.
F
 
S
top   as   soon   as   it   is   safe   to   do   so. In
  this   case,   monitoring   of   the   tyre   pressures   is  
n

ot   assured.
F  
I
f   you   have   a   compressor   (the   one   in   the  
t

emporary   puncture   repair   kit   for   example),  
c

heck   the   four   tyre   pressures   when   cold.
 I

f   it   is   not   possible   to   check   the   tyre  
p

ressures   at   the   time,   drive   carefully   at  
r

educed
 s
peed.


or
F
I
n the event of a puncture, use the
temporary   puncture   repair   kit   or   the   spare  
w

heel   (according   to   equipment).
Go   to   a   CITROËN   dealer   or   a   qualified  w
orkshop to   have   the   system   checked   or,  
f

ollowing   the   repair   of   a   puncture,   to   have   the  
o

riginal   wheel,   equipped   with   a   sensor,   refitted.
Any
  tyre   repair   or   replacement   on   a   wheel  
f

itted   with   this   system   must   be   carried   out   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
If
  after   changing   a   tyre,   a   wheel   is   not   detected  
b

y   your   vehicle   (fitting   snow   tyres   for   example),  
y

ou   must   have   the   system   reinitialised   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
The loss of pressure detected does not
always
  lead   to   visible   deformation   of  
t

he   tyre.
Do
  not   rely   on   just   a   visual   check.This alert is also displayed when one or
more
  wheels   is   not   fitted   with   a   sensor  
(

for   example,   a   space-saver   or   steel  
spar

e
 w
heel).
The   alert   is   maintained   until   the   tyre   or  t
yres concerned is reinflated, repaired
or   replaced.
The
  spare   wheel   (space-saver   type   or   a  
s

teel   rim)   does   not   have   a   sensor.
6
Driving

198
C4-2_en_Chap06_conduite_ed02-2015
6. Speed  limiter   on   /   pause   indication.
7. S peed   limiter   mode   selection   indication.
8.
 P

rogrammed   speed   value.
9.
 S

election   of   a   memorised   speed   setting.
Displays in the instrument panel
Speed limiter
1. Speed  limiter   mode   selection   wheel.
2. P rogrammed   value   decrease   button.
3.
 P

rogrammed   value   increase   button.
4.
 S

peed   limiter   on   /   pause   button.
5.
 D

isplay   memorised   speed   settings   button.
Steering mounted controls
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter is switched on manually.
The   minimum   programmed   speed   is 2

0 mph   (30   km/h).
The
  programmed   speed   remains   in   the
 s

ystem   memory   when   the   ignition   is
 s

witched   off.
The speed limiter is a driving aid that cannot,   in   any   circumstances,   replace   the n

eed   to   observe   speed   limits   or   the   need
 f

or   vigilance   on   the   part   of   the   driver.
Driving

199
C4-2_en_Chap06_conduite_ed02-2015
Switching on
F If  the   speed   setting   is   suitable   (last   speed  s
etting   programmed   in   the   system)   press  
b

utton 4   to   switch   the   speed   limiter   on.
F

T
urn the wheel 1 to the "LIMIT"
position
to   select   the   speed   limiter;   the   function   is  
pa

used.
F  
P
ressing   button   4   temporarily   interrupts   the  
f

unction
 (
pause).
Adjusting the limit speed
setting
You do not have to switch the speed limiter on in   order   to   set   the   speed. To
  modify   the   limit   speed   setting   from   the  
c

urrent   speed   of   the   vehicle:
F
 
i
n   steps   of   +/-   1   mph   (km/h),   make  
s

uccessive short presses on button 2 or 3,
F
 
c
ontinuously,   in   steps   of   +/-   5   mph   (km/h),  
p

ress and hold button 2 or 3.
To
  modify   the   limit   speed   setting   using  
m

emorised   speeds   and   from   the   touch   screen  
t

ablet:
F

p
ress button 5   to   display   the   six   memorised  
s

peed
 se
ttings,
F

p
ress the button for the desired speed
setting.
This
  setting   becomes   the   new   limit   speed.
To
  modify   the   limit   speed   setting   using  
m

emorised  
s
peeds  
a
nd  
f
rom  
y
our  
A
udio  
s
ystem  
(

only   with   the   monochrome   screen   C):
F
 
w
ith   the   system   first   activated.
For
  more   information   on   memorising   speeds,  
r

efer   to   the   corresponding   section.
F
 
m
ake   a   long   press   on   button   2 or 3, the
system
  displays   the   memorised   speed  
c

losest   to   the   actual   speed   of   the   vehicle;  
t

his   setting   becomes   the   new   limit   speed.
F
 
t
o   choose   another   memorised   speed,   make  
a

nother   long   press   on   button   2 or 3.
6
Driving