remote control CITROEN C4 PICASSO 2010 User Guide
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2010, Model line: C4 PICASSO, Model: CITROEN C4 PICASSO 2010Pages: 352, PDF Size: 10.66 MB
Page 87 of 352
Downloaded from www.Manualslib.com manuals search engine IV
85
ACCESS
Locking the vehicle with
exterior perimeter monitoring
only
Deactivate the interior volumetric
monitoring to avoid unwanted trig-
gering of the alarm in certain cases
such as:
- leaving a pet in the vehicle,
- leaving a window partially open,
- washing your vehicle,
To be effective, this deactivation
must be carried out each time the
ignition is switched off.
Deactivation of the interior
volumetric monitoring
)
Switch off the ignition.
)
Within ten seconds, press the
button until the indicator lamp is
on continuously.
)
Get out of the vehicle.
)
Press the locking button on the
remote control immediately.
The exterior perimeter monitoring
alone is activated: the indicator lamp in
the button fl ashes once per second.
Triggering of the alarm
The monitoring functions remain
active until the alarm has been trig-
gered eleven times in succession.
When the vehicle is unlocked using
the remote control, rapid fl ashing
of the indicator lamp in the button
informs you that the alarm was trig-
gered during your absence. When
the ignition is switched on, this
fl ashing stops immediately.
Failure of the remote control
To deactivate the monitoring func-
tions:
Locking the vehicle without
activating the alarm
Malfunction
Automatic activation *
)
Lock or deadlock the vehicle us-
ing the key in the driver's door
lock.
When the ignition is switched on, fi xed il-
lumination of the indicator lamp in the but-
ton indicates a malfunction of the system.
Have it checked by a CITROËN dealer or
a qualifi ed workshop.
2 minutes after the last door or the
boot is closed, the system is activat-
ed automatically.
)
To avoid triggering the alarm on
entering the vehicle, fi rst press
the unlocking button on the re-
mote control.
)
Unlock the vehicle using the key
in the driver's door lock.
)
Open the door; the alarm is trig-
gered.
)
Switch on the ignition; the alarm
stops. The indicator lamp in the
button goes off.
This is indicated by sounding of the
siren and fl ashing of the direction in-
dicators for thirty seconds.
Reactivation of the interior
volumetric monitoring
)
Press the unlocking button on the
remote control to deactivate the
exterior perimeter monitoring.
)
Press the locking button on the
remote control to activate all the
monitoring functions.
The indicator lamp in the button
again fl ashes once per second.
*
According to country.
Page 90 of 352
Downloaded from www.Manualslib.com manuals search engine IV
88
ACCESS
DOORS
Opening
From outside
When the selective unlocking is
activated, the fi rst press of the
remote control unlocking button
permits unlocking of the driver's
door only.
)
Pull the interior control lever of
a front door; this unlocks the ve-
hicle completely.
With the selective unlocking acti-
vated:
- the driver's door control unlocks
the driver's door only,
- the other door controls unlock
the other doors and the boot.
The interior door controls do not
operate when the vehicle is dead-
locked.
Manual central locking
control
System for locking or unlocking the
vehicle - the doors and boot - from
the driving position.
Locking
)
Press this button to lock the ve-
hicle.
The red indicator lamp on the button
comes on.
If one of the doors is open, the cen-
tral locking does not take place.
If the boot or the rear screen is
open, central locking from the in-
side is active for the doors, to allow
long objects to be carried.
)
After unlocking the vehicle com-
pletely using the remote control
or the key, pull the door handle.
From inside
Page 91 of 352
Downloaded from www.Manualslib.com manuals search engine IV
89
ACCESS
Unlocking
)
Press this button again to unlock
the vehicle.
The red indicator lamp on the button
goes off.
If the vehicle is locked or dead-
locked from the outside, the red in-
dicator lamp fl ashes and button A
is inactive.
)
In this case, use the remote
control or the key to unlock the
vehicle.
Automatic central locking
This system automatically locks the
doors, boot and rear screen while
driving.
You can activate or deactivate this
function.
Locking
When the speed exceeds 6 mph
(10 km/h), the doors, the boot and
the rear screen lock automatically.
Unlocking
)
Above 6 mph (10 km/h), press
this button to unlock the doors,
the boot and the rear screen
temporarily.
Ignition on:
Deactivation
)
Press this button again for more
than two seconds.
A confi rmation message appears in
the multifunction screen.
Emergency control
System which locks or unlocks the
doors mechanically in the event of
a malfunction of the battery or of the
central locking.
Locking the driver's door
)
Insert the key in the lock, then
turn it to the right.
Unlocking the driver's door
)
Insert the key in the lock, then
turn it to the left.
Locking the front and rear
passenger doors
)
Insert the key in the lock, located
on the edge of the door, then turn
it one eighth of a turn
.
Unlocking the front and rear
passenger doors
)
Pull the interior door opening
control.
If one of the doors or the boot or
rear screen is open, the automat-
ic central locking does not take
place. Activation
)
Press this button for more than
two seconds.
A confi rmation message appears in
the multifunction screen. In the event of a fault with the cen-
tral locking, you must disconnect
the battery to lock the boot and so
ensure the complete locking of the
vehicle.
Page 92 of 352
Downloaded from www.Manualslib.com manuals search engine IV
90
ACCESS
BOOT
)
After unlocking the vehicle com-
pletely using the remote control
or the key, with the rear screen
closed, pull on the lever 1
and
raise the tailgate.
)
Lower the tailgate using one of
the two handholds 3
, located on
the interior trim.
- when the engine is
running
, this warning
lamp comes on, accom-
panied by a message in
the multifunction screen
for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
this warning lamp comes on, ac-
companied by an audible signal
and a message in the multifunc-
tion screen for a few seconds.
If the tailgate is not closed correctly:
REAR SCREEN
This opening gives easy access
to the boot, even if you are parked
close to a wall or another vehicle.
Closing
)
Lower the rear screen guiding
it with the wiper arm until it is
closed.
If the rear screen is not closed cor-
rectly:
- when the engine is
running
, this warning
lamp comes on, accom-
panied by a message in
the multifunction screen
for a few seconds,
- when the vehicle is moving
(speed above 6 mph (10 km/h)),
this warning lamp comes on, ac-
companied by an audible signal
and a message in the multifunc-
tion screen for a few seconds.
The boot and the rear screen
cannot both be open at the same
time. When the rear screen is open,
you can access the boot by rais-
ing the rear shelf using its tab
(C4 Picasso).
)
After unlocking the vehicle com-
pletely using the remote control
or the key, with the boot closed,
press the control 2
and raise the
rear screen using the base 4
of
the wiper arm.
)
Past the balancing point, allow
the tailgate to lower and close
itself (do not assist it or slow it
down).
Opening
Opening
Closing
Page 93 of 352
Downloaded from www.Manualslib.com manuals search engine IV
91
ACCESS
Emergency boot release
System for mechanical unlocking of
the boot in the event of a battery or
central locking malfunction.
Unlocking
)
Fold back the rear seats to gain
access to the lock from inside
the boot.
)
Insert a small screwdriver into
hole A
of the lock to unlock the
tailgate.
)
Push the white part, located in-
side the lock, to the left to unlock
the boot.
PANORAMIC SUNROOF
It is fi tted with an electrically con-
trolled blind.
Opening the roof blind
)
Rotate the control knob B
to slide
the roof blind to the desired posi-
tion (positions 1
to 9
).
Closing the roof blind
)
Rotate the control knob B
to po-
sition 0
to close the roof blind.
Recommendations
- Pressing the locking button on
the remote control for more than
two seconds will close the blind
(practical when, for example,
you leave your vehicle in a sunlit
car park).
- On returning to your vehicle, a
press on control knob B
reposi-
tions the blind to the last position
selected.
Anti-pinch
The blind has an anti-pinch func-
tion.
At the end of its travel, when the blind
encounters an obstacle on closing, it
stops and moves back slightly.
Following a fault or after a battery
disconnection during the movement
of the blind or after it has stopped,
you must re-initialise the anti-pinch
function:
)
place the blind in the closed po-
sition,
)
press control knob B
for approxi-
mately two seconds.
Page 98 of 352
Downloaded from www.Manualslib.com manuals search engine V
96
VISIBILITY
Daytime running lamps
Daytime lighting, compulsory in cer-
tain countries, which comes on auto-
matically when the engine is started
making the vehicle more visible to
other users.
Manual guide-me-home
lighting
The temporary lighting of dipped
headlamps after the vehicle's igni-
tion has been switched off makes
the driver's exit easier when the light
is poor.
Switching on
)
With the ignition off, "fl ash" the
headlamps using the lighting
stalk B
.
)
A second "headlamp fl ash"
switches the function off again.
Switching off
The manual guide-me-home lighting
switches off automatically after a set
time.
The manual guide-me-home light-
ing is also available by pressing the
lighting button on the remote con-
trol (refer to the section "Access -
§ Remote control key").
This function is assured:
- in countries where it is imposed
by regulations,
by illumination of the dipped
beam headlamps with the side-
lamps and number plate lamps.
- for other countries where it is
provided,
by the use of dedicated LED lamps.
The instruments and controls (mul-
tifunction screen, air conditioning
control panel, ...) are not illuminated,
except in night mode with manual or
automatic illumination of headlamps.
LED lamps
They come on when the engine is
started.
Depending on the destination country,
they are used for:
- daytime running lamps in day mode
and sidelamps in night mode,
or
- sidelamps in day and night mode
Where LED lamps are fi tted, the fi la-
ment bulbs for the sidelamps in the
front lamp units are not used.
Activation or deactivation of this
lighting is done via the vehicle con-
fi guration menu. This function can be activated or
deactivated via the vehicle confi gu-
ration menu.
Page 100 of 352
Downloaded from www.Manualslib.com manuals search engine V
98
VISIBILITY
OF XENON HEADLAMPS
This system adjusts the height of the
xenon headlamp beams automati-
cally and when stationary, according
to the load in the vehicle, so as to
avoid causing a nuisance to other
road user.
If a malfunction occurs,
this warning lamp is dis-
played in the instrument
panel, accompanied by
an audible signal and a message in
the screen.
The system then places your head-
lamps in the lowest position.
Do not touch the xenon bulbs.
Contact a CITROËN dealer or a
qualifi ed workshop.
MANUAL ADJUSTMENT OFHEADLAMPS
To avoid dazzling other road users,
the height of the halogen bulb head-
lamps must be adjusted according
to the load in the vehicle. To do this,
turn the control, located below the
dashboard to the left of the driver, to
the appropriate position:
0.
1 or 2 people in the front seats.
-.
3 people.
1.
4 to 7 people.
-.
Intermediate setting.
2.
4 to 7 people + maximum autho-
rised loads.
-.
Intermediate setting.
3.
Driver + maximum authorised loads.
Initial setting is position " 0
".
EXTERIOR SIDE SPOTLAMPS
Switching on
The side spotlamps come on tempo-
rarily:
- when you unlock the vehicle,
- when you press the lighting button
on the remote control,
-
with the automatic guide-me-home
lighting, on switching off the ignition,
- when you remove the key from
the ignition,
- when you open a door,
- when you use the remote control
to locate the vehicle.
Page 105 of 352
Downloaded from www.Manualslib.com manuals search engine V
103
VISIBILITY
COURTESY LAMPS
1.
Front courtesy lamp
2.
Map reading lamps
Front courtesy lamp
In this position, the courtesy
lamp comes on gradually: Permanently off.
Permanent lighting.
In permanent lighting mode, different
lighting times are available:
- with the ignition off, approxi-
mately ten minutes,
-
in energy economy mode, approxi-mately thirty seconds,
-
with the engine running, unlimited.
- when the vehicle is unlocked,
- when a door or the boot is
opened,
- when the key is removed from
the ignition,
-
when the remote control locking
button is activated, in order to locate
your vehicle.
It switches off gradually:
- when the vehicle is locked,
- when the ignition is switched on,
- 30 seconds after the last door is
closed.
Map reading lamps
)
With the ignition on, press the
corresponding switch.
Panoramic sunroof courtesy
lamps
These courtesy lamps have two oper-
ating modes:
- automatic lighting when a door is
opened or when the front cour-
tesy lamp is in the "permanent
lighting" position,
- permanent lighting.
Opening the boot switches on the
third row courtesy lamp and the
boot lamps.
Page 106 of 352
Downloaded from www.Manualslib.com manuals search engine V
104
VISIBILITY
LIGHTING PACK
Interior mood lighting
This function activates the light sources
which are located in the dashboard, near
the interior door levers and in the roof.
Operation
This back-lit control, located near
the steering wheel below the dash-
board, is used to switch on and off
and adjust the brightness of this
lighting.
To increase
brightness:
)
Press the right of the control to
obtain the desired level.
To reduce
brightness:
)
Press the left of the control to obtain
the desired level.
The setting is stored when the ignition
is switched off.
Interior welcome lighting
When unlocking the vehicle with the
remote control or the key, the foot-
well lamps, interior lamps and interior
mood lighting sources come on for
30 seconds.
This function cannot be deactivated.
Front door pockets with
automatic lighting
The lighting for the door pockets
comes on automatically when you
place a hand inside one of the com-
partments.
It goes off after a few seconds when
you take your hand away.
Reading lamps on front seat
backrests
There are reading lamps in the back-
rests of the front seats, behind the
rear tables. They can operate only
when the table is lowered.
)
Press the "On/Off" button to switch
the reading lamp on or off. This lighting, available once the
sidelamps are on, in night mode,
provides subdued lighting in the
passenger compartment.
Page 127 of 352
Downloaded from www.Manualslib.com manuals search engine VII
125
CHILD SAFETY
MANUAL CHILD LOCK
Locking
)
Using the ignition key, turn the
red control one eighth of a turn,
following the instructions on the
label.
Unlocking
)
Using the ignition key, turn the
red control one eighth of a turn
to return to the original position.
ELECTRIC CHILD LOCK
Mechanical system to prevent open-
ing of the rear door using its interior
control.
The control is located on the edge of
each rear door. Remote control system to prevent
opening of the rear doors using their
interior controls and use of the rear
electric windows.
Activation
)
Press button A
.
Deactivation
)
Press button A
again.
This system is independent of and
in no circumstances takes the place of the central locking system.
Check the status of the child
lock each time you switch on the
ignition.
Always remove the key from the
ignition when leaving the vehicle,
even for a short time.
In the event of a serious impact,
the electric child lock is deactivated automatically to permit the exit of
the rear passengers.
This warning lamp comes
on temporarily on the instru-
ment panel when the child
lock is activated.
It also comes on when the ignition is
switched on, then goes off approxi-
mately ten seconds after the engine
is started. The control is located on the driver's
door, with the electric window controls.