change Citroen C4 PICASSO 2013 1.G User Guide

152
Driving
Never select neutral Nwhen driving.
Automated mode
)Select position A.
AUTOor A
and the gear engaged is
displayed in the instrument panel.
The gearbox operates in auto-active mode,
without an
y action on the par t of the driver. Itcontinuously selects the most suitable gear for:
- optimisation of fuel consumption,
- the st
yle of driving,
- the profile of the road.
- t
he vehicle load.


For optimum acceleration, for examplewhen overtaking another vehicle, press the accelerator pedal firmly past the point of resistance.


Te m p o r a ry control of gear changing

You can temporarily take over control of gear changing using the "+"
and "-"steeringmounted paddles. If the engine speed allows,
the instruction to change gear is acted on.
This function allows you to anticipate cer tain
s
ituations such as overtaking a vehicle or the
approach to a corner.
After a few moments without any action on
the control paddles, the gearbox resumes
automatic control of the gears.

)Select position M.
The gears engaged are displayed in succession
in the instrument panel.
The
gear change requests are only acted on if
the engine speed permits.
It is not necessary to release the accelerator
durin
g gear changes.
When braking or slowing down, the gearboxchanges down automatically to allow the
vehicle to accelerate in the correct gear.
On sharp acceleration, the gearbox will notchange up unless the driver acts on thesteering mounted paddles.

Manual mode

You can change mode at any time by movingthe selector lever from A
to Mor the other way
round.

N
ever select neutral N
while the vehicle ismoving.

154
Driving








Automatic gearbox
This gearbox offers two driving modes.
- automatedmode for automatic management of the gears by the gearbox,
without any action on the par t of the driver,-manualmode for sequential gear changingby the driver using the steering mountedpaddles.
P
.Park.


- Immobilisation of the vehicle, parking brake
applied or released.

- Starting the engine.R.
Reverse.


- Reversing, vehicle stationary and engine at
i
dle.
N.Neutral.


- Immobilisation of the vehicle, parking brake
applied.

- Startin
g the engine.D.Automatic operation. M.Manual operation with sequential changingof the six gears.


Gear selector lever


To select position P
, move the gear Pselector to the highest position (towards R), then push it for wards and Rthen to the left. Only engage it when the vehicle is at acomplete stop. In this position, the frontwheels are locked. Ensure that the gear selector is correctly positioned.

To move the gear selector, switch onthe ignition or star t the engine.
If the battery is not sufficiently charged, it is not possible to move the gear selector.


To come out of position P
, move the Pgear selector to the right to the desired position, while keeping your foot on thebrake pedal.


It is possible to change from one modeto the other at any time.
With the automated mode, you cantemporarily take control of the gear changes at any time.

155
4
Driving
+.Control paddle for changing up, to the right
of the steering wheel. )Pull the " +" paddle towards you to change
up.-. Control paddle for changing down, to the
left of the steering wheel. )Pull the "- " paddle towards you to changedown.


Steering mounted control paddles


The steering mounted control paddlescannot be used to select neutral or toselect or come out of reverse.
When
you move the gear selector, the symbol corresponding to its position is displayed in the instrument panel. P.Park. R. Reverse.
N.Neutral.D. Drive (automatic forward drive).
1 to 6.Gears engaged in manual operation.-.Invalid value in manual operation.
Displays in the instrument panel
Moving off
)
With your foot on the brake pedal, selectposition Por N.
)
Start the engine.
IfPis displayed in the instrument panel,although the gear selector is in another position, place the gear selector inposition Pto be able to star t the engine.
)
With the engine running, press the brake pedal. )
Select automated mode (position D),manual mode (position M) or reverse (position R
). R
If you do not press thebrake pedal to come out of position P, this warning lamp P


Other wise, there is an audible signalaccompanied by a message.
or symbol appears in the instrument panel, accompanied by the message"Place automatic gearbox in position P",
flashing of P
in the instrument paneland an audible signal.

157
4
Driving
Invalid value in manual operation
This symbol is displayed i
f a gear is not engaged correctly (gear selector
between two positions). You can temporaril
y take control of gear changes using the "+
" and "-" steering mounted control paddles. If the engine speed allows, the
instruction to change gear is acted on.
This function allows you to anticipate cer tain situations such as overtaking another vehicle or
approaching a bend.
After a few moments with no action on the control paddles, the gearbox manages thegears automatically again.

Te m p o r a ry manual control of the gears


Manual mode
Dand the gear engaged are displayed in the instrument panel.
The gearbox operates in auto-active
mode, without any action from the driver. It continuously selects the most appropriate gear
according to the following conditions:


- optimisation of fuel consumption,

- drivin
g style,

- relief of the road,

- vehicle load.


Automated mode
)
Select position D.

For maximum acceleration, without touching
the gear selector, press the accelerator fully
down (kick down). The gearbox changes down
automatically and maintains the gear selected
until the maximum en
gine speed is reached.
When braking, the gearbox changes down
automatically for more effective engine braking.
When you take your foot of the accelerator pedal suddenly, the gearbox does not change
up, so as to improve safety.
) Select position M.)
Use the " + " and "- " steering mounted
control paddles to change gear.
The gears engaged are displayed successively
in the instrument panel.
When stationar
y or at very low speed, the gearbox automatically engages 1st
gear.
In manual mode, it is not necessary to release
the accelerator pedal when changing gear.
The change from one gear to another is onlyeffected if the conditions of vehicle speed andengine speed allow; other wise the automatic
laws of operation are imposed temporarily.
If the engine speed is too high or too low,
the display of the gear selected flashes for a few seconds, then the new gear engaged is displayed.
It is possible to change mode at any time, by moving the gear selector from D
to Mor the other way round.

158
Driving
Before switching off the engine, you canchange to position P or Nto be in neutral.
In either case, appl
y the parking brake to
immobilise the vehicle, unless it is programmed
in automatic mode.
If the lever is not in position P, on opening the Pdriver's door or approximately 45 seconds after switching off the ignition there is an audible signal and a message appears: )move the gear selector to position P; the audible signal stops and the message
disappears.

Operating fault
Whenever parking, you must apply the parking
brake to immobilise the vehicle, if automatic
operation has been deactivated.
Parking the vehicle

In all circumstances, ensure that thegear selector is in position Pbefore leaving your vehicle.In th
e event of a fault with the
gearbox, the ser vice warning lamp
comes on in the instrument panel, accompanied by a message and anaudible signal.

In this case the gearbox goes into back-up
mode and stays in 3rdgear. You may then feel
a noticeable jolt when going from P to Rand from N
to R
. This jolt does not present any risk
to the gearbox.
Do not exceed 60 mph (10 0 km/h) while also
observing legal speed limits.
Have it checked by a CITROËN dealer or aqualified workshop.

159
4
Driving

Operation









Gear shift indicator

System which reduces fuel consumption by advising the driver to change up.
With an electronic gearbox, the system is only active in Manual mode.


The system adapts its gear change recommendation according to thedriving conditions (slope, load, ...) and the demands of the driver (power,acceleration, braking, ...).
The system never suggests:


- engaging first gear,

- engaging reverse gear,

- engaging a lower gear.
Example:
- You are in third gear.
- Yo u press the accelerator pedal.
- The s
ystem may suggest that you engage a
higher gear.
The in
formation appears in the instrumentpanel in the form of an arrow. On vehicles with manual gearbox, the arrowcan be accompanied by the recommended gear.
Depending on the driving situation and your
vehicle's equipment, the system may advise
you to skip one (or more) gear(s). You can
follow this instruction without engaging the
intermediate gears.
The gear engagement recommendations mustnot be considered compulsory. In fact, the configuration of the road, the amount of traffic
and safety remain determining factors whenchoosing the best gear. Therefore, the driver
remains responsible for deciding whether or not
to follow the advice given by the system.
This function cannot be deactivated.

173
4
Driving
Flashing of the dashes indicates a fault with thecruise control.
Have it checked by a CITROËN dealer or aqualified workshop.
Operating fault

Exceeding the programmed
speed
If the programmed speed is exceeded, the
displayed speed flashes.
Once the vehicle returns to the programmedspeed, the display becomes steady again.

Switching off
)Turn wheel 1
to the "0"position.
The display of information related to the cruise control disappears.



When the cruise control is switched on,be careful if you maintain the pressure on one of the programmed speedchanging buttons: this may result in avery rapid change in the speed of your vehicle.
Do not use the cruise control on slippery roads or in heavy traffic. On a steep descent, the cruise control will not be able to prevent the vehicle from exceeding the programmed speed. On steep climbs or when towing, the programmed speed may not be reachedor maintained.
The use of mats not approved byCITROËN may inter fere with the
operation of the cruise control.
To avoid any risk of jamming of the pedals:


- ensure that the mat is positioned correctly,

- never fit one mat on top of another.

174
Driving





Active cruise control
This systems allows, in addition to maintainingyour vehicle's speed at a value that you have defined, the inter-vehicle time you have
selected between your vehicle the the one ahead to be maintained (2 seconds by default,
on activating the function).

Principles of operation

Using a radar with a range of about 100 metres,located at the front of the vehicle, this system
detects a vehicle running in front of your
vehicle.
It automatically adapts the speed of the vehicle
to that of the vehicle in front.
If the vehicle in front is running more slowly,
the system progressively reduces the speed of your vehicle using just engine braking (as if thedriver had pressed the "- " button).
If your vehicle is too close to or approaching tooquickly the vehicle in front, the cruise control
is automatically deactivated. The driver is then
aler ted by an audible signal, accompanied by a message.
If the vehicle in front accelerates or changeslane, the active cruise control progressively
accelerates your vehicle to return to the
programmed speed.
If the driver operates a direction indicator to
the left (left hand drive) or the right (right hand
drive), to over take a slower vehicle, the active cruise control allows your vehicle to temporarily
approach the vehicle in front to assist the
over takin
g manoeuvre, though never exceeding
the programmed speed.

The active cruise control operates byday and at night, in fog or in moderate rainfall.


The system does not act on the brakingsystem, but works only with engine braking.
The regulation range is limited: there willno longer be any adjustment of speed if the difference between the programmed speedsetting and the speed of the vehicle in front becomes too high (18 mph (30 km/h).


The activation of this system deactivates the function of inter-vehicle time.


If the difference between the programmed speed setting and the speed of the vehicle in front is toogreat, the speed cannot be adjusted: the cruise control is automatically
deactivated.

179
4
Driving
not possible, conditions unsuitable" is displayed while reactivation is not possible. When the conditions allow, it is recommended that the function be reactivated by pressing button 2or 3,
which will make the current speed of your vehicle the new cruise speed setting, rather than by pressing button 4(on/pause) which reactivates the cruise control using the old cruise speed setting, which may be very different from the current speed of your vehicle.

SymbolDisplay in theinstrument panelAssociated messageComments
"
SPEED ADJUSTED" Detection of a vehicle that is too close or running at a speed lower than your
vehicle's cruise speed setting.
The system uses engine braking to slow your vehicle and then hold it at the speed of
the vehicle in front so as to maintain the programmed inter-vehicle time.
The regulation range is limited to a maximum difference of 20 mph (30 km/h)between the speed setting and the speed of the vehicle ahead.
"
Cruise control paused". If the system exceeds the limit of speed adjustment possible by the system and in
the absence of any reaction by the driver (operation of the direction indicator, change
of lane, reduction of the speed of the vehicle), the system is automatically paused.
The display of the deactivation message is accompanied by an audible signal.

181
4
Driving
In the event of a fault with the active cruisecontrol, you are alerted by an audible signal
and display of the message message "Drivingaid functions fault".
Have the system checked by a CITROËN
dealer or a qualified workshop.
When the cruise control is working, takecare if making a maintained press onone of the cruise control programmedspeed modification buttons: this can lead to a very quick change in thespeed of your vehicle. Do not use the active cruise control onslippery surfaces or in heavy traffic. When descending a steep hill, thecruise control may not be able to prevent the vehicle from exceeding theprogrammed speed.When ascending a steep hill or whentowing, it might not be possible to attainor maintain the programmed speed. The use of mats not approved by CITROËN may inter fere with the
operation of the cruise control. To avoid any risk of jamming the pedals:- ensure that mats are positioned correctly, - never fit one mat on top of another.


Operating fault


The operation of the radar, located in the front bumper, may be disturbed by accumulations of grime (dust, mud...) or in certain weather conditions (snow,ice...).
The message "SYSTEM INACTIVE:Visibility reduced" is displayed to signal that the system has been put intostandby.
Clean the front bumper regularly.