air condition Citroen C5 2000 (DC/DE) / 1.G Owner's Manual

Downloaded from www.Manualslib.com manuals search engine PRESENTATION
THIS HANDBOOK summarises the specifications, adjustments, checks and special features of theCITROEN C5.
The handbook is divided into the following sections representing the main functions :
GENERAL - ENGINE - INJECTION - IGNITION - CLUTCH - GEARBOX - DRIVESHAFTS - AXLES - SUSPENSION - STEERING - BRAKES - HYDRAULICS -
ELECTRICAL - AIR CONDITIONING.

Downloaded from www.Manualslib.com manuals search engine INJECTION
Idling - antipollution 111
Petrol injection 112
Emission standards 113 - 119
Prohibited operations : HDi 120 - 121
Safety requirements : HDi 122 - 123
Checking the fuel supply circuit 124 - 125
Checking the air supply circuit 126 - 130
Exhaust gas recycling 131 - 134
Checking turbo pressure 135 - 138
Features of injection systems 139 - 168
IGNITION
Sparking plugs 169
CLUTCH-GEARBOX
Speedometers 170
Clutch specifications 171 - 172
Gearbox and tyre specifications 173 - 174
BE4/5 gearbox controls 175 - 183
ML/5 gearbox controls 184 - 192
AL4-4HP20 gearbox controls 193 - 203
Driveshafts 204
AXLES-SUSPENSION
Wheels and tyres 205 - 211
Axle geometry 212 - 214
Front and rear axle 215 - 216Suspension 217 - 220
Steering specifications 221 - 222
BRAKES
Brake specifications 223 - 228
Handbrake adjustment 229
Bleeding and filling braking system 230 - 233
HYDRAULICS
Specifications 234 - 237
Suspension spheres 238 - 240
ELECTRICAL
Starter motors 241
Alternators 242
Charging circuit 243
AIR CONDITIONING
Quantities in R 134a aircon system 244
Special features 245
Pollen filter 246
Dryer cartridge 247 - 249
Checking oil level 250 - 251
Checking pressures 252
Air conditioning : 6FN-RFN-RLZ 253
Air conditioning circuit : XFX 254
Air conditioning circuit : RHY-RHZ 255
Air conditioning circuit : 4HX 256
INDEX
GENERAL
Identification of vehicles 1 - 4
General : Dimensions 5 - 6
Weight specifications 7 - 8
Towing specifications 9 - 10
Lifting / supporting the vehicle 11 - 14
Capacities 15 - 18
Lubricants 19 - 32
ENGINES
Engine specifications 34 - 58
Cylinder head marking / tightening
6FZ-RFN-RLZ 38
XFX 51 - 52
RHY-RLZ 55 - 56
4HX 57 - 58
Auxiliaries drive belt 59 - 68
Checking and setting valve timing 69 - 90
Power unit suspension 91 - 95
Exhaust system 96 - 100
Cooling system 101 - 107
Checking oil pressures 108
Oil filter 109
Filling and bleeding engine coolant 110

Downloaded from www.Manualslib.com manuals search engine GENERAL
Engine type
Engine with filter change
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
6FZ RFN RLZ RHY RHZ
4.25 4.75
1.7 1.5
1.8 1.8 1.8 1.8
6 6 8.3
3 3 5.3
4.3
8.8 – 9.3 (*) 8.8 10.7
66 68
16
CAPACITIES (in litres)
1.8i 16V 2.0i 16V 2.0 HPi 2.0 HDiPetrol
Diesel
Vehicle without air conditioning
(*) = With automatic gearbox
ESSENTIAL : Systematically check the oil level using the oil dipstick.
Auto.Auto.Auto.

Downloaded from www.Manualslib.com manuals search engine GENERAL
17
Engine type
Engine with filter change
Between Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
CAPACITIES (in litres)
Petrol
Vehicle with air conditioning
(*) = With automatic gearbox.
ESSENTIAL : Systematically check the oil level using the oil dipstick.
1.8i 16V 2.0i 16V 3.0i V6
Auto.Auto.Auto.
6FZ RFN RLZ XFX
4.25 5.25
1.7 2
1.8 1.8 1.8
6 6 8.3
3 3 5.3
4.3
8.8 – 9.3 (*) 8.8 14
662.0 HPi

Downloaded from www.Manualslib.com manuals search engine 18
GENERAL
Engine type
Engine with filter change
EBetween Min. and Max.
5-speed gearbox
Automatic gearbox
After oil change
Braking circuit
Hydraulic circuit
Cooling system
Fuel tank capacity
CAPACITIES (in litres)
Diesel
Vehicle with air conditioning
ESSENTIAL : Systematically check the oil level using the oil dipstick
RHY RHZ 4HX
4.5 4.75
1.7 1.5
1.8 1.8
6 8.3
3 5.3
4.3
10.7 - 11.7 - (With additional heating).
68 2.0 HDi 2.2 HDi
Auto.
Auto.

Downloaded from www.Manualslib.com manuals search engine 33
GENERAL
ENGINE OIL CONSUMPTION
I-Oil consumption depends on :
- the engine type.
- how run-in or worn it is.
- the type of oil used.
- the driving conditions.
II -An engine can be considered RUN-INafter:
- 3,000 miles(5,000 km) for aPETROLengine.
- 6,000 miles (10,000 km) for a DIESELengine.
III - MAXIMUM PERMISSIBLEoil consumption for a RUN-INengine.
- 0.5 litres per600 miles (1,000 km) for a PETROL engine.
- 1 litre per 600 miles(1,000 km) for a DIESEL engine.
DO NOT WORK BELOW THESE VALUES.
IV - OIL LEVEL :The level shouldNEVER be above theMAX. mark on the dipstick after changing or topping up the oil.
- This excess oil will be used up rapidly.
- It will reduce the engine output and adversely affect the operation of the air circuits and gas recycling.

Downloaded from www.Manualslib.com manuals search engine ENGINE
63
AUXILIARY EQUIPMENT DRIVE BELT
Engines : RHY - RHZ
Without air conditioning
B1BP1YKD
TOOLS
[1]Belt tension adjusting square: (-).0188 J2
[2] Ø 4 mm peg: (-).0188.Q1
[3] Ø 2 mmpeg: (-).0188.Q2.
[4] Dynamic tensioner compression lever: (-).0188.Z
Remove
Re-use of belt
WARNING : Mark the direction the belt was fitted in case of re-use of the same belt.
- Compress the tensioner roller (2) by action at «a»(in anti-clockwise direction), tool [4].
- Keep the tensioner roller(2)compressed and remove the belt.
No re-use of belt.
- Compress the dynamic tensioner roller (2) by action at «a»(anti-clockwise), using tool [4].
- Peg using tool [2], at «b».
- Hold the dynamic tensioner roller (2)compressed and remove the belt.
- Loosen the screw (1).

Downloaded from www.Manualslib.com manuals search engine ENGINE
64
AUXILIARY EQUIPMENT DRIVE BELT
Engines : RHY - RHZ
Without air conditioning (continued)
Refit.
Re-used belt.
- Compress the tensioner roller(2)by action at «a»(anti-clockwise), tool [4].
- Refit the belt.
WARNING : Respect the direction in which the belt is fitted.
- Remove the tool [4].
New belt.
- Refit the belt.
- Turn the eccentric roller (3), tool[1] (clockwise)to free the tool [2]from its pegging at «b».
- Hold the eccentric roller (3), tool [1], and tighten the screw(1) to 4.3 ± 0.4 m.daN.
- Remove the tool [2].
- Rotate the crankshaft 4 times in the direction of rotation.
- Check that it is possible to peg at «b», tool [3].
- If not possible to peg, restart the adjustment.
B1BP1YMD

Downloaded from www.Manualslib.com manuals search engine ENGINE
65
AUXILIARY EQUIPMENT DRIVE BELT
Engines : RHY - RHZ
With air conditioning
B1BP1YLD
TOOLS
[1] Belt tension adjusting square : (-).0188 J2
[2] Ø 4 mm peg :(-).0188.Q1
[3] Ø 2 mm peg :(-).0188.Q2
[4] Dynamic tensioner compression lever :(-).0188.Z
Remove
Re-use of belt
WARNING : Mark the direction the belt was fitted in case of re-use of the same belt.
- Compress the tensioner roller (7) by moving it at «c»(in anti-clockwise direction), tool [4].
- Hold the tensioner roller(7) compressed and remove the belt.
No re-use of belt.
- Compress the tensioner roller (7)by moving it at «c»(in anti-clockwise direction), tool[4].
- Peg using tool [2], at «d».
- Loosen the screw (6).
- Bring the eccentric roller (5)towards the rear.
- Tighten the screw (6)by hand.
- Remove the belt.

Downloaded from www.Manualslib.com manuals search engine ENGINE
66
AUXILIARY EQUIPMENT DRIVE BELT
Engines : RHY - RHZ
With air conditioning (continued)
Refit.
Re-used belt.
- Compress the tensioner roller (7)by action at «c»(in anti-clockwise direction), tool [4].
- Refit the belt.
WARNING : Respect the direction in which the belt is fitted.
- Remove the tool [4].
New belt.
- Refit the belt.
- Turn the eccentric roller (5), tool [1](clockwise)to free the tool [2]from its pegging at «d».
- Hold the eccentric roller (5), tool [1], and tighten the screw (6)to 4.3 ± 0.5 m.daN.
- Remove the tool [2].
- Rotate the crankshaft 4 times in the normal direction of rotation.
- Check that it is possible to peg at «d», tool [3].
- If not possible to peg, restart the adjustment..
B1BP1YND