check engine Citroen C5 2008.5 (RD/TD) / 2.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2008.5, Model line: C5, Model: Citroen C5 2008.5 (RD/TD) / 2.GPages: 306, PDF Size: 18.9 MB
Page 13 of 306
31
1
I N S T R U M E N T S a n d C O N T R O L S
Engine autodiagnostics system If this comes on, it indicates
the occurrence of a fault in
the engine management
system.
I f i t fl a s h e s , i t i n d i c a t e s t h e o c c u r r e n c e o f
a fault in the emission control system.
Maximum coolant temperature If this comes on, it indicates
that the temperature in the
cooling system is too high.
Stop the vehicle immediately
and as safely as possible.
Check the coolant level.
If the level is low, contact a CITROËN
dealer.
Fuel low
If this comes on, it indicates
that the range remaining
i s a p p r o x i m a t e l y 3 0 m i l e s
(50 km).
It may be less than this in certain
driving conditions and depending on
the engine.
T h e c a p a c i t y o f t h e t a n k i s a p p r o x i -
mately 71 litres. Battery charge
If this comes on, it indi-
cates the occurrence of a
fault in the battery charging
circuit (dirty or loose termi-
nals, slack or cut alternator
belt...).
Seat belt not fastened/
unfastened *
* According to country.
This warning lamp lights
up on the instrument panel
to remind the driver and all
passengers that they must
fasten their seat belt.
It is linked to the seat belt informa-
tion given by the roof console. Seat belt non-fastening/
unfastening
This warning lamp
informs you of the
non-fastening and
unfastening of the
driver and passenger seat belts.
The illuminated positions represent
the passengers whose seat belts
are not fastened/unfastened.
Driver’s seat belt not fastened:
- The warning lamp lights up be- tween 0 and 12 mph (20 km/h).
A b o v e 1 2 m p h , i t fl a s h e s a c -
companied by a sound signal for
around 120 seconds.
Front and rear passenger seat belts
not fastened:
- When the ignition is switched on, the points corresponding to
the seat positions with seat belts
not fastened remain lit up for
30 seconds.
Seat belts unfastened during the
journey:
- The point corresponding to the seat position with seat belt un-
fastened lights up between 0 and
12 mph (20 km/h). Above
1 2 m p h , i t fl a s h e s a c c o m p a n i e d
by an audible signal for around
120 seconds. The audible signal
stops when the seat belt is re-
fastened or if a door is opened.
Page 15 of 306
33
1
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
Your CITROËN technician resets the
indicator to zero after each service.
However, if you do your own servi-
cing, the procedure for resetting to
zero is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of
the message "Oil level measure-
ment invalid". Consult a CITROËN
dealer.
Page 16 of 306
33
1
I N S T R U M E N T S a n d C O N T R O L S
Maintenance indicator zero reset
After each service, the maintenance
indicator must be reset to zero.
Your CITROËN technician resets the
indicator to zero after each service.
However, if you do your own servi-
cing, the procedure for resetting to
zero is as follows:
switch off the ignition,
press and hold the trip distance
recorder zero reset button,
switch on the ignition; the dis-
tance recorder display begins a
countdown,
when the display indicates "=0" ,
release the button; the spanner
disappears.
Following this operation, if you wish
to disconnect the battery, lock the
v e h i c l e a n d w a i t a t l e a s t fi v e m i n u t e s
for the zero reset to be taken into ac-
count. Engine oil level indicator
System which informs the driver
whether the engine oil level is cor-
rect or not.
This information is indicated for a
few seconds when the ignition is
switched on, after the service infor-
mation.
The level read will only be correct if
the vehicle is on level ground and
the engine has been off for more
than 15 minutes.
Oil level correct
Oil level low
This is indicated by displaying of the
message "Oil level incorrect".
I f t h e l o w o i l l e v e l i s c o n fi r m e d b y a
check using the dipstick, it is essen-
tial that the level is topped up to pre-
vent damage to the engine. Oil level gauge fault
This is indicated by displaying of
the message "Oil level measure-
ment invalid". Consult a CITROËN
dealer.
Page 17 of 306
34
1
I N S T R U M E N T S a n d C O N T R O L S
Engine oil temperature gauge
Under normal operating conditions,
the bars should be within section 1 .
In severe operating conditions, the
b a r s m a y e x t e n d i n t o s e c t i o n 2 .
In this event, slow down, and if neces-
sary, stop the engine and check the
levels (see corresponding chapter). Coolant temperature
indicator
Under normal operating conditions,
the bars should be within section
1 .
In severe operating conditions, the
b a r s m a y e x t e n d i n t o s e c t i o n 2 , the
engine coolant temperature warning
lamp A and the STOP warning lamp
will light up, stop immediately . Switch
off the ignition. The cooling fan may
continue to operate for a certain
time .
Consult a CITROËN dealer.
If the SERVICE warning lamp lights
up, check the levels (see correspon-
ding chapter). On horizontal ground, the lighting of
the fuel low warning lamp warns you
that you are at the reserve level.
A message alert is displayed on the
instrument panel.
Fuel gauge indicator
Page 121 of 306
123
9
D R I V I N G
ELECTRICPARKINGBRAKE
The electric parking brake combines
2 operational modes:
- AUTOMATIC
Automatic application when the engine stops and automatic re-
lease on use of the accelerator
(automatic operation by default),
- MANUAL
Manual application/release of the parking brake is always pos-
sible by pulling control A while
pressing the brake pedal. Automatic operation
Application with the engine off
With the vehicle stationary, the parking
brake
is automatically applied when
the engine is switched off.
The application of the parking brake
i s c o n fi r m e d b y : Application with the engine running
With the engine running and the ve-
hicle stationary, in order to immobi-
lise the vehicle you need to manually
apply the parking brake by
pulling
on control A .
The application of the parking brake
i s c o n fi r m e d b y :
- the lighting of the warning
lamp on control A and on
the instrument panel,
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Never leave a child alone inside the
vehicle with the ignition on, as they
could release the parking brake.
- the display of a message "parking
brake applied" on the instrument
panel screen.
T h e n o i s e o f o p e r a t i o n w i l l c o n fi r m t o
you the application/ release of your
electric parking brake. - the lighting of warning
lamp P on control A and
on the instrument panel,
- the display of a message "parking brake applied" on the instrument
panel screen.
When the driver’s door is opened, a
beep is heard and a message dis-
played if the parking brake has not
been applied.
Before leaving the vehicle,
check that warning lamp P
on the instrument panel is
permanently lit.
Page 128 of 306
129
9
D R I V I N G
SITUATIONCONSEQUENCES
4
Display of messages " Parking brake faulty " ultyand " Anti roll-back fault " and of the following faultwarning lamps:
a n d / o r fl a s h i n g
- The automatic functions are deactivated.- The hill start assist is unavailable. To apply the electric parking brake: Immobilise the vehicle and switch off the ignition P u l l t h e c o n t r o l l e v e r f o r a t l e a s t 5 s e c o n d s o r u n t i l m a x i m u m application. Switch on the ignition and check that the electric parking brake warning lamps are on. - Application may take longer than in normal operation. - If warning lamp (!) fl a s h e s o r i f t h e w a r n i n g l a m p s d o n o t c o m e on when the ignition is switched on, this method does not work. Have it checked by a CITROËN dealer. on when the ignition is switched on, this method switched
To release the electric parking brake: Switch on the ignition. P u s h t h e c o n t r o l l e v e r a n d h o l d i t f o r a p p r o x i m a t e l y 3 s e c o n d s .
5
Display of message " Parking brake control faulty – automatic mode activated " and the following warning lamps:
a n d / o r fl a s h i n g
- Only the functions for automatic application on switching off the engine and automatic release on acceleration are available.
- Manual application/release of the electric parking brake anddynamic emergency braking are unavailable.
6
Display of message " Parking brake faulty " and of the following warning lamp:
fl a s h i n g
- Application of the parking brake is not guaranteed.
- The parking brake is temporarily unavailable.
It this situation arises:
W a i t a p p r o x i m a t e l y 3 m i n u t e s .
A f t e r 3 m i n u t e s , i f t h e w a r n i n g l a m p i s s t i l l fl a s h i n g , t r y t o r e i n i -tialise the parking brake, either by pushing and releasing th e control A while pressing the brake pedal or by means of a long pull on control A .
7
Battery fault-Lighting of the battery warning lamp makes it essential to stop t h e v e h i c l e a s s o o n a s t r a f fi c a l l o w s . S t o p a n d i m m o b i l i s e y o u r v e h i c l e .
-Apply the electric parking brake before switching o ff the engine.
Page 130 of 306
131
9
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the
key to position M and wait until
the pre-heating warning lamp
switches off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch whilst turning the starter
to facilitate starting.
Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring A under the knob
and push the gear lever to the
left then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
AUTOMATIC GEARBOX
A u t o m a t i c g e a r b o x w h i c h o f f e r s a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Therefore, you have a choice of four
driving modes:
- automatic operation for elec-
tronic control of the gears by the
g e a r b o x ,
- the SPORT programme for a
more dynamic driving style,
- the SNOW programme to improve
driving when the grip is poor,
- manual operation for sequential
changing of the gears by the driver.
Page 131 of 306
131
9
D R I V I N G
5-SPEED MANUAL GEARBOX
Starting the vehicle
Check that the gear lever is in
neutral.
Do not touch the accelerator.
For Diesel engines: turn the
key to position M and wait until
the pre-heating warning lamp
switches off if it has come on.
Operate the starter, turning the
key until the engine starts (no
more than ten seconds).
In temperatures lower than 0 °C,
declutch whilst turning the starter
to facilitate starting.
Engaging reverse gear
Push the gear lever to the right
then rearwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
6-SPEED MANUAL GEARBOX
Engaging reverse gear
Raise the ring A under the knob
and push the gear lever to the
left then forwards.
Only engage reverse gear when the
vehicle is stationary with the engine
at idle.
As a safety precaution and to facili-
tate starting of the engine:
- always select neutral,
- press the clutch pedal.
AUTOMATIC GEARBOX
A u t o m a t i c g e a r b o x w h i c h o f f e r s a
choice between the comfort of fully
automatic operation, enhanced by
the sport and snow programmes, or
manual gear changing.
Therefore, you have a choice of four
driving modes:
- automatic operation for elec-
tronic control of the gears by the
g e a r b o x ,
- the SPORT programme for a
more dynamic driving style,
- the SNOW programme to improve
driving when the grip is poor,
- manual operation for sequential
changing of the gears by the driver.
Page 133 of 306
133
D R I V I N G Never select positions P or
R if the vehicle is not sta-
tionary.
If, while the vehicle is mov-
ing, position N is engaged inad-
vertently, allow the engine to idle
before engaging position D or M .
Moving off
To start the engine, the selector
has to be in position P or N .
Operate the starter.
When the engine is running,
place the selector on R , D or M
as required.
Check, in the instrument panel,
the position engaged.
Release the brake pedal and
accelerate.
To avoid incoherence between
the position of the selector and
the actual position of the gear-
b o x , a l w a y s e x i t f r o m p o s i t i o n P
with the ignition on and brake
pedal applied.
Otherwise, when the ignition is on or
the engine is running:
reposition the selector in position P ,
put your foot on the brake pedal
and then select the gear you
want. Park
This position of the selector
is used to prevent the vehicle
from moving when you are
stationary.
To select position P, move the
selector back to the highest po-
sition (towards R ), then push it
forwards and then to the left.
T o e x i t p o s i t i o n P , move the selector
to the right and then to the position
you want.
Only engage this position when
the vehicle is completely sta-
tionary. In this position, the front
wheels are locked. Make sure
that the selector is correctly posi-
tioned. Reverse gear
Only engage this position
when the vehicle is station-
ary. To prevent snatching,
do not accelerate too soon
after selection.
Neutral Never select position N if
the vehicle is moving.
Page 139 of 306
139
9
D R I V I N G In the event of a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n , t h e
speed limiter (which does not act
on the brakes) may not be able to
p r e v e n t t h e v e h i c l e f r o m e x c e e d i n g
the programmed speed.
U s e o f a fl o o r m a t o t h e r t h a n t h a t
recommended by CITROËN may
affect the normal operation of the
accelerator pedal and hamper the
operation of the speed limiter.
Floor mats approved by CITROËN
a r e fi t t e d w i t h a 3 r d fi x i n g l o c a t e d i n
the pedal area to avoid any risk of
interference with the pedals.
Suspension/Resumption
Press on button 3 .
This action causes the information
"PAUSE" to appear in zone A of the
instrument panel.
This action does not cancel the
m e m o r i s e d m a x i m u m s p e e d w h i c h
remains displayed in zone A of the
instrument panel. Overriding the programmed
speed
The accelerator pedal has an end-
o f - t r a v e l s w i t c h . I n o r d e r t o e x c e e d
t h e m e m o r i s e d m a x i m u m s p e e d a t
any time, you can press the pedal
all the way down. While the speed
i s b e i n g e x c e e d e d , t h e s p e e d d i s -
played in zone
A w i l l fl a s h . Y o u h a v e
only to release the accelerator pedal
t o r e t u r n b e l o w t h e m a x i m u m s p e e d ,
to restore the function.
T h e s p e e d w i l l a l s o fl a s h i f t h e s p e e d
limiter is not able to prevent the vehi-
c l e f r o m e x c e e d i n g t h e p r o g r a m m e d
speed (e.g. on a steep descent or
u n d e r e x c e s s i v e a c c e l e r a t i o n ) .
To reactivate the speed limiter, release
the accelerator to slow to a speed lower
than the programmed speed.
Return to normal driving
Either press on button 5 .
Or select the speed limiter function.
Or stop the engine.
Operating fault
If there is a malfunction, a message is
displayed accompanied by an audible
signal and lighting of the SERVICE
warning lamp.
Have it checked by a CITROËN
dealer.