ESP CITROEN C6 2005 Workshop Manual

Downloaded from www.Manualslib.com manuals search engine SAFETY REQUIREMENTS: ACTIVE SUSPENSION WITH VARIABLE DAMPING
All operations on the hydraulic suspension circuit must be performed in conformity with the following requirements and regulations:
Authorities competent in matters of health:
- Accident prevention.
- Environmental protection.
WARNING: Operations should be carried out by specialised personnel who have had training in the safety requirements and precautions to
be taken.
Safety requirements.
ESSENTIAL: In view of the special features of the hydraulic suspension system, observe the requirements below, before undertaking any
repair.
IMPERATIVE: Depending on the operation to be carried out, respect the requirements for supporting and securing the vehicle.
Wheels hanging Wheels not hanging
Vehicle on the ground Vehicle on 4-column lift
2-column lift or secure the Depressurisation of the circuit Checking and adjusting of Other operations
vehicle on 4 axle stands(see corresponding operation)heights (switch on ignition) (depressurisation of the
hydraulic circuit)
HYDRAULICS
195
Angl-C6-page195-202-2005 4/02/05 17:36 Page 195

Downloaded from www.Manualslib.com manuals search engine 196
HYDRAULICS
SAFETY REQUIREMENTS: ACTIVE SUSPENSION WITH VARIABLE DAMPING
During the operation.
Wait for the pressure in the hydraulic circuit to fall fully before disconnecting the unions on the following components (risk of sudden sinking of the
vehicle):
- Built-in Hydro-electronic Interface (BHI).
- Front suspension cylinder.
- Rear suspension cylinder.
- Front stiffness regulator.
- Rear stiffness regulator.
- Suspension pressure sensors.
IMPERATIVE: Do not operate on the hydraulic circuit without making the pressure drop (see corresponding operation).
Engine running.
Do not operate on the hydraulic suspension circuit.
Always remain out of range of any possible projections of fluid, as these could cause serious injuries.
NOTE:In the event of contact of LDSfluid with the eyes, rinse them with copious amounts of water and seek specialist advice.
NOTE:In the event of lengthy contact of LDSfluid with the skin, wash it with soap and water.
WARNING: After the engine has stopped, wait 30 seconds before commencing any operation.
Angl-C6-page195-202-2005 4/02/05 17:36 Page 196

Downloaded from www.Manualslib.com manuals search engine HYDRAULICS
197
SAFETY REQUIREMENTS: ACTIVE SUSPENSION WITH VARIABLE DAMPING
IMPERATIVE: Do not remain underneath the vehicle during an operation to adjust vehicle heights or during actuator (electrovalve) tests.
IMPERATIVE: Any deforming of the wheel travel sensor supports is forbidden. If there is any deformation found, replace the component.
Cleanliness requirements.
WARNING: Non-respect of the cleanliness requirements may cause a contamination of the circuit and a malfunctioning of the suspension.
Preliminary operations.
The work area must be kept clean and uncluttered.
The technician must wear clean overalls.
Components being stored during the repair must be protected from dust.
The tooling required for an operation on the suspension system should always be cleaned prior to the operation.
During the operation:
- Before operating on the suspension circuit, proceed to clean the hydraulic components and unions.
IMPERATIVE: Approved cleaner: SODIMAC degreaser.
IMPERATIVE: After a dismantling, immediately blank the hydraulic components and unions with plugs. The plugs should be used for one
operation only.
Any component that has been removed must be plugged and placed in a clean plastic bag.
IMPERATIVE: After a dismantling, any cleaning using compressed air or products is strictly prohibited
. Any LDS fluid that is collected must
not be re-used. Any topping-up must be done with new fluid.
Angl-C6-page195-202-2005 4/02/05 17:36 Page 197

Downloaded from www.Manualslib.com manuals search engine 198
HYDRAULICS
SUSPENSION SPHERES: GENERAL SPECIFICATION
Each suspension sphere is identified at "a", by one number and two letters, marked in bold characters:
- The number consists of 2 digits, corresponding to the nitrogen pressure inside the suspension sphere.
- The two lettersidentify the location of the suspension sphere.
Other information marked on the suspension sphere:
- Day of the year of manufacture.
- Year of manufacture.
- Time of manufacture.
- Factory no. of the suspension sphere.
B3BP1BJD
Angl-C6-page195-202-2005 4/02/05 17:36 Page 198

Downloaded from www.Manualslib.com manuals search engine 201
HYDRAULICS
DE-PRESSURISING THE HYDRAULIC SUSPENSION CIRCUITTools.
[1] PROXIAstation: 4165-T
[2] LEXIAstation: 4171-T
De-pressurisation.
NOTE:It is possible to de-pressurise the suspension by individual axle.
Using a diagnostic tool.
Start the engine.
Place the height control in the «LOW»position.
Wait for the vehicle height to reach the position required.
Stop the engine.
Connect the diagnostic tool [1]or [2]to the vehicle's diagnostic socket.
Switch on the ignition.
Carry out a global test.Go into the menu:
- Suspension.
- De-pressurisation.
Follow the instructions displayed on the screen.
Wait for the vehicle's suspension to sink completely.
NOTE:This operation takes around 3 minutes.
Switch off the ignition.
Disconnect the battery.
Without a diagnostic tool.
IMPERATIVE: Any LDS fluid that is collected must not be re-used.
NOTE:Collect the LDSfluid in order to keep the work area clean.
Respect the environment.
Start the engine.
Place the height control in the «LOW»position.
Stop the engine.
Angl-C6-page195-202-2005 4/02/05 17:36 Page 201

Downloaded from www.Manualslib.com manuals search engine 205
AIR
CONDITIONING
SPECIAL FEATURES: AIR CONDITIONING SYSTEM
Tightening
Requirements for fitting the inlet and outlet brackets:
- Aircon compressor.
- Aircon condenser.
- Aircon pressure reducer valve.
IMPERATIVE: Assembly requirement: the bracket(s) «f» must be against
their interface(s) before the nut(s) are tightened.
IMPERATIVE: Respect the tightening torques.
C5HP1CWC
Angl-C6-page203-217-2005 4/02/05 17:40 Page 205

Downloaded from www.Manualslib.com manuals search engine 206
AIR
CONDITIONING
SPECIAL FEATURES: AIR CONDITIONING SYSTEM (R 134.a)
Pollen filter
The pollen filter is located on the driver's side under the dashboard to the
right of the steering column.IMPERATIVE: Respect the safety and cleanliness requirements.
Removing.
Remove the trim (1)under the dashboard (driver's side).
Release the tab at "b".
Tilt, lift and remove the cover (2).
Remove the pollen filter (3).
NOTE:If the tab "b"is damaged, position a screw for soft materials at "a".
Refitting.
Refit the various components in reverse order to removal.
C5FP0S1CC5HP1BDD
Angl-C6-page203-217-2005 4/02/05 17:40 Page 206