ignition CITROEN DS3 CABRIO 2018 Handbook (in English)

27
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
F
S
witch off the ignition.
F

P
ress and hold the trip distance recorder
reset button.
F

S
witch on the ignition; the distance recorder
display begins a


countdown.
F

W
hen the display indicates "=0", release the
button; the spanner disappears.
Following this step, if you wish to
disconnect the battery, lock the vehicle
and wait at least five minutes for the reset
to be taken into account.
Retrieving the service information
You can access the ser vice information at any
time.
F
P
ress the trip distance recorder reset
button. The ser vice information is displayed
for a
few seconds, then disappears.
Engine oil level indicator
Oil level correct
Low oil level
(Depending on version) The level read will only be correct if the
vehicle is on level ground and the engine
has been off for more than 30
minutes.
It is indicated by "OIL" flashing, accompanied
by the Ser vice warning lamp lighting up, an
audible signal and a

message.
If the low oil level is confirmed by a
check using
the dipstick, the level must be topped up to
avoid damage to the engine.
For more information on Checking levels ,
refer to the corresponding section.
On versions fitted with an electric oil level
indicator, the state of the engine oil level is
displayed in the instrument panel for a
few
seconds after switching the ignition on, after
the servicing information.
01
Instruments

28
AdBlue® range indicators
These range indicators are present only on
BlueHDi Diesel versions.
Once the AdBlue
® tank is on reser ve or after
detection of a

fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of the risk of non-
starting related to a lack of AdBlue®
The engine start prevention system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
Range greater than 1,500

miles (2,400 km)
When switching on the ignition, there is no
automatic display of range in the instrument
panel.
Range between 1,500

miles and 370 miles
(2,400

and 600

km) Go to a
member of the dealer network or
a qualified workshop to have the AdBlue
®
topped up.
You can also top up the tank yourself.
Range below 370

miles (600

km)Oil level indicator fault
It is indicated by " OIL- -" flashing.
Contact the dealer network or a qualified
workshop.
In the event of a
fault with the electric indicator,
the oil level is no longer monitored.
If the system is faulty, you must check the
engine oil level using the manual dipstick
located under the bonnet.
For more information on Checking levels ,
refer to the corresponding section.
When driving, this message is displayed every
30
seconds until the AdBlue level has been
topped up.
Go to a
member of the dealer network or
a
qualified workshop to have the AdBlue
®
topped up.
You can also top up the tank yourself.
Other wise you will not be able to restart the
vehicle.
When switching on the ignition, this warning
lamp comes on, accompanied by an audible
signal and the display of a

message (e.g. "Top
up emissions additive: Starting prevented in
900


miles") indicating the remaining range
expressed in miles or kilometres.
When driving, the message is displayed every
185

miles (300

km) until the level is topped up. When switching on the ignition, this warning
lamp flashes and the Service warning lamp
comes on, accompanied by an audible signal
and the display of a

message (e.g. "Top up
emissions additive: Starting prevented in
350


miles") indicating the remaining range
expressed in miles or kilometres.
01
Instruments

29
For more information on the AdBlue®
(BlueHDi engines) , and in particular on
topping up, refer to the corresponding
section.
Breakdown due to a

lack of AdBlue
®
The AdBlue® tank is empty: the starting
inhibition system required by legislation
prevents starting of the engine.
To be able to start the engine, we
recommend that you call on a
dealer
or a

qualified workshop for the top-up
required.
If you carry out the top-up yourself, it
is essential to add at least 3.8
litres of
AdBlue
® to the tank.
In the event of a fault with the SCR
e missions control system
A system that prevents engine starting is
activated automatically from 685
miles
(1,100
km) after confirmation of a fault with
the SCR emissions control system.
Have the system checked by the dealer
network or a
qualified workshop as soon
as possible.
In the event of the detection of a
faultIf it is a
temporary fault, the alert
disappears during the next journey,
after self-diagnostic checks of the SCR
emissions control system.
When switching on the ignition, this warning
lamp flashes and the Service warning lamp
comes on, together with an audible signal and
the display of the message "Top up emissions
additive: Starting prevented". These warning lamps come on, accompanied
by an audible signal and the display of the
message "Emissions fault".
The alert is triggered while driving as soon
as the fault is detected for the first time, then
when switching on the ignition for subsequent
journeys, while the fault persists.During the permitted driving phase
(between 685
and 0 miles (1,100 km and
0


km))
If a
fault with the SCR system is confirmed
(after 30
miles (50 km) covered with the
permanent display of the message signalling
a
fault), these warning lamps come on and the
UREA warning lamp flashes, associated with
an audible signal and the display of a
message
(e.g. "Emissions fault: Starting prevented in
190


miles") indicating the remaining range
expressed in miles or kilometres.
While driving, the message is displayed every
30 seconds while the fault with the SCR emission
control system persists.
The alert is repeated when switching on the ignition.
You should go to a
network dealer or a qualified
workshop as soon as possible.
Other wise you will not be able to restart the vehicle.
01
Instruments

30
Starting preventedYou have exceeded the authorised driving
limit: the starting prevention system does
not allow the engine to be started.
To be able to restart the engine, you must
call on a
member of the dealer network or
a


qualified workshop.
Distance recorders
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked. When travelling abroad, you may need
to change the unit of distance: the speed
display must be expressed in the official
unit of the country (km or mile). The
change of units is done via the screen
configuration menu, with the vehicle
stationary.
Total distance recorder
It measures the total distance travelled by the
vehicle since its first registration.
Trip distance recorder
It measures the distance travelled since it was
reset by the driver.
F

W
ith the ignition on, press the button until
zeroes appear.
Each time the ignition is switched on, these
warning lamps come on and the UREA
warning lamp flashes, accompanied by an
audible signal and the display of the message
"Emissions fault: Starting prevented".
Lighting dimmer control
System that allows the brightness of the
instruments and controls to be manually
adjusted to suit the ambient light level.
01
Instruments

40
A few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remaining
in the tank (at the average fuel
consumption seen over the last
distance travelled).
This value may fluctuate if a
change
of driving style or terrain results in
a

significant change in the current fuel
consumption.
When the range falls below around 20
miles
(30

km), dashes are displayed. After filling with
at least 5

litres of fuel, the range is recalculated
and is displayed if it exceeds around 60
miles
(10 0


k m).
If dashes instead of figures continue to be
displayed when driving, contact the dealer
network or a
qualified workshop.
Current fuel consumption
(mpg or km/l or l/100 km)
C alculated during the last few
seconds. This function is only displayed from
around 20 mph (30 km/h).
Average fuel consumption
(mpg or km/l or l/100 km)
C alculated since the last time the
trip recorder was reset to zero.
Average speed
(mph or km/h)
Calculated since the last time the
trip recorder was reset to zero.
Distance travelled
(miles or km)
Calculated since the last time the
trip recorder was reset to zero.
Distance remaining to travel
(miles or km)
This is the distance remaining to
travel before the final destination is
reached. It can be input by the user.
If the distance is not entered, dashes
are displayed instead of numbers.
Stop & Start time counter
(minutes/seconds or hours/minutes)
If your vehicle is fitted with Stop &
Start, a time counter adds up the
time spent in STOP mode during
a


j o u r n ey.
It is reset to zero every time the
ignition is switched on using the key.
Date and time adjustment
With monochrome screen A
F Press the MENU button.
F S elect "Display settings" using the buttons
" 5 " or " 6".
F

P
ress " OK" to confirm the selection.
F

S
elect the "Year" function using the buttons
" 5 " or " 6".
F

P
ress " OK" to confirm the selection.
F

D
efine the desired value using the buttons
" 7 " or " 8".
F

P
ress " OK" to confirm the selection.
F

R
estart the procedure for the settings
"Month", "Day", "Time", and "Minutes".
01
Instruments

44
With the remote control
F Press the closed padlock to lock the vehicle completely.
F

P

ress the closed padlock again within five
seconds to deadlock the vehicle.
With the key
F Turn the key to the rear in the driver's door lock to lock the vehicle completely.
F

T
urn the key to the rear again within five
seconds to deadlock the vehicle.
Deadlocking is confirmed by fixed illumination
of the direction indicators for approximately two
seconds.
Depending on your version, the door mirrors
fold at the same time.
Locating your vehicle
F Press the closed padlock to locate your locked vehicle in
a


car park.
This is indicated by lighting of the courtesy
lamps and flashing of the direction indicators
for a

few seconds.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst of all, use the key in the door lock to
unlock or lock your vehicle.
F

T
hen reinitialise the remote control.
If the problem persists, contact the dealer
network as soon as possible.
Reinitialisation
Battery type: CR1620/3 volts.
F

S

witch off the ignition.
F

T

urn the key to position 2


(Ignition) .
F

P

ress the closed padlock button for a

few
seconds.
F

S

witch off the ignition and remove the key
from the switch.
The remote control is now fully operational
again.
Changing the battery
If the battery is discharged, you are
informed by lighting of this warning lamp in
the instrument panel, an audible signal and
a
message in the multifunction screen.
F Unfold the key.
F U nlock the chrome finisher by pressing
lug A .
F

K
eep lug A pressed in and remove the
chrome finisher by sliding it at 45°.
F

U
nclip the unit by inserting a coin into the
slot and per forming a
rotation movement.
02
Access

45
Lost keys
Go to a member of the dealer network, taking
with you the vehicle's registration certificate,
your personal identification documents and if
possible, the label bearing the key code.
The member of the dealer network will be able
to look up the key code and the transponder
code required to order a
new key.
Do not throw away the remote control
batteries, they contain metals which are
harmful to the environment.
Take them to an approved collection
point. Anti-theft protection
Do not make any modifications to the electronic
engine immobiliser system; this could cause
malfunctions.
Remote control
The high frequency remote control is a
sensitive
system; do not handle it while it is in your pocket
as there is a
possibility that it may unlock the
vehicle without you being aware of it.
Do not repeatedly press the buttons of your
remote control out of range and out of sight of
your vehicle. You may stop it from working and
the remote control would have to be reinitialised.
No remote control can operate when the key is
in the ignition switch, even when the ignition is
switched off, except for reinitialisation.
Locked vehicle
Driving with the doors locked could make it
difficult for the emergency services to enter the
vehicle in an emergency.
As a
safety precaution, never leave children
alone in the vehicle, except for a
very short
period.
In all cases, it is essential to remove the key
from the ignition switch when leaving the
vehicle. Second-hand vehicle
Have the pairing of all of the keys in your
possession checked in the dealer network, to
ensure that only your keys can be used to open
and start the vehicle.
F
S
lide the discharged battery out of its
location.
F

S

lide the new battery into its location,
observing the original direction of fit.
F

C

lip in the unit then the chrome finisher.
F

R

einitialise the remote control.
02
Access

46
Alarm
- Perimeter protection
The system manages the opening of the
vehicle.
The alarm is triggered if anyone tries to open
a door, the boot or the bonnet.
- Volumetric protection
(Except Cabrio versions)
The system manages any variation in the
volume of the passenger compartment.
The alarm is triggered if anyone breaks
a
window or moves inside the vehicle.
When leaving an animal in the vehicle or
a
window open, deactivate the volumetric
protection. This system protects and provides a deterrent
against theft and break-ins.
It provides the following types of monitoring: Do not make any modifications to the alarm
system; this could cause malfunctions.
Locking the vehicle with
complete alarm
Activation
F Switch off the ignition and get out of the
vehicle.
F

L
ock or deadlock the vehicle using the
locking button on the remote control.
The alarm activates; the indicator lamp in
button A flashes once per second.
The perimeter protection is activated 5
seconds
after pressing the locking button on the remote
control.
The volumetric protection is activated
45
seconds after pressing the locking button on
the remote control. If an opening – door, boot, etc. – is
incorrectly closed, the vehicle is not
locked but the perimeter protection will be
activated after 45


seconds.
Deactivation
F Unlock the vehicle using the unlock button
on the remote control.
The alarm is deactivated: the indicator lamp in
button A goes off.
Locking the vehicle with
exterior perimeter protection
only
Deactivating the volumetric
protection
F Switch off the ignition.
F W ithin ten seconds, press button A until the
indicator lamp is on continuously.
F

G
et out of the vehicle.
F

L
ock or deadlock the vehicle quickly using
the locking button on the remote control.
The exterior perimeter protection alone
remains active; the indicator lamp in button A
flashes once per second.
- Self-protection function
(Except Cabrio versions)
The system manages the deactivation status of
its components.
The alarm is triggered if the battery, central
control unit or the siren wiring is taken out of
service or damaged.
02
Access

47
To take effect, this deactivation must
be carried out each time the ignition is
switched off.
Reactivating the volumetric
protection
F Unlock the vehicle using the unlocking button on the remote control.
F

L
ock the vehicle using the remote control.
The alarm activates again with the two
protections; the indicator lamp in button A
flashes once per second.
Triggering of the alarm
This is indicated by the sound of the siren
and the flashing of the direction indicators for
around thirty seconds.
After triggering, the protection is operational
again.
If the alarm is triggered ten times in
succession, on the eleventh occasion it
becomes inactive. Rapid flashing of the indicator lamp in
button A informs you that the alarm was
triggered during your absence. When the
ignition is switched on, this flashing stops
immediately.
To avoid triggering the alarm, when
washing your vehicle lock it using the key
in the driver's door lock.
Failure of the remote control
F Unlock the vehicle using the key in the
driver's door lock.
F

O
pen the door; the alarm is triggered.
F

S
witch on the ignition; this stops the alarm.
Locking the vehicle without
activating the alarm
F Lock or deadlock the vehicle using the key in the driver's or passenger's door lock.
Malfunction
When the ignition is switched on, illumination of
the indicator lamp in button A for ten seconds
indicates a
fault in the siren.
Have it checked in the dealer network or by
a


qualified workshop.
Automatic activation
(Depending on country of sale.)
The alarm is activated automatically 2 minutes
after the last door or the boot is closed.
F

T
o avoid triggering the alarm on entering the
vehicle, first press the unlocking button on
the remote control.
Electric windows
Equipped, on the driver side, with an anti-pinch
protection function.
1. Driver's electric window control.
2. Passenger's electric window control.
02
Access

48
The electric window controls remain
active for approximately 45 seconds after
the ignition is turned off, or until a
door is
opened. During this period of 45
seconds,
if you open a
door while operating
a
window, the window stops. Any new
electric window command will be ignored
until the ignition is switched back on.
Electric passenger window
F Press or pull the control. The window stops as soon as the
switch is released.
Sequential electric driver
window
There are two options:
-

man

ual mode
F

P

ress or pull the control gently, without
exceeding the point of resistance. The
window stops as soon as the control is
released.
Safety anti-pinch
The sequential electrical window on the driver
side has an anti-pinch function.
When the window rises and meets an obstacle,
it stops and partially lowers again.
In the event of unwanted opening of the
window on closing (for example, when
f re ezing):
F

p
ress the control beyond the point of
resistance and release it; the window
opens fully,
F

t
hen immediately pull the control
without passing the point of resistance
until the window is fully closed,
F

c
ontinue to hold the control for
approximately one second after the
window has closed.
The safety anti-pinch function is not
operational during these operations.
Reinitialisation
If a fault occurs, you must reinitialise the
el ectric window operation:
F

r
elease the control and pull it again until the
window closes fully,
F

c
ontinue to hold the switch for
approximately one second after the window
has closed,
F

p
ress the control to lower the window
automatically to the low position.
The safety anti-pinch function is not
operational during these operations.
-

a

utomatic mode
F
P
ress or pull the switch fully, beyond the
point of resistance. The window opens
or closes completely when the switch is
released.
F

P

ressing the switch again stops the
movement of the window.
Always remove the key from the ignition
when leaving the vehicle, even for a
short
time.
In the event of contact during operation
of the windows, you must reverse the
movement of the window. To do this, press
the switch concerned.
When the driver operates the passenger
electric window switch, they should ensure
that no-one is preventing correct closing
of the window.
Be particularly aware of children when
operating the windows.
02
Access