long Citroen JUMPY 2016 2.G Owner's Manual

13
Jumpy _en_Chap00c_eco-conduite_ed01-2016
Limit the causes of excess
consumption
Spread loads throughout the vehicle; place the
heaviest items in the bottom of the boot, as
close as possible to the rear seats.
Limit the loads carried in the vehicle and reduce
wind resistance (roof bars, roof rack, bicycle
carrier, trailer...). Use a roof box in preference.
Remove roof bars and roof racks after use.
At the end of winter, remove snow tyres and refit
your summer tyres.
Observe the recommendations
on maintenance
Check the tyre pressures regularly, when cold,
referring to the label in the door aperture,
driver's side.
Carry out this check in particular:
-
b
efore a long journey,
-

a
t each change of season,
-

a
fter a long period out of use.
Don't forget the spare wheel and the tyres on
any trailer or caravan.
Have your vehicle serviced regularly (engine
oil, oil filter, air filter, passenger compartment
filter...) and observe the schedule of operations
recommended in the manufacturer's service
schedule.
With a BlueHDi Diesel engine, if the SCR
system is faulty your vehicle becomes polluting;
go to a CITROËN dealer or a qualified
workshop without delay to have the emissions
of nitrogen oxides brought back to the legal
level. When refuelling, do not continue after the third
cut-off of the nozzle to avoid any over flow.
At the wheel of your new vehicle, it is only after
the first 1 800 miles (3 000 kilometres) that you
will see the fuel consumption settle down to a
consistent average.
.
Eco-driving

22
Warning / indicator lampStateCause Action / Observations
Under-inflation fixed, accompanied by
an audible signal and
a message. The pressure in one or more tyres is
too low.
Check the tyre pressures as soon as possible.
This check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after the adjustment
of one or more tyre pressures and after changing one
or more wheels.
For more information on Under-inflation detection
,
refer to the corresponding section.
+ flashing then fixed,
accompanied by the
Service warning lamp.The system has a fault: the tyre
pressures are no longer monitored.
Check the tyre pressures as soon as possible.
Have the system checked by a CITROËN dealer or a
qualified workshop.
Foot on the
brake pedal fixed.
The brake pedal must be pressed. With an automatic or electronic gearbox, press the
brake pedal, engine running, before releasing the
parking brake, to release the selector lever and come
out of position P or N.
If you wish to release the parking brake without
pressing the brake pedal, this warning lamp will
remain on.
Foot on the
clutch fixed.
In the STOP mode of Stop & Start,
the change to START mode is denied
because the clutch pedal is not fully
down. If your vehicle has a manual gearbox, you must
declutch fully to allow the change to engine START
mode.
Instruments

54
Jumpy _en_Chap02_ouvertures_ed01-2016
Changing the battery
Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.If the battery is flat, you are
informed by lighting of this warning
lamp in the instrument panel, an audible signal
and a message in the screen.
Reinitialisation
Locking the side-hinged doors
F If fitted to your vehicle, check that the
electric child lock is not on.
F

O
pen the left-hand door. Battery ref.: CR1620 / 3 volts.
F
L
ock the driver's door using
the
key.
F

P
ress one of the remote control
buttons.
F

T
urn the key to position 2 (Ignition on).
F

S
witch off the ignition and remove the key
from the ignition switch.
The remote control is fully operational again.
Unlocking
F Use the interior door handle.
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst of all, use the key in the lock to unlock
or lock your vehicle.
F

T
hen reinitialise the remote control.
If the problem persists, contact a CITROËN
dealer as soon as possible.
F

U
nclip the cover using a screwdriver in the
cut-out.
F

R
emove the cover.
F

E
xtract the flat battery from its location.
F

P
lace the new battery into its location
observing the original direction.
F

C
lip the cover in place.
F

I

nsert the key into the latch aperture on the
edge of the door (without forcing) and slide
the assembly upward.
F

R

emove the key.
F

C

lose the door and check from the outside
that it has locked correctly.
Access

70
Jumpy _en_Chap02_ouvertures_ed01-2016
Changing the battery
Battery ref.: CR2032 / 3 volts.
This replacement battery is available from a
CITROËN dealer or a qualified workshop.
A message appears in the instrument panel
screen when replacement of the battery is needed.Do not throw the remote control
batteries away, they contain metals
which are harmful to the environment.
Take them to an approved collection
point.
F

P

lace the remote control against the
reader.
F

K

eeping it in place, switch on the ignition
by pressing "START/STOP".
The remote control is fully operational again.
Reinitialisation
Remote control problem
Following disconnection of the vehicle battery,
replacement of the remote control battery or
in the event of a remote control malfunction,
you can no longer unlock, lock or locate your
vehicle.
F

F
irst, use the integral key in the door lock
to unlock or lock your vehicle.
F

T
hen, reinitialise the remote control.
If the problem persists, contact
a CITROËN dealer or a qualified
workshop as soon as possible.
F

U
nlock the driver's door using the
integral
key.
F

P
ress one of the remote control
buttons.
F

P
lace the integral key in the lock to unlock
your vehicle. F

U
nclip the cover using a small screwdriver
at the cutout.
F

L
ift off the cover.
F

R
emove the flat battery from its location.
F

F
it the new battery into its location
observing the original direction of fitment.
F

C
lip the cover onto the casing.
Access

72
Jumpy _en_Chap02_ouvertures_ed01-2016
Locking the vehicle
This button is inoperative if the vehicle
has been locked or deadlocked from
outside (using the key, remote control or
Keyless Entry and Starting, according
to equipment) or if one of the doors is
still open.
Automatic
The cabin doors lock automatically while
driving (speed above 6 mph (10 km/h)); the
indicator lamp comes on.When carrying long objects with the
tailgate or rear doors open, you can
press this button to lock just the cabin
doors.
When locking from inside, the door
mirrors do not fold.
The indicator lamp also goes off when
unlocking one or more doors.
Driving with the doors locked may make
access to the passenger compartment
by the emergency services more
difficult in an emergency.
F
T
o activate or deactivate this
function, with the ignition on,
press this button until a message
appears in the screen. F

P
ress this button.
F
P
ress this button.
If the vehicle is deadlocked or locked
with the remote control or the door
handles, the button is not active. In this
case, use the key or the remote control
to unlock.
Manual
The indicator lamp comes on to confirm the
locking. The indicator lamp goes off to confirm the
unlocking.
Unlocking the vehicle
Locking / unlocking from inside
Access

85
Jumpy _en_Chap02_ouvertures_ed01-2016
When open, a door never projects
beyond the rear bumper.
The doors and the overall
dimensions of the vehicle
When open, a door projects beyond the body.
Be sure to take this into account when you park
alongside a wall, a post or a high kerb...
Safety / Obstacle detection with
electric door(s)Fuel filler flap
The obstacle detection system is triggered
when the moving door encounters an obstacle
with a certain level of physical resistance.
-

I
f an obstacle is detected while the door is
closing, the door stops then opens fully.
-

I
f an obstacle is detected while the door is
opening, the door stops and then closes.
-

I
f an obstacle is detected twice in
succession during a movement of the door,
it will no longer close electrically. Close the
door manually to reinitialise it. If fitted to your vehicle, never open the
left-hand sliding side door when the
fuel filler flap is open. Other wise you
risk damaging the fuel filler flap and the
sliding door and causing injury to the
person filling the vehicle.
If the fuel filler flap is open and your
vehicle has an electric left-hand sliding
side door, the door cannot be opened
using the opening control button. If
required the door can be opened half
way manually. The fuel filler flap must
be closed to allow the door to open
correctly
2
Access

86
Jumpy _en_Chap02_ouvertures_ed01-2016
In the case of a steep slope, the door
may be driven by its own weight and
as a consequence may open or close
j e r k i l y.
There would not be time for action at
the electric controls to take effect.
There would not be time for the
obstacle detection system to react.
Take care not to leave the vehicle on
a steep slope with the door(s) open
without supervision. If this advice is not
followed, injuries or damage may occur
if a person or an object is trapped or
caught.
On a steep slope
It is possible to open and close the doors
electrically on slopes of up to 20%.
However, if your vehicle is on a slope, with the
front of the vehicle facing up, open the door
with care. The door may open more quickly due
to the incline.
On a steep slope, guide the side door manually
to help it to close. However, if your vehicle is on a slope, with the
front of the vehicle facing down, the door may
not stay open and may close again jerkily with
the risk of injury.
Reinitialising electric doors
Following disconnection of the battery with the
doors open, it may be necessary to close the
doors manually to reinitialise them.
If the doors no longer work electrically,
reinitialise the door(s) as follows:
F

F
ully close the door(s) manually.
F

F
ully open the door(s) manually.
F

C
lose the door(s) manually.
F

F
ully open the door(s) manually.
F

C
lose the door(s) manually.
On completion of this procedure, electric
operation of the doors is restored.
However, if a problem persists following this
procedure, contact a CITROËN dealer or a
qualified workshop.
Access

101
Jumpy _en_Chap03_ergonomie-et-confort_ed01-2016
F Place the head restraint in the low position, and if fitted to your vehicle, raise the
armrest and fold the table on the back of
the seat.
Table position for the
driver's and/or the
front passenger's seat
backrest
Check that there is no object that could
inter fere with the movement of a seat,
both above and below.
On the front passenger's side, this position
allows long objects to be carried.
On the driver's side, this position allows rear
passengers to be helped out of the vehicle (by
the emergency services).
F
P
ull the control fully up and tip the backrest
forward.
To return to the normal position, pull the
control up to release the backrest, then pull the
backrest up to its raised position.
3
Ease of use and comfort

104
Jumpy _en_Chap03_ergonomie-et-confort_ed01-2016
Head restraint height
adjustment
F To raise the head restraint, pull it upwards.
F T o remove the head restraint, press the
lug
A and pull the head restraint upwards.
F

T
o put the head restraint back in place,
engage the head restraint stems in the
openings keeping them in line with the seat
back.
F

T
o lower the head restraint, press the lug A
and the head restraint at the same time. The head restraint rods have notches
which prevent the head restraint
lowering; this is a safety device in case
of impact.
The adjustment is correct when the
upper edge of the head restraint is
level with the top of the head.
Never drive with the head restraints
removed; they must be in place and
adjusted correctly.
2-seat front bench seat
If fitted to your vehicle, this is fixed and has a seat belt on the backrest for the seat alongside the
driver.
For more information on the Seat belts,
refer to the corresponding section.
Ease of use and comfort

106
Jumpy _en_Chap03_ergonomie-et-confort_ed01-2016
Moduwork
Removing the flap
Removable flap
F Holding the flap with one hand, with your other hand turn the control at the top of the
flap to release it.
F

L
ower the flap to remove it from its
housing.
The cushion of the outer seat of the bench
seat can be raised up to the backrest to create
additional loading space in the cab.
A flap in the partition can be removed to allow
long objects to be carried.
Once the removable flap has been
removed, you can load long objects
under the outer seat. F

S
tow it behind the driver's seat, clipping it
to the fixing lugs.
F
T
urn the control at the top of the flap to
secure it.
Ease of use and comfort