engine DACIA SOLENZA 2004 Repair Manual
[x] Cancel search | Manufacturer: DACIA, Model Year: 2004, Model line: SOLENZA, Model: DACIA SOLENZA 2004Pages: 891, PDF Size: 14.84 MB
Page 523 of 891
BATTERY - FRONT HEADLIGHTS
80
80 - 2
ATTENTION !
In case of acid splashes on body, abundantly wash with water all affected parts.
If eyes have been touched, urgently call for a doctor.
1. DANGER = EXPLOSION RISK
During battery charging, connected to a charger-rectifier, oxygen and hydrogen emissions are
occurring. These gases emission is stronger when the battery has reached the complete charge
condition and the produced gas quantity is in direct connection with the charging current.
The oxygen and hydrogen are associating in the free spaces, at the plates surface, forming a
detonate mixture, which is very explosive. The littlest spark is sufficient to generate an explosion,
followed by the battery case brooking and a cid splashing in the proximate environment. The
persons, who are a round, are in da nger t o be hurt by t he e xploded case chips or by the acid,
which may come i n contact with the eyes, hands, or face.
ATTENTION !
Strictly observe the following recommendations:
- before connecting or reconnecting a battery, ensure that all consumers are shouted off.
- during battery charging in a room, using a charger-rectifier, turn it off before connecting or
reconnecting the battery to this one;
- do not place metallic objects on t he ba ttery for not producing a short-c ircuit between i ts
pl ugs ;
- never bring closer to a battery, a n open flame, a welding lamp or another fire source.
THE ELECTRIC EQUIPMENT PROTECTION
In case of an intervention on the vehicle, some measures must be taken, for the electric equip-
ment protection against damages or for avoiding a short-circuit that may lead to vehicle firing.
The battery is to be allwith disconnected by first disconnecting the negative plug and then t he
positive one. Connection is to be done by performing the disconnecting operations in the reverse
order.
Before starter acting, check if the battery is correctly connected (the negative plug connected
to the mass), and if the plugs are clean and well tightened. Never disconnect the battery when the
engine is running, in order not to damage the voltage regulator, the alternator or some components
of the vehicle checking electronic systems. The alternator, voltage regulator disconnecting, and
the interventions at their connections, are to be performed only when the engine is stopped (the
alternator is not turning) and the contact is taken off. In case the battery is connected to a charger-rectifier, for charging (without dismounting the
battery off the vehicle), it is obligatory to disconnect the wiring from the battery plugs.
Battery
vnx.su
Page 544 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 1
This type of anti starting system is based on the key recognition, which has a special constructio n.
It may be separated in two elements which can be identified in the following way: the key head
(position A.) made of plastic, which c an be dismounted and the metal insertion (position B),
which is fixed and ensured by clipping in the key head.
In the key head, there is a coded independent electronic circuit, which is functioning without
battery. When setting the contact on, the anti starting bushing, placed around the starting contact,
is enquiring and catching the coded signal emitted by the key head, then sends it to the Electronic
Control Unit (E.C.U.) decoder. This one is attached on the front left pillar, under the lower casing
of the dashboard and has the function of receiving the code sent from the bushing. If the decoder
recognises the key code then it will send a coded signal to the injection computer, which compares
it with the previous memorised code and will authorise or not the engine starting In case of the system with ra dio frequency remote control (RF) of the doors blocking /
unlocking, the key head has a different construction, having an activation button of the remote
control and a red L ED, which i s lighted i n the moment of bl ocking/unlocking the doors, by
pushing the key button. Inside t he ke y head there i s the coded electroni c c ircuit for the anti
starting system and a printed electronic circuit, supplied by a battery, for the RF remote control
operation of blocking/unlocking the vehicle doors.
The anti starting system is activated after approximate 10 seconds from the breaking of the
contact and is visualised by the blinking of the anti starting indicator placed on the instrument
panel.
AT T E N T I O N !
If the battery is low charged, the tension drop on the starter, at starting, may cause
the activation of the anti starting system and the engine starting is impossible.
General
vnx.su
Page 546 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 3
The E.C.U. decoder has the following functions :
- deco ding the signal received from the anti starting
bushing; - send ing a code to the injection computer in order to
author ise the engine starting;
- c ontrolling the anti starting indic ator of the instrument
panel;
receiv ing the coded signal from the anti starting bearings,
for the vehicles equipped with RF remote control;
REMA RK :
In case both keys were lost, the code of the key head (8 characters) and the code of the
me tal insertion (4 characters) can be red from the vehicle-purchasing invoice. If also the
invoice was lost, the two mentioned codes can be found out based on the chassis s eries of that
vehicl e, acces sing the database of the DA C IA manufacture r, callin g the “C lient Voice”
department (phone 0248 500 000).
E.C.U. DECODER
General
- commandi ng the blocking/unlocking of the doors, if the vehicle is provided with RF remote
c ontrol keys;
- co mma nding the ceiling delayed light, for vehicles equipped with this system.
Th
e an ti starting bushing is located around the starting contact and is accessible after the
d ismounting the steering wheel’s half-cases. It catches the signal from the key head and then sends
a coded signal to the E.C.U. decoder.
The ve hicles equipped with RF remote control keys for blocking/ unlocking the doors are provided
with another anti starting bushing which transmits to the E.C.U. decoder also the signal received
from the RF remo te control.
Th e recognition of the two types of decoding bushings is performed by means of codes labelled
on their body, as follows : - code 04 2264J - for vehicles without RF remote control;
- code 8200 044257 - for vehicles with RF remote control. ANTI S TARTING BUSHING
vnx.su
Page 550 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 7
If, further to the diagnostic by means of the CLIP tester, it is established the necessity of the
rep lacement of the anti starting bushing, proceed as follows:
- d isconnect the (-) terminal of the battery;
- d ismount the attachment screws of the steering wheel half-casings ;
- detach from clips the steering wheel half-casings;
- remove the steering wheel half-casings;
- d isconnect the anti starting bushing connector from the front wiring;
- remove the bushing;
- mount the new bushing outside the starting contact (anti theft mechanism);
- co nnect the bushing connector to the front wiring;
- a ttach in clips the steering wheel half-casings and mount the attachment screws;
- check the operation of the indicator and the anti starting system when the contact is off, then
with the contact on and then with the engine started.
Anti starting bushing replacement
vnx.su
Page 552 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 9
If further to the diagnostic by means of the CLIP tester, it is necessary the replacement of the
E. C.U. (computer) injection, for its dismounting, proceed as follows:
-disconnect the battery (the contact being off);
-d ismount the screw from the battery attachment clip;
-remov e the battery;
-d ismount the two attachment nuts of the injection computer and of the ECU protector;
-remov e the injection ECU protector;
-d isconnect the injection computer from the engine wiring;
-d ismount the ECU injection
For mounting, perform the dismounting operations in the reverse order.
The in jection computer is delivered not coded. It is necessary the memorising of an anti starting
code in the computer, after this has been mounted.
Proceed as follows: 1. Set the contact on, without starting the engine, for 5 seconds.
2. Ta ke off the contact; after 10 seconds, the anti starting function is activated, and the anti
starting indicator will blink rarely (one blink per second). 3. Set the contact on. The anti starting indicator must turn off after 3 seconds and the engine
can be started. In or der to disconnect the injection computer (E.C.U. injection) act upon the blocking lever (A)
of the connector in the direction of the B arrow, then the connector will be lifted in the direction of
the C arrow. In ca se the vehicle is blocked on the road further to serious damages of the anti starting system,
the “ Procedure for repairing code introduction” may be used, which allows the moving of the
vehicle to the nearest DACIA service centre for complete repairing. In order to perform this
procedur e it is necessary the CLIP tester and the specific repairing code of that vehicle.
A
B
C
Electric control unit injection replacement
vnx.su
Page 554 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 11
REPLACEMENT OF THE ACCOUSTIC WARNING
(for auto made after 03.07.2003)
The ne w acoustic warning i s attached in t he engine c ompartment, on the left upper front
longitudinal girder.
1 2
DISMOUNTIN
G
Disconnect the battery (-) terminal.
Remove by hand the battery screen from the acoustic warnin g attaching area so that dismounting
of the screw ( 1) is permitted.
Di smount the screw ( 1) attaching the acoustic warning on the l eft upper front longitudinal
girder.
Disconnect the acoustic warning connector (2).
Carefully remove the acoustic warning
REMOU NT I NG
Perform the dismounting operations in the reverse order.
Check the operation of the acoustic warning.
REMARK !
Eac h t i me whe n di smount i ng t he ac oust i c warni ng, re pl ac e the fan-t y pe the
attachm ent screw ( 1) .
The required tightening moment of t he attachment screw is of 21 Nm + 10%.
Acoustic warning
vnx.su
Page 556 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 13
Procedures
1. Return to “COMPUTER TEST”
2. Set the contact on for 2 seconds in “ M” position, without start ing the engine. The anti
starting indicator will begin to blink rapidly.
3. Access the menu “ STATE LIST”, where the following states must exist:
9D RECEIVED KEY CODE ………………………………......…… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….…… PASSIVE
10. Take the c ontact off. In the menu “COMMAND MODE” select “ACTUATORS”, then
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear, followed
by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE LIST”, which now, must be like that: 18G FIRST CYCLE MEMORISING…………………………….....…ACTIVE
19G NOT PERFORMED KEY PROGRAMMING…………….……..PASSIVE
19D UNBLOCKED KEY PROGRAMMING …………………..…… PASSIVE
13. Set the contact i n “M” position for 2-3 seconds in order t o send the code t o the E.C.U.
injection. The anti starting indicator must light for 3 seconds, then turn off.
14. Take off the contact. After 10 seconds, the anti starting indicator will blink rarely.
15. Check the engine starting with both keys, and then take the contact off.
16. Check in the menu “ STATE LIST ” if the state 10G “ANTI STARTING” is “ ACTIVE”.
Perform the synchronisation of the TRF remote control with the decoder (with 1or 2 keys).
OBSERVAT ION:
With the CLIP tester, a starting interdiction may be simulated, proceeding as follows:
- take the contact off; wait for 10 seconds, then the anti starting indicator will blink;
- in the menu, “COMMAND MODE” access “ ACTUATORS” then validate “ FORCED
PROTECTION MODE” launching the command from the blue button situated on the ri ght
topside of the screen. “COMMAND IN PROGRESS” will be displayed and then “FINISHED
COMMAND”; - in t he m enu “ STATE LIST” search for the state 10G ”ANTI START ING”, which
must be “ ACTIVE”; - set the contact on “M” position; the anti starting indicator will blink rapidly, and the
engine starting is impossible;
- remove the key from the contact and check then the engine starting with both keys, so
the procedure is finished.
vnx.su
Page 558 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 15
Procedures
7. Set the contact i n “M” position with one of the ke ys (without start ing the engine), for
about 2 seconds and then check the following states, which must be:
9D RECEIVED KEY CODE ……………………………….....…..... ACTIVE
19G NOT PERFORMED KEY PROGRAMMING ………….........… ACTIVE
8. Set the contact with the second key (without starting t he engine) for about 2 seconds.
Check then the following states:
-case (a)- the second key belongs to the vehicle;
9D RECEIVED KEY CODE ……………………………………..… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING …………….....… PASSIVE
- case (b)- t he second key doe s not belong to t he vehicle or the first ke y was used once
again;
9D RECEIVED KEY CODE ……………………………………..… PASSIVE
19G NOT PERFORMED KEY PROGRAMMING ………….....…… ACTIVE
9. The anti starting indicator blinks rapidly.
10. Take off the contact. In the menu “ COMMAND MODE” select “ACTUATORS” and
validate “ FINISHED CALIBRATION” launching the command on the blue rectangle situated
on the right top of the screen. The message “COMMAND IN PROGRESS” will appear,
followed by “ FINISHED COMMAND”. 11 . The anti starting indicator will blink rarely.
12. Return to the “STATE L IST”, which now must be as follows: 18G FIRST KEY MEMORISING…………………………….........… ACTIVE
19G NOT PERFORMED KEY PROGRAMMING……………...……PASSIVE
19D UNBLOCKED KEY PROGRAMMING ………………...…...…PASSIVE
13. In the menu “COMMAND MODE” select “ ACTUATORS”. Select the command “
FORCED PROTECTION MODE” launching the command from the blue button situated on
the ri ght topside of the screen. The display will show “COMMAND IN PROGRESS” and
then “FINISHED COMMAND”.
Return to the “STATE LIST “ and check t he state: 9GFORCED PROTECTION MODE ………………………....…… ACTIVE
14. Set the contact on “M” position. The anti starting indicator will start to blink ra pidly.
Check in the “ STATE LIST” if the state “ANTI STARTING” is “ACTIVE”.
15. In the menu “COMMAND MODE” a ccess “ACTUATORS”, then select the command
“ MANUAL CODE INTRODUCTION”. Type t he four fi gures of the repairi ng code, t hen
validate with the key “ENTER”. On the screen the message “COMMAND IN PROGRESS”
w ill appear and then “FINISHED COMMAND”.
16. Set the contact off and then set again the contact on, without starting the engine, in order
to send the new anti starting code to the injection computer. The anti starting indicator will light
for 3 seconds, and then it will turn off.
vnx.su
Page 559 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 16
Procedures
17. The procedure is finished. Check the engine starting with both keys.
REMARK:
For the RF remote control synchronisation, after the replacement of a kit, take into account
the following situations:
- for the first RF remote control, perform the “ SIMPLE SYNCHRONISED PROCEDURE”;
- for t he second RF re m ote control pe rform the “SPE CIFIC SYNCHRONISE D
PROCEDURE”. C. CODE REPAIRING INTRODUCTION PROCEDURE
The repairing code may be introduced only by means of the CLIP tester. This is possible only
if when setting the contact on, the anti starting indicator blinks rapidly, this being confirmed by the
state:
10G ANTI STARTING ……………………………………………….ACTIVE
After getting from DACIA database the repairing code (based on the vehicle chassis series
and on the code from the vehicle’s key head), perform the following operations.
1. Connect the CLIP tester to the diagnostic socket and to the battery (or to the lighter
socket) of the vehicle.
2. The anti start up indicator must blink slowly , the contact being taken off.
3. Set the contact in “M” position. The indicator must blink rapidly.
4. Select vehicle type “B41”;
5. Select the menu “ COMPUTER TEST” then select “ ANTI STARTING”.
6. In the menu “STAT E LIST” find the state 10G “ANTI STARTING” which must be
“ACTIVE”. 7. Access “COMMAND MODE” then select “ACTUATORS”.
8. Select the command “ MANUAL CODE INTRODUCTION” where you will write the
repairi ng c ode (form ed of 4 fi gures), then validate it with t he ke y “ ENTER”. The message
“COMMAND IN PROGRESS” will be displayed followed by the message “FINISHED
COMMAND”. 9. Now the procedure is finished and you may start the vehicle engine.
AT T E N T I ON!
Yo u may perform three attempts of introducing the repairing code; if after the third
essay the code is not yet valid, wait for 15 minutes, take off the contact and then set it
again, then other three attempts may be performed.
REMARK:
This procedure does not decode the injection computer, but is only allowing the start
of the vehicle’s engine. After 10 minutes have passed from the first introduction of the
r epairing code or after the disconnection of the battery, the vehicle’s engine cannot be
s tarted unless a new repairing code is introduced.
vnx.su
Page 570 of 891
82
ACCOUSTIC WARNING - ANTI STARTING
82 - 27
Diag nostic
ALP2. CONTACT SET ON THE ANTI STARTING INDICATOR BLINKS
(THE ENGINE IS NOT STARTING)
RECOMMENDATION -
Set the contact on.
Connect the CLIP tester.
Is there any communication with the E.C.U.
decoder ?
S ee ALP1.
Check the fuse F03 for anti starting bushing
supply.
Is it good?Replace the fuse.
Set the c ontact on and check if the state 4D
becomes ACTIVE ?
Is th e state 19 D PASSIVE ?
Perform « Procedure for replacement
E.C.U. decoder and memorising anti
starting code » if the starter is new ;
if it’s not new, replace it.
Set the contact off. The anti starting indicator
will start to blink after 10 seconds.(ACTIVE
an ti starting ).
Set again the contact and check: the failure
« Defective communication decoder bushing ».
Does exist such a failure ?
Study « DEFECTIVE
COMMUNICATION BUSHING
– DE CODER » from the chapter
DIAGNOSTIC.
Study « STATE 4D : SUPPLY +12
V » from chapter DIAGNOSTIC.
Try the engine starting with the second key.
Is the engine starting ?Replace the first key.Yes
Ye s
Yes
Yes
Yes
Yes
No No
No
No
No
No
vnx.su