fuse box DACIA SOLENZA 2004 User Guide

57
57 - 4
INSIDE ACCESSORIES
19 20
17 16
15
18
Remove the access cover of the fuse box.
Di
smount the three a ttachment screws (14)
of the fuse box.
21
14
Remove the access cover to the fuse box.
Swing over the little caps from the dashboard
lower part and dismount the attachment screws
(15) on the driving post cross member.
Dismou nt :
- attachment scre ws (16) of the climate
maintenance p anel on the lower part dashboard;
- attachment screw (17) of the lower part
dashboard on the vent-AC distributor (RACV);
- attachment screws (18) of the lower part
dashboard on the driving post cross member;
-upper attachment screws (19) of the
lower part dashboard on the driving post cross
member.
Extract :- headlamps adjustment knob;
-cigarette lighter.
Detach from clips the connectors: - hazard;
-r
ear window defrosting.
Disconnect the connectors:
- cigarette lighter;
-r ear window defrosting.
Di smount the attachment nut (21) of the
headlamps adjustment control.
Disconnect the connectors:
- hazard;
- climate maintenance control.
D etach from clips the l eft a nd right side
aeration ducts.
Take out t he dashboard from cockpit.
Dashboard
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 6
Lamps failures diagnostic
FOG LAMP NOT WORKING
Ye s
Ye s
Ye s Ye s
No
No No
No
Replace fuse F06
Replace the STOP contact
Replace fuse F19
Replace under steering
wheel control. Check fuse F06 from cockpit fuse box.
Is it worn?
Check the continuity and resistance against vehicle mass between:
- exit fuse F06 pin2 reverse driving contact c onnector
- pin1 reverse driving contact connector pin 6 right rear lam
connector
- pin 4 right rear l amp connector vehicle m ass
Ar e they good?
Defective wiring. Fix it.
Check fuse F19 from cockpit fuse box. Is
it worn? Check the continuity and
resistance against vehicle mass between:
- battery pin B2 light control lever and signaling,
- pin A3 inlet fuse F19,
- exit fuse F19 pi n 1 left rear lamp connector,
- pin 4 left rear l amp connector vehicle m ass.
Ar e they good?
Defective wiring. Fix it.

REAR DRIVI NG LAMP NOT WO RKING
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 7
Lamps failures diagnostic
STOP LAMPS NOT WORKING
Check fuse F04 from cockpit fuse box.Is it good?
Replace fuse F04Yes
Yes
No No
No
Ye s
Replace t he Stop contact
The stop contact wire supply is broken or disconnected. Fix it. Bridge the Stop contact terminals.
Are the lamps working?
Is the Stop contact supplied ?
The stop contact wire supply is broken or disconnected. Fix it.
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 8
DISMOUNTING
Disconnect the (-) plug of the battery.
Pull the seat ( 1) of the access flap ( 2) to the fuse box located in the cockpit, at the l eft end of
the dashboard. Carefully remove flap ( 2).
Dismount the attaching screws ( 3) of the fuse box on the driving post crossbeam and detach
it from clips (4)
R EMOU NT I NG
Attach in clips ( 4) the fuse box on the driving post crossbeam and mount the screws ( 3).
Carefully mount, the access flap ( 2) to the fuse box.
Connect the battery (-) terminal.
Perform functional tests, noticing the correct operation of all consumers supplied by means
of the cockpit fuse box.
OBSERVATION:
For vehicle equipped with programmable radio-tape player and electronic c lock, af-
ter battery reconnecting, the radio code must be introduced and the clock re-programmed.
If COBRA 3800 or COBRA 3900 alarms have been mounted on the vehicle, in the
fuse box, may be found fuses F29 with value 15 A (mounted in seat (5)) and F 30 with
value 5A (mounted in seat (6)).
Cockpit fuse box
2
1
4
4 3
35 6
vnx.su

81
INSIDE AND REAR LIGHTING
81 - 9
Cockpit fuse box
The fuses are protecting the following electric circuits:
Fuse Symbol Fu se Protected circuit
number type
F01 Free
F02 PLAF 15 A Instrument panel, cockpit UCE(ceiling lamp operation, radio
F03 20 ACockpit UCE, air conditioning climate control panel *
F04 15 ACockpit UCE, diagnostic socket, airbag UCE, anti-starting
bus h ing
F05
UC E10 A UCE injection , petrol pump relay/ignition coil, instrument panel
INJECTION
F06 10 AWindscreen wiper-washer switch (windscreen washing pump
operation), reverse driving switch, STOP switch, air
conditioning climate control panel*
F07 20 AWindscreen wiper-washer switch, UCE cockpit (windscreen
wiper timer operation), windscree n wiper motor (sto ppi ng at fix point).
F08 7,5 ALeft meeting lights, instrument panel (indicator)
F09 7,5 ARi ght meeting lights
F10 7,5 ALeft road lights, instrument panel (indicator)
F11 7,5 ARight road lights
F12 15 AAcoustic warning
F13 25 AUCE cockpit (turning lights and hazard), diagnostic socket.
F14 7,5 AFront/rear left parking lights, lighting: switches, climate control
panel, instrument panel, lighter, radio.
F15 7,5 AFront/rear right parking lights
F16 15 ALighter, radio
F17 30 AClimate control blower
F19 7,5 AFog lamp, instrument panel (indicator)
F20 25 ARear window defrosting
UC E
F21 INJECTION 5 AUCE injection
F23 30 ARight/left electric window regulator switch
F26 30 A Air conditioning climate control blower*
F28 20 AFog projectors
* for vehicles equipped with air conditioning
vnx.su

INSIDE AND REAR LIGHTING
81
81 - 10

DE SCR IPTION OF THE OPERATION
Dismount the battery (-) terminal;
Dismount the access flap to the cockpit fuse box;
Dismount the attachment screw of the UCE decoder and relays assembly.
Lift from its attachment place and remove UCE decoder and relays assembly.
UCE decoder protection
1 2
Carefully insert UCE decoder-relays assembly in the protector ( 1) so that protector is not
damaged.
Attach the protector to the front wiring by means of an attachment clip (2).
Mount the UCE decoder – relays assembly in t he attachment place.
M ount the attachment screw of the UCE decoder and relays assembly.
M ount the access flap of the cockpit fuse box.
Connect the battery (-) terminal.
AT T E N T I O N !
At any intervention implying dismounting of the UCE decoder-relays assembly, the
protector and t he attachment clip are to be replaced.
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 6
All new decoders, are not coded. After mounting on the vehicle, it is necessary the memorisation
of the key head code by the decoder in order to be operational. If only the decoder is replaced, no
intervention is necessary to the injection computer, which will keep the old anti starting code. When
the vehicle is provided with RF remote control for blocking/unlocking the doors, the performing of
the resynchronisation of the keys with the decoder is imposed, after its mounting. If further to the
di ag nostic of the anti starting system, using the CLIP tester, the replacement of the decoder is
imposed, proceed as follows:
DISMOUNTIN G
- disconnect the (-) terminal of the battery;
- d ismount the ECU decoder-relays assembly;
- ro tate the ECU decoder assembly, in order to have access at its rear connectors;
- d isconnect the front wiring connector from the E.C.U. decoder;
- deta ch ECU decoder from clips of the relays-ECU decoder support.
REMOU NT I NG
- attach in clips the new E.C.U. decoder in the support, connect the front wiring connector to
the ECU decoder, then attach the assembly on the driving post cross member in its place and
mo unt its attachment screw;
- remo unt carefully the access flap of the fuse box;
- reconnect the (-) term inal of the battery.
Proceed then to the insertion of the anti starting code using the contact key, then to its me morising
(va lidation) in the E.C.U. decoder, using the CLIP tester. For this purpose, perform the “E.C.U.
decoder replacement procedure and anti starting code memorising”. Check then the correct operation
of the anti starting system with both keys.
ATTENTION!
Once the decoder has memorised the key codes, this code cannot be erased or replaced
with another one.
If it is necessary the replacement of the kit (E.C.U. decoder and two key heads), then the “ Kit
replacement procedure” must be performed.
Dismounting - remounting E.C.U. decoder
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 18
Diag nostic
FA ILURES AND STATES INTERPRETATION
1. FAILURE OF COMMUNICATION CLIP TESTER/ E.C.U. DECODER
RECOMMENDATION Check if the lines K and L are not disturbed by another computer of the vehicle.
Check the condition of fuse F 03 from the cockpit fuse box.
Replace the fuse if necessary.
Check if the CLIP tester is not the cause of the failure; check if the tester is communicating
with another computer of the same vehicle (injection computer).
M easure the tension of the vehicle’s battery (U> 12,3V). If necessary, charge the battery.
Check if the E.C.U. decoder is correctly connected to the vehicle’s wiring.
Check the right supply of the E.C.U. decoder:
-presence of the mass at pin A8 of the E .C.U. decoder
- supply + I.C. at pin A9 of t he E .C.U. decoder
Be sure that the diagnostic socket i s proper supplied, according to the circuit diagram.
Check the continuity and the isolation of the electric wiring on the corresponding pins layout.
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the connection tester CLIP – E.C.U. decoder can’t be established, then replace the decoder.
AFTER REPAIRING After establishing the communication with the tester, fix the
possible failures.
Perform a conformity checking.
{ }
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 22
Diag nostic
5. FAILURE : DEFECTIVE COMMUNICATION ANTI STARTING SYSTEM -
E.C.U. DECODER
RECOMMENDATION -
Check the continuity and the isolation related to the mass and + 12 V voltage of the wiring
between the anti starting system pin 4 pin A2 E.C.U. decoder
Fix it if necessary.
Check the anti starting bushing supply : + 12V to the pin 3 and the mass to pin 2.
Di sconnect the E.C.U. decoder and measure the presence of +12 V at the pin A2 of the
decoder, the contact being taken off. If there it isn’t +12 V, check the fuse condition F03 from
the cockpit fuse box.
If the problem persists, replace the anti starting bushing.
Set the contact on and perform the impulse detection test at the pin A2 of the E.C.U. decoder.
Is there an impulse ?
YES
NO Replace the anti starting bushing.
Replace t he E.C.U. decoder.
Remove the memorised
failures by means of the CLIP tester.
AFTER REPAIRING Perform a conformity checking.
Check the operation of the anti starting system .
vnx.su

82
ACCOUSTIC WARNING - ANTI STARTING
82 - 26
Diag nostic
FAILURES LOCATING BASED ON CLIENT CLAIM
(algorithm for damage locating)
A LP1. MISSING COMMUNICATION CLIP TESTER / E.C.U DECODER
RECOMMENDATION Check if the lines K a nd L are not perturbed by another computer
of the vehicle.
Check the condition of the F03, F04 fuses from cockpit fuse box.
Be sure the CLIP t ester is not the cause of t he failure, by trying the communication with
another computer of the vehicle.
Check the tension of the battery (U>12,3V). If it is necessary, charge the battery.
Check the correct c onnection of the E.C.U. decoder to the wiring.
Check the supply of the E.C.U. decoder : - mass at pin A8; - supply (+IC) at pin A9.
Be sure that the diagnostic socket is correctly supplied.
Check the continuity and the isolation of the electric wiring on the pins’ line corresponding to:
E.C.U. decoder A3 7 diagnostic socket
A4 15
If the dialogue CLIP tester – E.C.U. decoder cannot be established, then replace the decoder.
When the communication with the tester is established, solve the
AFTER REPAIRING failures displayed by CLIP.
Perform a conformity checking.
vnx.su