lock DACIA SOLENZA 2004 Manual Online

57
57 - 11
INSIDE ACCESSORIES
Handb rake case
DISMOUNTIN G
Through the cutting out existent in the cock-
pit carpet in the handbrake lever, dismount the
attachment screw (1) of the handbrake case in
front part, on the tunnel.
Move towards front the seats.
Dismo unt :
- bench seat ( see c hapter 75); - attachmen
t screws of the front safety belts
at lower part; - attachment screws of the locks on the tun-
nel;
Detach from clips the carpet and roll it towards
front part.
Dismount the attachment screw ( 2) of the
handbrake case on the tunnel, in the rear part. Release the handbrake c ase.
REMOU NT I NG
Perform the dismounting operations in the re-
verse order. The safety belts screws are to be tighten to the
required moment of 2,7 daNm.
vnx.su

59
SECURITY ELEMENTS
59 - 1
F ront safety belts
1
4
3 2
TIGHTENING MOMENTS(daNm)
Fr
ont safety belt attachment screw 2.7
DISMOUNTING
Di smount:
-front/r ear door gasket (in the
contact area w ith the middle pillar
covering); -attachment scre ws (1) and (2) of
th e front safe t y be l t t o the uppe r pa rt,
conse quently, to th e lowe r part , on the
middle pillar lining; -
middle pillar c overing (see chapter
71); -attachment screw (3) of the safety belt
retriever on the middle pillar l ining. Dismount t he a ttachment scre w (4) of the
saf ety belt lock on the tunnel.
REMOUNTING
Perform t he di smounting operations in the
reverse order, taking into considera tion the
following: -retriever gui ding on t he centeri ng part
welded on the pillar. -the require d t ighte ni ng mome nt of
front the safety belts attachment screws is of
2,7 daNm.
vnx.su

62
AIR CONDITIONING
62 - 9
Cold air blowing device (DSAF)
Disconnect the climate maintenance blower
connector ( 11) (pull the red part towards arrow
A).
Di smount the attachment screws of the
steering wheel half-case and release from clips
detaching. Dismount the upper part dashboard and
release it from clips.
Dismount the radio-cassettes player. Disconnec t t he c entra l l ocking swi tch
connector (if the vehicle is provided with central
locking). Dismount the right air vent.
Dismount the DSAF attachment screws on
cowl panel and a ttachment screws on climate
maintenance box and release it.
Di smount the attachment screws ( 9) o f the
connection pipe ( 10) on the distributor of RACV
AC-ventilation air and release it.
REMOU NT I NG
Perform the dismounting operations in the
reverse order, taking into consideration that filter
reservoir is to be mounted the last. Fill the air conditioning unit with refrigerant
fluid HFC 134a (0,600 Kg).
86
11
Connector
Pin Denomination 1 Control + air recycling
2 Control + air recycling
3 Blower control speed 1
4 Blower control speed 2
5 Blower control speed 3
9 Climate control blower speed signal
10 Supply + after contact
11 Supply + after contact
12 Blower control speed 4
14 Mass
15 Mass
915
5 1
vnx.su

62
AIR CONDITIONING
62 - 15
Filter reservoir
Filter reservoir (1) is attached by means of a
support collar on the right longitudinal girder.
Its function in the AC unit operation is : -filtering the refrigeran t fluid;
-r etaining the humidity from the unit;
-f orming of a buffer stock of refrigerant
fluid.
The particles interception is necessary because
it might block the thermostatic expansion vale
operation or produce compressor mobile parts
wear or gripping. The filter reservoir is not to be repaired.
DISMOUNTIN G
Disconnect the battery.
Drain the AC unit.
Dism ount t he pi pi ng a nd pro t e c t wi t h
protection caps in order to avoid humidity
penetration. Dismount the filter reservoir off the support
collar and release it.
REMOU NT I NG
Perform the dismounting operations in the
reverse order. Fill the AC unit with refrigerant fluid HFC
134a (0,600 Kg) by means of the c harging
station.
Check for refrigerant fluid leaks.
When replacing the filter reservoir, fill in
the circuit with 15 ml of oil PA G S P 10 .
REMARK
The tightening required moment of
the pipes nuts at the filter reservoir is of
1,4 –2 daNm.
The required tightening moment of
the attachmen t screw of the filter
re servoir support is of 0,7 daNm.
1
vnx.su

CARRIAGE BODY INSIDE TRIMS
71
71 - 8
1 – cockpit carpe t
2 – clip
DISMOUNTING
Di
smount :
- front seats ( see chapter 78 );
- rear bench seat (see chapter 78);
- front seat belts lockers ( see chap-
ter 59 )
- centra l console ( see chapter 58);
- distributor of the air ventilation/cli-
mate maintenance RACV (see chapter 61 );
- front safety belts at lower part;
- accelera tion pedal limiter.
D etach from clips the cockpit carpet ( 1).
REMOUNTING
Perform the dismounting opera tions in the
reverse order.
The clips attaching is to be performed with
a maximum forc e of 3 daN.
Cockpit carpet
1
2
vnx.su

72
72 - 1
LATERAL OPENINGS TRIMS
Front door panel
DISMOUNTIN G
Disconnect the battery.
Dismount :
- window regulator crank (A) for glass
lifting , that is mounted by clips attachment on
the window regulator axle ( in case of the
vehicles provided with glass hand-drive lifting);
- attachment screw of the open ing
mechanism from inside (B), consequently the
mechanism. - locking handle (C) attached by screw.
Rotate the speaker grill (D) counter clock-
wise direction and extract it from the front door
panel.
Dismount the four attachmen t screws of the
s peaker on the door pa nel.
Disco n n ect the front door speaker
connector. Dismount the attachment screws (1 ) of the
door panel on the caisson.
D C
1
1
CD 1
2
B
A
Detach from clips the door panel in poi nts
(2) .
R EMOU NT I NG
Perform in the reverse order the dismounting
operations taking i nto account t he following
recommendations: - check the integrity of the deflective
panel and of the continuos layer of Romtix
1502 P sealing materi al on the front door
caisson; - for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is blocked;
- after mounting, check the operation of
the inside opening mechanism and its alignment
with the front door panel; - check t he ope ration of t he front door
speaker.
vnx.su

72
72 - 2
LATERAL OPENINGS TRIMSRear door panel
1 C
B
1A 2
C
2
DISMOUNTIN
G
Dismount :
- window regulator cra nk (A) for glass
lifting that is mounted by clips attachment on
the window regulator axle.
- attachment screw of the inside opening
mechanism (B), consequently, the mechanism;
- locking handle (C) attached by screw;
- attachment screws (1) of the rear door
panel on the caisson; Detach from clips the rear door panel from
points (2).
REMOU NT I NG
Perform the dismounting operations in the
reverse orde r, taking into considera tion the
followings recommendations: - check the integrity of the deflectiv e panel
and of the continuos sealant material layer
Romt ix 1502 P on the door caisson outliner;
- for the mounting of the inside opening
mechanism, the opening control rod will be
placed in the position where the assemble d plate
with electric control is unblocked. - after mounting, check the operation of
the inside opening mechanism and its alignment
w ith the rear door panel.
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 3
DISMOUNTING
After identification and elimination of the real cause of the battery discharging, proceed as
follows: Remove the plastic protector from the plus plug of the battery.
Dismount the attachment nut of the mass wiring from the minus plug of the battery.
Dismount the attachment nut of the wiring from the plus plug of the battery.
Dismount the battery attachment clamp screw.
Carefully take off the battery.
R EMOU NT I NG
Perform the dismounting operations in the reverse order. After that, reset the radio by intro-
ducing the radio code (if the vehicle is equipped with radio) and adjust the dashboard clock.
Battery
vnx.su

80
BATTERY - FRONT HEADLIGHTS
80 - 11
Disconnect the (-) plug of the battery;
Dismount
the headlamp adjusting control from the turning lamp-headlamp assembly:
- pull backward the gasket of the headlamp adjustment corrector ( 1);
- detach from clips the protector (2) of the headlamp adjustment mechanism;
- loosen the locking nut ( 3);
- detach from clips the he adlamp adjustment control cable ( 4) from the headlamp
adjustment corrector and then from the fork (5);
Dismount the headlamp adjusting control from the other turning lamp-headlamp assembly .
Detach from clips the headlamp adjustment control cables and cut the attachment collars.
Dismount the headlamps adjustment control button.
Dismount the attachment nut of the headlamp adjustment control on the dashboard.
Dismount the bonnet opening control cable from the opening handle (see chapter 52).
Detach from clips, by means of a straight screwdriver, the cables passing bushing from the
cowl panel.
Remove the headlamps adjusting control cables from the cowl-passin g hole. Mark the mounting
position of the headlamps adjustment control cables.
REMOU NT I NG
Insert the headlamps adjusting control cables through the cowl-passing hole, observing the
existent position prior to dismounting.
Insert the bonnet opening control cable through the cables passing bushing.
DISMOUNTIN G1
2
V
56 34
Replacement of the headlamps mechanic adjustment control
vnx.su

BATTERY - FRONT HEADLIGHTS
80
80 - 12
Replacement of the headlamps mechanic adjustment control
Attach on the cowl panel, by means of clips, the cables passing bushing, ensuring the cockpit
co mpartment sealing against possible water drain along the cables passing bushing.
Mount the bonnet opening control cable in the opening handle (see chapter 52). Position the
headlamp s adjustment control on the dashboard.
Mount the attachment nut of the headlamps adjustment control on the dashboard.
Mo unt the headlamps adjustment control button and turn it in the position “3”.
Mount the headlamp adjustment control to a turning lamp-headlamp assembly :
-a ttach in clips by means of a straight screwdriver, the headlamp adjustment control cable
in fork (5) a n d t h en in the headlamp adjustment corrector;
- tighten initially the cable by hand till the fork ( 5) is in contact with support ( 6) so that fork
is remaining at max. 0.5 mm again st the support;
-block the headlamp adjustment cable by means of the nut ( 3);
-a ttach in clips the protector ( 2) o f t h e headlamp adjustment mechanism;
- position correctly the gasket of the headlamp adjustment corrector – the vertical adjustment
screw ( V) mu st come out through the gasket.
Mount the headlamp adjustment control of the other turning lamp-headlamp assembly.
Attach in the attachment points, by means of clips, the headlamps adjusting control cables,
replace and mount the attachment collars, observing the mounting position prior to the dismounting.
Keep a distance of approximate 40 mm
± 10 mm between the right cable and the cylinder
no .1 spark plug cable, in order to avoid the loses due to electric-magnetic induction.
Reconnect the battery ( -) term inal.
Switch on the headlamps and check the operation of the headlamps mechanic adjusting control.
The adju stment of the luminous spot dip of the headlamps in the downward sense of the vehicle
loading condition is to be performed by bringing the headlamps adjusting button in the “ 0” position
an d then in the desired condition.
REMA RK : The r equired tighteni ng moment of the attachment nut of th e headlamps
adju stment control on the dashboard: 2 Nm.
vnx.su